Search Documents

By X Dahe

SLon vertical ring and pulsating high gradient magnetic separators possess excellent mineral processing ability and have been widely applied to process oxidised iron ores. SLon centrifugal separators are applied to clean the SLon magnetic concentrate and remove quartz and other gangue minerals associated with a small portion of magnetite.This paper introduces the application of this technology in Hai Nan, Da Hong Shan and An Shan for processing oxidised iron ores.

Jul 11, 2011

By N Esmaeili, M Saghaeian, L Hosseini, V Sheikhzadeh, R Hejazi

Ore roasting has long been used for beneficiation and assay upgrading of different ores. In this process, which is mainly used for sulfide ores, the ore is heated to a high temperature. More specifically, it is a metallurgical process involving gas-solid reactions at elevated temperatures. Some types of Iron ore are weak in magnetic properties. Hematite, goethite and limonite are classified in this group. Unlike magnetite, which shows strong magnetic susceptibility, these ores are hard to beneficiate through magnetic separation route. Many researches have focused on gravity separation and flotation routes for upgrading these ores and these methods have also been utilised in the industry. One of the methods to whose industrial application less attention has been paid is magnetising roasting in which the non-magnetic iron ore is transformed to magnetite which is further beneficiated through magnetic separation. In this study, magnetising roasting tests have been performed on one goethite sample in order to check the feasibility of using this method for this specific ore in industrial scale. It is worth mentioning that high intensity magnetic separation have been performed on this sample before but the achieved results were not promising. Results have revealed that through magnetising roasting magnetite content of the ore could be increased from 1.7 per cent up to about 25 per cent. FeO content of the feed sample was increased from 1.03 per cent up to around 9.25 per cent. Also optimum size distribution for achieving the best results in magnetising roasting for this sample has been determined through this study. The best results were achieved when the ore size was 0–10 mm. The effect of coal ratio, time and temperature on the process have also be studied. A coal ratio of 5 per cent, time of 30 min and a temperature of 850°C were determined to be the optimum conditions. Finally, the technical feasibility of utilising magnetising roasting for this specific ore has been confirmed.

Aug 24, 2022

By C MacRae, N Wilson

CSIRO Minerals has recently developed an electron microprobe (EMP) based imaging (or mapping) method for characterising ilmenite concentrates. The method requires an electron microprobe analyser to collect elemental X-ray maps which are then processed via an in-house developed software module (CHIMAGE). The type of information readily available from EMP mapping includes; primary phase identification, modal analysis of phases, chemical analysis of individual phases, textural information (eg the alteration stages in the formation of leucoxene or pseudorutile from primary ilmenite and the development of macro-porosity), and the identification of coatings or pore-fill material. All of these parameters will impact on the choice of future downstream processing options considered for any particular ilmenite concentrate. The method has been demonstrated to be a sensitive analytical tool for assessing the distribution of aluminosilicate minor impurities in ilmenite feedstocks from the West Coast of Australia and also for characterising the complex chrome-spinel gangue phases common in East Coast ilmenite concentrates from the Murray Basin.

Jan 1, 2001

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

By A Bennett, S Arndt

Minerals and Metals Group Pty Ltd (Golden Grove Mine) commissioned a comprehensive study of the life of mine using advanced 3D stress modelling. Essential input into the modelling was the proposed mining sequence, itself the culmination of years of planning and geotechnical experience gained in comparing actual performance to predictions. The modelling approach addressed the whole of mine at a scale of 5 km. There were however several magnitudes of scale to address, from the scale of laboratory testing (0.05 m), to drive size (5 m), extraction size (50 m) and stope size (500 m). Scaling was therefore an integral part of the procedure. The constitutive rock properties in terms of peak and post-peak behaviour varied with the scale. At the laboratory scale, the constitutive relationships for all the main rock units were determined in 3D as well as recovering the in situ stress using the rock memory technique, deformation rate analysis (DRA), whereas at the larger scale the properties were varied to match observations.The modelling, using non-linear analysis to account for rock mass yield and peak-residual strength, demonstrated that if the planned extraction sequence and stope geometry had been pursued there was a high probability of large volumes of excess shear stress being released. However, it was not possible to identify whether the excess shear stress (ESS) will release as one large event or many smaller events. The mining approach was to modify the extraction sequence/stope geometry to manage the hazard. This is where the economic advantage can be realised.Alternatively or in combination with further modelling, the volume identified with the predicted high ESS or energy release could be intensively explored for structures having adverse orientation to the stress change and with sufficient areal extent to release the ESS. The microseismic data can be interrogated for the likelihood of a large event to support the hypothesis of a singular release versus multiple releases of smaller events. If the initial planned extraction sequence had to proceed as designed, changes to dimensioned stopes would be recommended for risk mitigation. Mine planning could as an option, modify the sequence and the extraction could then be remodelled.CITATION:Bennett, A, Arndt, S and Dight, P M, 2014. The economic advantages of detailed geotechnical assessments for extraction sequencing, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 243–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Fabjanczyk MW, Nemcik JA, Matthews SM

