Search Documents

By R. P. Bhagat

The paper reports results on sinterability of iron ores from the mines of Tata Steel Limited. The objective was to improve tumbler index (TI) of sinter and its reduction parameters, reduction degradation index (RDI) and reducibility (RI) while maintaining strand productivity same or to improve. Pot sintering experiments were carried out with Joda and Noamundi mines having LOI 3.8% and 2.9% respectively. Sinter basicity (CaO/SiO2) was varied in the 2.1 to 2.5 range and its MgO content was kept in the 1.4% to 1.8% range according to the blast furnace requirement. The ignition condition and vacuum was maintained according to the plant practice. The effect of variables namely, granulometric composition of ores vis-à-vis that of sinter mix, bed height, solid fuel, moisture content of green mix on the sintering indices was studied. The productivity with Noamundi ore (26 %+6.3 mm) was lower than that with Joda ore (45% +6.3 mm) at 4% coke in the mix and sinter basicity (CaO/SiO2) 2.1. However, with 4% coke (ash 22%) the RDI value was significantly high in case of Noamundi Ore, which decreased significantly to 29% with 5% coke. The size parameter of ore fines and its LOI content do influence the sintering speed and the sinter properties significantly. At 2.1 basicity ratio, the sinter with the Joda ore having coarsergranulometry had highest TI (=70.2%). The RDI (27%) in this case was inferior to that (23.2%) when Joda ores with finer size was sintered. Better RDI with finer sized ore could be attributed to better assimilation of CaO/ MgO with more balanced and uniformly distributed hematite minerals. The size parameter has been inter-influenced by the coke requirement. With the lower mean sized Joda ore the sinter RDI decreased significantly to 23% and the productivity improved to 42.9 T/(sq m*d) when the coke in the mix increased from 4% to 5%. An attempt to reduce the coke in the mix from 5% to 4% with respect to both the ores was not successful as it resulted higher RDI and lower strand productivity. The present study has revealed that sinter RDI improves (decreases) with decrease in the sintering time, while such correlation was absent between TI of sinter and speed of sintering. Corollary to this observation, one can take advantage of other stronger parameters to increase the sintering speed (and hence sinter productivity) without affecting the sinter strength. In the present study higher FeO sinters has displayed excellent RDI, however cold strength of sinter was not correlated with its FeO content. The TI and RI parameters of sinter improves marginally with increase in its MgO content while RDI got worsened. Keywords: LOI content, iron ore, reduction properties, sinter, noamundi, joda

Sep 1, 2012

By E. R. Bobicki

"Low-grade ultramafic nickel ores, while representing a large potential nickel resource, are difficult to process due to their serpentine content. Microwave treatment is proposed as a technique to improve the beneficiation of ultramafic nickel ores by converting the constituent serpentine to olivine. The present paper reviews the microwave heating response of ultramafic nickel ores and resultant changes in mineralogy, as well as effects on grinding and slurry rheology. Beyond nickel extraction, microwave treatment improves the mineral carbon storage capacity of ultramafic ore tailings, providing a potential source of additional revenue via the sale of carbon credits. The combined positive effects, considered in the context of the whole operation, suggest an economically viable process is possible.INTRODUCTIONAs high-grade deposits become depleted, the processing of low-grade ores has become increasingly important. One such resource is low-grade ultramafic nickel ores. While representing a large source of nickel, these ores are difficult to process due to their serpentine content. Serpentine is a phyllosilicate mineral consisting of 1:1 stacked sheets of silica tetrahedra and magnesium hydroxide octahedra. There are three primary polymorphs: lizardite (platy), antigorite (corrugated) and chrysotile (coiled, fibrous). The anisotropic nature and non-spherical morphology of serpentine particles leads to complex rheology. Suspensions of serpentine minerals, especially those of chrysotile, exhibit high viscosity and yield stress, which can have a negative effect on comminution, flotation and dewatering operations. In flotation, serpentine is known to slime-coat pentlandite, a valuable nickel mineral, and form bubble-fibre aggregates that report to the froth, reducing nickel concentrate grade and recovery. Methods used to counteract the effects of serpentine in processing include desliming, the addition of chemical dispersants, salts or acid, and dilution (Bobicki et al., 2014a). Microwave pre-treatment has been proposed as an alternative way to eliminate the deleterious effects of serpentine in ultramafic nickel ore processing by converting the serpentine to olivine via dehydroxylation, which occurs at 600-700oC (Reaction 1). Olivine is isotropic, consisting of isolated silica tetrahedra linked by octahedrally coordinated magnesium ions, and has the same surface potential as pentlandite at the pH of flotation (~pH 9). Furthermore, since olivine is more reactive to CO2 than serpentine, microwave pre-treatment creates an opportunity to store more CO2 in tailings, an attractive option for mining operations looking to increase their bottom line where carbon pricing exists."

