Search Documents

By John D. Carr

Introduction The Flin Flon zinc plant operates on what is known as the low density or standard sulphate process, that is, the zinc is carried through the plant solution circuit attached to the SO4 or sulphate radical at a concentration not exceeding 175 grams per litre zinc. The process may be described briefly as follows: The zinc is received in the zinc concentrate chemically combined with sulphur and mixed with many other impurities. The concentrate is roasted and most of the sulphur is burned to a gas, which is discharged from the plant. The roasted concentrate, or calcine as it is called, is leached with a weak sulphuric acid solution so that the resulting leach solution contains a high zinc content but a very small proportion of the impurities. The solution is separated from the solids and is purified further by agitation with zinc dust to remove copper, cadmium, and cobalt. This purified zinc sulphate solution is then pumped to the electrolytic department. The solids from the first leach are again leached, but this time with a stronger acid solution to dissolve all of the remaining zinc which is soluble in the strength of acid available. The solids and solution from the leach are then separated. The solids are stock-piled for further treatment at some future date and the solution, carrying a relatively high amount of impurities, is sent to the first leach, where the chemical action is such that the contained impurities are precipitated as solids. The electrolytic department is nothing more than a large number of electroplating cells in which the zinc is plated on aluminium sheets. Since zinc does not plate tightly to aluminium, the zinc plating or sheet is easily stripped from the aluminium and the sheets are collected to be melted and cast into the standard market bars or slabs. In the electro-deposition cells, the zinc sulphate (ZnS04) is split to metallic zinc (Zn) which plates out, and sulphate (S04) which combines with the hydrogen of the water of the solution to form sulphuric acid (H2S04). When one pound of zinc is deposited, about one and one-half pounds of sulphuric acid are formed. This acid is sent to the leaching section, where it dissolves one pound of zinc from the calcine. The solution is purified and is again pumped to the plating cells. The solution travel forms a complete circuit.

Jan 1, 1935

By F. F. Langford

"The Athabasca Basin occupies about 100,000 km2 of the northwest corner of Saskatchewan with its western margin extending about 50 km into Alberta (Fig. 1). The basin is filled with a Helikian sequence of predominantly fluvial sandstones up to 1600 m thick. The sandstone beds are generally flat-lying, and rest unconformably on a crystalline basement which consists mostly of granitic intrusive complexes and quartzfeldspar- biotite gneisses. The basement rocks represent Aphebian sediments and Archaean basement rocks that were metamorphosed and remobilized to varying degrees during the Hudsonian Orogeny (ca 1800 Maj.Since 1968, three mining camps and several substantial unconformity-type uranium deposits have been discovered in the area (Figs. 1 and 2). These deposits lie along the unconformity surface, partially enclosed in sandstones, and partially in the basement rocks. The major deposits have elongate, pencil shaped orebodies that are parallel to the strike of underlying graphitic biotite gneisses. The total tonnage of uranium is in the order of 150,000 to 200,000 tonnes and mining grades range from 0.5 to 2.5 per cent U3O8.IntroductionUranium exploration started in Saskatchewan in 1945 when Jolliffe and Murphy headed field parties to investigate uranium occurrences on the north shore of Lake Athabasca (Kupsch, 1978). Their investigation lead to the development of the Beaverlodge camp in the following years. Some of the early prospectors were impressed by the fact that the uranium occurrences at Beaver lodge were centred on a thick sequence of unmetamorphosed arkosic redbeds which are now called the Martin Group. This sequence was referred to as the Athabasca Series by Christie (1949), and although some occurrences of uranium were found near Stony Rapids and Black Lake, the vast expanse of Athabasca sandstones south of Lake Athabasca was generally regarded as unpromising."

Jan 1, 1986

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By R. B. Nourse, S. F. Gwynn-Jones, S. Nikolic, M. L. Bakker, I. McDougall, H. Joubert

