Search Documents

By C. A. Heberlein

C. A. HEBERLEIN,* New York, N. Y.-The results stated by Rey and Brevers are so startling that they are of great interest, as the concentration of a low percentage of cinnabar by differential flotation yields a high-grade concentrate in the presence of either arsenical or iron pyrite. The authors say: "Cyanide can thus be used to depress arsenopyrite and make a good cinnabar-arsenopyrite separation. A cinnabarpyrite separation could probably be effected in the same way." Corrosive sublimate at the present price of mercury would be a very expensive reagent but the expense would be justifiable if a high rate of concentration could be obtained with a high extraction. On my request, special tests were made in the Punitaqui mill in Chile along the line suggested by the authors, without any improvement of either grade or extraction. As the recovery of the cinnabar in a complex sulphide of chalcopyrite and pyrite gave unsatisfactory results, I had tests made at the testing laboratory of the American Cyanamid Co. at Stamford, Conn. As these tests turned out to be highly satisfactory, not only at Stamford but later at the mine, they are presented here. [AMERICAN CYANAMID TEST FEED PER CENT Si02 66.54 A12032.08 CaO0.70 MgO 0.00 Alkalis1.78 Fe15.63 Cu0.44 S9.42 Hg0.45 OZ. PER TON Ag0.95 Au0.151 Screen Analysis of Tailings, Per Cent Plus650.0 Plus 1001.32 Plus 15020.75 Plus 20019.85 Minus 20058.08] The pulp had a density of 22 and a pH of 7.8. Total time of conditioning was one minute. The reagent added was Texas fuel oil, 0.116lb. Of 33.7 Bé. gravity containing 0.9 per cent sulphur. Frother, 0.062 lb. of No. 5 pine oil. Rate of concentration of mercury was 25.7: 1 [ ]

Jan 1, 1941

By T. L. Joseph

BLAST furnaces are most efficient thermally when the C02 in the top gas is highest. Oxygen introduced in the air blast is converted to CO in the combustion zones. The extent to which CO, generated in front of the tuyères, is converted later to C02 depends upon the ratio of ore to coke in the charge and the degree to which C02, formed by reduction of iron oxides with CO, reverts to CO by the secondary reaction C + C02 = 2C0. About 300 to 400 lb. of carbon1 per ton of pig iron is normally involved in the solution-loss reaction or direct reduction of FeO with carbon, which produces the same over-all results; that is, lower C02 in the top gas. Riche has recently reported a reduction in fuel consumption at slower rates of blowing on two furnaces in spite of higher heat losses per ton of iron. Lower fuel consumption at slow operating rates was due to more complete reduction of the ore that resulted in higher C02 in the top gas and consequently more efficient use of carbon. Kinney3 has reported substantial savings in fuel as a result of crushing and sizing the ore charge. Improvements in practice brought about by sintering magnetite concentrates, flue dust and fine ores have been due to the establishment of conditions favoring more complete reduction of the ore in the upper part of the furnace. The extent to which oxides and fluctuations in composition in pig iron affect the quality of steel and finished product needs further study. There is evidence that more thorough preheating and reduction of the ore in the upper part of the furnace tend to give a better quality of iron. Bogatzkii4 found from laboratory work that the amount of oxygen enter-