The major strata control considerations which affect the optimisation of roadway driveage in highly stressed strata is the performance of reinforcement placed and the extent of stress induced rock deformation. High development rates and opening stability requires efficient rock reinforcement and stress relief strategies which maximise the integrity of the rock about roadways created. Current studies demonstrate the capability to reduce lateral stress distributions across panels and research is aimed toward a higher capacity bolting system. It is the intention to provide industry with more efficient reinforcement and stress control alternatives which will allow high production development equipment to operate without the restriction of delays caused by poor ground Conditions.

Jan 1, 1988

By M Saghaeian, A H. Baladastian, A Dehghani Ahmadabadi, V Sheikhzadeh, R Hejazi

With the declining of high-quality hematite and magnetite iron ore reserves and the increasing accumulation of material resulting from mining and beneficiation operations that appear as lowquality depots and discharged materials in tailing dams, the necessity of recycling these reserves is increasingly becoming a critical demand. The Chadormalu iron ore mine is among the largest deposits of magnetite-hematite iron ore in Iran. In this mine, the total wet processing tails accumulated in tailing dams are over 92 Mt containing 25–40 per cent Fe. Laboratory and pilot tests on tailing samples led to the design and implementation of the Chadormalu Tailing Recovery plant (CTR) with a unique process circuit in Iran. In the CTR plant, after three steps of re-pulping with spiral classifiers and sanding machines, the underflow is concentrated by two stages of WMIMS and produces 64 per cent Fe grade magnetite concentrate. The tailings of the drums are mixed together and introduced into the hematite recovery section, including two stages of VPHGMS separators, and 60 per cent Fe grade hematite concentrate is produced. This plant has been in operation for over ten years with a total yield of 18.93 per cent. Due to changes in the materials extracted through new tailing dams, the quality of the final concentrate dramatically dropped to 56.36 per cent Fe and 0.79 per cent P; therefore, applying reverse flotation and removing phosphorus from the final concentrate was inevitable. By using this approach, upgrading of the concentrate to 63.01 per cent Fe and 0.05 per cent P was obtained. Furthermore, regarding the high amount of phosphorus in the tailing streams, direct flotation has been designed to produce apatite concentrate as a by-product stream through a flotation system comprising series banks of Rougher, Cleaner, and Re-Cleaners flotation cells. Hence based on the results, at optimum conditions, a final apatite concentrate with a yield of 15.78 per cent and 14.06 per cent P could be achieved. Successful implementation of this project has led to the production of magnetite-hematite and apatite concentrates with annual capacities of 250 000 and 45 000 t, together with total yields of 11.59 per cent and 6.19 per cent (includes de-sliming of apatite flotation feed), respectively.

