Search Documents

Despite the large areas of sedimentary basins in Western Australia, the coal resources are very meagre., This is a serious problem for the State, which-at present-lacks any other alternate source of fuel-for power production.. Located coal deposits are all poor in quality and mostly brown coals of little importance. The best..coal suitable for extraction is at Collie, where a black=sub- bituminous non-coking coal is mined. Most other coals recorded are low grade or lignite, with high ash'and moisture content and a low calorific value. Coal was first discovered in Western Australia in the bed of the Irwin River, 50-miles south-east of Geraldton, by the Gregory brothers, explorers, in the year 18+6,. but although investigated, it has never been developed. The most noteworthy discovery of coal was in the Collie River, 26 miles east of Bunbury, by Arthur Perrin in 1883. Production commenced in 1898 and ever since, Collie has continued to be the State's sole producing coalfield.

Jan 1, 1964

For many crushed aggregate producers will the finest fraction minus 4 mm represent a problem. The fine material will fetch a much lower price than the coarser products, and may even be difficult to sell in some markets. The blasting operation will strongly influence the generation of fines after both blasting and crushing. Drill hole deviation together with the drill hole diameter, powder factor and velocity of detonation are the most important blasting parameters with regard to the generation of fines. Drill hole deviation is often ignored, and many operators will just reduce the drilling pattern in order to avoid hard bottom and an excessive number of boulders. The paper presents a technical and economic analysis of how drill hole deviation will lead to an increased generation of fines in crushed aggregate production. The analysis shows that the loss of sales revenues will be much higher than the extra costs for drilling and blasting caused by compensating for drill hole deviation by putting in more holes.

Jan 1, 1999

By A Quigley

The Northside Storage Tunnel Project in Sydney includes over 20 km of TBM driven tunnels, over 3 km of declines and major caverns and pump rooms. The paper describes methods used for design on the project. Emphasis is given to the refinement of the use of empirical rock mass classifications, and to the use of discontinuum numerical methods.The use of empirical rock mass classifications in Sydney sandstone has usually led to conservative design because the systems are based on a random orientation of joints in the rockmass. Because the joint sets are usually oriented in a way that is beneficial for tunnelling, limits must be placed on the parameters used in the classifications system. The paper discusses these limits and the derivation of the parameters.The use of numerical methods in Sydney sandstone is discussed. Continuum methods have their uses, but discontinuum methods are preferred. The use of UDEC has been validated against a previous project, the New Southern Railway. Recommendations are given for UDEC models.

Jan 1, 1999

The past year has been a difficult one for the mining industry in this country, but an active and successful one for the Branch. Membership has continued to increase, albeit at a slower rate than last year, and with the increase almost all from student membership. I dwelt at some length last year on the continued increase in student membership, which I ascribed largely to deliberate policies adopted by the Branch to foster this area of membership. I don't propose to reiterate these, suffice it to say that as usual, the Otago School of Mines has been a prolific source of student members, and it will be a pity if this source dries up û more on this subject later. In fact, students form just on 29 per cent of the Branch's total membership û a far higher percentage than for any other Branch in the Institute, whose membership as a whole comprises only ten per cent students.

Jan 1, 1985

By Chapman RL

A new process has been developed to remove the impurities copper, cadmium, cobalt and nickel from a zinc plant electrolyte by cementation on zinc dust. The process has been tested in the laboratory and in a continuously operated pilot plant. It has been found that cadmium, in the presence of small amounts of antimony in solution, assists the removal of cobalt. Cementation is conducted in two stages: the first stage for removal of copper with a small excess of zinc dust to produce a relatively high grade product, the second stage for removal of cadmium, cobalt and nickel by addition of zinc dust in the presence of anti- mony. The excess zinc and the cadmium present in the second stage cementate can be selective- ly recovered by slow leaching in spent electrolyte. Zinc dust processes in use elsewhere are described and compared with the present system for use in the Risdon circuit.

