Search Documents

By S. J. Lui

Sodium oleate was an effective diaspore collector, whereas chelate collector OL2 showed certain collecting power over diaspore and nonionic surfactant OL3 showed little collecting ability. Then experiments were carried out using sodium oleate as the main collector with the addition of OL2,OL3 to study the influences on diaspore flotation, it could be seen from the experiments that accelerants had a marked influence on the recovery of diaspore, which could be raised by 10%, and the addition sequence also affected the flotation behavior: the best results could be gained when the accelerants were mixed thoroughly before adding and the best ratio of collector OL1 and accelerant OL2, OL3 stood at 30:2:1. Based on the calculation of the ingredients in the sodium oleate solution, sodium oleate reacted with surface of the mineral and formed the acid-soap polymer [HOl?Ol-] when pH was about 9. Zeta potential test showed the accelerant promoted the absorption of collector on the mineral surface, which lowered zeta potential. As could be seen from surface tension experi-ments, the addition of accelerant OL3 lowered the CMC value of OL1 solution, which was equiva-lent to raise the power of the agents. Further Infrared Ray experiments showed the co-absorption of OL1 and OL2 make aluminum oleate on the mineral surface more stable. Up till now, the mixed reagents with sodium oleate as the main collector, combined with other two accelerants had been used in the Zhongzhou concentration plant, which is the first diaspore flotation plant in China.

Jan 1, 2014

By Luís Marcelo Tavares, Daniel Francioli, Malcolm Powell, Mohsen Yahyaei

"Mathematical modeling of the comminution process requires understanding of all breakage mechanisms occurring in this mechanical environment. Modeling of high energy impact breakage is well established, however, modeling low energy breakage including incremental damage breakage, attrition and abrasion is still under development. Free fall incremental impact tests were carried out to investigate the surface fragmentation of a copper-gold ore. This process was achieved by dropping particles individually from a height of four meters onto a metallic plate. The impact specific energy was 0.01KWh/t. The setting of the metallic plate was changed to test the impact angles of 0°, 45°, and 60°. Tests were carried out using fresh angular rocks as well as smoothed particles. Changes to the plate angle and particle shape enabled the study of the influence of the tangential component of the impact energy along with particle shape on superficial breakage. By studying the fractional mass loss variation in each impact, two distinct stages of surface fragmentation were clearly determined: high fractional mass loss dominated in the first 10 impacts and was attributed to chipping, whereas low fractional mass loss occurred for the remainder of the impacts and was attributed to abrasion. Smoothed particles demonstrated higher resistantance to breakage and their surface fragmentation behavior indicated a closer relationship to abrasion, especially when lower impact angles were used."

Jan 1, 2014

Micro-fine disseminated molybdenite was ground in a laboratory stirred mill using steel media and zirconium media respectively. The floatability of ground molybdenite and slurry chemistry was investigated. It was found that the total recovery of ground molybdenite using zirconium media was higher while the pH and Eh of the slurry are lower than that using steel media. When steel media was used, iron oxy-hydroxides had been generated coated on the surface of molybdenite, and decreased the floatability of molybdenite, especially of the -10µm particles. The iron and lead oxy-hydroxides was generated by the reaction between steel media with pyrite and galena associated with molybdenite. It was also found that changing the grinding media to inert can benefit the flotation of molybdenite. Keywords: stirred mill, grinding environment, floatability, micro-fine disseminated molybdenite, fine grinding

Sep 1, 2012

By C. Han

The analytical results of Dagushan grinding workshop primary grinding operation product show that the size fraction of -0.079mm is 32.88%, the size fraction of -0.01mm is 9.97%, the rate of -0.01mm size fraction and -0.079mm size fraction is 30.32%. It means that there is too much -0.01mm size fraction in primary grinding operation product and fall out that there will not be a better result in following operations. Several tests have been carried out to control the size distributing of the primary grinding operation product according to confirm the appropriate conditions of grinding operation. Integrate with theoretic count, grinding property tests show that the appropriate rev ratio of ball mill should be between 85% and 90% so as to get better size distributing. Based on the results of grinding property tests, the shocking property tests simulated the momentum of different diameter steel balls in the ball mill have been carried out. It showed that if want to get better size distributing the appropriate diameter of steel ball should be 110mm. The tests result shows that regulate diameter of steel ball and rev ratio of ball mill could control the size distributing. Contrast to the technical parameters of ball mill in grinding operation now, there are some significant advices are given for practice and industrial tests.