Aug 24, 2022

By B Banerjee, H Masoumi, X Shen, S Raval, D Tannant

Structural mapping of pit walls can be performed using digital images and photogrammetry software, but the performance is limited by weather and environmental conditions including dust, rain and light. On the other hand, active sensors such as terrestrial laser scanners (TLS) and total stations (TS) suffer from vertical orientation bias and occlusions when persistent discontinuities dip at the same angle as the scanner line-ofsight. The recent development of the compact light detection and ranging (LiDAR) systems has made it possible to mount these sensors on unmanned aerial vehicles (UAVs) or drones which offer the potential to overcome limitations that are inherent in existing mapping systems. This study details the research involving integration and application of an advanced UAV-LiDAR system for structural mapping of a highwall. A state-of-the art laser scanner with an inertial measurement unit (IMU) and real-time kinematic global positioning system (GPS) was integrated on to a UAV. The system was first tested in a laboratory condition. Then the UAV-LiDAR system was employed to map a highwall of a coal mine. The planned flight trajectories tested the system at variable distances from the highwall face and at various speeds. The raw data collected from individual sensors were fused, filtered to remove noise, and segmented to produce a surface scan model. Finally, the point density and surface coverage were measured using the surface scan model of the highwall. The parameters were compared with equivalent measurements computed from a reference TLS data. The study demonstrates the capabilities of a UAV-LiDAR system to generate accurate and occlusion free data for mapping highwall geological structure with very quick and efficient flights in the field. CITATION:Raval, S, Banerjee, B, Shen, X, Masoumi, H and Tannant, D, 2018. Evaluation of a UAV-LiDAR system for mapping geological structures in an open pit highwall, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 496–503 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By L Galisson, E Audigé, D Sowers

Establishing a robust geotechnical instrumentation and construction monitoring plan is one of the keys to the successful delivery of the world’s largest soft-ground bored tunnel in Seattle, Washington. The paper describes and provides a return of experience on current and best practice for monitoring tunnelling projects in urban areas. The owner’s contractual approach is discussed to highlight the flexibility of the design-built contract in achieving equal or better solutions by allowing for the use of innovative technics. Special attention is given to the management and involvement of third parties (building owners, utility owners), including the public, to overcome all challenges faced during the installation of the monitoring system in downtown Seattle for over 1000 instruments. Finally, the authors present the strategies implemented for managing the monitoring data and communicating with the owner, contractor and stakeholders.CITATION:Sowers, D, Galisson, L and Audigé, E, 2014. Current and best practice for monitoring tunnelling projects in urban areas – Alaskan Way bored tunnel, Seattle, Washington, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 441–450 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The Imperial Smelting Process (ISP) for the simultaneous smelting of zinc and lead was developed at Avonmouth from the 1930's with activity intensifying in the late 1940's/early 1950's. Present operations are based around the No.4 furnace which was built in 1967. Development during the 1980's has been driven by the need to sustain operations at low metals prices and has been aimed at reducing manning whilst increasing output. Although hit by several major plant disruptions, progress has been steady, culminating in a ú10 million capital programme in 1988?89 to upgrade the operation. The most important technical developments, reflecting the needs of the 1990's have, in the sintering area, included improvements to feed conditioning and sinter quality, a 20% uprate in production capacity by debottlenecking, and pilot work leading to the installation of a Boliden-Norzink mercury removal plant. In the smelting area the ISP furnace has been rebuilt, with a redesigned bottom section to eliminate earlier operating sensitivities, and to achieve higher blowing capability, and at the zinc refinery the columns have been rearranged for more flexible operation and higher capacity.

Jan 1, 1989

By D Kay, M Lovitt

Mass Blasts are generally required at the completion of longhole stoping cycles to maximise the recovery of ore from a specific orebody. During the course of mining, the practice is to leave pillars of ore to support the opening left by extracted ore and to mitigate stresses from working areas of the stope. These pillars usually contain ore that has been included in the resource evaluation and is highly valuable to the mining operation. Due to their stressed nature, the removal of pillars by conventional blasting techniques, through small blasts, can result in pillars being reduced beyond their critical size and ultimately failing, rendering the ore unrecoverable. The AurionGold Kanowna Belle Gold Mine operates a Mine to Mill philosophy. This philosopy requires the fine tuning of blasting to provide the best possibe ore feed at the highest grade for mill productivity. This means that ore to the mill must be well fragmented from blasting that provides high extraction rates from draw points, with minimal dilution from overbreak or fall off, and sized to maximise SAG mill throughput. The AT04 Mass Blast contained significant ore reserves which were required to meet gold production targets. KBGB needed the AT04 Mass Blast to perform as well as if not better than conventional stope blasts to maintain mill production. This paper describes the circumstances, planning philosophy, techniques, including the use of Electronic Initiation Systems and Bulk Emulsion Explosives, and results that provided a highly successful outcome.