Jan 1, 1984

Synthetic and commercial activated carbons are characterised for several chemical and physical properties. A range of techniques is used to establish correlations between physicochemical parameters and gold- adsorption activities. The most important parameter in the carbon activation process for a product with a high gold-adsorption activity is the activation temperature. High activation temperatures yield products with large micropore volumes which provides sites that are ideal in size for adsorption. The surface area of an activated carbon is not necessarily a good measure of its adsorption activity. Surface oxygen-containing functional groups are identified by Fourier transform infrared spectrophotometry to be comprised mainly of ethers and hydroxyls. These functional groups line the edges of the micropores imparting a polar character to the pore and aid in the solvation of the adsorbate. Oxidants such as nitric acid result in a proliferation of surface carboxyl groups. resulting in a negatively- charged surface that is not conducive to the adsorption of gold.

Jan 1, 1993

Geological models for the exploration and evaluation of epithermal Au and porphyry Cu-Au deposits rely upon a classification of different deposit styles and an understanding of the evolutionary processes of deposit formation. These models guide the interpretation of subsurface deposit anatomy in order to target drill testing and assist the explorationist to focus on the more prospective projects. It is important for the explorationist to distinguish between different styles of magmatic arc Au deposits as each style displays distinctive characteristics with exploration implications. Magmatic arc Au deposits are distinguished as porphyry Cu-Au formed at depths of 1 - 2 km at the apophysis to larger, buried, magmatic sources which are also the ultimate metal sources for the varying styles of shallower level epithermal Au deposits. Low sulfidation epithermal Au deposits characteristically develop from dilute circulating meteoric waters and are distinguished as the group with a closer relationship to intrusive source rocks, and slightly higher sulfide contents (still generally

Jan 1, 2004

By Mansor A. N

Results are reported for the computer simulation of heap leaching of mixed copper oxide and sulphide ores. They resemble those obtained from testwork in terms of a substantial peak in the copper concentration of the pregnant solution, an initial period when no copper emerges and a lengthy period towards the end when the copper concentration and the daily increment in copper recovery are low. The simulation can be used to forecast process results before any column or similar testwork is performed. Potential applications of the simulation to process design, operating strategy and optimisation are discussed. Three modes of operation are identified that correspond to different performance patterns and dependencies on ore and process variables. The relative merits of different operating strategies for approaching the ideal performance are being investigated. For process design and development purposes, the simulation may be used with a limited testwork programme to achieve significant savings in time and resources.

Jan 1, 1989

By Hall S. F, Quast K. B Newell R, Ketteridge I. B

For the past six years research funded by the State Energy Research Advisory Commit- tee of South Australia has been conducted at the South Australian Institute of Technology, School of Mining and Metallurgy on South Australian lignites. A major part of this work has been a study of the potential bene- fication of Bowmans lignite using hydrometal- lurgical techniques. The Bowmans lignite de- posit is the largest of its type in South Australia and is a major energy reserve for the state. The utilization potential of this deposit is reduced by its very high insitu NaCl content which presents serious problems for any process. Previous research conducted by Readett and co-workers (1984a & b) has shown that NaCl is amenable to extraction using simple batch water leaching operations. This leaching has been successfully described using a two stage diffusion model derived from first principles based on a simple diaphragm cell.

Jan 1, 1987

By Pollard D, Meadows N

The presence of impurities which are electropositive to zinc in acid zinc electrolyte causes changes to deposit morphology and reduced current efficiency. Glue may be added to control some impurity effects, but assaying for animal glue concentration is difficult and seldom done. Measurement of the activation overpotential for zinc deposition by cyclic voltammetry is used in some plants to monitor electrolyte quality and control glue additions.The deposit morphology and current efficiency of zinc deposition from commercial electrolyte were investigated for various glue additions in the presence of increased levels of antimony. Cyclic voltammetry was investigated as a method of optimising glue additions in the presence of antimony.Scanning electron rnicroscopy showed deposits characteristic of the impurity element present and the glue addition rate. Cyclic voltarnmetry measurements showed some correlation between current efficiency and activation polarisation potential. The importance of using tankhouse electrolytes where results are to be related to tankhouse operation was noted.

