Search Documents

By S. Z. Khan, Veerendra Singh, Y. Rama Murthy, S. Prasad, Sunil Kumar Tripathy, Gajanan Kapure

"In this study, a low-grade ferruginous low-grade chromite ore was subjected to reduction roasting by using conventional heating as well as microwave heating. Sukinda chromite ore deposit contains majorly iron-bearing minerals as gangue phase. The magnetic susceptibility of these minerals enhances effectively after reduction roasting. Alteration of crystalline structure and magnetic property of these metals enables separation of low-grade ore by using magnetic separation. Conventional roasting studies by varying the temperature, time of reduction and reductant dosage were changed for low-grade ferruginous chromite ore. Similarly, microwave power, retention/exposure time and reductant dosage varied for reduction roasting studies under microwave environment. It is found that low-grade ferruginous chromite ore can be upgraded by reduction roasting and 61.2% Cr2O3 was recovered with a chromium-to-iron ratio of 1.93 from feed chromium-to-iron ratio of 1. Microwave reduction roasting studies resulted in upgradation of chromium-to-iron ratio to 1.73 with a recovery of 21% Cr2O3.INTRODUCTION The chromite ore occurs as a spinel containing oxides of chromium, iron, magnesium and aluminium. Most of the Indian chromite deposits are of ferruginous (rich in iron content) which indicates the abundance of ferruginous gangue minerals along with chromite. The primary use of chromite ore is towards the production of ferrochrome alloys. Chromite ores with less than 40% Cr2O3 and the chromium-to-iron ratio (Cr-to-Fe ratio) <1.8 is considered to be unsuitable for the smelting process (Tripathy et al. 2012, Tripathy et al. 2012a). A considerable amount of low-grade chromite ore and overburden excavated during chromite mining is getting accumulated every year, causing a threat to the environment. Its disposal poses a significant challenge and, hence, the beneficiation of low-grade chromite ore and its utilisation has been attracting a lot of attention. Different physical method of beneficiation methods is generally employed for the improvement of the Cr-to-Fe ratio (Tripathy et al. 2012, Murthy et al. 2011, Tripathy et al. 2012a, Tripathy et al. 2013, Tripathy et al. 2016, Tripathy et al. 2017, Tripathy et al. 2017a). It is observed that the enrichment of the chromite ore is carried out by using gravity and in some places by magnetic separation. However, the enrichment of Cr-to-Fe ratio from low-grade ferruginous chromite ore is difficult by using the above-mentioned beneficiation methods due to the presence of near gravity and near-magnetic susceptibility minerals along with chromite. However, an alternative beneficiation method is needed to explore for the beneficiation of such mineral deposits. Reduction roasting followed by magnetic separation is an alternative option for the separation of these types of ores which is widely reported for the iron and manganese ore (Li, et al., 2010; Chun, et al., 2014, Rath et al., 2018). These processes are majorly focussed on differentiating the magnetic susceptibility between minerals and subsequent separation by using magnetic field. The main advantage of such method is dry process option along with the pre-processed product for the costly smelting process. Also, the roasting of minerals in a microwave environment is also an active research topic in the recent time. So, the amenability of the separation feature of the roasting process by using conventional heating as well as microwave heating can be can be studied for the low grade ferruginous chromite ores."

Jan 1, 2018

By X. O. Xia

This paper introduces a kind of flotation machine for nonferrous metal, ferrous metal and non-metal minerals. With the application and development of flotation machine, researching the designment of master parts, including tank, impeller, stator, false bottom. Through the commercial run to validate the correctness of designment, achieving satisfied technical and economic target and supplying a kind of efficient and reliable flotation machine.

