Search Documents

By S Nie, I Bergqvist, F Ouchterlony

In blasting, a few or many cracks are driven from the borehole into the rock. But what causes the cracks? The most common theory of breakage consists of two stages; first the shock wave causes radial cracks to form around the hole then the gases penetrate into the cracks, and widen them and make them longer. Another theory presented by Brinkmann suggests that the back damage is primarily controlled by shock and that the gas penetration is the mechanism controlling breakout of the burden. He did his experimental work using blasthole liners. Recent research at SveBeFo has examined this matter further. In a quarry a number of benching holes have been blasted simultaneously. In some of these holes tubular Swellex bolts were inflated and decoupled charges put inside the tubes without stemming. Other holes were identically charged but without the lining. Finally some holes were also stemmed. After blasting the cracks in the remaining rock were studied. There was no difference in crack lengths between holes charged normally (no stemming) and holes where the charges were inside the bolts. On the other hand when stemming was used, the crack lengths increased for some explosives but remained the same for an emulsion explosive. In another set up blasted granite blocks were charged in the same way as above. Then we could also measure the bore hole pressure. The pressure gauge consists of a small carbon resistor inside a steel cylinder. It is called LHM (Location-fixed Hydrodynamic Measuring Cup) and is placed at the bottom of the hole. A smaller exit hole from the bottom is drilled for the cables. The paper presents the technique and the results obtained from both the quarry blasting and the blasting of the blocks.

Jan 1, 2001

By K Esmaeili, S Aziznejad

Impact-induced rock fragmentation is a mechanism that is commonly used for rock breakage in drilling and crushing. Additionally, rock fragmentation by blasting is frequently used in rock excavation operations. Experience shows that the presence of discontinuities can significantly influence the impact-induced damage and fragmentation of rock. Quantification of the response of jointed rock masses to impact loads is complicated by the fact that the available laboratory tests are mainly designed for aggregates or intact rocks. It can be argued that neither of these tests adequately represent a jointed rock mass. This paper presents the results of a series of numerical simulations used to investigate the influence of pre-existing discontinuities on the impact-induced fragmentation of rock masses. The methodology includes determination of the static and dynamic mechanical properties of a rock unit by conducting a series of laboratory tests on intact rock samples collected from a quarry in Canada. A 2D distinct element code, Particle Flow Code, was used to generate a bonded particle model in order to simulate both static mechanical properties (uniaxial compressive strength, elastic modulus, Poisson’s ratio and indirect tensile strength) and dynamic mechanical property (drop weight tensile strength) of the intact rock. The calibrated numerical model was then used to construct large-scale synthetic rock mass samples by incorporating discontinuity networks of different intensity into the bonded particle model. Finally, the impact-induced fragmentation inflicted by a rigid projectile particle on the jointed rock mass samples, simulated by a synthetic rock mass model, was determined. More fragmentation was observed for the rock mass samples with higher joint intensity.CITATION:Aziznejad, S and Esmaeili, K, 2015. Effects of joint intensity on rock fragmentation by impact, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M I. Pownceby, N A. S Webster, J R. Manuel, J M. F Clout, E Donskoi, N A. Ware

The relative influences of sinter mineralogy, sintering temperature, solid and pore macro- and microstructure on iron ore sinter physical strength are not yet fully understood. Whilst a range of analysis techniques have been used by researchers to evaluate sinter physical properties and sinter mineralogy, none have been able to directly link sinter mineralogy and physical strength under controlled conditions. CSIRO has developed a unique laboratory method to study the fundamental melting properties of fine iron ores in a laboratory furnace under a controlled temperature and gas atmosphere environment designed to simulate the industrial sintering process. Compacted tablet samples for a 0.41 per cent and a 2.5 per cent Al2O3 series were fired in a tube furnace at various temperatures, cooled, then tumbled using a modified Bond abrasion test apparatus to determine a relative tumble index (TI) at each temperature. Quantitative XRD (QXRD) analysis was then carried out on the tumbled samples and optical image analysis (OIA) was conducted on polished sections of a separately fired compact in each case. The amount of total SFCA was found to decrease with increasing firing temperature for both alumina series with the total amount of SFCA higher in the 2.5 per cent Al2O3 series compared to 0.41 per cent Al2O3 series samples. The increase in the amount of magnetite and hematite with increasing firing temperature was largely at the expense of a decrease in total SFCA. Overall, there was good agreement between the quantitative mineralogy determined from QXRD versus OIA for SFCA, hematite and magnetite. Qualitative analysis of high magnification images of the sinter correlated with both the OIA and QXRD results.

