Search Documents

By Q. X. Li

The state discharge standard for arsenic-containing wastewater which is the first kind of pollution is less than 0.5 mg/L. In fact, in a certain company, the acidic arsenic-containing wastewater in non-ferrous smelting was as high as 860 mg/L, which is far beyond the state discharge standard. Obviously, the direct release of this wastewater without further treatment would result in great hazards to the ecological environment. To aim directly at the characteristics of acidic arsenic-containing wastewater, in this study, two steps of treatment including oxidation-flocculation and removal fluoride by mixing alkaline neutralization were suggested. Through analyzing various influencing factors in treatment effects, the optimum technical conditions were obtained. The sediments after treating were recyclable and the secondary pollutions can be avoided. Moreover, the results also show that, all indexes of the effluent after treating are lower than the First Grade Standard of Integrated Wastewater Discharge (GB 8978-1996). This novel method has advantages of short flow sheet, easy operation and low cost.

Jan 1, 2014

By S. V. Petrov

In recent years, heap leaching of gold is becoming wide spread due to low capital and operational costs that allows economically feasible processing of low-grade and cut-off grade ores. Currently, over 30 heap leach projects are operated in Russia. Some of the deposits treated by heap leach methods are almost depleted. Therefore, they will soon require spent heaps detoxification and reclamation. Traditionally, spent heaps are detoxified by chemical treatment. This process is characterized by relatively high kinetics and requires expensive reagents and additional equipment. The main disadvantage of this process is secondary contamination of the solutions by products of detoxification reactions and impurities contained in reagents. If there is enough time, spent heaps can be detoxified by natural degradation. The advantages of the proposed method are low operational costs due to use of existing heap leaching facilities and eliminating the need for chemicals for spent heaps detoxification. Residual concentrations of cyanides and thyocyanates in liquid phase (wet ore) of spent gold ore heaps after detoxification were 0.2~0.3 mg/L. Heavy metals were almost completely removed. The method was successfully used for detoxification of spent heaps at two gold mines.

Jan 1, 2014

By Henrique Kahn, Daniel Uliana, Carina Ulsen, Guilherme Nery

"Gold has been a material in high demand since the dawn of humanity. After hundreds of years of exploitation, the increasingly search for gold occurs in lower grade deposits with greater extraction difficulty. Therefore, for maximum efficiency, deep knowledge of the characteristics of these minerals and their associations is crucial, which is acquired through an accurate and rigorous routine of process mineralogy and batch extraction tests. The industrial gold process extraction occurs by gravity concentration, sulphides flotation and cyanidation. For gravity concentration, it is fundamental to establish the proportion of free or coarse gold grains and its association to heavy minerals; regarding flotation, the most relevant data are the proportion of gold associated to sulphides and their liberation by the surface area; for cyanidation, it is crucial to evaluate gold accessibility and the kinetics of leaching. Thus, the characterization of gold associations and liberation is vital to establish the plant design, to optimize operating plants and to reduce gold losses. Our aim is the characterization of gold occurrence in low-grade Brazilian deposits with complex mineralogical assemblages to support processing flowchart definition and to predict metallurgical recoveries. Gold distribution in light and heavy minerals was evaluated by heavy liquid separation and the occurrence of gold in free or locked particles was carried out on heavy products by SEM-based automated image analysis using the MLA system. All the products of heavy liquid separation were cyanidated in head samples with different milling conditions to evaluate the reaction kinetics and maximum recovery."

Jan 1, 2014

By Y. H. Zhang

Mechanism of BK501 in desiliconization from bauxite was studied by use of flotation test, EDS, ?-potential, FTIR. Results of flotation show that almost all of diaspore can be depressed when BK501 is put into pulp ranging from pH 4~12, in the meanwhile kaolinite is slightly activated. In the light of surface analyses, it is concluded that the adsorption of reagent on the diaspore is dominant by chemical interaction. Moreover, kaolinite may float more by addition of BK501 because of flocculation.