Jan 1, 2014

By V. V. Lodeischikov

This paper covers some problems of treatment of complex gold ores and concentrates containing copper, lead, zinc, antimony and uranium. All these metals may present in ores both as major and associated components. The paper suggests recommendations for early determination of relative value of the metals in ores, which largely contribute to the selection of concentration and metallurgical flow sheets. The focus of this work is on treatment of complex ores in gold plants. The metal extraction technologies used by such gold plants are typically aimed at maximum gold recovery. Therefore, production of base metals as by-products requires significant updating of the existing process flow sheets based on economic, environmental and other considerations. At the same time, cooperation between gold plants and base-metal plants is of great importance. This paper provides an overview of worldwide existing and innovative processes of base metals extraction from complex and refractory gold ores.

Jan 1, 2014

By D. Saramak

The comminution technology based on High-Pressure Grinding Rolls presses (HPGR) application is currently one of the most efficient methods of hard ore comminution from the scope of the energy consumption and the development of industrial HPGR applications in ore preparation circuits is presently the world trend. However, even though the technology is already in use in many countries, which are the leaders in application of modern mining technology, there is still lack of base investigations over the HPGR performance. Throughput and energetic models of HPGR performance are quite well developed, but technological models predicting the comminution effects still needs an in-depth research. In the paper authors present the method of modeling of HPGR products? particle size distribution with using of suitable mathematical models. A basis of the HPGR performance assessment and HPGR-based crushing circuits design is a product?s particle size distribution. In order to precisely determine the particle size distribution of a HPGR product, parameters of product?s particle size distributions should be conditional on the main technical parameters of the roller press like operating pressure and the speed of rolls. The most accurate approximation of a distribution of size particle d appeared the Weibull?s truncated distribution and it is possible to obtain significant relationships between the approximation formula and the value of operating pressure, or feed characteristics. It makes possible a determination of mass recoveries of the product?s respective size fractions and the productivity planning. Instead of pressure (P), the other HPGR operating parameters can be applied, but the P value appears to produce the most relevant relationship. Keywords: HPGR, comminution, particle size distribution, ore processing

Sep 1, 2012

By T. Wang

A new kind of mixed chelate collector was prepared in order to separate gangue (mainly quartz) and iron minerals efficiently during room temperature. The collector was was composed of two chelate collectors DES and DA. Floatation tests were carried out under 28?C with mixed magnetic concentrates of Donganshan sintering plant, and optimal test conditions were obtained, in which a direct floatation was undertaken and then a close circuit reverse floatation tests ( one roughing, one cleaning, and two scavenging), and a result of Fe grade of siderite concentrate 36.49%, Fe recovery of siderite concentrate 10.65%, Fe grade of final concentrate 66.27%, Fe recovery of final concentrate 78.25%, and Fe grade of tailing 16.22% was gained. Fourier Transform Infrared (FTIR) Spectra and Zeta potential of siderite and quartz adsorbed the DES and DA collectors before and after were measured in order to analyze the reaction between the collector and minerals. Furthermore, Molecule electronegativity of DES and DA was calculated by Electronegativity Proportionality Principle (EPP). Results showed that DES molecules have five active adsorbing sites and their molecule electronegativity was stronger while DA molecules have three active adsorbing sites, which all make the mixed collector has efficiently collecting performance. Zeta potential results of Quartz and siderite showed that at pH 11.5 both kinds of particles charged negative and at this pH value the mixed collector were mainly anionic collectors which indicate that electrostatic adsorption does not exist at this situation. FTIR results showed that characteristic peaks of the mixed collector changed before and after adsorption with the minerals, which means that there exists chemical adsorption or hydrogen bonding.