Sep 18, 2023

By White A. H, Gillies A. D S

In recent years the Australian gold industry has gone through a major expansion phase. The need for finance has led to adoption of different approaches such as the well known gold loan, forward selling, equity participation by suppliers and equipment leasing. During early periods of the expansion, significant new equity was raised chiefly for high risk exploration ventures. The major form of new equity finance was ordinary shares, often in 'No Liability' companies. The increasing capital requirement of the huge new development projects of the 1980s also spurred the use of debt finance. This trend was accelerated as high inflation and the taxation advantages of debt finance made borrowing attractive. This paper reviews major financing techniques used by the Australian gold industry with particular emphasis on the innovative financing techniques initiated recently. An analysis has been undertaken of the effects on the industry of issues such gold loans, forward selling, equity participation by suppliers, fly-in fly-out operations, contractor mining and equipment leasing. In order to achieve a better understanding of the innovative financing techniques, a survey of already published financial data from well known Australian gold mines was carried out. Data was collected from various published financial reports of gold mining companies. In addition, a questionnaire survey was sent to gold mining companies to assist the collection of further information. The results of this study show that there are a significant number of gold mines variously using gold loans, forward sales, contractor mining and fly-in and fly-out arrangements to finance their projects. Only four operations have vendor suppliers investing capital funds in their projects. Based on the findings of this study, conclusions and recommendations are drawn that these approaches are likely to be with Australian gold industry for some time in the future and will continue to be intensively applied to finance gold projects.

Jan 1, 1994

By J Boshoff, D Reid

It has been recognised worldwide that the liquefaction risk of unconstrained tailings stacks or cyclone underflow embankments requires careful consideration. The stability of a tailings deposit where the perimeter embankments are made up of hydraulic fill is often governed by post-liquefaction stability.Cyclones are frequently used around the world to classify tailings into a coarse underflow for building a tailings impoundment wall and a finer fraction that is disposed of into the basin. The shear strength of the tailings that form the outer embankment of a tailings storage facility (TSF) and the location of the phreatic surface are the two most significant factors influencing the structural integrity of the facility. The coarse underflow is placed in such a way as to contain the overflow, which is finer, has low strength and is often poorly consolidated.A cyclone field trial was undertaken at a gold mine in Western Australia to assess the feasibility of using the cyclone deposition method to optimise and increase the capacity of an existing tailings cell. The aim of the cyclone trial was to collect information to demonstrate to the client and the regulators that cyclone deposition was a feasible option for raising TSF embankments. The cyclone trial provided an opportunity to assess the cyclone under field conditions and the quantity and quality of the underflow fraction produced on-site. A variety of methods were used to assess the flow liquefaction susceptibility of the tailings underflow sample produced during the cyclone field trial.The field trial, laboratory testing and analysis will be discussed in this paper.CITATION:Boshoff, J and Reid, D, 2015. The resistance of cyclone underflow material to flow liquefaction, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 151–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By G Balog, T Ormerod, D Sidea

Carrapateena is a copper-gold sub level caving operation located in the Gawler Craton, South Australia. One of Australia’s largest undeveloped copper deposits, the project will be a 4.25 Mtpa underground operation, with an estimated mine life of 20 years (OZ Minerals, 2017). First concentrate production was achieved in December 2019, within the Iron Ore Copper Gold (IOCG) hematite breccia complex. The Carrapateena orebody is overlain by 500 m of barren sediments of the Stuart Shelf, which hosts two aquifers. The cover sequence is dominated by shales, quartzites and sandstones in order of thickness. The cover sequence presented challenges to the mine ventilation system as a result of highly variable rock strengths. On this basis, the site developed the first vent rise, Vent Rise 5 (VR5), earlier than required as a means to test the empirical stability assessment. Assessment for VR5 was completed in 2017, with the mine yet to develop through much of the cover sequence. Due to the geotechnical data available at the time, it was anticipated that break out would occur within the vent rise walls as a function of the low strength Woomera shales. VR5 was developed to 4.5 mᴓ in late 2018. The timing of the VR5 development enabled the site technical team to calibrate empirical stability factors for the assessment of future vent rises. At the time of writing, four additional vent rises have been successfully developed to a diameter of 5.5 m. No significant overbreak has been observed within any of the vent rises. This paper is intended for geotechnical practitioners designing large-diameter vent rises in geological environments similar to the Stuart Shelf where a similar approach to vent rise design may be warranted.