Jan 1, 2014

By X. M. Yu

A large amount of polluted sludge is produced by a nonferrous metal factory after treating waste water with lime/ferrous salt. The concentration of arsenic in the dried sludge is high to 5.84%, a toxicity test is taken on the sludge according to GB5085.3-2007 and the extraction content is 15.75mg/L, which surpasses the arsenic extraction standard [As]=5mg/L, the sludge is categorized as hazardous waste. If put outside without disposal, it would be very harmful to environments. Here we report an optimum protocol to extract arsenic; S2- alkaline liquor is utilized to treat the arsenic sludge. At 85?, 10L 7% S2- liquor is added into 1kg dried sludge and the resulting mixture is stirred for 120min at 250r/min, then separated by centrifugation and the compressed waste residue dried naturally. The average arsenic content is 1.40mg/L, lower than GB5085.3-2007 Standard and arsenic-free residue is consistent with GB18598-2001 Standard, which can be bury safely. The extracted arsenic is transferred into copper arsensite for use as addictive in copper electrolysis and the waste water can be recycle after calcium is removed.

Jan 1, 2014

By Kevin Davey, Liza Forbes, Leanne Smith

Given the global scarcity and value of potable water, interest in the use of water of lower quality in mineral processing has grown significantly in recent years. Previous laboratory batch flotation tests conducted at CSIRO have shown that chalcopyrite floats strongly without collector in distilled water and that the collectorless flotability of chalcopyrite is unaffected by the use of brackish water, sea water or hypersaline water. In contrast, bornite is moderately flotable without collector in distilled water but all three lower-quality waters have a detrimental effect on the recovery of bornite. The depressant effect is so strong that the little recovery achieved in these waters was only slightly above what might have been expected from entrainment alone. This work has now been extended to another important copper sulfide mineral, chalcocite. In contrast to chalcopyrite and bornite, chalcocite does not exhibit collectorless flotability so the chalcocite tests in this study were performed in the presence of a standard collector (potassium ethyl xanthate). The results reveal that chalcocite is flotable with xanthate in distilled water but the lower-quality waters have a detrimental effect on the recovery of chalcocite. This effect is partly reversed by increase collector additions. Further tests were completed in order to investigate the effect of the different ions present in the saline waters on chalcocite flotation. Possible reasons for the observed differences are discussed in terms of the pulp chemistry of the system.

Jan 1, 2014

By Michael. H. Moys, Clayton Bhondayi

An electro-resistive measuring technique developed by the authors was used to study the effects of superficial gas velocity and froth height on froth phase bubble sizes as a function of height above the pulp-froth interface. Flotation tests and the bubble size measurement were carried out in a laboratory mechanical flotation cell that was operated in a pseudo-steady state mode using primary rougher tailings slurry from Lonmin Platinum as feed. The values of intra-bubble impact distances (IIDs) which are the estimates for froth phase bubble sizes obtained from the measurements indicated that as superficial gas velocity was increased, the values of IIDs decreased for the two froth depths tested. Increasing froth height at fixed gas rate resulted in an increase in IID values especially close to the froth surface. Changing froth height and gas rate alters froth residence times; longer froth residence times mean more time for bubbles to coalesce hence larger values of IIDs and vice-versa.

Jan 1, 2014

By Jorge Menacho

"A typical Chilean producer in the Large Copper Mining Industry today is characterized by high production level with economical results decreasing but still attractive. Operational activities are developed within a low-productivity environment, with high cost and complex relationship between the company and communities, government authorities, providers, clients and their own workers. Decreasing copper grades and limited availability of energy, water and workforce are structural problems which require the State intervention in collaboration with the relevant actors and benefits would be evident in the middle or long term. Main opportunities in the short term are found in the sub optimal conditions we have at many plants today. Robust solutions to control existing operational management system as well as to supply systematic optimization options are needed. These should be oriented toward effective fulfillment of specific operational set points and also to reduce variability in crosscutting tasks. Solutions should include easy connectivity to existing information systems as well as to a suite of simulation and optimization tools settled in a highly interactive communication platform. Relevant issues include minimization of specific energy and fresh water consumption, maximization of the use and performance of critical equipments, minimization of damage to environment and control of effective application of good operational practices. Several specific examples are given."