"Tenova Pyromet’s core furnace knowhow and expertise has been built within the ferroalloy and nickel/platinum group metal (PGM) industries with the supply of electric furnaces for a number of nickel/PGM operators, including Eastplats, Lonmin, and Anglo-Platinum in South Africa, Mineraçào Serra Da Fortaleza in Brazil, and Norilsk Nickel in Russia. Tenova Pyromet has also supplied the electrode columns and associated electrode equipment – the heart of the electric furnace technology – for cobalt recovery in furnaces in Zambia and the Democratic Republic of the Congo. The quantity and size of projects undertaken by Tenova Pyromet has provided the opportunity to continuously improve furnace designs and the scope of supply, culminating in the most recent nickel/PGM project currently under construction at Northam Platinum. Through this innovative culture, the Tenova Pyromet Base Metals Initiative was formed in 2015 to develop the Novasmelt™ Furnace; a next generation optimised Top Submerged Lance (TSL) furnace design. The combination of Tenova Pyromet’s advanced Novasmelt™ product with our industry leading electric furnace technology are discussed with reference to applications for nickel and cobalt production. Flowsheet arrangements are compared summarising potential capital savings, operating requirements and achievement of downstream product quality.INTRODUCTION Tenova Pyromet is a leading player in the field of smelting technology development and equipment supply. Tenova Pyromet is the result of the union of three furnace suppliers under the Tenova banner: Techint Technologies (Tagliaferri), Core Furnace Systems Corp (Lectromelt) and Pyromet Technologies. The furnace experience of the combined groups dates back over a century with the earliest Lectromelt going into production in the early 1900s. Throughout the modern era, Tenova Pyromet has developed a reputation for providing dependable innovative smelting technology, high quality equipment and sound project execution to a worldwide client base with customer plants operating in Europe, Southern Africa, North America, South America, Russia, Kazakhstan, the Middle East, South Korea, and India. Tenova Pyromet’s core knowledge and expertise was developed in the South African ferroalloy, base metals, and platinum group metals (PGM) smelting industries. Tenova Pyromet has spent considerable effort on development and has contributed significantly to improve the state of the smelting industry. Tenova Pyromet’s electrode columns have become widely renowned and are now providing significant benefits, especially in increased furnace availability, to many smelting furnace operators. The electrode column is the heart of the furnace as it delivers a controlled amount of electrical energy, at an optimum depth in the burden/bath, to the smelting process. Every furnace is custom designed to the specific operating range and optimal operating point of that furnace and process"

Jan 1, 2017

?Introduction to the Delphi Group ?Why is carbon important to your organization ?Key elements of a carbon management strategy ?Inventory ?Risk & opportunity scan ?Mitigation options and financial mechanisms ?Identify targets and develop policy ?Communication and improvement ?Manage for success

May 1, 2009

By A. D. Fisher

This paper describes the future position of metallurgical coal, particularly as applied to Canadian reserves. Quality coking coal is declining in availability, but preheating practices may alleviate this situation to some extent. Two new processes are discussed in the paper - formed coke and direct reduction - and their coal specifications are outlined.

Jan 1, 1972

By A. Deneys

This paper reviews industrial gases used in primary copper production. Copper smelting industrial gas demand has steadily increased since the first commercial oxygenconcentrate smelting in 1952 [1]. In copper production oxygen for smelting is the dominant industrial gas use followed by oxygen for converting. Nitrogen is finding increased use in copper smelters. Nitrogen is used for porous plugs for copper converting and anode refining [2-5]. Nitrogen can be used for concentrate drying [6,7] and is also used in some Ni-Cu smelters as a coolant in Peirce-Smith converting [8,9]. Industrial gas supply options of cryogenic or adsorbent based on-site plant or cryogenic liquid delivery are detailed.

Jan 1, 2007

By R. Liu

As Building Information Modeling (BIM) becomes widely adopted by the construction industry, it holds undeveloped possibilities for supporting Facility Management (FM). Some FM information systems on the market claim to address the needs for FM requirement. However, the question of whether the functionalities provided by the current BIM-based FM software companies are those actually required by the FM Professionals still need to be answered. The data is required by FM professionals in the operation and maintenance phases of facilities and type of maintainability problems that frequently occur, which can be solved early in design phase, have not yet been addressed. The aim of this paper is to clarify the frequently occurring maintainability problems and to investigate the potential areas that can use BIM technology to solve the maintenance problems in early the design phase. A survey was conducted to collect perspectives from the industry practitioners for the maintenance problems and their frequency. The survey results indicated that maintainability considerations should be taken into consideration during the facility design phase. The results also address the perceived areas by practitioners that need maintainability consideration in design phase

Aug 1, 2013

By J. O?Shea

From the characteristics of the new (1976) electronic components and units that are being marketed, the author has tried to foresee the types and the performances of the near-future slope-monitoring equipment. Much-improved sensors, instruments and systems for pit use can now be developed - sun-powered telemetry remote stations are feasible, very sensitive as well as precise and drift-free liquid level inclinometers will be available, new techniques for distance measurement with lasers obviate the need for atmospheric corrections and the latest generation of desktop calculators have become easily programmed minicomputers. Thus, it is realistic to assume that fully automatic pit-slope monitoring systems will be operational in the foreseeable future.