Jan 1, 2018

By Wenqing Qin, Yunfan Wang, Ximei Luo, Fen Jiao

In order to investigate the effect of nanobubbles on adsorption of surfactant on mineral surface, the nanobubbles on the surface of calcite with -37µm fraction in the sodium oleate system were controlled by pressurization and decompression to mixing vessel. Subsequently, the adsorption amount of sodium oleate on the surface of calcite were detected by ultraviolet spectrum at different stirring times and different pressures. At the same time, the nanobubbles on the calcite surface were imaged with atomic force microscopy (AFM). In addition, a homemade vacuum Hallimond tube device was used for the flotation of single mineral, and the grade and recovery of minerals in concentrate was used to determine the influence of the nanobubbles on flotation. The experimental results showed that a large number of nanobubbles were found on the calcite surface by AFM under the dissolved oxygen difference (DOD) condition of -4 mg/L. And a large difference in adsorption capacity of sodium oleate on the surface of calcite was observed under different air pressure conditions. It indicated that the ambient pressure had a certain effect on the adsorption of sodium oleate on the calcite surface, and this effect did not depend on the constant low pressure or constant normal pressure, but depended on the changing process of pressure. The single mineral flotation experiment results indicated the recovery of calcite under decompression condition (formation condition of nanobubbles) was 1.5-2 times that under constant normal pressure, and the flotation time is much shorter. Moreover, the recovery under constant normal pressure was greatly influenced by flotation time. In this paper, only one aspect of the effect of nanobubbles on mineral flotation was preliminarily explored. It was confirmed that after vacuum-pumping, the adsorption of sodium oleate on calcite surface could be increased, the flotation time also was greatly reduced and the recovery of calcite was increased.

Jan 1, 2018

By I. Gombköto

In the EU-region, the automatically operated approximately 200 (rotating hammer) shredder plants processing large technical equipment (end-of-life vehicles, large household appliances) annually produces 8-9 million tons of non-metallic grinded by-product, which ends in landfills, without recovery. Although this by-product is organic material, still contains large amount of metal components worth recycling. These operations, such as shredding and processing end of life vehicles or mixed metal components are a growing market and it is become more potential if EU directive 2002/96/EC will become obligatory for new member and candidate countries and they have to apply EU regulations. Eddy current separators (ECS) are one of the most important units of separation of non-ferrous metals from insulators in waste recycling. The product of ECS processing of shredded ELV?s is usually a mixture of Al, Cu, Brass and stainless steel. This mixture has relatively low price on the market, while purified metal products are required by smelters for which shredder operators are able to get even higher price. Our aim at University of Miskolc was to find solution producing pure metal products using dry separation processes. Authors are presenting a possible solution, using ECS. Institute of Raw Material Preparation and Environmental Processing possesses an ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor. The subject of our work was to investigate the behaviour of model particles with different shape, conductivity (aluminium and brass), orientation and size in order to separate Al and Brass. We used model particles with similar shapes of shredder plant originated ones. The magnetic flux and magnetic frequency was constant and derived by the design of the rotor. During our research work, belt speed and rotor speed of ECS were varied. The particle distance and trajectory caused by throwing was determined and the results are reported in this paper.