Jan 1, 2014

By F. Y. Kang

There are rich resources of natural graphite in China. It would be a good opportunity to upgrade national graphite industry if natural graphite with modification is used in lithium ion battery. Micro-crystalline graphite in high purity was coated with a carbon film on the surface. The initial cycle efficiency was improved to be 89.9% and cycle stability was remarkably improved. The experiments proved that microcrystalline graphite with carbon coating have excellent electrochemical performances at low cost as anode materials for lithium-ion battery. In addition, H2SO4-GIC technique was used to prepare the natural flake graphite powders with mild-exfoliation. Sub-micro and nano pores were found in the graphite samples. In correspondence the reversible capacity, rate capacity and cycle life were improved, which would meet the demand of high-power lithium-ion battery. Natural graphite is the most promising anode material for large-scale lithium-ion batteries. The demand of modified graphite grows up greatly in the market. Microcrystalline graphite with surface coating and flake graphite with mild-exfoliation are the promising commercial anode materials for the industry of lithium ion battery.

Jan 1, 2014

By Ibrahim Alp, Duygu Dinç, Ersin Yazici, Adularya Energy and Electricity Generation and Mining Inc., Oktay Celep, Haci Deveci

Thiosulfate leaching as an environmentally benign alternative to cyanide leaching has received particular attention in recent years. Most studies have focused on thiosulfate leaching of free milling ores and, to some extent, pregrobbing ores. In this study, leaching of gold from the refractory Kaletas ore (in which gold/silver alloy is the only mode of occurrence detected) in ammoniacal thiosulfate solutions was studied. A two-level full factorial design (23) was adopted to investigate the effects of concentration of thiosulfate (0.2-1 M Na2S2O3), ammonia (0.5-1 M NH3) and copper (0.05-0.1 M CuSO4) on the extraction of gold from a ground ore (-38 µm) over a period of 24 h. Statistical analysis confirmed the leaching of gold improved with increasing concentrations of thiosulfate and ammonia. In contrast, increasing the concentration of copper in the range tested adversely affected the extraction of gold. The magnitude of effects of parameters on the gold extraction was in the order of Na2S2O3 > NH3 > CuSO4. The maximum extraction of gold (69.6%) was obtained in the presence of 1 M Na2S2O3, 1 M NH3 and 0.05 M CuSO4. The negative influence of copper on gold extraction is most likely attributed to the decomposition of thiosulfate catalyzed by copper. Concentration of thiosulfate was also identified to be statistically the most important parameter for its consumption.

Jan 1, 2014

By P. Radziszewski

In comminution research, ore breakage and wear are usually studied independently of one another. Much of this is due to the fact that wear is usually a slow process compared to ore kage. However, the abrasion wheel test used to determine the abrasive wear contribution to total steel media wear provides the opportunity to study not only abrasive wear and friction but also ore breakage. In this paper, we will explore the use of the abrasion wheel wear test device to study abrasive wear, friction and ore breakage using standard Ottawa foundry sand. We will look into the feasibility of applying the work index as well as t10methodologies to this test set-up. We will also look at how the work index results evolve with abrasive wear and friction. We will then discuss the merits of pursuing the use of this abrasion wheel test for not only wear characterization but also breakage characterization.

Jan 1, 2014

In this paper, the recovery of copper minerals and molybdenite in the rougher/scavenger banks of two separate mineral processing plants is compared with recovery in laboratory (batch) cells. A number of metallurgical surveys were conducted in two plants treating porphyry copper and molyb-denum ore. Batch flotation tests were performed on plant conditioned flotation feed slurry, in parallel with the plant metallurgical surveys. The effect of flotation feed density on recovery of copper minerals and molybdenite in the plant and batch laboratory cells was investigated. Changes in flotation pulp density had little effect on copper mineral recovery, in both plant and laboratory cells. The ultimate recovery for molybdenite, on the contrary, increased considerably when the pulp density was reduced, both at plant and laboratory scale. Recovery of copper minerals in the plant and laboratory cells was comparable, while molybdenite recovery in laboratory flotation cells was 3%~13% higher than in plant. It is hypothesised that the flotation rate of molybdenite is sensitive to cell hydrodynamic conditions (i.e. local turbulent energy dissipation) more than the flotation rate of copper. The flotation behaviour of molybdenite particles is likely to be predominantly controlled by bubble-particle collision frequency, which is enhanced in high local turbulent energy dissipation environment. For chalcopyrite, the flotation recovery is mostly determined by attachment and stability efficiencies. An increase in local turbulent energy dissipation, while increasing collision efficiency, may negatively impact on attachment and stability efficiencies. The outcomes may have a considerable impact on increasing molybdenite recovery from porphyry ores.