Jan 1, 1978

By A. Consigny

New "clean technologies" to treat mining and metallurgical effluents containing dissolved metals have been successfully applied at mine sites in North America and Asia, treating water flows up to 24,000 m3/day. These clean technologies offer significant benefits compared to conventional alternatives and provide a sustainable solution that eliminates residual waste sludge, improves water conservation, generates revenues from wastewater, and delivers overall improvements to the environment. This paper will profile these technologies, and provide best practice case study examples of their application at mining operations, including data for water chemistry, flows, water quality, capital and operating costs, and life cycle costs of treatment.

Jan 1, 2011

Productivity and efficiency of diesel-powered underground trucks and LHDs can be enhanced through the application of a range of advanced technologies. In addition, these machines are subject to ever more stringent emissions control requirements. This paper will review how various technologies can improve usability, maintainability, and performance of LHDs, through a number of examples. The use of instrumentation and monitoring to understand the role of operator practice on mucking efficiency, as well as the use of finite-element analysis to evaluate structural design, and the use of control techniques to modify operator inputs and hence decrease power consumption, will be presented.

May 1, 2002

By Robert G. Boutilier

So far, most social performance monitoring systems have not gone beyond listing the impacts on various stakeholders. Executives have had to rely on intuition to devise interventions that would improve the impacts. This paper describes a survey process, known as the Stakeholder 360 (S360), which eliminates much of the guesswork. The paper reviews key studies showing that raising the levels of communication, trust, and common vision among stakeholders leads to the acquisition of the resources needed to improve the socio-economic situation. Therefore, the Stakeholder 360 measures the levels of these three factors in the relationships between a company and its stakeholders, and among the stakeholders themselves. In a validation study at a gold mine in rural Papua New Guinea, the S360 produced a socio-political ?roadmap? that showed management and stakeholders alike which relationships need more communication, trust, or common goals/vision. Management used the findings to create alliances that helped the government move forward on a regulatory regime for the mine closure. The community used the findings to focus its planning for life after the closure. An S360 survey conducted six months later revealed a decline in dependence on the mine and an overall increase in levels of mutual understanding.

May 1, 2002

By Garston Blackwell

Abstract - During geostatistical estimation of block grades, the kriging process produces a measure of error, the kriging variance or the kriging standard deviation. Estimation of the block error depends on the semi-variogram model for a deposit, which reflects fundamental characteristics of a deposit such as (1) nugget effect, (2) range of influence of grades, (3) different local spreads of data as a function of average grade (proportional effect), (4) nested structures, and (5) underlying anisotropies in the data; this model may be affected by sampling or assaying limitations, however. Because the kriging error incorporates so many features of both the deposit and data to be used for estimation, it may offer a substantial improvement on block classification over traditional procedures such as data density. Practice indicates that the relative kriging standard deviation (RKSD) is particularly useful for block classification in measured, indicated and inferred categories. Plots of RKSD in plan and section also can be used to demonstrate where extra drilling and sampling would be most advantageous for upgrading the class of some blocks. Moreover, the use of grade and RKSD filters can show where material near cut-off grade is poorly defined, indicating sampling target areas to improve block classification in the vicinity of the ore-waste boundary.