Jan 1, 2014

By M. R. Robben

Carbonates have gained significant economic importance for the human kind. On one hand over a hundred uses are listed for carbonates. On the other hand, carbonates host base metal deposits. Although the carbonates play a significant part in the development of those deposits, in the mineral processing they consume acid and cause selectivity problems during flotation and leaching. Carbonates also accompany other industrial minerals as waste rock. For all those cases it necessary to find a technique to separate carbonate as early as possible in the processing chain. In this paper, the applicability of near-infrared spectroscopy (NIRS) sorting for the separation of carbonates is discussed. NIRS sorting is a sensor-based sorting technique, in which particles are singularly detected by a sensor and then rejected by an amplified mechanical, hydraulic or pneumatic process. This technique can for example be implemented in the process as a pre-concentration step for coarse particle sizes up to 300 mm. NIRS sorting discriminates among materials based on the difference that exist between their spectral properties in the near-infrared (NIR). Vibrations of molecular bonds in carbonates cause characteristic spectral properties in the NIR, which makes carbonates detectable, possible to identify, distinguish and separate from other rock materials. The spectral properties can also be used to distinguish between different carbonate minerals and mixtures. If the spectral variations are large enough for detection, sorting based on NIRS is possible. Feasibility studies on sensor-based separation of carbonates in the processing of talc, borate, fluorite, marble, zinc-oxides, copper sulphide and iron ore as well as the discrimination of calcite and dolomite mixtures are conducted and indicate the high potential of NIRS sorting in the minerals industry. Keywords: carbonate separation, sensor-based sorting, near infrared spectroscopy, NIRS sorting

Sep 1, 2012

By R. S. C. Smart

Surface chemical factors, including the balance of hydrophobic (e.g. collectors) and hydrophilic (e.g. oxidation products, precipitates) species, are major control determinants in flotation rates of specific minerals and therefore grade and recovery. There are a number of challenges involved with the surface analysis of different mineral phases from process streams in a flotation facility. The first is to collect samples that are representative of the process and retain their surface chemistry prior to introduction into the instrument. The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles, confident mineral selection can be difficult with many multi-metal minerals and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers. The third challenge is to provide a statistical surface analysis of multiple grains of the same mineral. Methods to achieve these aims are described. Principal component analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. Specific examples from both lab and plant operations, demonstrate that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation. A study of copper ion transfer (inadvertent activation) from chalcopyrite to pyrite and sphalerite clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases corresponding to their flotation response. The PCA analysis applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between chalcocite and heazlewoodite minerals. The statistical analysis has been able to identify mechanisms controlling recovery and selectivity. High intensity conditioning (HIC) tests in which sphalerite was separated from a complex sulfide ore gave a 5% increase in the overall Zn recovery. The PCA/ToF-SIMS statistical analysis revealed the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. HIC conditioning resulted in the removal of these gangue fines improving surface collector attachment efficiency.

Jan 1, 2014

By Victor Avdokhin, Ivan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation.Catching coat is formed of natural magnetic and weak-magnetic placer minerals in field of magnetic system of the sluice. Magnetic minerals, placing along magnetic lines of force, form rough coat of fluffy structure. Size of the magnetic particles is chosen taking into account expected size of gold particles, which are to be fixed on the rough coat or between the magnetic particles. Changing coarseness of particles of mineral bed allows to regulate selectivity of recovering heavy minerals.Forming artificial fleece from magnetic minerals of initial sand, increasing capacity of the bed and relative hydraulic proportionality of mineral particles of the bed provide for the most effective recovery of fine gold."

Jan 1, 2003

By M. Saghaeian, R. Hejazi, M. Farahani, M. Dehghani, A. Tohry

"Wet tailing dams of iron ore processing plants typically contain a significant amount of valuable minerals. In more recent years, due to the increase in iron’s prices and technological innovations, as well as the low energy consumption which required for processing of materials from tailings, dams can consider as potential valuable deposits. However, the production of iron concentrate from tailings is usually complicated where the high moisture content of the material, the high clay content and the presence of chemicals of processing such as flocculants, acids and flotation reagents, all make materials highly sticky which can be easily swollen. In the present paper, the optimization of operational parameters to recover ultrafine hematite iron ore from the wet tailings dams of the Chador-malu iron ore mine was investigated. The optimization of operational parameters, showed that with modification of the washing unit components for slurry making, the challenge of constraints from feeding the plant could be overcome. To decrease the magnetite content in the tail stream of the medium intensity magnetic separation (MIMS) and subsequently increase the efficiency, the orifice of the cleaner tail flow exit pipe was changed from 7 inches to 3 inch and yoke angle changed from 14 to 8 degrees. These changes increased mass yield by 3% and decreased the magnetite content in the final tailings to 1.2%. By recirculating the cleaner SLons of final tailings within the circuit, the solid percentage of the feed to rougher SLons decreased to around 15%, and as a result the matrices were not overloaded that easily, and mass yield increased to about 13% from 7%. All the above mentioned optimizations were achieved without significantly affecting the concentrate Fe grade."