Mar 15, 2021

By J Krnmmelbein, T Raab

In Lusatia, lignite mining causes major disturbances on the landscape scale. Reclamation procedures are applied to recover the reconstructed landscape for different land use options. In this study we investigate soil physical properties of an agricultural reclamation/recultivation site directly after site restoration and the development of selected parameters within the first years after site restoration depending on varying recultivation strategies.The sandy substrates used for recultivation stem from depths of several meters. They are unstructured, free of recent organic matter and have high contents of calcium carbonate. During reconstruction and most of all during surface levelling with heavy crawlers, the substrate?undergoes high mechanical stresses. This leads to partly severe soil or substrate compaction, depending amongst others on substrate water content and mechanical stresses during site construction. We investigate the effect of different organic soil amendments, different crop rotations and partly subsoiling on the development of soil structure. We compare results of laboratory measurements directly after site construction before any reclamation measures had been applied to results we gained after three and four years of recultivation. The results show that after the earthworks are completed, the site is strongly heterogeneous in relation to mechanical stability, permeability for air and water, pore volume and bulk density. The results after three and four years show that the heterogeneity of soil physical parameters decreases. The selection of suitable crop rotations superimposes the affects of other reclamation measures, eg varying organic fertilisers or deep loosening.CITATION:Krnmmelbein, J and Raab, T, 2012. Reclaimed lignite mining areas A73 in Lusatia - Development of soil physical parameters of an agricultural site within the first years after site reconstruction, in Proceedings Life-of-Mine 2012 , pp 117-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By P B. Hills

A simple algebraic method of aligning large scale underground excavations such as a crusher station or workshop or indeed any large cavern or mine layout to the optimal stress condition is outlined. The method uses the stress transformation law to determine how the component stresses vary as the stress tensor is rotated around its axis. The aim is to define the orientations at which the maximum and minimum horizontal stresses occur such that the excavation can be aligned with its long axis paralleling the trend of the maximum horizontal stress leading to the minimum potential for overstressing of the side walls. The physical environment in which the stress field is acting is unchanged. At the design location, the trend and plunge of the major principal stress is unchanged. However, the coordinate system by which the location of the stress field is described is arbitrary and the stress transformation law allows that coordinate system to be rotated to a more convenient orientation and for the component stresses to be calculated within the alterative coordinate system. The stress field is typically described in terms of normal and shear stresses aligned to a north–south, east–west, vertical, coordinate system. In this scenario, there are two orientations in the 360° horizontal plane defined by the coordinate system where the horizontal normal stresses are equal, and at 45° to those orientations, two orientations where they diverge to the maximum extent. Those orientations of maximum divergence correspond to the trend of the maximum and minimum horizontal stresses, usually designated σH and σh, and that is what the algebraic manipulation seeks to determine. This technique is a first pass assessment which relies on a knowledge of the full stress tensor. It is not a replacement for numerical modelling or detailed design, but a tool to guide planning.

Nov 29, 2022

By M R. Lane, M L. Cramer, N P. Wines

Increasing attention is being focused by regulators and industry on the residual environmental liabilities associated with mining projects following site relinquishment (termed surrender in Queensland). Even sites that have been rehabilitated to a high standard and to the satisfaction of the regulator are not completely risk free and may require some degree of ongoing management. As well as ongoing monitoring and maintenance costs, considerations should include how costs associated with potential risk event occurrence can be quantified and, if considered material, how provisioning should be undertaken to minimise the risk to the state and to taxpayers. In Queensland for example, once a resource site is fully rehabilitated and meets its environmental authority conditions or rehabilitation completion criteria, the tenure and environmental authority can be surrendered. During the surrender process any ‘residual risks’ resulting from the use of the site for the resource activity must be considered, and, if requested, a payment given to the government to cover any ongoing management and risk costs. Accent Environmental, in conjunction with Lane Associates, was engaged by the Queensland Government as part of the government’s financial assurance framework reforms to develop an innovative, ‘one-size fits most’ Residual Risk Calculator for the Queensland resources industry. The calculator is an Excel-based tool that uses detailed user inputs to estimate post-surrender management requirements and liability at resource sites. If residual environmental risks associated with rehabilitated mine sites can be identified, quantified and managed through pragmatic regulatory tools and effective provisioning, site relinquishment/surrender can be achieved without compromising environmental and social outcomes or exposing the state to unreasonable financial risk. The effective management of residual risk can also help facilitate operations as well as relinquishment/surrender of sites where a ‘walkaway’ solution may not be otherwise technically feasible.