Jan 1, 1998

By N. Staroselsky

"Significant energy savings are often possible for centrifugal compressors operating in parallel by improved control strategy and improved instrumentation. Blow-off can usually be reduced by improved surge control combined with a better control strategy for loading and unloading the group of machines. More precise and stable pressure control then becomes possible. This improved control strategy will also decrease the frequency of operation near the dangerous limits of surge or overload or overspeed. A sample station of mixed centrifugal and reciprocating compressors is examined and a substantial energy saving with the recommended control strategy is projected from operating data. Present Operating Conditions of the Compressed Air StationThe Compressor StationThe compressor station described here has three centrifugal compressors and three reciprocating. It supplies a mine in New Brunswick.Compressed Air and Power ConsumptionFigure I and Figure 2 provide graphs of air consumption and pressure changes based on the owner's data.During the typical two-shift operating day (Fig . I) in the non-productive shift (midnight to 8:00 a.m.), the consumption stays at a level of 9,000 SCFM. This corresponds to a pressure of 110 PSIG. Then, after 8:00 a.m ., the air consumption starts to increase and th e pressure decreases. Around 10:00 a.m., the consumption reaches its maximum level at 97 PSIG. Around II :30 a.m., the air consumption starts to decrease because of the production drop during the lunch break of the first shift. Pressure increases again up to 109 PSIG. After the break, consumption rises to its maximum level over 16,000 SCFM andpressure drops to 97 PSIG.Around 2:30 p.m., the air consumption drops sharply to 9,000 SCFM because of the production decrease to zero level. This drop results from changing of shifts. The pressure at this time increases again up to 110 PSIG. The second shift (2:30 to II :30 p.m.) is an alogous to the first.During the three-shift operating day, the break around 4:00 . a.m . and the shift change around 6:30 a.m. cause sharp drops in air consumption. The pressure for almost the entire night shift stays near 110 PSIG because the station is working with blowing-off even under the maximum consumption. The analysis of Figures I and 2 shows that the pressure varies with the air consumption changes. During non -productive time (non-production shifts , shift changes and breaks) or during the night shift, the total station capacity is proportional to the discharge pressure. By decreasing the level of this pressure up to 97 PSIG, the flow of the station may be decreased during the non-production time as follow s:"

Jan 1, 1980

By S. Jain

Construction industry is considered as labour intensive, having shortage of skilled labour, unsafe with large number of industrial accidents. Construction industry requires high technology automation products (Robots) for improving productivity, safety, quality etc. Robots are developed by various countries in different areas like demolition, earthwork, bridge, tunnels, road work, underwater works, trenches and piping, maintenance etc. however they are still not used to their full potential by construction industry. Hence in this paper, the authors propose a ?model for adoption? of robots in construction industry. This model considers how a construction firm will adopt full scale robots like manually controlled machine, tele-controlled machines, computer controlled machines and cognitive robots and assimilate them through various stages.

Aug 1, 2013

By R. Dawes, B. R. Davis, T. LeBel, C. Pelow

Settling of copper, lead, and other metals in slags is an important part of overall recovery of metals, both in primary and secondary operations. The impact of slag reduction on settling is not well known. This is important since the cycle time for slag cleaning can be significantly changed with reduction of slag, through a decrease in slag viscosity and growth of metal/sulphide particles. KPM has worked with a number of primary and secondary recyclers to better understand how reduction of slag can improve overall operation. In this presentation, we describe the type of test work and analysis done and how this information can be used to guide improvements in metal recovery from slags. INTRODUCTION Typically, copper smelter slags contain about 1-2% copper, both in the form of copper and copper sulphide beads and dissolved copper oxide in the slag (converter slags are recycled to the smelter). With the average grade of world copper deposits close to 0.7%, it is practical to recovery copper from these slags. This is done routinely by one of two methods. The first method uses slow cooling in large ladles or beds to grow particles of copper sulphide. The slag is then crushed, milled, and floated for copper recovery. The slow cooling promotes precipitation and growing of the sulphide particles from the solution and then, the slag can then be milled to recover the copper through froth flotation. A consideration of this process includes the energy cost related to grinding, the use of water, capital cost for ladles, and the availability of tailing dumps. At the same time, the retreatment of the Cu concentrate produced in the mill will displace fresh concentrate, which ultimately results in a reduction of the throughput. The second method is the so-called “slag cleaning” and is based on the settling of copper and copper sulphides particles dispersed in the slag. This is achieved by decreasing its viscosity by increasing the slag temperature and reducing the iron spinel solid phases (magnetite) that increase the apparent viscosity of the slag. Typically, the reduction does not extend to the reduction of copper, and soluble copper (mainly as oxide) and fine matte particles remain at concentrations typically at or above 0.5% (Cardona et al., 2011; Cardona, 2011). This is an improvement on 20 years ago when slag was sent to dumps at 1% or less (Demetrio et al., 2000).

