Search Documents

By Bhattacharyya A. K>

The Pemali Open Pit Mine is situated in a small island called Bangka in Indonesia. It produces approximately 165,000 m3/year of tin ore with an average grade of 3.67 kg/m' of tin from a primary deposit. The deposit occurs at the rim of a granitoid intrusion within sedimentary beds. The rock formations, all extremely weathered, and the overlying alluvium, are exposed to a rainfall exceeding 3m/year. Serious slope stability problems are experienced at the mine, despite using overall pit slopes of 20¦-29¦, the latter resulting in a stripping ratio of 4:1. This paper outlines a computer based back analysis of a major slope failure involving some 250,000 m' of material which occurred on the west wall of the pit in February, 1984. The findings from the analysis, together with other information, are used to examine the stability of the east wall of the pit, where tension cracks developed later. The results indicate that the large influx of water was the most significant cause of such slope stability problems and a more intensified water management programme would be beneficial.

Jan 1, 1989

By Miller M. J, Bauer J. C

The continuous copper drossing process operated at Port Pine since 1962 has had limited copper removal capacity as determined by a maximum tolerable Cu/S ratio in feed and the level of sulphur in blast furnace bullion. Recent process development has been to overcome these limitations to meet increased copper throughput requirements. A sulphur addition system was developed and installed in August 1987. The system has capacity to increase sulphur input by over 150%, meeting the increased copper capacity requirement and also allowing independence from the upstream process for sulphur supply. Developments in process understanding have been applied within the limitations of the existing furnace design with a 10% increase in the maximum tolerable Cu/S ratio.

Jan 1, 1989

The Australian metallurgical processing industry has shown great innovation and progressiveness over the past ten years. During the same period, exploration activity, particularly by Australian companies, has increased substantially in Indonesia. Following feasibility studies, the decision was made to establish a metallurgical laboratory and design facility in Indonesia. An Indonesian partner was selected, and legal and corporate matters were determined. The laboratory was established but proved far more difficult than a similar undertaking in Australia. Australian and Indonesian staff were recruited and training programs, including training of Indonesian staff in Australia, were implemented. Difficulties of operating in Indonesia included: ò language difficulties ò _ local pace of life ò culture ò communications. Rewards of the decision to establish the means to present the technology to Indonesia have included: ò a contribution to Australia's export of technology. ò an opportunity to expand Normet's client base. ò the opportunity to learn aspects of a foreign culture. ò the means to establish a sound long term investment. This export of technology from the Australian mining industry to Indonesia is an example of the initiatives and capabilities shown by the Australian mining service industry.

Jan 1, 1989

An airlift pump is fitted to the screw conveyor of a decanter type centrifuge in order to pump out soft cakes which are difficult to discharge from a standard decanter. The new patented2 design improves separation performance and allows more stable operation, particularly when operating the decanter as a thickener.

Jan 1, 1989

Battle Mountain Gold Company's Paj ingo Mine is the first gold mine developed by the Company in Australia. The Mine located in northern Queensland commenced operations in September 1987. The high grade epithermal orebody is selectively mined and processed through a conventional carbon in leach/carbon in pulp (CIL/CIP) plant at a rate of 200000 tonnes per annum. In 1988 it produced 61000 oz gold and 152000 oz silver. Inadequate preoperational development of non technical management and organisational functions often leads to inefficiencies that last well into the operation. The Pajingo experience in this regard is oaTple ented by those from a number of other recently commissioned small operations. A checklist is discussed to assist any future preoperational group in focussing their attention into areas that seem to be of secondary importance at the time but often have a significant impact on overall management efficiency later.

Jan 1, 1989

By Cunneen R. D, Murray A. M

Exploration in the vicinity of the abandoned Mt Coolon mine has shown that the shape and attitude of the quartz lode is controlled by the interaction between the lode and a converging syncline. Gold grades within the lode are enhanced along intersections with a welded ignimbrite, and decline rapidly where the lode intersects unwelded ignimbrite. Mineralogy and textures indicate the vein has an epithermal origin modified by a later intrusive event.

Jan 1, 1989

By Albano C, Antila A, Flykt B

A method for relating operating variables and dewatering parameters of Thunes disc filters in the LKAB pelletizing plant at Malmberget in Sweden, via empirical mathematical models is described. Near orthogonal experimental design was used, where all independentvariables were allowed to span over their domain of variation and pseudo-randomly distributed among the experiments. The dewatering parameters are dependent on many variables and instead of using a traditional mechanistic model, an empirical model based on multivariate data analysis was chosen. The way of expressing the relation is by regression coefficients obtained from partial least square regression (PLS). Two empirical models were generated. The models were validated using an extra set of 56 experiments. The dewatering parameters were related to the design variables with few experiments, and user-friendly response surface methodology was used to determine the optimal conditions.