Jan 1, 2018

By P. K. N. Raghavan

Bauxite is the principal source for the production of aluminum metal which has gained tremendous importance over the years due to its versatility as a metal capable of substituting almost all of the non-ferrous metals, non metals like wood, plastics, fibre glass, etc. and even steel in many applications. 90% of the high purity alumina needed for the production of this wonder metal in the world comes from bauxite. Even though alternate methods have been developed to produce alumina from non bauxite sources, owing to the high capital and operating costs involved, Bayer process still retains the superiority among all the methods by virtue of its simplicity and favourable economics. Bauxite continues to be the perfect ore for alumina production and its remarkable utilization makes it the most important non-ferrous ore. Most of the Alumina Refineries in the world process different types of bauxite and that too from varied sources. The technology employed in the Alumina Refineries depends on the Bauxite processed, with an ultimate view to produce alumina of required quality in the most efficient manner. Bureau of Indian Standards (BIS) and Indian Bureau of Mines (IBM) had from time to time put forward bauxite specifications for metallurgical and other applications. However, these are found no fully based on alumina technology, present developments and availability of different types of bauxite in the country. The aim of this paper is to provide scheme of metallurgical grading of Indian Bauxite based on the background of alumina processing technologies and availability of various types of bauxite in the country. Efforts are made here to evaluate beneficiation techniques for central Indian Bauxite from the point of view of alumina production. Keywords: bauxite beneficiation, digestion, alumina, gibbsite, bohemite, diaspore

Sep 1, 2012

By E. R. Bobicki

"Low-grade ultramafic nickel ores, while representing a large potential nickel resource, are difficult to process due to their serpentine content. Microwave treatment is proposed as a technique to improve the beneficiation of ultramafic nickel ores by converting the constituent serpentine to olivine. The present paper reviews the microwave heating response of ultramafic nickel ores and resultant changes in mineralogy, as well as effects on grinding and slurry rheology. Beyond nickel extraction, microwave treatment improves the mineral carbon storage capacity of ultramafic ore tailings, providing a potential source of additional revenue via the sale of carbon credits. The combined positive effects, considered in the context of the whole operation, suggest an economically viable process is possible.INTRODUCTIONAs high-grade deposits become depleted, the processing of low-grade ores has become increasingly important. One such resource is low-grade ultramafic nickel ores. While representing a large source of nickel, these ores are difficult to process due to their serpentine content. Serpentine is a phyllosilicate mineral consisting of 1:1 stacked sheets of silica tetrahedra and magnesium hydroxide octahedra. There are three primary polymorphs: lizardite (platy), antigorite (corrugated) and chrysotile (coiled, fibrous). The anisotropic nature and non-spherical morphology of serpentine particles leads to complex rheology. Suspensions of serpentine minerals, especially those of chrysotile, exhibit high viscosity and yield stress, which can have a negative effect on comminution, flotation and dewatering operations. In flotation, serpentine is known to slime-coat pentlandite, a valuable nickel mineral, and form bubble-fibre aggregates that report to the froth, reducing nickel concentrate grade and recovery. Methods used to counteract the effects of serpentine in processing include desliming, the addition of chemical dispersants, salts or acid, and dilution (Bobicki et al., 2014a). Microwave pre-treatment has been proposed as an alternative way to eliminate the deleterious effects of serpentine in ultramafic nickel ore processing by converting the serpentine to olivine via dehydroxylation, which occurs at 600-700oC (Reaction 1). Olivine is isotropic, consisting of isolated silica tetrahedra linked by octahedrally coordinated magnesium ions, and has the same surface potential as pentlandite at the pH of flotation (~pH 9). Furthermore, since olivine is more reactive to CO2 than serpentine, microwave pre-treatment creates an opportunity to store more CO2 in tailings, an attractive option for mining operations looking to increase their bottom line where carbon pricing exists."