Jan 1, 2019

By Esau Arinaitwe

The most extensively used methods and approaches for characterizing and selecting frothers for plant application are based on measurements in clean water in the absence of solids and without consideration of physicochemical factors that are known to influence the properties and behavior of practical flotation froths, and hence metallurgical performance. These factors include aquatic chemistry, collectors, modifiers, particle shape and size, and pH. Understanding interactions between these factors and the role and relevance that they play in characterizing frothers and froth zone properties will greatly aid in the frother selection and evaluation process. Such an understanding will also greatly enhance the ability to create frother solutions that are sufficiently robust to plant variability (such as mineralogical, comminution, operational, physical and chemical). This paper reports results of a “systems approach” study designed to probe ways in which physicochemical factors a) influence frothing and bubble size in 2- and 3-phase systems, and b) confound correlation of fundamental measurements with flotation outcome. The concepts and insights gleaned from fundamental frother studies, together with empirical laboratory flotation tests and a thorough understanding of plant needs and challenges were used to develop and implement customized frother formulation at a Cu-Mo flotation plant. Plant metallurgical data and qualitative assessment of froth zone properties showed that a frother formulation developed using the approach described here provided marked improvements in froth characteristics (mineralization, mobility, stability, persistence). These improvements resulted in better circuit control and significant performance advantages, such as improved coarse particle recovery, without detrimental downstream effects. INTRODUCTION Successful recovery of value minerals of sufficient grade via the flotation process requires selective manipulation of the value minerals to render them hydrophobic using collectors and modifiers. The hydrophobized minerals then attach to air bubbles and the mineral-bubble aggregates are selectively transported through the froth zone into the launder. Frothers play a critical role in froth formation and more importantly in achieving and maintaining desirable froth characteristics (for example, stability, mobility, persistence) that are essential in facilitating the selective transport and recovery of value minerals. Fundamentally, frothers contribute to the transient stability of thin liquid films and so aid in reducing bubble coalescence rates in the pulp and froth zones, thus maintaining the small bubbles required for efficient bubble-particle attachment. Invariably, the action of frothers at the liquid/gas interface in the pulp and froth zones impacts bubble stability, water and solids transport to the froth, which in turn impacts froth mobility, froth carrying capacity, and the concentrate grade. Consequently, selection and evaluation of frothers for flotation plants requires careful consideration of the frother type, though the choice is limited to only two main classes of compounds in terms of fundamental chemistry (short chain alcohols and polyglycols). Even with the selection of what is thought to be the best frother for a given application, practical knowledge of the froth zone and experience in controlling its properties is essential for maximizing metallurgical performance.

Jan 1, 2019

By Z. Tang

A collaborative project was performed between NRC Institute for Fuel Cell Innovation and MagPower Systems Inc, to develop a cost effective fabrication process to manufacture the anode for magnesium-air fuel cell with improved performance. A novel fabrication process was developed, which resulted in a porous microstructure with increased surface area, instead of the traditional solid structure. This porous anode greatly increased power density in the magnesium-air power source. This fabrication process is very simple and cost effective. Especially, this process makes it convenient to incorporate different alloying additions, as well as hydrogen inhibitor and electrolyte management additive into the anode. The anode composition was designed so that micro galvanic cells were formed as current is drawn out of the fuel cell, and resulting increased dissolution rate of Mg. It is feasible to incorporate hydrogen inhibitor and electrolyte management additive into the porous anode, and the anode with some kinds of inhibitors exhibited improved electrochemical performance. This paper describes the microstructure and electrochemical performance of anodes with designated porous structure and alloying additions. Furthermore, quantitative kinetics analysis of the obtained I-V curves and electrochemical impedance spectroscopy were carried out to clarify the mechanism.

Jan 1, 2005

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

By A. M. S. Hussein, B. E. Rogers

Progressively more stringent emission limits and advances in regulations and enforcement have made air compliance more difficult for metallurgical facilities. This has historically required improved collection and treatment of stack sources. Fugitive emission reductions are now increasingly required to achieve compliance. Typically small in magnitude, fugitive emissions have a disproportionate impact on ground level concentrations, can be visible to the public and can influence workplace health and safety. Moreover, these emissions are complex, as they are spread over multiple sources, distance and time and are affected by various activities and conditions. As such it is difficult to find, define and monitor these emissions and their impacts. This difficulty translates to the design of emission reduction measures and operational requirements. This paper presents an overview or ‘heuristic’ of fugitive emissions management for compliance in existing operations. This includes aspects such as the impact of regulations on project scope, approaches to developing a comprehensive emission inventory, considerations for solution development and the plant’s role in sustaining compliance once achieved. Case studies are presented to demonstrate how portions of this approach have been applied.

Jan 1, 2015