Search Documents

The development of Western Mining Corporation's first commercial gold heap leaching operation is described. The laboratory testwork requirements for determining the amenability of ore to heap leaching techniques is discussed. Heap construction and operating practices are described; and production statistics and operating parameters are presented. It is shown that for a specific low grade gold ore a treatment cost optimization can be performed. Taking cognizance of the ore grade, percentage gold recovery, operating costs, and the gold sale price, it can be determined whether Carbon-In-Pulp (C-I-P) or Heap Leaching should be employed as the extraction process. The examples presented in this paper refer specifically to Kambalda and should not be used in themselves as generalities.

Jan 1, 1987

By A Crosky, S Saydam, H Chen, H L. Ramandi

Cable bolts and rock bolts are used as primary and secondary anchoring systems in many underground mines. Reports on the premature failure of cable bolts and rock bolts due to stress corrosion cracking (SCC) in underground coalmines have been increasing in the past two decades. The previous studies found that the SCC in both rock bolts and cable bolts occur as a consequence of atomic hydrogen diffusion into the material, which is known as hydrogen-induced stress corrosion cracking, HISCC (Craig et al, 2016; Wu et al, 2018b). While research to understand the process of SCC occurrence in underground mines is still required, finding a prevention solution to protect the bolts from HISCC is crucial. In this study, we analyse a variety of commercially available coatings for steel corrosion prevention, including barrier coating (ie epoxy, polyester TGIC) and sacrificial coating (hot-dip galvanising). We test the coating on coupons manufactured from rock bolts and cable bolts used in the coal mining industry.

Nov 29, 2022

By R C. Owen, M A. Ward

The paper describes the application of New Zealand's environmental impact assessment procedures to a proposed gold and silver mine in the North Island of New Zealand. The project is described and a summary is provided of the statutory permits or consents that are required prior to operation of the project. Emphasis is given to the requirement for environmental impact assessment and the preparation of a formal environmental impact report. The company's approach to impact assessment is described, with examples of how this assessment and the identification of management alternatives influenced the engineering design of the project. This paper was prepared as a contribution to a working session of the International Association of Impact Assessment VII Annual Conference, July 1988.

Jan 1, 1988

By Crawford G. R, Wold M. B

The application of the hydraulic fracturing technique to the measurement of in situ rock stress from underground excavation is discussed; including relevant theoretical considerations, equipmenl details, experimental technique and analysis procedures. Examples of the application of the technique at three Australian coal and metalliferous mining operations are given. The results obtained from these applications are compared with corresponding results obtained from overcoring tests conducted in close proximity at each site. Generally good correspondence in a wide variety of rock types is indicated. Experience gained with hydraulic fracturing at several underground mining sites has indicated it to be a quick, cost effective means of gaining an understanding of the in situ stress field in sufficient detail for many mine planning functions.

Jan 1, 1990

By McGill RA

The Ranger Uranium Mine is surrounded by a World Heritage National Park. The strict environmental controls under which the mine operates are based on scientific and social requirements. Release of non-process storm runoff water to the Magela Creek during flood discharge and under controlled conditions has been identified as Best Practicable Technology for the operation of the water management system. Social and political factors have limited this release to a wet season with an Annual Exceedance Probability of one in ten. The first-generation trigger mechanism was based on a percentile analysis of monthly rainfall. The second-generation trigger is based on cumulative monthly volume increase in the retention ponds and is considered to be more applicable to the operation of the mine water management system.