Aug 2, 2023

By F Sahlström, E M. Jolis, V R Troll, E Jonsson, K Högdahl, C Harris

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Bastnäs-type magnetite-skarn-hosted rare earth element (REE) mineralisations are located in the Palaeoproterozoic Bergslagen ore province, central Sweden, and occur along a ca 100 km long belt of 1.90–1.87 Ga metavolcanosedimentary rocks. Ten different Bastnäs-type deposits have been sampled in order to assess the origin of ore-forming fluids in these systems. Magnetite and quartz have d18O values ranging from -2.3 to +1.1‰ and +7.2 to +8.3‰ respectively. Mineralised carbonates have d18O values between +5.8 and +7.2‰ and d13C values between -5.4 and -3.3‰. Temperature calculations based on the O-isotope composition of mineral pairs, combined with available fluid inclusion data, suggest primary mineralisation at ca 650–400°C. For these temperatures, calculated equilibrium fluids have d18O values that range from those typical of magmatic fluids (+6 to +8‰) to lower values (down to +3‰). Variation in carbonate O and C isotope data are consistent with interaction between local Palaeoproterozoic carbonate rocks (d18O = +12.5 to +19.6‰ and d13C = -1.8 to +1.7‰) and fluids of a magmatic origin. It is suggested that the Bastnäs-type REE-magnetite mineralisations formed as a result of reactions between local carbonate units and high-temperature, magmatic-dominated hydrothermal fluids during 1.90–1.87 Ga (Svecofennian) syn-volcanic activity.CITATION:Sahlström, F, Jonsson, E, Högdahl, K, Harris, C, Troll, V R and Jolis, E M, 2015. O and C isotope study of Bastnäs-type rare earth element mineralisation, Bergslagen, Sweden, in Proceedings PACRIM 2015 Congress, pp 439–444 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By E T. Baker, J A. Resing, S L. Walker, V Ferrini, F Martinez, R Haymon

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Enumerating active sea floor hydrothermal sites has been a challenge since their discovery almost 40 years ago. High-temperature hydrothermal sites are readily discoverable, primarily by detecting mineral-laden plumes, but working at these sites poses severe environmental and operational difficulties. Low-temperature vent fields, which may represent waning of venting from high-temperature systems, may be more accessible but are more difficult to locate. Over the last decade, however, oxidation-reduction potential (ORP; aka Eh) sensors capable of detecting minute concentrations of reduced hydrothermal chemicals have been successfully used to pinpoint such fields. In this extended abstract, we use ORP anomalies observed during continuous (towed sensor) plume surveys to estimate site frequency along four intermediate- to fast-spreading ridge sections. From these data, we estimate site frequencies between five and 16/100 km for these ridge sections. Previous camera surveys on the fast-spreading East Pacific Rise support these frequencies. These rates are much greater than the frequency of ~0.5–5/100 km, generally increasing with spreading rate, derived from well-surveyed ridge sections in the InterRidge database (InterRidge, 2014). The higher frequencies arise because ORP sensors are able to distinguish between sites as close as ~1 km and identify sites with negligible or no optical plume signal.CITATION:Baker, E T, Resing, J A, Martinez, F, Haymon, R, Walker, S L and Ferrini, V, 2015. How leaky are oceanic ridge axes? A new assessment of the spatial density of submarine hydrothermal discharge, in Proceedings PACRIM 2015 Congress, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By T Baumgartl, R Akesseh, M Edraki, B Usher, M Shaygan