Jan 1, 2018

By Venkataramana Runkana, Aditya Pareek, Vishnu Masampally, Nagaravi Kumar Varma Nadimpalli

"Recovery and grade of the ore produced are two important metrics, which define the profitability of a mineral processing plant. Achieving high grade and high recovery at the same time in a mineral processing plant is difficult due to conflicting nature of the two objectives. To explore the operability limits of the plant operations and find the set of operating conditions that can help achieve the best possible recovery and grade, there is a need to solve a multi-objective optimization (MOO) problem. Past research focused on building a plant-wide simulation model or on optimization of individual units or a part of a mineral processing plant like grinding circuit, crushing circuit, etc. However, it is necessary to consider optimization of the complete plant in order to optimize the plant performance. Here, we have formulated the mineral processing plant performance optimization as a MOO problem. We have applied machine-learning algorithms such as random forest to build models to predict the recovery and grade of the ore. A non-dominated sorting-based multi-objective evolutionary algorithm called NSGA-II (Non-dominated Sorting Genetic Algorithm II) was employed to solve the MOO problem. Since the number of parameters that influence recovery and grade are quite large, we have applied machine-learning algorithms for feature selection or identification of key process variables. Pareto optimal conditions were determined for manipulated variables like grinding mill throughput, speed ratio at SAG mill, speed of centrifugal pump, water addition at different locations etc. The results obtained are useful in identifying the operability of a mineral processing plant to achieve the optimum grade and recovery for a given feed grade and the processing circuit. INTRODUCTION Copper is majorly mined or extracted as copper sulfides from large open pit mines in porphyry copper deposits. Among all the available ores, sulfides are the most commercial ores, especially chalcopyrite (Greenwood and Alan, 1997). Copper grade in these ores generally lies between 0.4 to 1.0%. In order to perform smelting operation, the grade of copper has to be improved to around 30% (Biswas et al. 2013). This targeted copper grade is achieved through two stages of mineral processing. Firstly, the copper in the ore has to be liberated by crushing the mineral rock. Secondly, the liberated copper in the crushed ore is then physically separated from other minerals like nickel by froth flotation techniques."

Jan 1, 2018

By David Deglon, Martin Harris, Mehdi Safari

This paper investigates the effect of energy input on the flotation of galena in a novel oscillating grid flotation cell (OGC). Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Previous work was limited to quartz (-100 µm). Galena (-150 µm) was floated in the OGC at power intensities from 0.5 to 3 W/kg using 0.13, 0.58 and 0.82 mm mean bubble sizes (d10) and at three collector dosages. Results show that the effect of power intensity on flotation kinetics is strongly dependent on both particle and bubble size. For fine particles (-19 µm), increasing energy input increases the flotation rate at a low collector dosage but leads to an optimum at both the moderate and high collector dosages. For intermediate particles (+19-38 µm), increasing energy input has no effect on the flotation rate at the low collector dosage but leads to an optimum at both moderate and high collector dosages. For coarse particles (+38-150 µm), increasing energy input has no effect on the flotation rate at the low collector dosage and leads to a general decrease at both moderate and high collector dosages. Optimum conditions for fine particles are using small bubbles at a moderate collector dosage and an energy input of around 2 W/kg. Optimum conditions for moderate particles are using small bubbles at a high collector dosage and energy inputs of around 1.0 W/kg. Coarse particles do not benefit from agitation.

Jan 1, 2014

By L. A. Nemchinova, M. A. Arustamian

"For a long time tailings piles of mining and smelting complexes have met the eye being a prospecting feedstock source for many industries. Nowadays, 6.5 million tons of copper and cooper-zinc processing tailings are stockpiled in the Urals annually, as there is no technology of its processing to provide a full and complex metal extraction within mining and processing operations. In spite of large volumes of mining wastes, not more than 20% of annual overburden, approx. 10% of processing wastes, approx. 40% slags (1) are involved into processing.Based on today’s complex of economic, environmental and social challenges of ore processing, waste processing technology using existing capacities is a burning issue. Mining wastes characteristics (including fine dissemination, variability of physical and chemical properties of mineral surfaces under impact of oxidizing, leaching, etc.) predetermine challenges arising out of its involving into processing and justify high capital intensity of new construction or reconstruction projects followed by replacement of existing processing lines with new ones.In this paper, the authors propose flotation technology for mature tailings of copper, copper-zinc and polymetallic ore processing. The technology developed provides for upgrade of existing process flowsheet diagrams at minimum costs to produce additional saleable products including low-grade copper concentrate, saleable zinc concentrate and gold concentrate thus facilitates sustainable use of depleting minerals and operational efficiency due to cost-efficient processing of already mined materials, being in fact, final semi-products located near existing operations. This is particularly important for operations with standby capacities and not engaged workforce."