Jan 1, 1988

By M Aros, L Reilly

Iron ore is normally sold in bulk at certain specifications. These include iron grade and specific contaminant grades, typically silica, alumina, phosphorous and sulfur. These target grades are normally agreed between the mining company (producer) and the steelmaking company (customer).This study presents an alternative to traditional cut-off grade calculation, using linear programming that maximises the total ore inventories within a predefined mining envelope while meeting the specified targets. Providing a feasible mining sequence that maintains the target grade is not covered in this study.The method was applied to Fortescue’s operations. The complexity arising from differing ore quality within each mining horizon, variable yields and upgrades and the need to control iron and contaminant grades provided a good opportunity to test an alternative method of ore selection. The new method significantly reduced the time spent in cut-off selection and sensitivity analysis, and provided an optimised solution.CITATION:Aros, M and Reilly, L, 2014. Ore selection optimisation for an iron ore deposit using linear programming, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 345–350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

Over the last 100 years in the Polish mining industry considerable work has been done to assess optimum slurry, develop flexible delivery systems and adjust the fill technology to a wide variety of mining and geological conditions. Sand or industrial mineral waste materials for the backfilling of underground voids are used to control ground movement and surface deformation. This paper discusses various criteria to be considered in the preparation of a fill, including slurry properties, mine infrastructure, mining geometry, placement methods and the purpose of the backfill. This paper presents laboratory and in situ test data on the influence of materials parameters on the slurry flow in a pipeline system, stiffness, permeability, binding time and strength of a backfill, on the distribution of mixture in underground voids or the penetration between roof fall materials.

Jan 1, 1998

What is the best circuit to comminute primary crusher product to make beneficiation feed? Finding the best circuit to crush and grind minerals to beneficiation sizes is a complex problem that can lead to interminable discussion. Conclusions reached can be questioned. This will continue as long as the technology of comminution continues to expand, and is a mixture of many technical and economic factors in what is not a precise science. Laboratory and pilot plant procedures now exist that can help process engineers make sound decisions on which circuits are the best for crushing and grinding the specific ore being studied. It is the aim of this paper to discuss such procedures so a better under- standing of key decision parameters is avail- able, and to update comminution testing which has seen a. period of change in which new procedures have been introduced.

Jan 1, 1978

The Greymouth Coal field is situated on the West Coast of New Zealand's South Island and has been mined for coal for more than 120 years. The area covered in this paper is within the Rapahoe Sector of this field and contains >200 million tonnes of low ash, low sulphur, bituminous rank coal. Paper No 6, presented to the 19th Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy in Christchurch in August 1985 by R G Bowman, explained 'A Geologist's View' of the 'Economic Potential of the Greymouth Coalfield', and describes previous geological assessments of the Rapahoe Sector.

Jan 1, 1989

A philosophy is presented that new graduates in mining and metallurgy should be equipped to use computers during their under- graduate courses, should be aware of the capabilities and costs of a wide range of computing equipment, and should receive sufficient stimulus to become involved in applying computers for the benefit of the mineral industry. A program is presented in which computer applications and "hands on" involvement with computers are integrated into the progressive stages of the undergraduate courses in Mining and Metallurgy. In this respect, the role of the computer is to assist the student by performing time consuming tasks, to demonstrate the industrial applications of computing, to extend the scope and complexity of the tutorial, assignment and project work which can be undertaken by the student, and to provide the essential first stepping stones toward continued useful involvement with computers during the graduate's working life.

Jan 1, 1977

By White A, Price G

The main assets of a mining company are its orebodies; the second are the people who find and use them.The graphs in Figure 1 were derived from a paper by Rob Macdonald of Rothschild Australia presented to The AusIMM Centenary Conference in Adelaide earlier this year. They show that the value of the industry on the Australian Stock Exchange halved over the past decade, despite the re-investment of capital equivalent to its full market capitalisation. Why is this so? The average dividend yields for the ASX Mining Index was never above five per cent during that period and barely averaged 2.5 per cent. Why then is $Ai million capital re-investment per employee since 1960 not enough to generate a rate of return to investors better than lousy bank interest? Do the investing public no longer regard our industry's assets to be world class?