Jan 1, 2002

Sampling errors result from heterogeneities within the lot under study. Within a rock mass in situ heterogeneity results in the geological nugget effect, which accounts for most of the natural variability. In broken rock, constitution and distribution heterogeneities are important. A major result of the constitution heterogeneity is the Fundamental Sampling Error (FSE) which is the smallest residual error that can be achieved. It cannot be eliminated, but can be minimised and refl ects the fact that the broken rock sampling process is never completely free of error. Together with other sampling errors, FSE contributes to the total nugget effect. The FSE for a sampling protocol can be evaluated using the so-called Gy equation. Its practical applications to low-grade gold ores have often been unsuccessful due to problems linking the FSE and minimum sampling mass and the defi nition of key parameters such as the liberation diameter. Well-designed sample protocols minimise the total sampling error and hence the nugget effect. Reduction of the nugget effect is a key requirement for all sampling programs whether related to exploration and resource evaluation, metallurgical test sampling, grade control or metallurgical plant sampling. This contribution reviews the relationship between heterogeneity, FSE and nugget effect in gold deposits; and emphasises the need for FSE management throughout the mine value chain.

Aug 1, 2010

By B Belle

"Mines around the world are inherently and operationally diverse. Current methodologies for the design of mine ventilation and cooling infrastructure involve controlling major safety and health hazards. Globally, it can be estimated that mine ventilation systems from various commoditiescirculate over 150 000 m3/s of exhaust air through shafts. Additionally, over 2 000 000 workersare transported every day through shafts in labour-intensive mining countries like China, India,Southern Africa, and the Americas. A key objective of this paper is to share experiences and provide a case for the revision of ætime-honouredÆ ventilation design parameters based on a benchmarking exercise on design exhaust shaft velocity from various global operations (gold, diamond, platinum, coal and base metals). An active fi eld observation on exhaust shaft velocity has indicated that, regardless of the commodity or continent where the mine operates, almost all life-of-mine (LOM) design parameters provided are in the same range of 20 m/s to 22 m/s, which is not convincing considering signifi cant variations exist in shaft depths, geography, commodity, operating and capital costs. From a due diligence perspective, there are no documented views that are available on the most widely used design exhaust air velocity. Based on the global exhaust shaft velocity data, it is noted that a significant portion of shaft velocities are outside the current design velocity of 20 m/s (some operating up to 30 m/s) and other signifi cant portions of the exhaust shafts operate in the critical velocity range. In the case of Australian coal mines, limited data suggests that none of the mines have ever reached the LOM design exhaust shaft velocity. It is self-evident that when the shafts are not operating at their design quantities either the mine system resistance is low or the ventilation and main fan is operating ineffi ciently. The most common reasons given for not reviewing the shaft system were, ætime-honouredÆ design parameter are being used and cannot be changed, mine fan pressure limits, possible fan blade damage, possible spontaneous combustion risks, leakage or simply did not consider such a possibility. In conclusion, the study has reiterated the historic lessons that a safe and expensive airway should not be utilised uneconomically by circulating too litt le air through it."

Jun 1, 2012

Mineral formations, accumulated during technogenic activities greatly influence an economic and ecological situation in the Kola North. On the one hand, the dumps from extraction of mineral resources, tailing ponds of beneficating plants, ash dumps, wastes of metallurgical and mechanical engineering productions destroy the regionÆs environment and require taking certain measures and costs to bury or protect from weathering, oxidation, etc. On the other hand, technogenic mineral formations contain a lot of valuable scarce components. The amount of solid wastes increases annually, causing damage to ecology and economy. Researches conducted in recent years showed a possibility and economic expediency of comprehensive processing of wastes from different enterprises in Murmansk region and their use for production of new competitive commodity output, possessing high consumer properties. Thus, involving mineral wastes from Khibiny apatite deposits into hydrometallurgical industrial processing provides the basis for setting up a large beneficating-metallurgical complex. In this case ores and wastes from other deposits on the Kola Peninsula, containing titanium, rare, rare-earth and other valuable elements, may be involved into processing. Establishing such a complex will allow to organise a deep processing of natural resources, utilise some production wastes, improve ecological security and supply production with competitive output. Expanding the complex implies not only involving new mineral raw material into processing, but mainly deepening raw material processing, maximum utilisation of local natural resources and obtaining a wider variety of prime products.

