Search Documents

By D. Berkley

Off-gas systems often become the limiting factor in production increase and environmental projects. Any upgrade or new off-gas project needs to address control instability issues, instabilities that can result in safety hazards, significant loss of system capacity and/or emissions to the environment [1]. In addition, the design engineer must optimize system configuration and equipment size for the new operating conditions, to have a technically feasible and economically viable project. Dynamic simulations can be used for addressing both the control stability and the design optimization issues. This paper illustrates how the dynamic simulation of transient processes and of their control system can be used in "real life" situations for these purposes, presenting the example of an electric furnace off-gas system design.

Jan 1, 2005

By J. A. Espinosa-Guillen, J. A. Lopez-Molina, S. García, J. A. Valencia-Quintanar

"The design and implementation of grouting treatments in rock masses are procedures that require continuous adjustment of parameters and criteria to optimize the results. In this proposal we describe a set of tools that enhance decision-making for this type of jobs particularly in dam projects. The methodology is focused on hydrogeological zoning of the site and its constant update combining engineer’s experience with artificial intelligence techniques to integrate the site knowledge; as well as the evaluation of grouting results for different scrutiny scales, with special attention on the relationship between water absorption and grout consumption. INTRODUCTIONSeveral methodologies for design, implementation and evaluation for grouting rock masses have been developed for the solution of specific problems and tested in diverse geological conditions. Each of these methodologies is focused on results evaluation for different scrutiny scales (Table 1) and is employed to assist decision-making before or during the grouting process.Some methods define specifications for grouting each stage of the borehole, making theoretical, semi empirical or experience-based considerations to define basic parameters as maximum pressure, maximum volume, grouting time, flow rate, etc. Ultimately each approach aim to optimize the injection process, adjusting volumes or the grouting time required to obtain satisfactory results, reducing risk of creating new flow paths or unnecessary grout travels, and enhancing the mixture properties to achieve adequate penetrability and long-term behaviour. Some of these criteria have been widely used in dam projects, for example the concept of Grouting Based on Facts to define the maximum pressure and volume (Ewert, 1997), the GIN method (Lombardi & Deere, 1993; El Tani, 2012), or the North American standards based on Apparent Lugeon measures (Naudts, 1995; Bruce 2011); on the other hand, there are relatively new criteria that have shown good results for dam grouting as the Aperture Control Method (Bonin et al., 2012; Carter et al., 2012) or the Real Time Grouting Control Method (Stille et al., 2012)."

Jan 1, 2015

By Rayleen Riske

Why do we look for better reconciliation when times get tough? Why wait? Mine reconciliation should be a priority throughout the good times too. In fact, with good reconciliation, those good times are going to be even better and will help pave the way to success through those preventable bad times. Reconciliation throughout the entire mining value chain requires the capture, validation, and analysis of copious amounts of data. This task can be daunting for a team in a small mine, let alone reconciling across a suite of large mines. This paper will outline the different ways we can reconcile across the value chain, why we should reconcile over differing periods of time and how Snowden?s solution to proving reconciliation can be a simpler, reliable and transparent process. Snowden?s Reconcilor is proving to be a valuable tool on any mining scale, by capturing, validating, sorting and reporting data for timely decision making by the site geologist through to corporate management. By instigating vigorous reconciliation, you are setting your mine up for the future. Not only will you have the means to analyse your current processes and measures, but you will have the opportunity to identify and improve your mine?s performance from the resource model through to the final product.

May 1, 2010

By Y. Mitsuda, Y. Kayanuma, T. H. Okabe, M. Miyake

A new process to recover platinum group metals (PGMs) from automotive catalyst scrap using metal vapor was developed. To improve the efficiency of the acid dissolution process of PGMs, metal vapor of reactive elements such as magnesium or calcium were contacted with spent automotive catalyst. It was expected that metal vapor would react with metal selectively and form intermetallic compounds. The specimen of the spent catalyst was treated at 1173 K for 3 h, and it was then dissolved in aqua regia for 1 h to recover PGMs. After the reactive metal treatment, 88% of Pt, 81% of Pd, and 72% of Rh in the catalyst scrap was dissolved, while only 77% of Pt, 69% of Pd, and 38% of Rh was dissolved from untreated scraps.