Jan 1, 2014

By F. Karakas

Organo-bentonite production enjoys important applications including solvent based paints and, more importantly, the production of polymer/bentonite nanocomposites. Quarternary ammonium salts in this regard are still considered as the most versatile reagents in the process of hydrophobization. In this study, a purified form of Resadiye region bentonites, which is one of the most significant sodium bentonite deposits in the world, was used. The raw Na-Bentonite was typically characterized by chemical analysis, XRD and DTA analysis and more importantly for its cation exchange capacity (CEC). Other technological properties such as swelling index, pH, apparent viscosity, water absorption, oil absorption were also conducted on the raw bentonite. The mineralogical analysis of the raw bentonite reveals that it contains about 80 % montmorillonite together with other associated gangue minerals including feldspar, quartz, calcite, dolomite, coloured impurities and other clay minerals. The raw bentonite was subjected to two stage processing involving a series of hydrocylones. Different apex and vortex diameters and different pressures were employed in order to produce a bentonite concentrate with 95 meq/100g CEC from a CEC of 71 meq/100 g. This high quality concentrate was used in the production of organo-bentontonite. The modification was performed with two different quaternary amines, i.e. Trimethyl Phenyl Ammonium Chloride (TPAC) and Hexadecyl Trimethyl Ammonium Bromide (HDTMA-Br). In the modification procedure, three parameters, i.e., adsorption density, zeta potential, swelling index and apparent viscosity were studied simultaneous-ly from the same suspension to identify both the mechanism of the process and also the degree of hydrophobicity. Adsorption measurements were made as a function of conditioning period, pH, and reagent concentration. Simultaneous examination of the adsorption density, zeta potential and apparent viscosity enabled us to pinpoint the optimum region of hydrophobicity which was subsequently tested by settling and critical coagulation concentration in both water as polar and toluene as nonpolar solvents. The results are analyzed in the light of experimental data.

Jan 1, 2014

By Yosep Han

Mechanically-induced chemical reactions between natural beach ilmenite (FeTiO3) and silicon (Si) have been examined by a combination of X-ray diffraction (XRD) and scanning electronic microscopy (SEM) analyses. The effect of various milling time on the phase transformation, crystallite size, and lattice strain of a beach sand ilmenite with silicon, and on their leaching behavior in hydrochloric acid (HCl) has been investigated. For mechanically activated FeTiO3, the crystallite size decreased and lattice strain increased monotonically with time of milling. However, the mechanochemically synthesized ilmenite with silicon showed a relatively smaller crystallite size and greater lattice strain compared with the mechanically activated ilmenite under the same milling condition. In accordance with the elapse of milling time, the intensity of both pure FeTiO3 and mechanically activated FeTiO3 gradually decreased. However, in case of the mechanochemically synthesized ilmenitereduction of FeTiO3 by silicon resulted in formation of rutile TiO2 at the milling time of 20 h and afterwards. Additional leaching experiments were carried out at an HCl/ilmenite (wt%) ratio of 20:1. The concentration of HCl was 3 M and the reaction temperature ranged from 70 to 90 oC. Mechanical activation was observed to significantly enhance the dissolution rates of both iron (Fe) and titanium (Ti) in HCl. Particularly, effects of both milling time and silicon addition on the dissolution rates of titanium and iron were significant, while those of temperature were relatively minor under the conditions investigated in this study. Keywords: mechanochemical treatment, natural beach ilmenite, silicon, leaching behavior

Sep 1, 2012

By F. M. Zafar Kaifi

Magnesite producing companies rely on high grade purity MgO. The mineralogy of magnesite has a significant impact on the manufacturing of magnesite bricks. The manufacturing process of bricks companies utilizes 90% magnesite from 85%~90% MgO. The main objective of the magnesite bricks was to utilizes the indigenous raw material available in bulk quantity. With better under-standing of chemistry of the mineral species and strict control of bricks manufacturing/processing conditions can be better produce efficiently, a low cost high quality bricks with minimum detrimental environmental impact.