Jan 1, 1993

By Bain J. H

Since zinc was first deposited at Risdon in February, 1917, provision of the most economical cathode assembly has been a subject of extensive research, the major problems being corrosion and efficient use of power.From the corrosion viewpoint, a perfect cathode is one in which the life of the headbar and the deposition sheet are the same. However, corrosion usually concentrates in a narrow zone across the face- of the sheet, resulting in breakages which, before the advent of argon arc welding, meant a loss of a 'complete assembly.Attempts to extend sheet life included use of thicker sheets, multitudinous protective coatings applied with varying degrees of success, re-rolling, and for a time, aluminium consumption was reduced when broken sheets found re-use as protecting strips. This latter economy became impracticable when electrode spacing was reduced for greater efficiency in power utilization.As an integral part of the electrode, the headbar was modified accordingly. Copper headbars, although more corrosion resistant, were replaced by aluminium due to a possibility of dissolved, copper promoting deterioration.Thicker electrodes and regulated spacing reduced internal shorting, whilst provision of knife-edge type supports on both contact and insulator ends of headbars aided in electrode centralising and continuous electrical conduction.After much experimeIitation, an assembly has been evolved which, with the aid of argon arc welding and tbe use of minimum additional aluminium, permits comparable headbar and sheet lives, combined with good electrical conduction throughout the life of the cathode.INTRODUCTION Over 300 tons of zinc are produced daily at Risdon from a purified zinc sulphate solution by electrolysis, the zinc being deposited upon all-aluminium (except for copper contact) cathodes. It is stripped in 72-hour cycles from the cathodes, melted and cast into the customary rectangular slabs.

Jan 1, 1958

By Kubik K

The objective of this paper was to determine if recent advances in numerical electromagnetic wave propagation modelling techniques could be used to study the propagation of GPS signals over arbitrary terrain. Specifically the effects of diffraction and multipath were to be modelled accurately for propagation over arbitrary terrain surfaces defined by a digital terrain model. Ideally the model was to be in three dimensions and cover an area of a few square kilometres with a simulation height of a few hundred metres. Simulations were to run on current technology PC's with run times less than a few hours. A relatively new technique that involves a numerical solution to the Parabolic Equations can be used to solve for two-dimensional propagation over any type of terrain. The PE provides a direct solution of Maxwell's wave equations by approximating the Helmholtz scalar wave equation. This technique does not rely on the study of individual ray paths as used in the Geometrical Theory of Diffraction (GTD). It was decided to develop a two dimensional Parabolic Equation code, using the Fourier Split/Step method that allowed propagation over arbitrary terrain (; ; ). The model boundary conditions assumed that the satellite transmission was a plane wave, and that the lower boundary was a perfect reflector. Propagation simulations from the model accurately provide the amplitude and phase of the propagated plane wave at all points within the model domain. The PE model was used to study the effects of diffraction and multipath caused by various types of terrain commonly found in an open cut mining environment. The study of diffraction errors was relatively simple, because we are simply concerned with amplitude of the signal as it diffracts about an obstacle. If the amplitude is above the level receivable by a GPS receiver then the diffraction error can be obtained from the geometry of the terrain obstacle. The study of multipath is more complex, as the computed phase from the PE model is ambiguous and the presence of multipath can only be inferred. Thus the absolute magnitude of the nmltipath error is not currently determinable, though the results of some new work is shown here. This paper shows that diffraction effects can cause significant errors in range. It also shows the effects that multipath has on the received amplitude of the signal and the received phase of the signal. A discussion is made of further work that is presently underway that will allow the direct determination of the multipath error by comparing the ambiguous phase with a reference phase.

Jan 1, 1997

The Framework Convention on Climate Change (FCCC) places serious obligations on New Zealand as a signatory nation. This paper examines the nature of the FCCC, New Zealand 's proposed policy response, and the.implications for the minerals industry.