Jan 1, 1989

A typical large surface mine in Scandinavia has hard rock, a cold cli- mate, poor ore, a complicated vein type orebody and high labour costs. In order to survive, these mines have to maximise their ore production, minimise waste extraction and get the most out of every man hour. This article describes two examples of how inclined blastholes drilled with hydraulic percussive drills can help to meet these requirements. Both of these Scandinavian mines, Kemira Ltd's Siilinjarvi mine in Finland and Sydvaranger A/S's Bjornevattn iron mine in Norway, use inclined blastholes of 200 mm in diameter. The Siilinjarvi quarry is using inclined holes in production drilling. The Bjornevattn iron mine is blasting the final pit walls with inclined holes. The benefits gained when using inclined instead of vertical blastholes are better selectivity, better bench drilling conditions, steeper final pit walls and increased safety.

Jan 1, 1989

By Carter D

The Chairman of this afternoon's session is Dick Carter. This afternoon is the culmination of this conference. We've looked in the first session at regulation; in the second session at valuation techniques and this session we look at valuation in practice. Dick's involvement in the mineral industry has been wide ranging and distinguished. Dick has worked with BHP since 1960, when he joined BHP Steel as a commercial trainee. Dick holds a B.Comm. from the Newcastle University College of the University of New South Wales and was educated at the Australian Administrative Staff College and Harvard Business School Advanced Management Programme. During the past decade, he has headed the minerals group's Aluminium Divison, Resource Planning and Development, Non-Ferrous Metals and Business Development Organisations. Dick currently serves as Executive Director of BHP Gold Mines Limited and Managing Director of Ok Tedi Mining Limited. His experience covers Australian Manganese Company, Mineral Deposits Limited, Northern Rivers Rutile, Tasmanian Electrometallurgical Company Limited, Mount Newman Joint Venture, Worsley Aluminium and Carnilya Hill Joint Venture Operating Committee. His industry associations include the Executive Board of the Gold Producers Association, the Federal Executive of the Australian Goldmining Industry Council as well as the World Gold Council. Ladies and gentlemen, Dick Carter.

Jan 1, 1989

By Foudoulis C, Smith CB, Drew RM, Sun S-S, Sheraton JW, Hall AE

Primay (syngenetic and protogenetic) inclusions - i.e. minerals formed during or before diamond growth and encapsulated in the diamond - provide important information on the origin of diamond. Recent Rb-Sr and Sm-Nd dating of such inclusions has yielded crystallization ages older than their volcanic host, implying that diamonds are mantle xenocrysts. In this paper we report results of studies on the nature of syngenetic inclusions and the carbon isotopic compositons of the host diamond from the West Australian diamond deposits at Argyle and Elllendale. The Argyle diamonds are dominantly, of eclogitic paragensis and are characterized by strongly C depleted compositions. We have recognized an association of stone morphology, inclusion type and carbon isotopic composition amongst the Argyle stones, and on the

Jan 1, 1989

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal.

Jan 1, 1989

By Ramsden AR, French DH

The limited contrast range of conventional black and white imaging does not enable full use to be made of the dynamic range of the video signal obtained from a scanning electron microscope or microprobe. The use of false colour substantially increases the information that can be derived from such images enabling relationships to be displayed that cannot be observed in black and white. This capability is now used extensively in combination with quantitative electron microprobe analysis as a research tool for ore characterization and host rocks studies related to minerals exploration in the CSIRO Division of Exploration Geoscience.

Jan 1, 1989

By Zamel GI

The utilisation of fossil fuels, including coal (of which Australia is a large producer and exporter) is a significant contributor to the emission of greenhouse gases. Methane gas, formed during the coalification process, is present in coal seams to varying levels depending on the rank and depth of the deposit. This gas usually escapes to the atmosphere during mining operations without prior conversion to C02 or utilisation as fuel. The quantity of methane released can represent from less than one percent to more than five percent of the carbon content of the coal mined. Per unit of carbon, methane has a greenhouse impact many times that of C02. The emission of uncombusted methane to the atmosphere can therefore represent a greenhouse impact of similar porportions to that of the CO2 formed by combusting the mined coal. However, greenhouse emissions from coal can be minimised by collecting the coal seam methane and converting it to water vapour and the less damaging form, CO2. If such conversion is carried out while performing useful work, the methane can further reduce greenhouse emissions by displacing other fossil fuels. Technology has been developed to allow coal seam methane gas to be economically collected in a pure form, uncontaminated with air. This pure methane can be used to supplement natural gas supplies, to generate power or for the production of chemicals or substitute transport fuels. By collecting and utilising coal seam methane, the greenhouse impact from the mining and use of coal can be minimised, with significant reductions possible in the case of gassy deposits.