Jan 1, 2014

By Rogerio C. Guimarães, Antonio E. C. Peres

The production of phosphate concentrates (phosphate rock) from slimes represents a challenge to the phosphate industry worldwide. In Brazil, this challenge is particularly relevant due to the consistently low P2O5 grades and the igneous origin. The Brazilian phosphate deposits are made up mainly of apatite from alkaline chimneys, representing 80% of the Brazilian reserves; phosphorite deposits contribute 18% and the other sources (guano, phosphorous bauxite, and apatite from veins) reach 2%. The Brazilian industry beneficiates phosphate ores that are mineralogically more complex than those treated elsewhere. The low apatite grade, inherent to the igneous Brazilian ores, added to the mineralogical complexity due to the weathering of the rocks, has represented a permanent challenge to the Brazilian process engineers. The total measured, indicated and inferred reserves reach 3.2 million tonnes of ore with average grade 11% P2O5. The development of local technology for phosphate beneficiation started in the 1960’s. The first industrial experiences of producing phosphate rock from slimes (-44µm or -325#) fraction started at Arafertil, currently Bunge Fertilizantes SA, in Araxá, in the 1980’s. This production corresponds, nowadays, to 35% of the total production of concentrates in the company (830,000t/year) in a circuit consisting of desliming in 40mm microcyclones and concentration in flotation columns, corn starch and fatty acids being utilised as reagents. The performance of slimes flotation and the process control, at Bunge´s concentrator, were improved after the introduction of column flotation technology, in the first half of the nineties. The column flotation technology for slimes recovery was expanded to other Brazilian concentrators still in the nineties: Ultrafértil (Catalão – GO), Bunge (Cajati – SP), Fosfértil (Tapira – MG) and Copebrás (Catalão – GO). At present the Brazilian production of phosphate rock is approximately 4.5Mt/year, with a strong trend for a market increase. Genuinely Brazilian technology is utilised for the processing of slimes, the concentrates representing 11 to 13% of the overall production. The production of apatite concentrates from slimes was relevant to increase phosphate recovery and reduce costs, contributing to the growth of the fertilisers industry.

Jan 1, 2003

By A. Mainza, I. Govender, J. Waters

"The study of the properties of mineral processing suspensions is important in understanding how a circuit might behave. As soon as the predominantly dry ore enters a wet milling stage the ore properties undergo changes as a ‘slurry’ is created. Slurries can be classified in terms of their physical properties (particle density, solids concentration, particle size and size distribution, particle shape), and their flow properties such as rheology. Slurry flow regimes are classified into true homogeneous, pseudo homogeneous, heterogeneous and fully segregated, and only true homogeneous and pseudo homogeneous suspensions can be characterized by their flow structure. A class of the heterogeneous regime are the so-called dense phase or settling slurries - those which result in a clear water surface on standing, although they may approach a pseudo homogeneous state if suspended for a sufficient period of time. They are usually extremely difficult to characterize by their rheological properties alone and the rheological characterization of these slurries has always posed a problem, especially at higher concentrations. Previous rheological studies have focused on the individual concentrator units dealing with milling, classification, pumping, flotation, fine grinding, thickening.In this work an attempt was made to characterize two ore types (copper and a Platreef platinum ore) using a custom built Paterson and Cooke tube rheometer, at concentrations up to 43% by volume. After applying a turbulence correction, results showed Bingham plastic behavior. A conventional vane rheometer was then used to compare the rheological behavior of platinum concentrator streams. A size criteria was used to identify any rheologically dominant streams."

Jan 1, 2014

By S. Martins

The aim of this work is to compare three different results of charge motion in a modified 5ft diameter lab mill and to identify differences and similarities in these results. The lab mill is modified from tumbling a ball charge to tumbling a charge of disks. This modification replicates 2D motion. This 2D condition is measured using an instrumented disk (iDisk) and analysed using a video imaging system. The iDisk is equipped with a 3D accelerometer array and rotation rate sensors. With the help of a video system, some measured quantities are also determined externally. The results of these three predictions or measurements are presented. A discussion is included.

Jan 1, 2014

By Longjiang Li, Mao Jiang, Zhihui Shen, Guizhou University, Yin Pan

This paper aims to study the influence and action mechanism of collector Y-89 on the flotation of auriferous pyrite. The measurement to identify adsorption quantity, IR and XPS spectrum analysis and flotation experiment made on the pure mineral were conducted. The research results show that when the dosage of MIBC is 20 mg/L, and pH of 8, the dosage of Y-89 over 60 mg/L, the pyrite recovery rate is greater than 80%.And when the dosage of Y-89is 60 mg/L, dosage of MIBC 20 mg/L, the pH in a wider range (pH=4~9), the recovery is greater than 75%. When the pH is above 10, the pyrite is depressed and its recovery rate is found to be dramatically dropping. Adsorption quantity measurement also shows that the strong alkaline conditions inhibit the adsorption of Y-89 on the surface of auriferous pyrite. IR measurement indicates that chemisorption of Y-89 occurs on the surface of auriferous pyrite. XPS spectrum analysis indicates that without adding Y-89, oxidation reaction occurs on the surface of pyrite. But when Y-89 is added, the chemical environment of Fe on the surface of pyrite has changed. Such findings indicate that with Y-89, chemisorption occurs on the surface of auriferous pyrite.