With the continuing demand for industrialisation and urbanisation, the rate of mining and processing lower grade ores will also increase, producing large quantities of waste. As extreme weather events associated with global climatic changes are to be expected, the risk from mine tailings management will also increase (Edraki et al., 2014). In sulfide rich tailings, weathering within the critical zone controls the fate and distribution of the contaminants such as copper, zinc, and lead in the environment (Hayes et al., 2014). Tailings evolve geochemically and physically with time as they age under the influence of complex interacting factors. Understanding of the complex interactions between these controlling factors is important for predicting and mitigating the potential risks associated with sulfide tailings such as generation of acid mine drainage (Lindsay et al., 2015). Wetting and drying initiates weathering processes, influencing the hydrological, geochemical and geomechanical properties of the tailings. In semi-arid climates where evaporation exceeds precipitation, salts may precipitate within the pore system as well as on the tailings surface. These salts become the temporal sink of heavy metals until the next episodic rainfall (Nordstrom, 2011, Grover et al., 2016). Therefore, using kinetic and static test to describe the trajectory of these material evolutions without considering the complex interactions could potentially lead to erroneous prediction. In order to understand these relations, the effect of drying and wetting cycles on the hydrological, geochemical and geomechanical properties of ageing tailings was studied to draw conclusions for advanced tailings site rehabilitation and mine closureCITATION:Akesseh, R, Shaygan, M, Usher, B, Edraki, M and Baumgartl, T, 2018. Wetting and drying cycles as a means to determine the effect and consequences of tailings ageing, in Proceedings Life-of-Mine 2018, pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By A Buckingham, R M. Hancock

The underground Sunrise Dam gold mine commenced in October 2003 to extract ore from a series of orebodies with various dips, widths, and ore grades over a strike length of 1.5 km. To successfully operate flat stopes it was identified that a means to extract ore left behind after blasting in stopes with dips ranging from 15 to 40 degrees was needed. Various options were available, which included a bulk water cannon, hand held high-pressure water jet, remote controlled small dozer, several mini excavators and finally a specialised remote controlled excavator from the demolition industry. Trials were commenced for the bulk water cannon option in 2006 that proved that the concept worked, however, the system was too cumbersome to set up for use in cycle with production. Hand washing down using mine (low pressure) water with a two-inch bullhose proved of limited value. The small, one metre high remote controlled dozer as used in South Africa was reviewed, but the steepness of most of the stopes precluded this machine. The hand held high-pressure water jet option is still being investigated; with safety factors still being addressed. Several mini excavators were trialled to clean out the flat stopes with generally poor results, the machines being either too large to fit in the drives and pull ore down or too small with too short reach to effectively and efficiently pull ore out of the stope. In early 2007 a Brokk 330 remote controlled excavator was trialled on site with the low profile of the machine and unique arm configuration proving an effective tool for pulling ore from the footwall of short, flat stopes. A Brokk 330 remote controlled excavator was purchased in late 2007 and is currently in operation.

Jan 1, 2008

By Churchill J

A suite of software programs has been written to provide the field engineer or geologist with the capability to collect and store data directly into small, portable handheld computers. This allows the engineer and geologist to collect data in a more efficient manner as the data is collected in sequence and is verified at the time. Typical applications for this software include geological and geophysical logging, trucking surveys, mine surveying, condition monitoring, ventilation surveys and maintenance systems. The software allows the user to construct his own electronic notebook by structuring data input to the computer in a similar manner as is now done on pre-printed forms. The user can store all valid entry codes or numeric ranges in a dictionary and all data inputs made are validated against this dictionary. Once constructed the user may call the electronic data sheet into the unit and collect data which will be stored into the unit which has the memory capacity to record data for up to periods of 60 hours. The data can then be automatically transferred to mini/microcomputers for immediate analysis and report generation. The software may be used on a variety of handheld computers.However the generally rugged environments found in the mining industry limit the choices. In particular the authors have selected a unit weighing a little over one kilogram, which is rugged enough to fall off an underground survey vehicle, and survive when accidentally immersed in water,without losing data. This paper describes the software developments in detail. The project development work to produce this system has been funded by a grant from the Australian Mineral Industries Research Association and is supported by a number of large Australian mining companies.