Jan 1, 2004

By R. W. Culley

"In many areas of Saskatchewan, known gravel deposits have been depleted or are diminishing rapidly; in other areas, particularly in the north, demands for all-weather highways and access roads are far exceeding the supply of gravel sources with which to surface them. These two problems have made conventional methods of air-photo and ground surveys insufficient for gravel location. In the first case, hauling costs on construction now warrant searching for buried deposits and for smaller, less obvious surficial deposits that may be closer to the project. In the second case, search and access conditions are so difficult and costly that the ratio of successes to failures must be kept very high. The Department of Highways has long been aware of the oncoming scarcity of quality gravel deposits and is continually investigating ways of forestalling it. One of these ways is the use of airborne geophysical methods that permit rapid coverage of large areas and that sense and discriminate between earth properties to a significant depth below ground surface. In 1967, the Department began an investigation of an airborne conductivity survey method called INPUT*, or ""Induced Pulse Transient'', leading to a trial in 1968 and data analysis in 1969. The results of this trial initiated• modifications to the technique to improve its sensitivity for mapping shallow deposits. Part way through this modification in 1970, a decision was made to change to an airborne resistivity survey method called EPHASE*. Trials with this technique were conducted and analysed in 1971. This paper is an explanation of the E-PHASE system and a summary of the results from one of three areas mapped in 1971."

Jan 1, 1973

By Julia Pflieger, Manfred Russ, Johannes Gediga

This paper shall show an economic feasible approach to implement Greenhouse Gas (GHG) reduction measures into the mining and metallurgy industry. The goal to improve energy consumption is directly linked to the reduction of GHG emissions and therefore directly in correlation with the economic viability. A baseline scenario of the considered reference system and of the respective reference year has to be defined, mapped and analysed. In a second step an analysis of the same operation using available and prospected Best Available Technology (BAT) processes is carried out to generate a basis for a benchmark system. The identified reduction potentials are reported and the GHG emission reductions are put into relation to the investment cost of the new process technologies / process adaption to be implemented. This economic feasibility calculation is necessary to realise a cost efficient GHG reduction roadmap implementation into the company's business operations. The GHG reduction roadmap is developed using ratios between GHG reduction and investment / operating cost to get an indication for a sequence for implementing carbon emission reductions measures.

Jan 1, 2010

By T. C. Cheng, G. P. Demopoulos

It is the object of this paper to discuss various options for improving the hematite process in terms of increased throughput hence lower capital cost and production of saleable quality hematite. With reference to increasing the throughput of the process, it has now been determined via the analysis of Akita Zinc Co's continuous industrial autoclave performance data that the process kinetics is limited by the rate of the hydrolytic precipitation reaction. By correlating the hydrolytic precipitation rate to supersaturation ratio, it is shown that accelerated kinetics can be achieved via the following measures: (1) in-situ neutralization with addition of zinc calcine; (2) elevation of temperature; and (3) dilution of feed; of which, the first one was retained for further evaluation. According to presented estimates, addition of calcine, amounting to only 2.6% of the total zinc calcine processed, can allow for shortening the retention time by at least 50%. Such drastic shortening of retention time may be either used to increase the throughput of a given autoclave circuit or alternatively to release autoclave capacity for clean hematite production. Hydrothermal treatment of the crude hematite product proved effective in producing clean hematite as according to laboratory tests, hence allowing the sulphur content of hematite to be reduced from around 4% to less than 1%. A conceptual flowsheet incorporating in-situ neutralization for accelerated kinetics with hydrothermal upgrading of crude hematite without sacrificing production capacity and with minimum upset of the plant's water balance is described.

Jan 1, 2004

By L. Xia, B. Hart, K. Douglas1, S. C. Chelgani

Development work to optimize a flotation flowsheet for rare earth element (REE) recovery is underway. The original approach used alkyl phosphates and phosphoric acid ester as collectors to concentrate REE minerals. To improve REE recovery, hydroxamates as alternative collectors were investigated. In this paper, micro flotation of REE minerals using salicylic, benzoyl and naphthoyl hydroxamates is reported. Unlike phosphonic collectors, slime removal does not show a significant effect on REE recovery when using hydroxamates as collectors. Among the three hydoxamates, the grade of La, Ce, and Nd for concentrates produced by salicylic hydroxamate is the highest. The recovery response with naphthoyl hydroxamate is similar to that of salicylic hydroxamate; good grades for La, Ce, and Nd, less effective for Nb, Y, and Zr. The data indicated an affinity by salicylic and naphthoyl hydroxamtes for LREE over the HREE minerals. In comparison, benzoyl hydroxamate indicated an affinity for Nb, Y, and Zr. Temperature effects on REE recovery were also studied. The grade and recovery of REEs generated by flotation using a mix of salicylic and benzoyl hydroxamates at room temperature was almost identical or even better relative to the recovery using naphthoyl hydroxamates at elevated temperature.