Jan 1, 1994

During the century past geologists have discovered an extraordinary range of mineral resources. It is somewhat surprising, in view of their success, to look back and find that geologists have been concerned through the entire time about the adequacy of resources to meet future needs. They continue to express concern. The basis of their concerns seems to rest as much in social issue as in evaluations of geology.Demand for mineral resources is driven by population and by per capita consumption. Both have grown steadily over the past century, and both continue to rise. In 1890 the global population was about 1.7 billion, people. It has now exceeded 5 billion and the growth rate is such that by the year 2000, the global population will be between 6~ and 7 billion. Demographic projections suggest the global population will approach 12 billion before a steady state is reached dnrino the centiirv ahead

Jan 1, 1990

By Li N, Grimsey E. J

A technique has been developed for the fast measurement of the liquidus temperature of molten salt systems. The method employs a type K thermocouple embedded within the centre of a copper cylinder. The cylinder is immersed into the molten salt bath and the resultant heating curve is recorded using a PC-based data logging system. Upon immersion of the cylinder into the bath, a layer of salt freezes from the melt onto the surface. When this layer remelts during heating, the shape of the heating curve exhibits a change. The onset of this change can be detected by numerical differentiation of the heating curve, and the temperature at the onset represents an estimate of the liquidus of the melt. This work describes the technique and its application to the measurement of liquidus temperatures of MgC12 - NaCl and BaC12 - NaCl salt mixtures, in addition to a number of solidus temperatures.

Jan 1, 1996

The sampling of a run-of-mine (ROM) ore with the objective of controlling the fundamental variance associated with the sampling step is a poorly understood subject. Finding the effective sampling constant by repetitive sampling to establish the variance between nominally identical subsamples of a given mass of the ore is a laborious, time-consuming and very expensive exercise. In this paper, the run-of-mine ore is modelled using three components: ore, waste, and relatively fine material which shows significant liberation of the mineral phase(s) carrying the target analyte. The expression for the sampling constant of the mixture is developed from first principles. The form of the equation provides insight into the factors that are important in controlling the magnitude of the sampling constant and hence the fundamental uncertainty associated with a given mass of sample. The controlling factors are shown to be the size distribution of the ore/waste mixture, the proportion of waste mixed with the ore and the extent of liberation and the size distribution of the liberated material in the finer fractions.

Jan 1, 2008

By G P. F Chitombo

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have been identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

By Sturgul J. R

The South Middleback Ranges (SMR) operation involves the develop- ment of iron ore resources at the Iron Duke mine in the South Middle- back Ranges to replace the Iron Baron mine whose reserves are nearing depletion. The Iron Duke mine will be developed by contract to the stage where it can continue operation at full production when Iron Baron is closed. As part of the mine planning of the operation a GPSS computer simulation model was written to determine equipment requirements. The model simulated the operation of the mine with trucks transporting ore and waste to the appropriate destinations and producing a blended product in the stockpiles. A loader and two trucks would transport ore from the stockpiles to the crusher for one shift per day. The simulation shut the operation down at crib, morning tea, shift change and weekends, and also on the third shift each day. It also modelled operating delays. The results gave equipment operating hours and total output of each material type. The model was modified to produce different outputs from the mine and could be used to determine the most productive shift arrangement.

Jan 1, 1989

By J St George

Much of AucklandÆs transport infrastructure has been developed on surface with little or no consideration of underground options. Current and planned transportation routes are now facing high costs due to land values and increasing environmental resistance to surface development. The option of utilising underground space becomes a feasible investment decision for these links as well as being the only option to develop the rail network within the inner city area. Transportation tunnels offer a quieter, more energy efficient means of getting around with minimal impacts on the surface environment. One of the major impediments to tunnelling is the high construction cost, which is partly related to the risks of encountering unexpected ground conditions and/or the possibility of causing surface ground deformations which could damage structures. The geology of Auckland has had substantial investigation through various studies and projects. The sediments of the East Coast Bays Formation (ECBF) underlie most of the Auckland urban area. It is classified as a soft rock and is a suitable material to tunnel through using either a tunnel boring machine or a roadheader. This paper reviews the limited amount of tunnelling completed in the urban Auckland area, together with the international advancements that have been made in the tunnelling industry. From the known features of the local geology and the problems encountered historically, the likely risks of tunnelling in Auckland are presented and ways in which those risks could be reduced and managed, are discussed. In addition, contractual arrangements between client and contractor are assessed with respect to complicated projects (such as tunnelling), so that the risks can be managed to create efficient infrastructure routes with reduced costs.

Jan 1, 2008