Sep 1, 2012

By Avinash Tripathi

It is now well known that the size distribution of the particulate solid has a significant effect on the breakage behavior of particles in the wet as well as dry modes of ball milling operation. In the context of the size discretized batch grinding kinetic model, grinding behavior of particles is characterized by the breakage rate parameters, k, and breakage distribution parameters, B. Understanding the nature of variation of these two sets of parameters with particle size distribution is important for simulation and control of operation of production mills. However, so far it has not been possible to track the variation of both the set of parameters with grinding time simultaneously. In this paper an attempt has been made in this direction by using a modified functional form approach with time dependent constants. Keywords: dry and wet ball milling, breakage rate and distribution parameters, effect of particle size distribution

Sep 1, 2012

By Andrzej Luszczkiewicz, Aleksandra Potulska

"Flotation is a basic process of beneficiation of mineral raw materials which requires very fine grinding for liberation of valuable minerals. Probably flotation will also play this role in the future. In the case of flotation of difficult-to-upgrade non-ferrous ores, currently one of the most important trends in technology development is solution to fine grinding even down to a few micrometers in size and elaboration of effective flotation technology for such fine particles. Both industrial flotation data and many investigators suggest that the best results of flotation of ore minerals are observed for particle size range from 20 to 100 µm. Many base metal ores require grinding below 20, or even 10 µm, to liberate valuable ore components. However, industrial flotation of particles below 20 µm in size creates numerous challenges. Further complications may be caused by a complex nature of the ore, especially when the valuable metals are present in several different sulfide minerals. This problem occurs in the case of the Polish sedimentary copper ores. In the present study, flotation of the ore of different size distributions and degrees of grinding, having the size of particles below 25 µm, was investigated. The behavior of different sulfide minerals naturally present in the ore was analyzed. The best results of flotation tests were obtained for the ore ground down to 95% below 25 µm. Narrow size fractions -10; 10-15; 15-25; 25-40, and +40 µm were separated using special micro-sieves and mineralogical as well as chemical analyses of each size fraction were carried out for monitoring the behavior of the fine sulfide particles. Differences between flotation of chalcocite-digenite, bornite, chalcopyrite, covellite, galena and pyrite-marcasite naturally occurring in the ore were described. The role of different particle sizes in flotation performance of each mineral was also presented."

Jan 1, 2014

By Haragobinda Srichandan

The present study aimed to investigate the bioleaching efficiency of moderate thermophilic microorganism in a growth medium without Fe supplement on three different size fractions of spent catalyst obtained from petroleum refinery. All the experiments were conducted on shake flasks at a temperature of 65 °C and a pulp density of 10% (w/v) on three size fractions viz. 45-106 µm, 106-212 µm and >212 µm and a working volume of 100 ml comprising of 10 ml of microbial inoculums and 90 ml of Modified Kelly medium. The parameters like pH, redox potential, viable planktonic cell count and the amount of acid addition was measured and quantified on regular basis to follow the progress of the bioleaching. The pH varied much in the lag and logarithmic phase of the experiments but stabilized toward the stationary phase. The total acid additions in each batch experiment were determined the amount of Conc. H2SO4 requirement, which ranged between 683-757 kg/ton of spent catalyst. The redox potential values ranged between 625-650 mV, Ag/AgCl, but were very low ranging between 350-450 mV during initial period. The planktonic viable cell count ranged between 108-109 cells/ml active in the bioleaching system, without any toxic influence of the spent catalyst, but initially due to fall in redox potential and new environment for the microbes, their population was low. The leaching yield of Ni was found to be promising with very high leaching yield of 92-96% followed by Al as 61-62%, which means both Ni and Al leaching were favored by the moderate thermophilic bioleaching compared to the mesophilic bioleaching. There was very little difference in the leaching yield, when compared with different size fractions and hence grinding can be avoided prior to leaching. This process seems to be economical as no Fe source is supplemented together with no requirement of grinding and over all a biological process resulting for an eco-friendly process for future optimization of the metal recovery from petroleum refinery spent catalysts. Keywords: bioleaching, spent catalyst, thermophile, 9K medium