Jan 1, 2014

Cansolv® S02 Scrubbing Technology was described in a paper in Copper/Cobre 03. Four years on, the technology is operating at a full scale production facility.Hindustan Zinc Limited expanded their capacity by installing the AUSMELT process. The process proceeds through smelting, slag reduction, slag cleaning and holding stages sequentially in the same vessel, resulting in widely varying off gas characteristics. The off gas is suitable for treatment is a conventional acid plant for a modest proportion of the day, but at other times produces off gas too high in S02 to be discharged to atmosphere. Cansolv® S02 Scrubbing Technology was identified as a means of effectively removing the S02 down to low levels from the off gas during all stages of the pyrometallurgical process. Furthermore, the Cansolv® S02 Scrubbing System Technology produces high purity S02 that allowed for the captured S02 to be directed to an existing acid plant, avoiding the capital cost of new acid making capacity.

Jan 1, 2007

By Richard J. Kolada, Ian R. Muirhead

"This paper reports on a CANMET-funded examination of less conventional underground coal mining methods. These methods are documented and those that show the most promise for application to western Canadian conditions are discussed in detail.IntroductionIn recent years, mining considerations and economics have encouraged a transition from underground mining to surface mining. However, a change in market conditions or the development of superior underground mining methods may reverse this trend . Should this happen, the industry must be quick to respond and have information available on the latest developments of underground mining technology. In time, deposits of high-quality coal, which are easily accessible to surface mining, will be depleted and a change to underground mining methods will require consideration. The economic transition point between surface to underground will be a major determinant in maintaining a competitive edge. For these reasons, it is important to keep abreast of improvements in underground mining methods. To meet this objective, CANMET awarded a research contract to Monenco Consultants Limited, to investigate unconventional underground mining methods that show a potential for western Canadaoi. This paper presents the results of this investigation."

Jan 1, 1988

By P. H. Willis

Since the 14th CMMI conference, held in Edinburgh in 1990, at which a paper was presented by the author (Willis, 1990) reviewing the role of integrating new technology as a survival strategy for South African gold mines, considerable change has occurred in the South African mining industry. This paper reviews the current state of the industry and provides an update on the technologies discussed ten years ago. It reviews available technology and provides a broad economic assessment of these technologies if they were to be introduced in an integrated mining system with a focus on deep level mining below 3000 m. It also reviews possible future technologies currently being researched and developed by CSIR: Division of Mining Technology (Miningtek).

Jan 1, 2000

By M. Gyenge, O. F. Coates, K. Barron

"It is suggested that artificial supports might be used to increase, with safety, the angle of hardrock open-pit slopes. Guidelines for designing such a support system, based on a simplified analysis, are given. The installation, construction and instrumentation of a trial support system is described and a breakdown of the construction costs is given. On the basis of this cost analysis, the economic benefits derived from reduced waste-rock excavation are compared with the support costs for a typical mine. In an example, it is shown that the slope angle in an open-pit mine 500 ft deep, with benches 50 ft high by 30 ft wide, could be safely increased from 37Yz degrees without support to an optimum of 53 degrees with support. In this case, the support costs would be approximately $900 per linear foot of pit wall and the savings due to decreased excavation of waste rock (at $0.34/ton) would be approximately $1,900 per linear foot, yielding an increased margin of profit of approximately $1,000 per linear foot of pit wall. This figure could be increased to $6,000 per linear foot if the steeper slope were used to extract more ore.More than 50 per cent of the support costs are accounted for by diamond-drilling the holes for the deep cable anchors. The use of percussion drills for this purpose would seem to offer a means of significantly reducing the support . costs and thus further increasing the profit margin available."