Jan 1, 1988

This paper presents a method for estimating the strength and stability of model coal pillars with bedding planes (weakness planes) inclination. The strength of coal relative to the angular difference between the principal stress direction and bedding planes is considered. The failure behaviour of model coal pillars containing weakness plane inclination by using servo-control Schenck Machine are shown. Uniaxial and triaxial compressive strength of coal specimens are investigated, and test results indicated that the strength of coal pillars depends on the weakness planes inclination with respect to the principal stress direction. However, it is shown that with increasing confining pressure, the effect of weakness planes inclination on the strength of the coal specimens is reduced. An empirical method is given for prediction the compressive strength of coal containing weakness planes inclination. The results of this method are compared with the experimental results and Jaeger theory. Finally, three well-known empirical strength criteria were tested against the triaxial test data for coal containing weakness planes inclination.

Jan 1, 1995

By Grimstone LR, Leach JHJ

An analytical technique is described to identify areas of structural disturbance to coal and interseam strata in coal measures. It is based on exploration borehole data which records seam intersections and interseam lithologies. Computerised data bases have been developed to allow processing of large quantities of borehole records. The case study discussed is located in a tectonic setting dominated by thrust faulting. It provides a mechanism for the identification of low angle and bedding plane faults. In addition it allows the preparation of plans showing the areal distribution of the thrust sheets in the statigraphic section throughout the mine prospect. The technique requires the identification of normal undisturbed depositional thickness of coal seams and interseams to be determined. This is done for coal by the identification of coal ply distribution over the area. For interseam lithologies it is based on sedimentological modelling of lithology distributions, related back to the original depositional environments. Variations from the expected values are interpreted as structural Deformations.

Jan 1, 1986

By Davies K. E

Several nuclear techniques have been assessed for application to online conveyor belt analysis of oil yield from Rundle oil shale. The most favourable technique is neutron inelastic scattering which determines the total carbon content of bulk shale samples. Correlations of chemical laboratory assays for 540 Rundle oil shale samples show that oil yield can be predicted from total carbon to within 11 litre/tonne.Laboratory experimental work on 17 bulk samples of Rundle oil shale indicated that carbon and oil yield can be determined to within 0.6 wt per cent and 9 litre/tonne, respectively, using the neutron inelastic scatter technique. A practical neutron inelastic scatter gauge for application on a 23 mm thick reinforced conveyor belt could consist of a 5 curie 241 Am-Be neutron source and a 150 mm diameter x 100 mm thick Nal(TI) detector. With this gauge, the analysis time to achieve a counting statistical error of 6 litre/tonne should be about five minutes.

Jan 1, 1985

By Bluck R. G

The Murray Basin is known to contain major deposits of heavy mineral sands and intensive exploration for new deposits is being conducted in Victoria, South Australia and New South Wales. The western Basin was well served in the Pliocene and Early Pleistocene by a variety of appropriate sediment sources, and potential coastal traps. Immature, fluvially-sourced sediments forming the Pliocene coastal complex of the Marmon-Jabuk Range in South Australia are part of a marginal marine assemblage containing a suite of economically important heavy minerals that include ihnenite, zircon, rutile and tourmaline. From a consideration of Pliocene palaeogeography and coastal dynamics, specific targets where concentrating processes are likely to have operated are identified in the South Australian portion of the Murray Basin. Such palaeo-environments include the down-drift, littoral zone of discrete foredunes or coastal barriers, the source area for transgressive dune complexes, tombolo facies, and intertidal shoals and sandbanks. Similar coastal processes are recognised for a preserved Early Pleistocene barrier complex.

Jan 1, 1990

By Dhawan AK

On 8 July 1993, a landslide of about one million cubic metres of rock blocked the river Satluj near Sanjay Vidyut Pariyojana - Bhaba project and caused flooding into the Bhaba Power House (120 MW) resulting in suspension of power generation. The concerned authorities desired an early removal of the blockade by an underwater blasting operation into the over topping water to reduce the water level at the blockade and resume power generation in the power house. In the absence of underwater drilling, it was essential for the blasting technique to be used where no cavity to confine the explosive was required. For this reason mud capping and plaster shooting with directional throw were used and additional specially fabricated mild steel pipe charges were used under high current for an underwater trenching operation. By employing these techniques the river blockade was removed up to the required depth and on 8 September 1993 the Power House resumed the power generation.