Jan 1, 1936

By W. G. Fischer

Basic laboratory tests on trona and the surrounding shales initiated the Rock Mechanics program. The stress-strain curve, modulus of elasticity, Poisson's ratio, the uniaxial rock strength, Mohr's envelope, the biaxial stresses at failure, and creep were investigated. A series of underground problems were then approached using this information and various field measuring devices, most of which were developed by the Bureau of Mines. Initially, stress concentrations near mine openings were evaluated using the stress relief technique. This required an accurate determination of the pre-mining stress field. Later, stress concentrations associated with the cave line were studied. After about 30 stress reliefs over an appropriate time interval the effects of one type of mining could be compared against another. The microseismic technique was used to investi- gate a possible application of warning devices near the cave line. A study of mine reorientation was made. Problems related to the shape and size of pillars and barriers were studied. The effectiveness of roof bolting patterns was examined. Control of roof stresses was attempted. A new system of mining in heavy ground has been developed using the information secured in the Rock Mechanics program. Without this system, mining in more than one instance would have been next to impossible. Indeed, from this one discovery alone, the Rock Mechanics program has paid off in improved safety as well as in dollars. The Westvaco trona* mine is located near the town of Green River in the southwestern corner of Wyoming. It is owned and operated by FMC Corp. on land leased from the US Government, the State of Wyoming, and the Union Pacific Railroad. A conventional room and pillar system is being used, (Fig. 1) with complete removal of the pillars during final mining. Return air bleeders surround

Jan 1, 1964

By G. C. Waterman, W. E. Hawes

Mr. Grieves' paper on "Shaft Sinking Today --A Boring Business Tomorrow" in the Dec. 1981 issue of MINING ENGINEERING is an excellent description of recent improvements in speed and costs of shaft sinking. However, shaft boring techniques are not a recent development. In 1935-36, the Idaho Maryland Co. (gold), Grass Valley, CA, bored the vertical 1.5-m-diam Idaho No. 2 ventilation and supply shaft to a depth of 346 m. The equipment was designed and perfected by Branner Newsome and was, I believe, described in "Transactions." Pickands Mather later bored a 1.8-m-diam shaft to a depth of about 305 m using Newsome's design. The Idaho No. 2 shaft cut through hard gabbro, diabase dikes, soft serpentine, very incompetent ankeritized serpentine and a strong fault zone. The completed shaft did not require timber support; the fault zone was cemented. Equipment consisted of a rotating 1.5-m or 3-m core barrel with a slotted bottom which cut a 76-mm kerf. The cutting agent was chilled steel shot introduced into the slot as needed. The driving mechanism and core barrel were lowered into the shaft, the former secured to the wall and the inshaft "engineer" operated the motors which controlled core barrel rpm and advance. After an advance of 1.5-3 m the equipment was lifted out of the shaft, a half(?) stick of powder cut off the drilled core, and it was hoisted to the surface with a cable attached to an eye bolt at the tope of the core. A "shift" consisted of three men: hoistman, equipment operator (down the shaft), and a surface laborer. Advance was variable as equipment and techniques were perfected. Near the end of the job advance was, as I remember, 1.5-3 m per shift. Costs were, as I recall, about $115/m. Up to 4 m cores were lifted out in one piece and swung to the dump by a stiff leg derrick. The Newsome equipment was relatively inexpensive to build and operate and his method should be (more than?) competetive with the methods described by Grieves.

Jan 1, 1983

By Cyril Smith

A COMPLETE discussion of the literature on the subject of the influence of copper on iron and steel will be published elsewhere.1 The present paper is concerned especially with the precipitation-hardening of copper steels, and brief mention will be made here only of the work of Kin-near,2,3 Nehl4 and Buchholtz and Koster,5 who alone have studied this phase of the subject. Kinnear found that normalized low-carbon steel castings containing about 1.0 per cent copper on drawing at temperatures in the neighbor-hood of 530° C. (1000° F.) increased in tensile strength and yield point, with little decrease in ductility. The maximum effect was obtained with about 0.9 to 1.0 per cent copper, and when the copper exceeded 3 per. cent no improvement occurred on reheating. Kinnear did not study the effect of time of reheating-an all important factor where precipitation is concerned. Nehl,6 who apparently was unaware of Kinnear's work, recognized the change as due to precipitation and studied the interdependence of time and temperature of reheating, the temperature of the initial solution heat treatment, and the speed of cooling necessary to retain the bulk of the copper in supersaturated solu-tion and to give an increase in hardness and tensile strength on reheating. Nehl found that if the final rolling or forging temperatures exceeded 700° C. (1300° F.) it was not necessary even to normalize the steel, but full precipitation occurred on merely reheating the forged or rolled shapes at 500° C. (930° F.).