Jan 1, 2014

By A. P. Liu

Semi-industrial test on fine products of Meishan dressing plant was carried out with type RP80/25 high pressure roller mill produced by Homburg Corporation of Germany, and the influences of such factors as energy consumption, water containing, throughput and circulating load on rolling effect were investigated. Closed circuit experiment result showed that Meishan iron ore could be suitable for powder grinding with high pressure roller mill, and energy consumption of the operation was declined by 25%~30%, which was favorable for energy-saving, increasing production efficiency and improving grinding effects. According to above experimental results, this paper put forward the technical proposal of application of high pressure roller mill in Meishan, and pointed out some technical problems which needed to be settled urgently in technology disposal.

Jan 1, 2014

By X. L. Wang

Hydrothermal method was applied in the preparation of calcium sulfate whiskers in airtight re-actor using gypsum as primary materials. The optimum conditions of preparation are as follows: pH value 9.8~10.1, concentration 5%, material size 18.1µm, which were determined by the analysis of the diameter of CaSO4 whiskers through SEM. On these conditions a product of ultrafine CaSO4 whiskers with diameter of 0.19µm and aspect ratio of 98 is obtained. Ultrafine CaSO4 whiskers with different concentrations, modified by titanate NDZ-401, were added into polypropylene as intensifier and composites of Ultrafine CaSO4 whiskers/ polypropylene were prepared by melting-extruding method. Mechanical performance of the composites was tested and surface morphology of the composites was observed by SEM. The results indicated that impact notched izod of the composites was enhanced by 49.5% compared with pure polypropylene when 10.0% Ultrafine CaSO4 whiskers were added into polypropylene and toughening effect was very remarkable. Dispersion behaviour and interface phenomenon of Ultrafine CaSO4 whiskers in polypropylene matrix were investigated by SEM. The results indicated that Dispersion performance of Ultrafine CaSO4 whiskers modified by titanate NDZ-401 in polypropylene matrix is good, which improved mechanical performance of composites to some extent.

Jan 1, 2014

By N. Acarkan

Slags usually contain some quantity of valuable metals. They are actually a secondary resource of metals, rather than an end-waste and have been utilized as a resource material in many areas. In addition, for some applications, slags have comparable or even better properties than their competitors. Leaching is a method for extraction of metals from copper slags. The extraction of metals such as copper and cobalt from the copper slag of Küre-Turkey, was investigated in the past decades. Fayalitic type of these copper slags containing 0.934 % Cu, 0.353 % Co and 50.91% Fe were subjected to the experimental study. As a result of mineralogical analysis of the slag sample, fayalitic type of slag was found to contain hercynite, magnetite, hematite, pyrite, chalcopyrite, covellite, bornite and metallic copper. Direct acid leaching methods were applied on the sample. Effects of leaching time, temperature and acid concentration on Cu and Co leaching recoveries were investigated in the direct acid leaching. The optimum leaching conditions were found as leaching time of 2 hours, solid/liquid ratio of 1/3, H2SO4 concentration of 125 g/L and temperature of 70 °C. At these conditions, 75.5 % of Cu, 95.6 % of Co and 70.9 % Fe were extracted. In the second stage of the leaching experiments, copper in the pregnant solution was precipitated by cementation to produce a Cu concentrate assaying 95.58 % Cu; cobalt was obtained by precipitation with H2S to produce a concentrate containing 62.10 % Co. As a result of this study a process flow sheet has been developed for recovering Cu and Co from these slags to demonstrate its economic and technological benefits.