Jan 1, 2018

By Jiang Wenli, Zhang Yimin

In order to enhance the quality of iron concentrate from magnetic separation, reverse-flotation technology is often applied in an iron ore dressing plant.However, this technology has disadvantages in terms of operating cost,energy consumptionand environmental protection(Zhao, Wu& Wang,2005).Developing innovative equipment to process magnetite ore more-effectively is a way to get rid of these disadvantages of reverse flotation and improve the quality of iron concentrate.This paper describes the development of Complex Flashing-Field Magnetic Cleaner,a new kind of equipment based on the principle of combination of separation in magnetic field and separation in gravity field(Hao & Jiang, 2002).This innovative equipment possesses a tailor-made magnetic system and has the characteristics of a magneticfieldwhich can strengthen the formation of magnetic agglomerations and the dispersion of gangue mineralsto improvethe quality of separation.The automatic control system developed specifically for this equipment can further increase the accuracy of separation and stabilize the process.

Jan 1, 2014

By Xing Yang, Zhen Peng, Guangwen Zhang, Haifeng Wang, Yaqun He

"Triboelectric separation of ilmenite ore based on the tribocharge differences between ilmenite and gangue minerals was conducted in this study. Triboelectric characteristics of ilmenite and its associated minerals were studied using polyvinyl chloride (PVC), pentatricopeptide repeats (PPR), copper, polymethyl methacrylate (PMMA), stainless steel (SS), teflon and quartz glass (QG) tribochargers in lab triboelectric unit. Results demonstrated that the ilmenite particles tribocharged positively while gangue minerals tribocharged negatively using PVC as tribocharger. The particle size also has a significant effect on tribocharge, and the -0.125+0.074 mm is the optimal size fraction of triboelectric separation. Charge-mass ratios of minerals increase with the increases of tribocharging length, but the increasing rate gradually reduce. At 1.5 m tribocharging length, charge-mass ratios of ilmenite, quartz, feldspar and mica are up to 6.07 nC/g, -6.05 nC/g, -4.30 nC/g and -4.56 nC/g, respectively. Based on the triboelectric characteristics of each mineral, triboelectric separation of ilmenite was conducted, and the grade of ilmenite ore increased from 15.47% to 28.40%. INTRODUCTION As a transition metal titanium plays an irreplaceable role in medical, aerospace and materials due to its light weight, high strength and corrosion resistance. Pure titanium dioxide is an excellent white pigment and is widely applied in industries of paint and textile. Ilmenite is the main raw material for titanium industry. For the beneficiation of ilmenite, series methods have been proposed, such as the application of dry magnetic and wet gravity separations to separate the ilmenite from the zircon and rutile. Electrostatic separation is extensively used in the beneficiation of heavy mineral sands for the recovery of rutile, zircon and ilmenite while flotation is used to separate fine ilmenite (Mehdilo et al., 2014; Fan et al., 2014). Compared with flotation and gravity separation, electrostatic separation does not consume water, and native properties of materials will not be changed and energy consumption will be reduced (Wang et al., 2014). Thus, the wide application of electrostatic separation and other dry separation methods is a trend in separation and purification industry, especially in water-scarce areas."

Jan 1, 2018

By Lina Chica, Arturo Barrientos, O. Bustamante

Hydrocyclone is a device commonly used in mineral processing industry. Underflow control plays a fundamental role in hydrocyclone operation. This affirmation supports the fact that hydrocyclone underflow has effect in some aspects of separation performance like capacity, split ratio, cut size and bypass. Hydrocyclone operation state is associated to underflow characteristics: air core formation and discharge shape. Many studies attempt to understand size separation phenomenon and the discharge influence but none of them has taken an energy point of view. This work presents the results of a mechanical energy dissipation for hydrocyclone operation from a mechanical energy balance. The experimental results related to Newtonian suspensions show that underflow energy dissipation does not control the operation because this magnitude is small compared to interior energy dissipation. However, discharge energy dissipation provides enough information to describe underflow conditions and its influence in separation conditions. In the modelling non dimensional parameters have been considered for hydrodynamic description and for geometrical and operation hydrocyclone characteristics. Energy dissipation from the continua media approximation results into a relevant concept to understand the hydrocyclone performance and improve industrial installations.