Jan 1, 1971

By W. J. Li, L. Kong, G. L. Li, X. M. Xi, J. Qiu

"A novel hydrothermal method was applied to prepare the precursor of LiMn2O4 using pre-treated electrolytic manganese dioxide (EMD) and lithium hydroxide as the main raw materials. The precursor was subjected to heat treatment between 400 and 900ºC to obtain spinel Li1.05Mn1.95O4 and Li1.035Co0.035Mn1.930O4 positive materials for lithium ion batteries. The structure and morphology of the obtained powder materials were studied in detail by means of X-ray diffraction (XRD) and scanning electron microscope (SEM). It is found that the precursor has an amorphous structure and a high reactivity, which is easily transferred to spinel structure during heat treatment, obtaining a positive material with an uniform structure and good performances. The XRD patterns reveal that single phase spinel Li1.05Mn1.95O4 can be obtained from the precursor after heat treatment at 600°C in air. The final Li-rich Li1.05Mn1.95O4 product obtained showed a well-defined stable spinel structure and distinctive crystal faces with particle size between 200 and 300 nm. The as-prepared Co-doped spinel sample exhibited a excellent electrochemical performance with an initial discharge capacity of 113.0 mAh/g and 93.8% of its original value was retained after 100 charge-discharge cycling at 0.5 C.INTRODUCTIONThe increasing demand for portable electronic devices and hybrid or full electric vehicles is driving the development of cheap, efficient, compact lightweight and environmental friendly rechargeable batteries systems (Chung et al., 2002; Scrosati, 1995). Lithium ion secondary batteries have satisfied this demand to a greater degree than other battery systems. The cathode material plays a critical role in the performance of Li-ion batteries. The high cost and toxicity of cobalt compounds for the cathode material of LiCoO2 has prompted a search for alternative materials. LiMn2O4-based spinels offer a potentially attractive alternative to LiCoO2, due to its abundance, low price, ease of preparation, environmentally friendly characteristics, better thermal stability, and its effortless recycling (Tarascon et al., 1991; Yabuuchi and Ohzuku, 2003; Amatucci et al., 1999; Tsai et al., 2003). Some achievements have been created to meet the requirements (Guo et al., 2010; Kang et al., 2005; Park et al., 2008; Takahashi et al., 2006; Lee et al., 2001; Yoshio et al., 2001; Arumugam et al., 2008). However, the largest obstacle encountered in the practical applications of LiMn2O4 is its fast capacity fading during long term cycling, which is due to Jahn-Teller distortion of the [MnO6] framework, the electrolyte decomposition at high potentials and manganese dissolution into the electrolyte (Fey et al., 2003). The electrochemical performance of LiMn2O4 is also strongly dependent on its morphological properties, such as crystallinity, phase purity, surface area, grain shape and particle size distribution, etc. All these morphological properties are closely related to the material synthetic routines and heat treatment processes (Huang et al., 2000; Myung et al., 2000; Takada et al., 1998)."

Jan 1, 2012

By Abdelhak Bentriou

The choice of tool for the first well of an oilfield or gasfield is an important factor, given that we will be drilling with the same type of tool for the entire phase and explains why we need to have another type for comparison based on the efficiency of the tool and its ability to crush the rock, and the wear of different types of tools. Development of theoretical and practical tests to determine the optimal regime for drilling is required to take into account the characteristics of rock layers crossed. Classification of boring tools is based on the geometry of the teeth and depends on the hardness, the abrasiveness of rocks as well as their hydraulic system, but it is better to classify them according to the working conditions with a coefficient designating a discriminant. This is called physical characteristic of the drilling tool. The goal is to designate each element of the tool by a coefficient. Results were obtained from laboratory tests. Modeling the initial rate of progress by different types of tools allowed us to determine an adequate mathematical model of the speed initial progress in clean conditions. Using experimental data and statistics we have established the mathematical model of the average speed of progress as a function of time. With these equations we can determine the wear evaluation and analysis of these factors as an approach to classification according to their characteristics. The main equations for the selection of drilling tools will be based on the optimization of drilling parameters for each type of tool. After analysis, we choose the tool that gives a better forward speed with an optimal load and axial rotation.

Aug 1, 2013

By Frank Mucciardi, Zhongsen Yuan

A new heat transfer technology --- termed Thermopump technology has been developed. This technology originates from conventional heat pipe configurations but has now evolved into its own class of heat transfer units, which we refer to as `Thermopumps (TP)'. A key feature is that Thermopump technology can be applied to high temperature / high heat flux environments where conventional heat pipe technology fails. Moreover, when implemented in less demanding applications where heat pipes appear to operate, Thermopump units have been found to function more smoothly and reliably. This paper will introduce Thermopump technology and several applications of this technology in steelmaking and refining will also be discussed. In addition, this paper will focus on three classes of applications: 1) waterless, non-consumable, high efficiency Thermopump oxygen lance and/or burner for EAF's, 2) Thermopump ladle lance for the desulfurization process, and 3) Thermopump cooling panels for furnace walls and roofs. Facilities equipped with Thermopump technology are expected to he better than the current corresponding ones in terms of increasing productivity and energy efficiency while at the same time lowering operating costs.

Jan 1, 2004

By Henrik Saxén, Mikko Helle, Hamid Ghanbari

In this study, a process integration approach in a primary steelmaking is investigated to evaluate future operation concepts of a steelmaking site considering sustainability issues. Mathematical programming is used to study the integration of the steel plant with chemical units for utilization of available off-gases in the system, and carbon capturing and sequestration unit. Different industrial carbon utilization options are considered to find the best route of development. A multi-period optimization model is developed based on site-wide mass and energy balances by considering the availability of the fuels and by-product gases and their consumption in the production system and a conceptual polygeneration system. The objective is to reach maximum economic profit while environmental aspects of integrated system are considered for different fuel systems, alternative blast furnace reductants and implementation of new process technologies. The model can provide useful information concerning techno-environmental and economic aspects for decision-making and can estimate optimal operational condition of current and future primary steelmaking under alternative scenarios. The results of the work illustrate the potential to develop steelmaking towards more sustainable operation in the future.