Jan 1, 1989

High resolution seismic profiling has proved a cost effective tool for defining the structure and seam geometry of Late Cretaceous-Late Miocene age lignite deposits in the South Island of New Zealand since 1981.In 1985 a total of 45 km of Mini Sosie seismic reflection was carried out in the Benhar, Hawkdun and Ashers-Waituna deposits as part of a major multidisciplinary resource investigation funded by the Liquid Fuels Trust Board. For each deposit the seismic programme involved integrating four or more intersecting Mini Sosie traverses with a grid of 1000 m spaced geophysically logged drillholes. The objective was to detect faults, with displacements ranging 30 - 100 m, which might impede mining using bucket wheel excavator systems at depths down to 300 m below surface.In general the quality of processed seismic data was high and with the assistance of ynthetic seismograms and other geological information, it was possible to identify a number of significant previously unknown faults. The success of this seismic programme ha shown that high resolution seismic profiling, used in conjunction with relatively low density drilling, can produce valuable structural and tratigraphic information at an early stage of open pit mining investigation.

Jan 1, 1989

Statistics on the imports of industrial minerals into the EECshow that the traded volume in 1987 is approximately 23 million tonnes.The following table documents the imported quantities on the most important industrial minerals.

Jan 1, 1989

By Membrey W. B, Partridge A. C

Lower transportation costs, improved handling and better utilization efficiency are some of the reasons that make low moisture coal product desirable. There has been considerable interest in the development of effective coal dewatering techniques to achieve this result. One avenue of considerable merit for enhancing dewatering processes is by modification of the surface chemistry of the coalwater slurry system by chemical means, resulting in better performance of existing equipment. This paper reports the results of an investigation of the utility of surface active agents in the enhancement of fine coal dewatering. A large variety of proprietary dewatering agents have been studied in relation to their efficiency in enhancing the dewatering of a number of Australian coals. Properties of particular coals that make them amenable to improved dewatering by particular chemical agents have been identified. Surface studies, including surface tension and zeta potential measurements as a function of surfactant concentration, as well as dewatering assessments, were used. Particular attention was paid to filtration, but the results could be applied to other dewatering systems.

Jan 1, 1989

In the Massif du Sud ophiolite complex platinum group elements occur predominantly as ultrafine-grained inclusions of rutheniridosmine, laurite and iridosmine. These form primary inclusions less than 5 to 10 um in diameter within chromite in podiform chromitite fringed by dunite, and emplaced subsequent to solidification of the host harzburgite. There is no specific association with trace inclusions of transition metal sulphides. The crystallization of then: Ir. Os and Ru minerals may have occurred concomitant with hromite, perhaps related to more reducing conditions produced by crystallization of the chromite. The Ir, Os. and Ru show pronounced fractionation from Pd, Pt and Rh expected to be also present in the mantle source rock. The dunite shows evidence of metasomatic origin from adjoining harzburgite, and the possibility of selective crystallization of the Ir sub-group elements suggests that Pd, Pt and Rh may have been transported elsewhere.

Jan 1, 1989

By Collier D

The topaz resource at Torrington in northern N.S.W is currently the subject of a joint research and development programme managed by Pacific Copper Ltd, This programme has culminated in a pilot topaz calcination plant, located at Parramatta, which, through its operation, will establish the commercial viability of developing this mineral as an industrial raw material for both the refractory and fluoride chemical industries.

Jan 1, 1989

Project developent proceeds by increasingly detailed studies addressing overall project returns through an analysis of the substance, risks and costs associated with the following elements: ò Reserves ò Mining ò Processing ò Infrastructure ò Environmental Impact ò Product Market Computer-based expertise has a potential to ò Capture perishable expertise, making this available for shared access and so reducing the cost of human experience ò Consolidate know-how for optimising process operations, bringing consistency of judgement and advice to decision- making by making the rules, facts and preferences explicit ò Allow assignment of the basis and authority of decisions, so experts can pass routine expertise down the line, freeing their time to generate more. ò Force a review of expertise when creating the knowledge base.

Jan 1, 1989

By Mansor A. N

Results are reported for the computer simulation of heap leaching of mixed copper oxide and sulphide ores. They resemble those obtained from testwork in terms of a substantial peak in the copper concentration of the pregnant solution, an initial period when no copper emerges and a lengthy period towards the end when the copper concentration and the daily increment in copper recovery are low. The simulation can be used to forecast process results before any column or similar testwork is performed. Potential applications of the simulation to process design, operating strategy and optimisation are discussed. Three modes of operation are identified that correspond to different performance patterns and dependencies on ore and process variables. The relative merits of different operating strategies for approaching the ideal performance are being investigated. For process design and development purposes, the simulation may be used with a limited testwork programme to achieve significant savings in time and resources.

Jan 1, 1989