Jan 1, 2014

By Ying Gu

Automated mineralogy methods and tools, such as the Mineral Liberation Analyzer (MLA) and the QEMSCAN, are now widely used for ore characterization, process design and optimization. Several case studies published recently demonstrate that large gains can be obtained through grinding and flotation optimization guided by automated mineralogy data. However, since automated mineralogy can only provide the information pointing to where the process gains can be made, it does not directly impact the production gain. Thus, a question is often asked: how to value the contribution of automated mineralogy to process improvement of a particular plant. This appears to be a difficult question. On close examination however, it is found that this is essentially a question of the value of information and it is reasonably well documented in various other industries. Hubbard (2010), in chapter 7 ?Measuring the Value of Information?, dealt with exactly this type of problem. The value of information is the reduced risk of an investment and opportunity loss. The methods Hubbard developed can be applied to estimate the value of automated mineralogy, as well as metallurgical test work, which also produces information that reduces the risk of investment. This paper first introduces Hubbard?s theory on the value of information and how to measure it. It then applies his methods to estimate the value of automated mineralogy, using Anglo Platinum?s fine grinding project as an example. In this case, the value of automated mineralogy includes the reduction in investment risk worth US$ 62.5million, in project rejection worth US$197 million and in opportunity loss worth US$320 million. In the end, a general model is developed to allow the simulation of the value of automated mineralogy in different mining operations constrained by different parameters.

Sep 1, 2012

By Andrew T. McBride, Malcolm S. Powell, Indresan Govender

"Current empirical Semi Autogneous Grinding (SAG) mill models contain assumptions concerning the amount of energy available for particle breakage, how this energy is distributed in the mill media and the rate at which the energy is transferred. Despite these assumptions the JK SAG model is highly functional with a proven track record. DEM provides a numerical framework to greatly improve on these assumptions that were necessary due to a lack of available input data.This paper identifies key outputs of the Discrete Element Method (DEM), such as energy spectra and impact probability distribution. It describes how they can be incorporated into current mill models utilising practical rock breakage data. The rate at which energy is transferred is shown to be dependent on particle position and mill rotational speed and not once per cycle as previously assumed. Based upon this an improved energy transfer methodology is presented. The fundamental outputs of the DEM are validated against experimental three-dimensional particle tracking data, so as to establish whether the DEM produces correct energy transfer predictions on the inter-particle level, which is crucial to this work. • Effective Experimental ValidationAn automated 3D tracking technique is employed to study the motion of plastic particles deep within the charge of a 142mm diameter experimental mill. A Biplanar Angioscope is used to film the mill with X-rays in two planes simultaneously at 50 frames/s, with a shutter speed of 1/3000s. A marked ball within the charge is tracked for over 2 minutes and the resulting digital images processed by a fully automated imaging technique, which locates the 3D coordinates of the particles to within 0.2mm. With over 250 circulations, this provides statistically rigorous and accurate data for verification in the numerical modelling of mills.A series of validation techniques have been developed to compare the experimental trajectory data with the outputs of both 2D and 3D DEM simulations. The techniques describe the shape of the charge and the particle motion within mill, allowing objective comparisons to be made of key features of the charge, such as the equilibrium surface and the centre-of-circulation."

Jan 1, 2003

By Cuim R., M. L. Li

Fankou Lead-Zinc Mine produced pyrite concentrate (P.C.) from the zinc tailings by rougher and scavenger flotation before 2010, with the averaged S grade of 40.54% at recovery of 79.34% ( to the feed of S circuit). On the one hand, the economic value of P.C. increases with its purity, on the other hand, when the S grade of P.C. feed to sulfuric acid manufacturer is over 47%, the pyrite cinder can reach a high Fe grade of 62% which can be directly sold as iron concentrate. On this background, engineers in Fankou Mine set the P.C. with S grade of 47% as target. The direct way to reach that goal was to clean the rougher P.C.. Lots of cleaning flotation tests were conducted and the compromised strategy was to produce two ranks P.C. with the S grade of 47% and 38% at the recovery of 44.20% and 36.17%, respectively. The dual-product flowsheet was successfully industrialized in 2010. In order to further improve the quality of P.C., gravity separation was introduced into the flowsheet. The numerical simulation and separation tests were performed to evaluate the beneficiation and classification performance of hydrocyclone as it treated the rougher P.C.. It was shown that the underflow of hydrocyclone could addressed the S grade of 47%, and the finer size overflow could also be enriched to P.C. with S grade of 47% by flotation, due to the contained pyrite with well liberation. That is to say, with the ingenious addition of hydrocyclone to treat the rough P.C., single P.C. with S grade of 47% could be achieved. The new flotation-gravity separation flowsheet was commissioned to produce the high quality P.C. at the end of 2013. The averaged S grade is 47.20% at recovery of 82.26% in 2014. The two steps flowsheet improvement maximizes the enterprise benefits and leads to simple utilization of Fe in pyrite in downstream industry.