Jan 1, 2015

By Q. G. Reynolds, R. T. Jones

The choice of furnace design parameters has a marked effect on the integrity of the furnace that is constructed. The design methodology for DC arc furnaces typically begins with the chemical reactions and feed materials that define the process. The specific energy requirement of the process, and the feedrates of the raw materials largely determine the power requirement for the furnace. A chosen value for the 'power intensity' sets the diameter of the furnace. Justification is provided for why this is a good choice of scale-up parameter. Equations are presented to quantify the resulting trade-off between thermal efficiency and the degree of error that can be tolerated in the balance between power and feedrate. This improved understanding should provide a better rationale for selecting an appropriate power intensity (or furnace diameter) for future furnaces.

Jan 1, 2015

By Tuomas van der Meer, Jukka Tanninen, Annukka E. Mäkinen, Mika Martikainen, Laura M. Nevatalo

The mining industry consumes huge water volumes and the waste streams typically contain sulfate, which has caused problems to many operations around the world. Discharge of sulfate to fresh waters is being restricted as the sulfate load increases salinity and causes problems when sulfate is reduced to toxic H2S by natural bacteria. To reduce fresh water consumption, internal water recycling had become a necessity in metallurgical processes. However, the recycling causes accumulation of sulfate and other components in water, causing problems to process performance and increases scaling in piping and equipment. Few technically feasible water treatment processes exist in the market that can be applied to decrease sulfate concentration below gypsum saturation level: biological sulfate reduction, membrane separation, ion exchange, evaporation and chemical precipitation. Some of these technologies are effective for treating wastewater, but there is typically a highly concentrated sulfate fraction left requiring still further treatment. Outotec has developed a sulfate removal solution, Outotec Ettringite process, which allows flexible control of residual sulfate concentration, thereby opening doors for increased water recycle within processes and control of the sulfate in discharged waters. In this article the results and benefits of this novel process along with examples of operating costs are presented.

Jan 1, 2014

Over the last three decades, the mining industry has been moving towards more underground mechanized mining methods and the number of LHD vehicles utilised has increased. The growth of mechanization and automation has benefited both workers and the mining companies. However, due to the design of the LHD vehicle and the limitations of the operating environment, restrictions to operator visibility are inevitable. The inability of the equipment operator to see clearly (i.e. people, objects or hazards) around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines, visibility assessments for existing machines are traditionally completed in the field using a light filament technique. Past researchers have used the light filament technique to collect obscuration zones around the equipment and to produce a 2D chart of this information. The 2D shadow diagrams have proved to be useful in highlighting potential equipment problems and have been performed repeatedly to show the potential of redesigning a part of the LHD for improving visibility. The light filament method involves manually collecting data and requires a level of judgment to be used. As a result the method is susceptible to errors and requires around three hours to complete. The objective of the current research is twofold; firstly to develop a rapid method for field visibility data collection using a laser scanner and secondly to compare results of repeat tests for both light filament and laser scanning methods. A MENSI GS100 laser scanner along with Pointscape and 3Dipsos software has been used to collect visibility information and process the data. The research aims to develop the laser scanner as a technique to rapidly evaluate the visibility profile of an LHD vehicle. Machine design changes can then be assessed quickly using these results.

May 1, 2004

By James R. Kuipers

Center for Science in Public Participation CSP2 ? Organized in 1997 to provide technical assistance to public interest groups on mining and water quality issues ? 80%of effort devoted to direct support of grassroots groups and tribal governments ? 20% of effort devoted to public-oriented education for public, tribal, state and federal regulators, and for industry ? Board represented by public interest groups, at large citizens, and academia ? Professional staff with experience from mining industry, academia and government ? website: www.csp2.org CSP2 Mission Statement The CENTER for SCIENCE in PUBLIC PARTICIPATION provides training and technical advice to grassroots groups on water pollution and natural resource development issues, especially those related to mining. CSP2 seeks to focus the debate on factual issues, as brought to light by its technical analyses, and whenever possible to seek consensus and win-win solutions. CSP2 also performs policy related work with federal and state regulatory agencies on the implementation of water quality, waste disposal, and mining reclamation regulations.

May 1, 2002