Jan 1, 2014

By Arkady Senchenko, Yevgeny Zhagun, Yury Kulikov, John Starkey

"The paper contains description of a new project in Russia - gold-processing plant at Aleksandrovskoye deposit (start up in September, 2013). The paper includes a brief description of plant flowsheet, data for material composition and technological properties of ore, as well as information about the achieved parameters of ore processing over the first months of plant operation. The project is interesting because a new semiautogenous mill and a ball mill were purchased on the basis of SAGDesign Consulting Group recommendations after the testing of ore samples characterizing the deposit according to specific years of operation. The plant has relatively small design capacity - 750 000 tpa, but nevertheless is the biggest gold-processing plant in the territory of Zabaikalsky region. Major valuable component in the ore is gold, silver is recovered as a by-product. The ores are very hard to grind. The design grinding flowsheet includes a semiautogenous mill operating in closed circuit with a screen, and a ball mill operating in a closed circuit with hydrocyclones (SAB). Process technology includes gravity processing and flotation with subsequent cyanide leaching of concentrates. Mill operation analysis and conclusions about the compliance of the achieved values to target ones are shown, as well as the accuracy of SAGDesign method when applied to very hard ores of Aleksandrovkoye deposit are presented in this paper. Basic directions of technological flowsheet optimization are also given."

Jan 1, 2014

By Stoyan Gaydardzhiev, Michel Shengo, Pierre Kalenga

Lab-scale flotation of copper and cobalt oxidized ore from the Luiswishi deposit in the Katanga province (DRC) has been done focusing on the influence of the degree of process water recycling on metals recovery. Results have shown that at 20 % recycling rate, the recovery of copper and cobalt in the cleaner stage have been respectively reduced to 23 % and 45 % in comparison to 53 % Cu and 63 % Co if process water has not been recycled. At 10 % recycling rate however, the system could still tolerate the effect from recycling, since Cu and Co recovery has remained respectively at acceptable levels of 52 % and 60 %. In order to explain the reasons for the observed worsening of flotation results if process water was recycled at rate higher than 20 %, electrochemical investigation of the pulp has been performed. It has been established that the chemical compounds formed in the pulp when process water was recycled, do influence the sulphidization of malachite and heterogenite and impact further collector adsorption. To confirm these assumptions, the effect from thiosulphate ions presence during the sulphidization of high purity malachite has been studied. It has been found, that thiosulphate ions depending on their concentration in water induce variations in pulp properties such as DO content, pH, Es and contribute to formation of undesirable chemical compounds on mineral surface as identified by DRIFT spectroscopy.

Jan 1, 2014

By Gábor Mucsi, Barnabás Csoke, Viktor Mádai, Zoltán Molnár, Viktor Török, Ádám Rácz

The application of the stirred media mill in dry mode came to the front only in recent years, but at the same time several questions arise, such as aggregation, agglomeration, sticking on the liners and the grinding media. During high energy milling, not only the particle size reduces, but among others, in numerous cases the crystal structure and the amorphous state of the material also change due to the mechanical activation taking place. The present paper deals with experiments carried out on the ultrafine fly ash grinding in dry mode at various grinding conditions in a stirred media mill to investigate the mechanochemical effect and the energy efficiency of the mill. During the experiments the particle size distribution, particle shape, specific surface area, amorphity and crystal structure of the products were examined. The product related stress model was used for the evaluation of the effect of milling parameters on the mechanical activation. It was found, based on the experimental results, that there is mechanochemical effect on crystal structure of fly ash in the stirred media mill, as it was revealed by X-ray diffraction and FTIR measurements. The experimental results made it possible to determine the effect of the rotor circumferential speed and so the stress intensity on the mechanical activation of fly ash could be revealed.