Jan 1, 1995

By Ishikawa K, Kikuchi T, Tokairin Y

Roadheader, developed from coal cutting machines, is generally classified as a tunnel excavation machine for soft rocks in respect to excavation mechanism, machine structure, weight, engine output and so on. In recent tunnel works, however, there is an increasing demand for changing from blasting to mechanical excavation by roadheaders to avoid environmental problems such as noise and vibration. But there exist various difficulties in excavation of harder rocks by roadheaders. In order to explore the possibilities of roadheader excavation, we performed field and laboratory experiments. In the field experiment, roadheader model S-125 (Mitui Miike Machinery Co.,Ltd.) was tested for various rocks of wide range of hardness, and excavation capacity and wear of picks were measured. In the laboratory test, cutting performance of the picks was tested by our cutter testing machine. This report describes thr: of these experiments and discussions :n possibility of applying boom-type tunnelling machines to hard rock excavation based on these experimental data.

Jan 1, 1987

By Newell R

The situation in which a gas stream flows through a bed of solids is found in many extractive metallurgy operations. Examples include blast furnace smelting, sintering and pellet firing. In such cases the resistance of the bed to fluid flow and heat transfer is of major significance to the operation of the process. This depends on the structure of the bed, which in turn is influenced by the manner in which the materials are charged to the bed. In this work, packed beds of hematite pellets of two different sizes were prepared in which the pellets were charged as a uniform mixture and in layers. The porosity, flow resistance and heat front velocity were measured and compared for the different bed configurations. For layered beds, the overall porosity and heat front velocity increased while the flow resistance decreased when compared with the values obtained for the uniform mixture. The size of the layers also had an effect on flow Properties.

Jan 1, 1991

By Sakurai F

Akita Zinc Refinery of Mitsubishi Metal Corporation (MMC) started operation in 1953 with a capacity of 560 tons of electrolytic zinc per month. Its capacity has been expanded gradually and reached 8,100 tons per month in 1973. However, present production level is about 6,500 tons per month due to the depressed zinc market. In 1963, newly developed sulphate roasting was incorporated for residue treatment. Since 1973, electric power from Ohnuma geothermal power station of MMC has been supplied in addition to hydroelectric power from Komata power station of MMC. At present, about 40% of power is supplied from our company's power station and the rest is from the power company. Recent customers' demands for zinc prod- ucts include various kinds of shape, weight and chemical composition of galvanizing zinc alloy. It is necessary for zinc producer not only to meet the requirements of customers but also to enhance the value of zinc product in order to expand the market of zinc.

Jan 1, 1987

By Kaleta S, McTavish LP, Turner RD

Primary production blasting at Hamers- ley Iron began with seven inch holes at Tom Price in 1966 and has developed since then to large multiple row shots of 381 mm holes at Tom Price and 311 mm at Paraburdoo. Up to 1.3 million tonnes are initiated in a single blast with the average around 300,000 tonnes. Development can be traced through Anfo, AlAnfo, slurries, various boosters, initiation and delay techniques, hole loading and daily operating practices. A standard practice could be developed for the two mines for normal pro- duction blasts; this would not apply to such common variations as low "paddy" shots, pre- splitting, tight corners necessitating single row drilling etc. Because of ground variation three or even four sizes of drill holes may well be economic- al for blasting, even though this would be off set by complications in operation, supervision, store stocking and maintenance, particularly in Drilling.

Jan 1, 1978

By Peck WH

For many years it was realised that the methods used for unloading concentrates at Port Pirie were inefficient and labour intensive, therefore, when a decision was reached to standardise the east-west rail link from Sydney to Perth, the opportunity was taken to consider entirely new schemes for the handling of concentrates at Broken Hill and Port Pirie. After considerable testing and investigation, it was decided to install a completely new concentrates handling plant incorporating a tippler at Port Pirieòto replace the previous long established methods of unloading and dis- tributing concentrates to the operating plant.and the shipping berths. To achieve this, wagons of concentrates from the various mines are marshalled in a set order at Broken Hill and conveyed to Port Pirie in 56-wagon trains. On arrival at Port Pirie, the wagons are checked and moved to a position where they come under the control of the automatic wagon marshalling equipment.

Jan 1, 1975