Sep 1, 2012

By Aysan Molaei, Kristian Waters

Solvent extraction is the one of the most common techniques for recovering metal ions from aqueous systems. However, solvent extraction is generally limited to relatively high concentrations and requires a high organic/aqueous ratio. Predispersed solvent extraction (PDSE) is a modified solvent extraction technique in which organic phase pre-comminute into colloidal liquid aphrons (CLAs). In this study, the extraction of copper by the PDSE technique was investigated. The main focus of this study was on the characterization and application of CLAs under different operational conditions, and to investigate the effects of different parameters on the extraction of copper from dilute streams. The effect of phase volume ratio (PVR), initial extractant concentration and initial copper concentration was studied and optimum conditions for copper removal using CLAs generated by LIX 984N as extractant, oil soluble and water soluble surfactants were proposed. Experimental observations indicated that PVR and initial LIX 984N concentrations had a significant effect on copper extraction.

Jan 1, 2014

By S. A. Kondratyev

"The present research work aims at disclosing the dependence of flotation concentrate recovery and its grade on the physically adsorbed collecting reagent properties, viz., surface pressure in the reagent film at gas-liquid interface, velocity of reagent species spreading over the said interface, relation between interaction energies of collector molecules within a film and with water dipoles.When using a single collecting reagent it is possible to improve the flotation concentrate grade in two ways, namely, by reducing collector consumption rate or using a weaker reagent. According to the proposed mechanism, a decrease in the physically sorbed species of the collector leads to a decrease in the rate of removal of the kinetic restriction of a flotation contact formation. As a result, the recovery of the useful component is reduced and the content of valuable components in the flotation concentrate is increased. The relationship between the spreading velocity of physically sorbed species at the gas-liquid interface and the recovery and quality of the flotation concentrate has been experimentally proved. Reduction in collector consumption lowered the valuable component recovery at a higher grade of the concentrate.The reasons were established for a rise of valuable content in the flotation concentrate if a weaker collector was used. It is justified that the use of a weaker collecting reagent with a shorter hydrocarbon fragment declines physically sorbed species of collector. The spreading velocity of collector derivatives at gas-liquid interface tends to lower along with less participation physically sorbed species of collector in formation of a flotation aggregate. The spreading velocity is determined for products of interaction between butyl-and ethyl-xanthates and lead nitrate at gas-liquid interface. It is found that the spreading velocity of butyl-xanthate derivatives is higher than that of ethylxanthate derivatives.The research work gets insight into the nature of relation between useful component content in the flotation concentrate and the useful component recovery. It is pointed out that adjusting the collecting activity of a collector makes it possible to influence a useful component content in the froth product thus gaining a compromise between wanted grade and recovery parameters."

Jan 1, 2018

By L. J. Li, Q. Zhang, Z. H. Liu, Q. L. Chen

Phosphogypsum (PG) is an industrial waste from the production of phosphate fertilizer. The utilization of PG is restricted by its containing impurities, and the pretreatment is crucial to eliminating these impurities. The purpose of the research is to recycle pretreatment PG as raw material for preparation of a-calcium sulfate hemihydrate (a-HH) by salt solution method. The effect of pretreatment technologies of lime neutralization and washing on dehydration rate, phase composition and morphology evolution of a-HH were investigated by crystal water content analysis, XRD and SEM. Furthermore, the change of pH in the reaction process was also discussed in detail. The results show that the dehydration rate of conversion PG to a-HH increases and the corresponding induction period, crystal growth period and total time decrease with an increase in CaO dosage from 0.2% to 0.6%. In the presence of 0.4% CaO or 0.6% CaO, the a-HH presents a long hexagon-prism-shaped crystal with a purity of 94%, and the end face of a-HH presents polyhedron. The system pH sharply decreases with the reaction time under different CaO dosage, and the pH variation from the initial alkalinity to acidity. The main reason is that as the co-crystallized phosphorus dissolved and released HPO42-, and with the pH decreasing to 4-5, HPO42- transformed into H2PO4-. The dehydration rate of washing PG is lower than that of original PG. Compared with the original PG, a-HH with the larger width and smaller aspect ratio can be achieved from the pretreatment PG subjected to lime neutralization and washing, meanwhile the crystal surface is more smooth.