Jan 1, 1933

By T. M. Chance

THE necessity of adopting improved methods of bituminous-coal cleaning at. many collieries is recognized by all familiar with the requirements of the various bituminous markets, the approaching exhaustion of the relatively small areas of inherently high-grade-coal, and the difficulties encountered in maintaining a uniform grade of shipped coal. Many coals lose much of their .market value by degradation in size, and, in any event, if the cleaning process is to contemplate wetting the coal the minimum amount of fines should be produced to prevent sludge losses and the difficulties resulting from the moisture content of the wet fines. Hence, it is desirable to by-pass the finer coal dry, if this can be done without too-great increase in impurities in the final product. This procedure has given excellent results at washeries at Steelton and in the Birmingham district. If the raw fines are too impure to permit admixture with the washed coal, it may be desirable to use dry methods, such as the pneumatic table, rather than to wet an excessive amount of such fine material. The bituminous-coal cleaning plant should therefore: (1) Treat the raw coal in as large lump as possible and without sizing; (2) eliminate degradation of pure coal -in the washing process; (3) avoid wetting the fines, if possible; (4) produce washed coal practically free from mechanically included impurities; (5) crush the refuse and retreat, if much intergrown coal, and refuse are present, rather than precrush the entire feed. Ordinary gravimetric methods of concentration, whether hydraulic or pneumatic, will not meet all of these requirements, as the large lump includes those sizes. now sent to the picking tables, if it is desired to treat material of such size. I do not know of any prior commercial method, based on the falling velocity, coefficient of friction or resistance to fracture, that permits the production of clean coal varying in size from, say, 10-in. lump to 1/16 -in. mesh.

Jan 6, 1924

By A. U. Seybolt

A FEW copper-zinc-base alloys meet die-casting requirements reason- ably well, although improvements are desired. Aluminum bronzes, high-tinbronzes and some copper-nickel-zinc alloys can be die-cast, accordingto Herb,1 but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. TABLE 1. Commercial Die-casting Brasses a Constituent Yellow Brass Low-silicon High-siliconb Brass Brass Nickel Silver Composition, Per Cent Cu 57-59 63-65 80 -81.5 42.0 Zn 40-42 33-35 13.5-16.0 41.0 Sn 0.5-1.5 Si 0.75-1.25 3.75-4.25 Pb 1.0 Ni 16.0 Properties Tensile, lb. per sq. in.. 55,000-60,000 65,000-70,000 85,000-95,000 85,000-95,000 Yield, lb. per sq. in.d.. 30,000-35,000 35,000-40,000 65,000-70,000 65,000-72,000 Elong., per cent in 2 in . 15-20 20-30 8-12 10-20 Brinell hardness 120-130 120-130 160-180 160 Specific gravity 8.47 8.50 8.15 8.45 Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy, 3,4 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. c Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb' as 1650° F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600° F., and of the nickel silver as 1675° F. d Criterion not stated.

Jan 1, 1939

By Rossiter Raymond

(Butte Meeting, August, 1913.) ON Mar. 28, 1913, the Board of Directors of the American Institute of Mining Engineers unanimously adopted the following Minute: JOHN FRITZ, one of the most distinguished of American mechanical and metallurgical engineers, won that position by the force of innate genius, indomitable industry, unstained integrity and unfailing sympathy, and generosity towards his fellow-men. Self-educated in the hard school of practice, he appreciated nevertheless the advantages of technical instruction and discussion, and evinced this appreciation both by his membership and lively interest in this and other similar societies, and by his munificent gifts to engineering education at Lehigh University, and his long and faithful service us a Trustee of that institution. . As one of the foremost of those American engineers who, through their brilliant inventions and practical skill. developed here -the modern iron blast-furnace -and rolling-mill, and introduced and perfected the Bessemer process and other improvements in the manufacture of steel, Mr. Fritz contributed mightily to the chief departments of that industrial progress which characterized the Nineteenth Century. Proud of his great achievements, we cannot but rejoice over his long and fruitful life, crowned with a peaceful death ; but our praise and thanks are mingled with sorrow, as we recall the kindly face which we shall see no more on earth, and the loyal friendship and spontaneous good-will which led the love of his generation, and the reverence of the generation which followed, to regard him universally as " Uncle John Fritz." That. summary, though only an outline, is a good portrait ; and in the present sketch, we shall do no more than supply some details of the likeness, and some elements of the background.