Jan 1, 2014

By Zhu Yangge, Hu Xiaoxing, Feng Qiming, Zhang Guofan, Zhang Xingrong

"During the flotation process of ilmenite and titanaugite with fatty acid as collector, unavoidable ions such as Ca2+, Mg2+, Al3+, Fe3+ and Fe2+ demonstrate considerable influence on the floatability of the minerals. In this study, flotation test, zeta potential test, and solution chemistry calculation were adopted to investigate the mechanism of how these metal ions affect the floatability of ilmenite and titanaugite in different pH conditions. The results show that in weak acidic solution, Ca2+ and Mg2+ mainly freely exist in the solution with little adsorption on mineral surface, and their reaction ability with oleate ions is weaker than active site on ilmenite surface (Fe), thus they show negligible effect on the flotation of ilmenite; Al3+ shows similar reaction ability with oleate ion compared to Fe3+, which lead to competitive reaction with collector, so the flotation of ilmenite is depressed. While Fe3+ can adsorb on surface of titanaugite in the form of Fe(OH)3, and it shows stronger reaction ability with oleate ion compared with active site on titanaugite surface (Ca and Mg), which proves an activation effect on titanaugite flotation. In alkaline solution, all these five kinds of ions can adsorb on titanaugite surface, and the floatability of titanaugite will be activation. Based on the above analysis, it can be deduced that in the flotation system using fatty acid as collector, the adsorption of metal ions on mineral surfaces and the stronger reaction ability with collector than active site on mineral surfaces, are the two prerequisites for metal ions show activation effect on mineral flotation.INTRODUCTIONIn flotation pulp, the existence of metal ions is often inevitable. There are two sources for these metal ions: the first part is generated in grinding and flotation process due to the oxidation, reduction, corrosion or dissolution of minerals or grinding medium; the second part is from the flotation water or the addition because of the technology need. The metal ions in the pulp have a considerable influence on mineral flotation. Earlier researches are focus on the activation effect of mineral floatation by metal ions to obtain a higher flotation efficiency, many effective activators were found, such as Cu2+ activated sphalerite, Pb2+ activation wolframite, and Ca2+ activation quartz flotation, these metal ions have become the commonly used activators in industrial production. And many studies attempted to explain the mechanism of how metal ions affect the floatability of minerals. James (James et al, 1972) suggests that metal hydroxide precipitation is the main component leads to activation effect, while the study of Fuerstenau (Fuerstenau, 1976) showed that the metal ion hydroxyl complexes played significant role. In recent years, the reuse of mineral processing wastewater has attracted more attention (Rao et al, 1989; Liu et al, 2013; Wang et al, 2014), as a main component in flotation wastewater, the influence of “unavoidable ions” on flotation process still need in-depth study."

Jan 1, 2018

By V. Tsyplakov

This article reviews factors of preg-robbing effect, occurring in the course of pressure oxidation of ore and concentrates, containing chloride compounds and so-called 'organic carbon'. The article also summarizes the main results of the studies and testwork conducted to overcome this effect. The following efficient preg-robbing mitigation methods have been noted: higher temperature of pressure oxidation process, preliminary removal of natural carbonaceous material from concentrate, chloride removal prior to concentrate pressure oxidation, and addition of water-soluble organic blanking agents, which suppress the adsorption activity of the native ore adsorbents. Keywords: preg-robbing, double-refractory gold concentrates, pyrite, arsenopyrite, blanking agents, pressure oxidation, autoclave leaching

Sep 1, 2012

By H. D. Yu

In this paper, an evaluation about the process mineralogy of the rich iron mine in Mongolia with comprehensive methods is given; this provides foundation of the comprehensive recovery of iron and cobalt in the ore. The research shows that the iron?s grade is 61.23%, Co?s grade is 0.02%, the ore is rich iron ore and its Co content also reaches border mining grade. For the ore, if want get high grade iron concentrate powder, must identify the mineral composition and the occurrence of iron and take into ac-count the recovery of Co content as associated resources. Chemical phase analysis results show that 86.35% of iron exists in magnetite, which means that the theoretical recovery ratio of iron is close to 86%. Minerals spectrum analysis confirmed that the magnetite containing a small amount of Mg, Al, and other impurities, the actual iron minerals to 70.28%, which means that theoretically iron grade iron concentrate only close to 70.28%. Based on the result of iron chemical phase analysis, by investigating the liberation of sulfide minerals and gangue, the recovery index of iron can be forecasted, when grinding fineness is 35%, 45%, 55% and 65% bellow 0.074mm,theoretical content of Fe in iron concentrate separately is 67.71%,67.88%,68.78%,and 69.43%,accordingly the theoretical recovery of Fe is 87.38%,87.05%,86.92% and 86.63%. From the perspective of process mineralogy, the forecast mineral beneficiation indicators show that the ore is easy sorting ore, iron processing operations have higher recovery rate, but wants sorting of high-grade iron ore concentrate still need appropriate grinding fineness. Furthermore, associated element Co, existing mostly in pyrite and pyrrhotite, is valuable in the ore. Pyrite and pyrrhotite have ideal liberation under grinding, so cobalt can be easily enriched in sulfide concentrate.

Jan 1, 2014