Jan 1, 2002

By M G. Aylmore

Thiosulphate is an attractive alternative reagent to cyanide for processing gold ores. It is relatively cheap and non-toxic, forms relatively strong gold and silver complexes, and readily leaches gold ores in ammoniacal solutions, catalysed by Cu(II). It is particularly suited to carbonaceous ores where the recovery of gold by cyanide is poor. However research over the past 20 years has identified a number of issues and impediments that must be understood or overcome before an overall process can be demonstrated as practical and economic for typical oxidised gold ores. This paper reviews our current understanding of thiosulphate chemistry and mechanism of gold dissolution, and discusses the stability of thiosulphate and polythionates. It then reviews the results of leaching various gold ores that have been reported in the literature, discusses gold recovery options, and considers environmental and toxicity issues. Some of the issues that require further research include decreasing the oxidation of thiosulphate by Cu(II) or other oxidants, increasing the extraction of gold compared to cyanide, and understanding the variation in gold recovery between ores. More work is also required to minimise the effect of polythionates on gold recovery using resins or alternative absorbents, to improve the elution of copper and gold from resins, and to recycle or minimise the concentration of reagents.

Jan 1, 2002

By M Laxman, A Kundu

After multiple tailings dam failures in recent times, the owner organisations have made increased efforts to step up the governance systems to industry best practise in the design, construction and operational management areas. The measures include but are not limited to, site investigation, rigorous peer review (both internal and external), certification through appropriately qualified personnel and improvement in operational management practises. While a lot of focus is on design and operational practices, the construction stage requires adaptation (both in terms of materials and approved design) and immediate decision making on site. Work undertaken in these areas is mostly irreversible and sometimes poses serious threat to the future TSF raise/ expansion planning and may lead to reduced life of the TSF and additional risk to the Owner.This technical paper will discuss some challenges and highlight the importance of appropriate processes to achieve a successful construction regime. The process will include a robust quality control/ quality assurance process, a team of designer-constructor-owner with suitable skills and technical understandings and robust documentation of the entire construction process from day 1 to the completion of construction.CITATION:Kundu, A and Laxman, M, 2018. Robust construction and quality assurance culture for tailings storage facilities – equally important as robust design and review practice, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 111–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By X Yang, T Zhang, Z Li, Z Yan, M A. Williams, S Qin, P Wilson

Continuous development of complex new steel grades to meet the ever-increasing demand of high performance causes recurrent issues in steel continuous casting such as surface quality defects (eg cracks, depressions, deep oscillation marks) and productivity challenges (eg faster casting, near-net shape casting). Continuous casting of steel is a highly successful metallurgical process. Much of this success can be attributed to the performance of the casting powder that is added to the top of the mould, creates a liquid slag pool as it is heated, and forms a slag film between the watercooled copper mould and steel shell during its passage down the mould. Mould powder selection is a compromise between the conflicting requirements of heat transfer and lubrication. In an EU RFCS (Research Fund for Coal and Steel)-funded project, various techniques are developed to offer the opportunity to adapt the slag film to meet the conflicting needs in different parts of the mould such that mild cooling can be generated in the meniscus, mid-broad face or corner areas whilst maintaining lubrication and offering higher cooling rates in other areas of mould. This has significant potential to address the industrial issues in product quality and productivity of continuous casting. This paper reports, as part of the EU RFCS project, the determination of crystallinity and porosity in slag films for casting challenging and innovative steel grades using new methods. In comparison with the methods such as X-ray powder diffraction (XRD) analysis and optical microscopy / scanning electron microscopy (OM/SEM) analysis that are currently adopted by the industries, EBSD (electron backscatter diffraction) has been employed to determine the crystallinity of the slag films taken from industry casters. X-ray computed tomography (XCT) plus 3D image reconstruction has been used to determine the slag film % porosity with pore volume, pore size distribution, and pore location, which can be linked with the performance of the slag films during casting different steel grades.