Jan 6, 1913

By Sunder S. Saluja

Man had to learn to break rocks as early as the Stone Age, when they formed his main source of raw material. He started with chipping and over the years has reached a stage where he can employ atomic blasts and break, with one blast, millions of tons of rock. In between these two extremes there have been several stages of development including firesetting, use of the expansion of water on freezing in chipped cracks in cold climates, the use of low or deflagrating explosive black powder in about the 17th century, the use of high explosives with the discovery of nitroglycerine in 1846 by Sobrero, followed by the monumental discoveries of the great Swedish scientist Alfred Nobel in the latter half of the nineteenth century. The attempts to develop a stronger and still stronger explosive force were accompanied by investigations to understand the mechanism of failure of rock so that the force could be used to the best advantage; the latter, of course, have lagged far behind the former. This is mainly due to the fact that the chemical reactions involving high explosives as well as the processes resulting in the breakage of rock take place at too great a rate to be studied with the equipment that has been only recently available. Moreover, the development of stronger explosive forces was prompted by military necessities in the past and competition, at present, among highly developed nations. With the development, however, of the new techniques such as micro- second photography, microsecond flash radiography, extremely high-speed movies, strain gage assemblies, electronic chronographs and other improved electronic techniques, the investigator has in the last decade or

Jan 1, 1968

By A. L. Holley

The application of scientific methods to the investigation of natural laws and to the conduct of the useful arts which are founded upon them, is year by year mitigating the asperity and enlarging the outcome of human endeavor. More notably, perhaps, are these the facts in that system of productive and constructive arts of which engineering is the general name. In metallurgical engineering especially, within the period of our own recollection, how rapid has been the rate and how wide the scope of progress: the scientific discovery and mining of metalliferous veins; the economical separation and reduction of ores of every grade; the production and regulation of high temperatures; the varied improvements in the manufacture of iron, in saved heat and work, in uniformity and range of products; and, most important of all, the creation and the utilization, to be counted by the million tons a year, of the cheap constructive steels. Wonderful as this range and degree of development may appear to the public eye, the close and thoughtful observer must, nevertheless, conclude that neither the profession nor the craft of engineering may congratulate themselves too complaisantly, but that they should rather acknowledge to each other the embarrassing incompleteness of the union between engineering science and art. There is a small school of philosophers whom we may designate as original investigators, men who come close to nature, who search into first principles, and who follow that scientific and therefore fruitful method by which the relations of matter and force are discovered, classified, and brought within the reach of practice. These wonderful men do not indeed create the laws of nature, as they sometimes almost seem to, but they go up into the trembling mountain and the thick darkness and bring down the tables upon which they are written.