Jan 1, 2018

By Xiaolu Ye

"Comprehensive utilization of Bi and Sn from the tin-associated polymetallic tailings by “gravity separation – flotation combination process” has been studied, which was verified that the novel process is an effective method to deal with the high content pyrrhotite tin-associated polymetallic tailings. In this investigation, ore property analysis and magnetism analysis of pyrrhotite were conducted to research and develop reasonable beneficiation flowsheet. The results of ore property analysis present that pyrrhotite was not closely related to bismuth and tin minerals. Particle size analysis results indicated that pyrrhotite was mainly in the form of fine particles. The magnetic analysis results show that pyrrhotite was distribution in all the three types of pyrrhotite in a single mining area, which indicated that variable magnetism of with different crystal structure pyrrhotite. The process of “low intensity magnetic separation - high intensity magnetic separation” shown an excellent adaption for the high content pyrrhotite tin-associated polymetallic ore compared with the single flotation process based on the magnetism variable of pyrrhotite. The results of whole process test indicated that a bismuth coarse concentrate assaying 5.63% of Bi at 81.77% recovery was obtained, which treat the conditions for the Bi-S separation flotation. In addition, the content of sulfur in the tin concentrate decreased from 2.5% to 1.5%, which provided a new reference for other tin-associated polymetallic tailings. INTRODUCTION Tin has been applied extensively in catalytic chemistry, gas sensors, tin plating, and plumbing. Tin-bearing polymetallic ores have been the important deposit types to recycle tin with the rapid depletion of mineral resources. The comprehensive utilization of the associated elements has been a preoccupation for the mineral processing researchers."

Jan 1, 2018

By Xumeng Chen, Yongjun Peng, Dee Bradshaw

Regrinding rougher flotation concentrates has become a common practice when processing low grade and complex ores. It not only reduces the particle size and improves mineral liberation but also modifies particle surfaces and pulp chemistry due to the strong electrochemical reactions taking place during regrinding. Therefore, the floatability of minerals in the subsequent cleaner flotation is influenced by the regrinding conditions. This paper presents the effect of regrinding conditions on the mineral floatability from both industrial studies in the plant and fundamental studies in the laboratory. Different regrinding conditions were considered, including grinding media, the electrochemical properties of minerals, pulp chemistry (pH, Eh, DO), and breakage mechanisms in tumbling and stirred mills. Results indicate that the selection of regrinding conditions and mill types should not only depend on grinding energy efficiency and liberation but also depend on the surface properties and pulp chemistry produced for effective mineral flotation and separation at the cleaner stage.

Jan 1, 2014

In this study, the effect of different regrinding conditions on the depression of fine pyrite at the cleaner stage was investigated. The regrinding condition was manipulated by different grinding media (stainless steel and mild steel). It was found that, after regrinding with mild steel grinding media, the flotation recovery of pyrite is much lower than with stainless steel grinding media, and it is more difficult to restore by adding more collector. This means, regrinding with mild steel grinding media may depress the pyrite flotation more strongly. The copper activation of pyrite during regrinding was also studied. It was found, that the mild steel grinding media is more beneficial to copper activation than stainless steel media. Additionally, the analysis of pyrite recovery based on the particle size indicated, that the fine particles are more susceptible to different grinding environments than intermediate and coarse particles and therefore are more easily depressed with a much lower flotation recovery.