Jun 19, 2024

By Z Fu, E Topal, O Erten

"Mine waste rock management involving waste rock movement and placement, is a critical aspect in the planning of open pit mining operations, as the waste rock haulage cost can be the largest portion of the mine operating cost. The concept of sustainable development in the mining industry also encourages environmentally friendly waste dumps that have zero hazards to people and the surrounding environment. Therefore, a detailed waste management schedule must satisfy economic and environmental considerations. However, the available tools in the market cannot provide optimal waste dumping schedules to meet all these constraints. This paper introduces a user-friendly and automatic tool to optimise the waste dumping schedule, which minimises the haulage cost, and covers the encapsulation of reactive materials to minimise acid mine drainage problems. This tool has been developed by using a new mixed integer programming (MIP) mathematical model that considers both single-lift and multilift dumping scenarios. The application of the proposed tool on a data set collected from a gold mine shows that the multilift dumping scenario has provided a more flexible and economical waste dumping schedule than the single-lift scenario, and both scenarios satisfy environmental requirements.Citation:Fu, Z, Topal, E and Erten, O, 2016. A Modified Software Tool for Mine Waste Rock Dump Planning, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 229–242 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By D J. Bradshaw, E M. Wightman, C L. Evans, B Triffett

During the commissioning phase of Prominent Hill, periods of reduced recovery were experienced with higher-grade ore blends. This was unexpected and as part of the process to identify the cause, surveys were conducted in May 2009, with two different ore blends (copper grades: 1.94 per cent Cu (blend 1) and 2.49 per cent Cu (blend 2)). Metallurgical performance was assessed in terms of rougher recovery and grade with consideration of both pulp and froth effects. In addition, hydrodynamic measurements (gas hold up, bubble size, superficial gas velocity) as well as measurements of bubble load and top-of-froth grade were taken during the surveys and full mineralogical assessment of selected streams completed to characterise the nature of the differences. The metallurgical results showed that the lower performance was obtained with blend 2 which contained the higher amount of chalcocite and was higher-grade. Analysis of the survey data showed that for both ore blends more than half of the copper loss occurred in the +38 ¦m size fractions. Almost 30 per cent of the copper in the +38 ¦m fractions that reported to the rougher tails during processing of blend 2 was liberated compared to less than five per cent for blend 1. Additionally almost 60 per cent of the copper in the +38 ¦m fraction of blend 2 was chalcocite compared with approximately 20 per cent in blend 1. This paper discusses the sensitivity of the chalcocite-to-surface chemistry effects causing marked reductions in recovery either through reduced pulp recovery or froth phase (detachment) effects. The reagent suite and operating conditions were subsequently changed and the recoveries increased substantially and the sensitivity to ore changes eliminated. It should be noted that subsequent optimisation work, which focused on recovery improvement, has led to copper recoveries of over 90 per cent being achieved.CITATION:Bradshaw, D J, Wightman, E M, Evans, C L and Triffett, B, 2012. Characterising the reasons for the difference in performance of two ore blends in early processing at OZ Minerals Prominent Hill Operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 273-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A von Johannides, G J. van Hout, L F

In the past various systems have been used to plan the extraction of ore from block cave operations. These systems have varied from rather sophisticated models with empirical ægravity flowÆ rules applied to the very rudimentary models where only the recorded mined tonnageÆs have been accounted for against the available resource. The normal requirement of these models has been to only plan the movement of ground through the drawpoints. Little cognisance has been taken of the other parameters that affect the total mining operations. The intended purpose of the linear program planning system is to not only include the management, resource availability and geotechnical constraints, but to also include the mining rules. The paper will discuss the various constraints that have been considered, and attempt to illustrate where the system better serves the production system than previous ones. A brief technical discussion on the linear programming system is included.

Jan 1, 2000