By T. L. Joseph

THE committee appointed to investigate the application of oxygenated air to the blast' furnace believes, after a careful study of the problem, that this enriched air will increase hearth temperature, tonnage, flexibility of operation, and quality of pig iron made, and that fuel consumption will be decreased. These improvements are supported by theoretical evidence; but a practical trial of the process is necessary to establish more definitely the magnitude of benefits realized. The commercial application, however, may profitably be preceded by a test on a smaller scale. A small furnace will, in general, respond to the enriched air in the same way as a commercial furnace and the magnitude of the benefits to be gained from varying additions of oxygen can be fairly well established at relatively little expense. A new experimental furnace, being built jointly by the Bureau of Mines and the University of Minnesota, at Minneapolis, will have a capacity of about 6 tons and will riot require more than 700 cu. ft. of natural air per minute. Its hearth is 36 in. in diameter and its height about 32 ft. Enough oxygen to enrich the blast to the extent recommended by the committee can be obtained from a small oxygen unit. It might even be cheaper to perform preliminary experiments with tanks of oxygen obtained from regular, dealers. A procedure in making the test that suggests itself is to start with operation on normal air; then to use blast, enriched in several steps. Systematic temperature measurements of the tuyeres, slag, and metal would reveal any changes in hearth temperature. When these changes become large enough, the burden may be gradually increased to just within the breaking point and the furnace brought back to normal, if possible, by the addition of oxygen. Such a test would show what might be expected in the way of a decrease in fuel consumption and the time taken to "straighten up" the furnace by means of oxygen. The new furnace at Minneapolis is so equipped that the furnace process can be observed from the stock line to the iron notch. We have been taking gas samples at various elevations in the furnace to study combustibility of the fuel and the reducing power of the gas. If either of these is affected by removing inert nitrogen, the change can easily be measured.

Jan 11, 1924

By Lewis Delano

IT HAS been generally recognized that, owing to the extreme friability of, galena, fine grinding has a tendency to cause excessive sliming of the mineral, so operators of lead mills have attempted to avoid this condition by commencing concentration at as coarse sizes as any mineral is freed. Jigging has been the basis of the milling process, making a clean coarse concentrate and a large amount of tailing, which was considered sufficiently low-grade to be rejected. However, developments and improvements in concentration processes are everywhere changing the low-grade tailing of yesterday into material worth retreating today. Investigations of the work of the Hancock jig on the Bonne Terre ore- have shown that the best results to be expected will give a tailing assaying 0.75 per cent. lead; the average over all conditions and grades of ore will be between .0.80 and 0.90 per cent. By crushing the jig tailings in ball-mills and retreating by tables and flotation, a tailing of considerably lower grade can be made; the problem then becomes an economic one of increased crushing costs versus higher recovery. In considering the entire elimination of jigging, the increased smelting charges; due to a greater amount of slime galena will be counterbalanced by the lower operating cost, in-creased recovery, and the many advantages of a simpler flow sheet. In developing these problems in the Bonne Terre mill of the' St. Joseph Lead Co., a long series of tests has been carried out covering every stage of crushing and concentration, and a large number of possible flow sheets were considered and tried. Only the final results and a few comparisons will be given here. At the same time, a careful and detailed cost-keeping system has enabled us to compare milling costs with the various flow sheets, and to calculate the economics of the problem' with great accuracy. .

Jan 8, 1920

By N. H. Mannakee

[Secretary's Note.—At the Spokane meeting of the Institute, in discussion of President Brunton's address on "Modern Progress in Mining and Metallurgy in the Western United States," and at the request of members present, Mr. Ayres gave an oral account of his new separator, which is here published as an independent paper, partly because of its inherent importance and partly because it describes an improvement which did not originate in the Western United States, and therefore does not fall, strictly speaking, under the title of President Urunton's address.—R. W. R.] A brief history of the growth of the anthracite-coal preparation will give a better view-point from which to judge the present problem of separating slate from coal. At the beginning of the commercial value of anthracite, 70 years ago, only the pure portions, or " splits," of the veins were mined and shipped to market, and without any preparation or screening other than the selection, while loading, of the glassy lumps, and the rejection of the fine material and the slate that had strayed accidentally into the coal. The next step was the crushing or breaking of the coal (hence the name "breaker" as applied to the preparation-building), and the sizing of it by means of bars or revolving screens. This stage of its development marked the advent of the " breaker-boy " as a slate-picker, with his ever-increasing capriciousness. As the richer veins or a splits " became exhausted and the market demanded a still greater output, the less-pure " splits " and the thinner veins were utilized to produce the coal. Carrying as they do a far greater percentage of impurities, particularly when removing the pillars, it became necessary to build new and better equipped preparation-plants. Finally, we are now at the highest stage of complicatioii yet known to the art of coal-preparation. We are dealing with varying specific gravities, frictional difference, hardness, structure, and form in the pieces of coal and slate coming from many different veins, and