Sep 1, 2012

By P. Fawell, C. Castillo, C. Ihle

"The need to reduce fresh water consumption has pushed many Chilean mining companies to utilize seawater obtained from distant locations. At the same time, increasing amounts of fine particles in copper tailings raise new operational challenges, in particular, the thickening and transport of tailings featuring significant fine fractions, which are predominantly clays. In the present paper, we study the role of salinity – using seawater and NaCl – on the flocculation efficiency of copper sulphide tailings to which kaolinite was added. To mimic the water recovery stage in thickeners, flocculation has been induced in jar tests and the corresponding aggregate size distribution has been estimated from chord length distribution data obtained using a focused beam reflectance measurement (FBRM) probe, at various mean turbulence intensities. Results show that for constant flocculant dosing, a measurable influence of the salt on the resulting aggregation exists. For each case, resulting optimal turbulence levels are also reported, a particularly interesting feature when comparing flocculation efficiency of the coarse and fine fraction. INTRODUCTION The concentration of copper minerals through comminution and flotation is intensive in the use of fresh water. The need to reduce the consumption of fresh water and the environmental standards associated with increasingly demanding mining operations have driven improvements in the techniques of recovering water from tailings. The challenges are even greater when required to treat minerals with high clay contents. In Chile, kaolinite is one of the most important clays to consider due to its abundance in the tailings from many operations. The most common and highest throughput unit operation in the mining industry for the recovery of water from tailings is gravity thickening, with sedimentation of fine particles assisted by flocculation. Flocculation is the process of forming aggregates by contacting the suspended particles with a flocculant. The flocculant is typically a water-soluble synthetic long-chain polymer, where copolymers of acrylamide and sodium acrylate are the most common types used in the Chilean mining industry. The aggregation mechanism includes the following key steps: (1) flocculant distribution through the suspended particles, (2) flocculant adsorption onto particle surfaces, and (3) collisions between particles leading to polymer bridging to form aggregates, but concurrently (4) breakage of aggregates becomes a factor under prolonged shear (Gregory, 1988)."

Jan 1, 2018

By B. Q. By

TiO2 is an ideal material for catalytic technology due to its unique properties. In this paper, Sm3+ doped TiO2 photo-catalyst was developed to improve the efficiency of TiO2 and to use the natural light as irradiation source, which was made from Titanium Tetrabutoxide and Samarium Oxide with the Sol-Gel process. The Sm3+-TiO2 photocatalyst was used to degrade reactive orange 4 (RO4) in Azo Dyes. The effects of solution pH, Sm3+ concentration and catalytic time on the degradation rate of RO4 were studied. The characteristics of the catalyst were analyzed with XRD and TEM. The experimental results show that the catalyst has high activity in the degradation of RO4. The Azo bonds of RO4 are active and easily broken by oxidation. The catalytic activity of the Sm3+ doped catalyst greatly depends on the pH of solution. The catalyst has high photo-catalytic activity at both neutral and alkaline conditions. The degradation mechanism of the Sm3+ doped TiO2 photo-catalyst was also discussed.

Jan 1, 2014

By Liu Xinghua

Yuanjiacun iron ore located in Shanxi province of China has finely disseminated grain size and contains refractory iron-bearing silicate gangue minerals such as chlorite. Therefore, a large amount of secondary slime (the content of -10µm fraction was up to 32.92%) was produced inevitably in fine grinding process, and chlorite was also enriched in concentrate from the content of 4.3% to 14.8% after high intensity magnetic separation. These two characteristics result in the difficulty to deal with Yuanjiacun iron ore by flotation. In this test work, contrast tests between single reverse flotation and selective flocculation desliming-reverse flotation were conducted on Yuanjiacun iron ore. The test results show that after selective flocculation desliming, the iron grade of cationic reverse flotation concentrate increases by 6.15% and the recovery increases by 7.25%; the iron grade of anionic reverse flotation concentrate also increases by 2.15%. Furthermore, analyses of grain size composition and mineral composition were carried out on separation products, the results indicate that selective flocculation desliming plays a dual role of optimizing grain size composition of flotation feed and removing iron-bearing silicate gangue minerals (chlorite) effectively.