Jan 1, 1986

Many mining companies, by their remoteness of location from source of power, have to generate their own power and must experience the same problem that had to be met when deciding to increase the capacity of the power station. At present the Company is treating approximately 54,000 tons of ore mined per month, and the present shift average load. is approximately 8,500 kW. at 0.8 power factor, generated at the power plant, the observed peak load being 10,500 kW.It is proposed to increase the tonnage of ore treated to include 36,000 tons of copper ore, in addition to the present 54,000 tons of lead ore. The average load is estimated to be approximately' 16,000 kW. with a peak load of 17,500 kW. The estimate provides for power of 1,000 kW. to be supplied to the north end leases in the next 12 months, also for increased ventilation in the mines.There are installed in the main power station three turbo alternator sets each of 5,000 kW.; normally two sets are run in parallel and one set is a standby unit. A 12,500 kW. set is being installed and proposed loading with the increased tonnage will require the 12,500 kW. set and one 5,000 kW. set, or alternatively, the three 5,000 kW. sets When the 12,500 kW. set is down for service. When the original plant was installed some 25 years ago, the switches selected and installed in the main 3,300 V. power plant switchboard were rated at 150 MVA and the substation distributing centres located at the surface of the mine, in the mill, and in the smelter, were purchased as having a rupturing capacity of 100 MVA, and the stator...

Jan 1, 1953

The GDR has extensive lignite deposits at its disposal, which formed the basis for the development of an independent energy source after 1945 and which will retain their significance well beyond the year 2000 (see fig. 1). In 1946 lignite output was about 110 x 106 t. In 1985 312x 106 t was produced and in 1988 the planned output will be ca. 315 x 106 t. Thus, the domestic produc- tion of lignite covers ca. 75% of the GDR's primary energy requirements. More than 80% of the electrical energy is gener- ated by the use of lignite and about 12% by nuclear energy. In addition to this, about 18 x 106 t/a mineral oil and about 6 x 109, m3/a natural gas are imported, predominantly from the Soviet Union. The lignite deposits of the GDR are of Tertiary origin and are recovered exclusively by opencast mining. There are two large regions (fig. 2): - in the region east of the river Elbe (Cottbus/Senftenberg- "Niederlausitz") and - in the region west of the river Elbe (Halle/Leip- zig/Magdeburg). These deposits differ in geological age and conditions of depo- sition, consequently there are differences in their chemical and physical composition and, thus, in their uses. The younger Mio- cene coals of the main region in the East of the river Elbe belong to the epirogenetic type and have a low content of ash and sul- phur. Among other things, they are suitable for the production of brown coal high-temperature coke (Lauchhammer and Schwarze Pumpe). The older Oligocene coals of the Halle/Leip- zig region are bitumenous in certain areas. Therefore, they form the basis for production in low-temperature carbonizing and chemical plants. In the Halle-Magdeburg region, where the lig- nite is in contact with the underlying Zechstein subdivision, so- called "salt coals" are found.

Jan 1, 1989

ALTHOUGH discovered as long ago as 1817, by Strohmeyer, the use of cadmium did not become in anyway general for nearly a century. Its properties, although well known, did not recommend it to users of metals generally, and it was, on the whole, regarded more in the light of a nuisance to zinc producers than anything else. Its real value was not appreciated until both the United States of America and Germany, who are entirely dependent on outside sources for their supplies of tin, were faced with the unpleasant fact that their tin stocks were being rapidly depleted, with practically no prospect of having them replenished. This resulted in serious efforts being made in the UnIted States of America to conserve what tin was available, and, as a consequence, several metals were tried in the hope that they would prove satisfactory substitutes for tin. Among these was cadmium, and it was found that cadmium could replace tin in a manner sufficiently satisfactory to permit of its use in many directions where tin had been used before.It is on this ability of cadmium to replace tin that its use became in any way general at first; but since then new avenues of development have been opened up in which its physical and chemical properties are proving their value. It is highly probable that its use will extend very considerably as time goes on. OCCURRENCE OF CADMIUM.There are several cadmium minerals known, but none of them occur in profitable quantities as ores. The cadmium of commerce is derived almost entirely from zinc minerals and ores in which it is almost invariably present in proportions which are usually very small. Cadmium behaves metallurgically almost the same as zinc, and hence constitutes a fraction of 1% of almost all spelter.