Jan 1, 1910

By Rossiter W. Raymond

I DESIRE to call the attention of the Institute to a novel system of dredging, which, it seems to me, may prove applicable, not only to river and harbor improvements, but also to certain varieties at least of alluvial and diluvial gold mining; that is, river-mining, barmining, coast-mining, and any other similar operations now carried on by means of coffer-dams or dredging machines. The simple and effective method to which I refer is the invention of General Roy Stone, formerly an officer of volunteers, and at present a civil engineer, engaged under General Newton, of the United States Engineer Corps, upon the government works in New York harbor. General Stone has been, since September, 1878, in charge of operations upon Diamond Reef. This reef, lying between Governor's Island and the Battery, is one of the most dangerous in the harbor. Its position in the highway of navigation, and the fact that it is dangerous only to vessels of considerable draught and at certain stages of the tide, combine to increase the serious nature of the disasters which it has caused. The reef consists partly of rock in place, and partly of deposits of glacial clay, boulders, and pebbles, over all of which lies, or did lie until it was removed, the ordinary silt and rubbish of the harbor. As the purpose of the present paper has nothing to do with the special dimensions and other circumstances of this particular work, I describe those features only which are connected with General Stone's ingenious device. Various attempts have been made to remove the upper portion of Diamond Reef and secure a navigable depth at low tide. Some years ago Maillefert undertook to accomplish this by firing charges of high explosives, simply laid upon the surface. He accomplished some good in the removal of projecting points and ridges ; but as soon as the surface of the reef had become approximately level, his method was no longer effective. After the work had been taken up by the Engineer Corps, the well-known drilling-scow invented by General Newton was brought into action ; and, so long as holes could be bored and fired in solid rock, this process was effective enough. In the mixture of hard-pan

Jan 1, 1880

By T. M. Chance

THe necessity of adopting improved methods of bituminous-coal cleaning at many collieries is recognized by all familiar with the requirements of the various bituminous markets, the approaching exhaustion of the relatively small areas of inherently high-grade coal, and the difficulties encountered in maintaining a uniform grade of shipped coal. Many coals lose much of their market value by degradation in size, and, in any event, if the cleaning .process is to contemplate wetting the coal the minimum amount of fines should be produced to prevent sludge losses and the difficulties resulting from the moisture content of the wet fines. Hence, it is desirable to bypass the finer coal dry, if this can be done without too great increase in impurities in the final product. This procedure has given excellent results at washeries at Steelton and in the Birmingham district. If the raw fines are too impure to permit admixture with the washed coal, it may be desirable to use dry methods, such as the pneumatic table, rather than to wet an excessive amount of such fine material. The bituminous-coal cleaning plant should therefore: (1) Treat the raw coal in as large lump as possible and without sizing; (2) eliminate degradation of pure coal in the washing process; (3) avoid wetting the fines, if possible; (4) produce washed coal practically free from mechanically included impurities; (5) crush the refuse and retreat, if much intergrown coal and refuse are present, rather than precrush the entire feed. Ordinary gravimetric methods of concentration, whether hydraulic or pneumatic, will not meet all of these requirements, as the large lump includes those sizes now sent to the picking tables, if it is desired to treat material of such size. I do not know of any prior commercial method, based on the falling velocity, coefficient of friction or resistance to fracture, that permits the production of clean coal varying in size from, say, 10-in. lump to 1/16-in. mesh. The effect on the specific gravity of any given coal as a result of variations in ash and pyritic sulfur content is well known; in fact, it has been made use of in commercially ascertaining ash content by deter-