Sep 1, 2012

In the present work, the flotation behaviours of zircon, rutile and ilmenite using sodium oleate as collector in absence and presence of depressants were thoroughly investigated. The maximum in the flotation recovery of any of the above minerals falls within similar pH ranges. A range of inorganic and polymer depressants were examined in order to improve the separation of zircon from rutile and ilmenite. Optimum values of conditioning pH and depressant concentration to achieve maximum recovery and best selective floatability of zircon were obtained. Selective flotation of zircon from Ti-bearing minerals was anticipated from single mineral experiments under different pH values, depressant and collector conditions.

Jan 1, 2014

By Zehong Wang

Selecting sodium polyacrylate (PAAS) as grinding aid, the effect of grinding aid on the grinding efficiency of bauxite taken from Shanxi province was studied and its mechanisms were analyzed by measuring the variation of adsorption characteristic, pulp viscosity, surface electric potential of the bauxite and the surface appearance of particles. The results showed that, compared with no grinding aids added the content of -0.074mm in the ground product was increased by 5.45 percentage points under the optimal grinding conditions adding PAAS as grinding aid when the amount of PAAS was 0.7%wt of bauxite. Because the physical adsorption and chemical adsorption were occurred on the bauxite surface, which could reduce the pulp viscosity, change the surface electric potential of the bauxite, enhance the surface appearance of particles and lower the surface hardness of the bauxite, the grinding efficiency of bauxite was increased by PAAS. Keywords: bauxite, grinding aids, grinding efficiency, mechanism

Sep 1, 2012

By Li Maolin, Cui Rui, Wang Guanghui

"As the stirrer speed directly affects the motion of grinding media, and hence the interactions with material particles to be ground, the rotation speed of a stirred mill is well recognized as one of the most important factors affecting the grinding performance. In this work, the effect of stirrer speed on grinding performance in terms of grinding rate and grinding energy efficiency was quantitatively investigated. Batch wet grinding tests of quartz powder at different stirrer speeds were performed, using a self-made horizontal stirred mill with alumina balls as grinding media. Grinding time, operating power and the sizes of ground product were recorded to analyse the grinding performance. The test results showed that grinding processes followed the first order grinding kinetics. The grinding rate constant increased with the increasing stirrer speed. Based on the grinding kinetics, the grinding energy equation was established. The energy utilization coefficient in the energy equation can be used as an indicator of energy efficiency. The energy efficiency decreased with the increasing stirrer speed. Quantitatively, with the stirrer tip speed increasing from 4.25m/s to 9.35m/s, the grinding rate constant was improved by 441.47%, whereas the energy utilization coefficient was decreased by 39.35%. The grinding rate constant and energy utilization coefficient can be used to evaluate the grinding performance when the grinding conditions need to be adjusted. The adjustment of grinding conditons would be optimal when grinding rate get significant improved with little decrease of energy efficiency."

Jan 1, 2014

By Ritva Tuunila, Antti Häkkinen

"Wet stirred milling is one of the most effective grinding methods in producing very fine powders in large scale production, but it is a very energy-intensive process, especially when pigments or even nanosize particles are produced. Therefore, optimization of the process parameters is important. The specific energy consumption is a function of stress energy, which describes the effect of tip speed and media characteristics on grinding, and is related to the number of stress events during milling. In effective grinding, a large number of stress events are necessary. The stirrer configuration influences the number of stress events and their intensity, because the motion of the media and the suspension are caused by a rotating stirrer. The effect of three different stirrer types: a pin, disc and blade stirrer, on the grinding rate, i.e. product fineness and specific energy were investigated in this study with a batch laboratory stirred mill with two tip speeds. The material used in the experiments was calcium carbonate. The results obtained with the smaller tip speed showed approximately similar grinding rates and energy consumption for all stirrer types. When looking in closer detail, the blade stirrer seemed to give the finest product with all grinding times compared to the pin and disc stirrers, which both produced almost the same product fineness with the same grinding times. The specific energy consumption was the smallest with the disc stirrer, but not very big differences were obtained. With a higher tip speed, greater differences occurred both in grinding rates and specific energy consumption. The blade stirrer was the most effective in grinding, and the pin stirrer the next. The net energy consumption for the blade and pin stirrers was almost the same, but it was slightly higher for the disc stirrer."

Jan 1, 2014