Jan 1, 1923

IN preparing a sample of refined lead for analysis, it is necessary to exercise great care to avoid contaminatien, as the amounts of the various impurities present in market lead are very small. The lead is cut into convenient-sized pieces, which are flattened out with a hammer, so that, on putting tbe lead through the rolls, strips of about one inch in width and Ij32iu. in thickness are obtained. The hammer, anvil, and rolls should be carefully cleaned before use. The strips oflead are cut up into pieces of about one inch square. If the lead is roIled out very thin and cut up into small pieces there is considerable risk of the acid acting too violently and causing loss through frothing over. A blank assay on all the reagents used should becarried right through, along with the actual analysis of the lead. This is of the greatest importance, particularly with regard to the determination of such impurities as iron, sulphur, arsenic, and antimony.METHOD OF ANALYSISThe method of analysis is as follows: Take two lots of 600 gIm. each, place in a large beaker, add 2000 cc. distilled water and 750 cc. concentrated HNOs. Cover with a clock glass and warm on a hot asbestos plate until all action ceases. (If any white precipitate forms, filter off and examine for Sn and Sb.) Add 420 cc. H2S04 (1-1), and stir well while adding the acid: Allow PbS04 to settle, pour off the clear liquid into a 12-in. porcelain evaporating dish, and start evaporating down, the dish being placed directly on an 8-in. ring gas burner. Wash the precipitate three times by decantation using approximately 1200 cc. hot water for each washing, and stir well...

Jan 1, 1922

By Misk A

Several logging methods are presently available to the oil industry for the evaluation of formation porosity: the Sonic and Neutron logs are already widely used, the Gamma-Ganmia log is being progressively introduced. The readings of these instruments are primarily a function of the rack-porosity, hence the general term of "porosity tools". Apart from porosity, however, other variables such as type of fluid in the pores, nature of matrix and degree of shaliness have an important influence.The response of each device is a different function of such parameters: therefore, a cci bination of porosity tools can lead to information on these variables in addition to the evaluation of effective porosity.For example, the presence of gas; rather than water or oil, in a formation which is not deeply invaded, will tend to give Neutron derived porosity values which are too 'low; on the other hand, the Sonic derived porosity: value will be too high in such- a case. For the same porosity, the Sonic gives a longer transit time in sandstone than limestone, whereas in the low porosity range, the Neutron will read more counts per second in a sandstone than in a limestone of the same porosity. The presence of shale also affects the readings of the various porosity tools in different ways so that the combination of two or more methods may lead, in some cases; to an evaluation of both the-effective porosity and the shale, content.In conclusion, it may be said that the various porosity tools pre-sently available, are, to a large extent, complementary, and that in many problems the use of two porosity tools, instead of one, is very likely to bring valuable additional information.

Jan 1, 1962

By J Galvin

This paper addresses the actions of the Australian mining industry, its regulators and educational providers towards ensuring that a pool of competent mine managers is maintained in Australia and that mine management remains a desirable career path for future mining professionals. The Australian and global mining industries are experiencing an acute skills shortage. Mine managers, traditionally drawn from the ranks of mining engineers, are at the sharp end of this shortage. Exacerbating the shortage is a perception that a professional mine manager is not an attractive career option. This perception is influenced by the following forces which combine to make the role of a modern mine manager very demanding:legislative requirements for owners and managers to ensure (guarantee) the safety and health of employees; an increasing trend towards prosecution over exposure to risks to health and safety a need to be more aware and responsive to community and environment; financial, technical and æpeopleÆ pressures traditionally associated with the job of managing a mine; and mine management roles being filled by younger and less experienced professionals. Universities and other educational providers have the challenge of both ensuring that undergraduates are exposed to these issues during their study and continuing to promote mine management as a desirable career option. Anecdotal and statistical evidence indicates that young graduates are choosing and remaining in technical roles rather than taking on the challenge of mine management. Furthermore, it is suspected that the issues referred to above are contributing to the low retention rate of young professionals at mine sites. The challenges are not insurmountable, however. This paper reviews the initiatives of industry, the regulators and educational institutions in addressing these challenges. It includes a focus on:prosecution policies and their impacts, tertiary education program content and delivery modes, CPD initiatives of the Mine Managers Association of Australia, and alternative pathways for obtaining mine management qualifications.

Jan 1, 2006