Jan 1, 1924

By A. L. Holley

THE application of scientific methods to the investigation of natural laws and to the conduct of the useful arts which are founded upon them, is year by year mitigating the asperity and enlarging the outcome of human endeavor. More notably, perhaps, are these the facts in that system of productive and constructive arts of, which engineering is the general name. In metallurgical engineering especially, within the period of our own recollection, how rapid has been the rate and how wide the scope of progress: the scientific discovery and mining of metalliferous veins; the economical separation and reduction of ores of every grade; the production and regulation of high temperatures; the varied improvements in the manufacture of iron, in saved heat and work, in uniformity and range of products ; and, most important of all, the creation and the utilization, to be counted by the million tons a year, of the cheap constructive steels. Wonderful as this range and degree of development may appear to the public eye, the close and thoughtful observer must, nevertheless, conclude that neither the profession nor the craft of engineering may congratulate themselves too complaisantly, but that they should rather acknowledge to each other the embarrassing incompleteness of the union between engineering science and art. There is a small school of philosophers whom we may designate as original investigators, men who come close to nature, who search into first principles, and who follow that scientific and therefore fruitful method by which the relations of matter and force are discovered, classified, and brought within the reach of practice. These wonderful - men do not indeed create the laws of nature, as they sometimes almost seem to, but they go up into the trembling mountain and the thick darkness and bring down the tables upon which they are written. * President's Opening Address. The discussion following this paper, and also the Joint Discussion of the Institute and the American Society of Civil Engineers, on the subject of Technical Education., are published in a separate volume.

Jan 1, 1876

By J. Parke Channing

THESE days of great industrial and social problems in America produce many suggested solutions and great changes. The practical engineer and employer of labor views these problems differently from the labor leader or the social reformer, but as never before he is sincerely interested in solving them in a way that will be just to all. The inevitable tendency of the day is toward "industrial betterment," "safety," "industrial education," "efficiency," and the many other things' which have become so familiar to progressive employers. There is no longer any question that these things are worth while from both the hu¬man and economic standpoints. They "pay" in dollars and cents. The very center of final success in improving conditions and increasing the efficiency of workingmen must be the spirit of fairness and a knowledge on the part of the employer of how to deal sympathetically and intelligently with his employees. Every progressive employer knows how greatly he desires foremen, superintendents, managers and others who possess these qualities. On the other hand, we are all familiar with serious mistakes made by young graduates of engineering schools who have had no opportunity to develop these qualities, and who have no real appreciation of the worth of the workers. Indeed, one wonders whether much ill-feeling, labor difficulties, and many strikes could not be avoided if such men had the right attitude. Is there any way of remedying this condition? If this particular difficulty can be solved, if these young engineers, many of whom are our coming leaders of industry, can be given the right perspective and the right understanding of these other problems in addition to fair, sympathetic methods of handling men, many of our other problems will be solved-not at once, but gradually and permanently, as these men make good and become influential in paths of industrial righteousness and industrial peace. Many progressive employers of to-day have enlarged their own perspective and realize the great importance of enlarging the perspective of those who shall follow them.

Jan 3, 1915

By Waldemar Lindgren

I. INTRODUCTION AT the time of the discovery of America the old world had a scant supply-of the precious metals. Both the northern and the southern part of the new continent proved wonderfully rich in gold and silver and its treasures were eagerly looted; though the looting has lasted four centuries, the nines of its mountain chains are far from being exhausted. Even the later discoveries in Australasia and eastern Siberia could not rob the Western Hemisphere of its position as the greatest gold and silver producing region of the world, though finally the developments in a narrow and circumscribed area in South Africa wrested from the Americas their supremacy in the production of gold. Nevertheless the history of the two parts of the great western continent has been strikingly different. At first the Spaniards extracted vast treasures of silver from Mexico, Peru, and Bolivia, while Colombia and some placer deposits in Peru yielded a smaller quantity of gold. A couple of centuries later, a stream of gold began to flow from Brazil, the silver production from the countries mentioned above continuing strong in the meanwhile. Later on, the yield of South America diminished, but to offset this there began a wonderful series of discoveries in North America. The gold fields of California astonished the world; and when the cream of these had been skimmed off there began a no less amazing development of the Central Cordilleran gold and silver districts, which soon wade the United States the greatest producer of the precious metals. Aided by ever improving technique, extensive exploration, and a system of railroads, the yield was maintained and increased. Still later followed the discoveries of the gold fields of the arctic region and silenced those who had maintained that the zenith in gold production had passed. Recently the province of Ontario in eastern Canada