Jan 1, 2018

By Sydney Mantsho, Toni Streczynski, Manuel Gonzalez

"In 2013, the commissioning of the MillStar Stabilisation and FloatStar Stabilisation and Optimisation controllers were completed at the Cerro Bayo Silver (Ag) mine in Patagonia, Chile. The MillStar control system has stabilised the feed to the SAG mill as well as the density at the discharge end of the SAG mill and ball mill. The FloatStar Stabilisation and Optimisation controllers have successfully stabilised and optimised the flotation circuit to ensure consistent product quality within desired specifications.The mill feed is controlled utilising the MillStar Solids Feed controller. Additionally, the solids to liquid ratio into the SAG mill was controlled utilising the Mill Inlet Ratio controller in conjunction with the Solids Feed controller. The discharge end of the milling process is a highly interactive and complex system. The use of a Robust Nonlinear Model Predicative Controller (RNMPC) was ideally suited to control this section of the process. On the Cerro Bayo milling circuit, the RNMPC was used to control the mill discharge sump level and the primary cyclone feed density to produce a more consistent feed to the flotation circuit.Three levels of the FloatStar control system were installed, for flotation stability, concentrate flow stability as well as grade optimisation. The Level Stabiliser was used to stabilise the level control on 6 flotation banks. The Flow Optimiser was commissioned on the Rougher, Scavenger and Cleaner concentrate sumps to stabilise concentrate flow from the flotation cells. The Grade Recovery Optimiser was commissioned on the Roughers section. A number of instrumentation challenges were identified which limited the overall benefit derived from the system. Once these were addressed, the performance was optimised. The overall benefit provided by the system was observed in terms of the improvements in Ag recovery."

Jan 1, 2014

By Kang N. Zhong, Hui H. Luo, Yi H. Wei, Yu L. Wang

"More than 85% of phosphorous reserves in China occur as middle-low grade phosphate of sedimentary origin. The main gangues are dolomite, quartz, silicates, and clays. The characteristics of minerals are finely disseminated. Flotation results have shown that the floatability of apatite of this kind of ore is much worse than that of igneous and metasedimentary origin because of its high specific surface area. Although some effective depressants, such as naphthalene sulfonate and phenanthrene sulfonate, are used to decrease the MgO content in the P2O5 concentrate, its presence is still high (about 2%) in the Chinese concentrates. Meanwhile, the wastewater may cause some environmental problems. Batch flotation results and measurements of specific surface area and CO3 2- have revealed that there is a relationship between the floatability of apatite and the surface area.A two-stage flotation flowsheet, which includes a combination of direct and reverse flotation, was developed for beneficiating sedimentary phosphate ores. The direct flotation was conducted in an alkaline medium and most of the apatite and carbonate minerals floated leaving quartz and siliceous gangue in the sink. In the reverse flotation circuit, the floated product was further beneficiated in an acidic medium to eliminate the carbonate as a float product. Apart from the high quality of concentrate, the two-stage flotation also facilitated the treatment and the recycling of wastewater. A wastewater recycling procedure was developed and tested in a continuous flotation process. The key factor was the careful selection of effective and non-toxic reagents."

Jan 1, 2003

By Charlene Gokhale

Geopolymerisation has emerged during the last few years as an industrial and ecological approach to construction and waste management. By utilizing waste materials and their reactive properties, it is now possible to create geopolymers systems that not only mechanically durable enough to be used as construction materials but are also potential stable immobilisation systems for toxic waste. Previous studies by Van Jaarsveld et al. (1997) and Van Jaarsveld et al. (1998) have reported on the numerous applications of geopolymers in the immobilisation of toxic metals. Research into the possible utilisation of geopolymers as an encapsulation media for organic waste has however been rare. This paper therefore provides an insight into the possible utilisation of geopolymers as a binder for hazardous organic materials.

Jan 1, 2003