Jan 4, 1916

By H. M. St. John

Like every present-day manufacturer, the brass foundryman is faced with the necessity of reducing the cost of his finished product without impairing its appearance or quality. He must use every economy that the progress of art and science puts at his disposal and should also be alert to profit by any peculiarity in his own situation or the nature of his product that may give him an exceptional advantage. Much can be accomplished by the adoption of labor-saving equipment and improved methods of melting, molding and handling. Control of pouring temperature, study of defective castings and their causes, laboratory control of molding sand and core mixtures, the use of less expensive alloys, all contribute to the desired end. Assuming that the composition of the alloy is already as inexpensive as the character of the casting will permit, still further savings can be made by the intelligent purchase and utilization of the metals needed to produce the desired analysis. Functions of Secondary and Virgin Metals in Casting Brass It is no longer a general assumption among foundrymen that quality castings must be made from an "all virgin" mix. If suitable secondary metals can be obtained more cheaply it is wasteful to use any larger proportion of virgin metal than is required to produce castings of the desired properties. To follow such a course, however, imposes upon the foundryman a heavier obligation than was formerly the case, to make sure by test and inspection that his castings really are of the desired quality. So long as he used the most expensive grades of metal and his melting practice was reasonably correct he was not obliged to give much thought to the quality of the metal in the castings. If he is to use secondary metals he must, in order to retain the confidence of his customer, examine these metals very carefully before use, exercise scrupulous control over his melting and pouring conditions and examine his castings closely. These statements apply more particularly to the jobbing foundry. The foundry department in a manufacturing plant is in a somewhat

Jan 1, 1930

By Rossiter W. Raymond

I desire to call the attention of the Institute to a novel system of dredging which, it seems to me, may prove applicable, not only to river and harbor improvements, but also to certain varieties at 1east of alluvial and diluvial gold mining; that is, river-mining, barmining, coast-mining, and any other similar operations now carried on by means of coffer-dams or dredging machines. The simple and effective method to which I refer is the invention of General Roy Stone, formerly an officer of volunteers, and at present a civil engineer, engaged under General Newton, of the United States Engineer Corps, upon the government works in New York harbor. General Stone has been, since September, 1878, in charge of operations upon Diamond Reef. This reef, lying between Governor's Island and the Battery, is one of the most dangerous in the harbor. Its position in the highway of navigation, and the fact that it is dangerous only to vessels of considerable draught and at certain stages of the tide, combine to increase the serious nature of the disasters which it has caused. The reef consists partly of rock in place, and partly of deposits of glacial clay, boulders, and pebbles, over all of which lies, or did lie until it was removed, the ordinary silt and rubbish of the harbor. As the purpose of the present paper has nothing to do with the special dimensions and other circamstances of this particular work, I describe those features only which are connected with General Stone's ingenious device. Various attempts have been made to remove the upper portion of Diamond Reef and secure a navigable depth at low tide. Some years ago Maillefert undertook to accomplish this by firing charges of high explosives, simply laid upon the surface. He accomplished some good in the removal of projecting points and ridges; but as soon as the surface of the reef had become approximately level, his method was no longer effective. After the work had been taken up by the Engineer Corps, the well-known drilling-scow invented by General Newton was brought into action; and, SO long as holes could be bored and fired in solid rock, this process was effective enough. In the mixture of hard-pan

Jan 1, 1880