Jan 1, 2014

By C. R. Mambote

Vanadium is an important metal that is used mainly in ferrous and non-ferrous alloys due to the high tensile strength, hardness, fatigue resistance and corrosion resistance. Vanadium consumption in the steel industry represents about 85% of the vanadium-bearing products produced worldwide. The primary sources of the metal are patronite, roscoelite, and mottramite. Vanadium has also been produced as a by-product of the uranium production program which uses carnotite ores as a source of uranium. Vanadiferous magnetite iron ores are used for producing vanadium as well. In addition, it is known that vanadium can be recovered from the ashes of crude oil and petroleum coke. The process for treating boiler residues, fly ash and petroleum coke is similar to the process used to treat spent catalysts and ores. However, some of these materials may contain high carbon that must be removed at specific stage of the operation. Several processes are available for obtaining vanadium from fly ash, such as roasting vanadium bearing materials in the presence of sodium salt. The salt roasted calcine is subsequently leached with an alkaline or acidic solution. To obtain a cal-cine from which the vanadium can subsequently be recovered, the carbon in the source materials has to be eliminated prior to the roasting process. Other processes use the conventional hydrometallurgical route, in which fly ash is leached with sulphuric acid to obtain an impure vanadium pentoxide. The impure vanadium pentoxide is then treated with a sodium carbonate solution under atmospheric conditions to subsequently precipitate vanadium as ammonium metavanadate. Actually, the salt roasting process is the only process used commercially. In the present study, the progress in the technology of vanadium extraction from secondary materials is reviewed. The perspectives and the challenges for new process development are discussed.

Jan 1, 2014

By W. Z. Zu

In proved reserves of vanadium-containing titanomagnetite in Panxi, China, iron grades of ores were 50% ~ 15%. China?s metallurgical industry departments defined the iron ores containing 50% ~ 20% TFe as exploitable resources and the extreme lean iron ores containing 20% ~ 15% TFe as temporary unexploitable resources, the extreme lean ores were as waste rejected into waste dump in mining process. This paper researched process mineralogy of the extreme lean ores, adopted mineral processing technology responded to the properties of the ores to treat the ores and obtained quality vanadium-iron concentrate, titanium concentrate and sulfur concentrate, therefore successfully utilized the extreme lean ores, changed the ores from waste resources to exploitable resources.

Jan 1, 2014

By A. Vilinska

Microorganisms have a tremendous influence on their environment through the transfer of energy, charge, and materials across a complex biotic mineral-solution interface. Recent developments in biotechnology have not only aided hydrometallurgical leaching operations but also shown great promise in mineral beneficiation processes. The adhesion of bacteria on minerals alters the surface properties relevant to flotation and flocculation of minerals. The biomodification of mineral surfaces occurs through the attachment of microbial cells, oxidation reactions and adsorption or chemical reaction with the metabolite products. Several types of heterotrophic and chemolithotrophic bacteria have been successfully applied in flotation and flocculation processes for the last two decades. Al-though the potential of microorganisms in minerals beneficiation has been realised by several re-searchers from their laboratory investigations, the studies were mostly confined to pure mineral systems and there is hardly any sincere effort to apply the methodologies on ores. This paper presents a brief summary of the literature in bioflotation and bioflocculation, and attempts to outline new dimensions of research for a practicable application of this technology in mineral industry.

Jan 1, 2014

By S. Jagdish

India ranks fourth in the world of iron ore production and exported 55% of the total iron ore production of 180.9 million tons in 2006-07. As per United Nations Framework Classification (UNFC), the total iron ore reserves in India is 25249 mt. This consists of about 14630 mt of Hematite ore and 10619 mt of Magnetite ore. While the deposits of magnetite iron ore are limited to the states of Karnataka, Andhra Pradesh and Tamil Nadu, hematite ore is available in abundance in Jharkhand, Orissa, Chhattisgarh, Karnataka and Goa. National Steel Policy, declared by government of India in 2005 envisages 110 million tons of steel production by 2020. This is likely to be revised upwards. Massive exploration work in iron ore is needed to convert the available resources of iron ore into reserve category. Steel Authority of India Limited (SAIL) produced more than 24.5 million tons of iron ore during 2006-07 and plans to produce 42.0 million tons per year by the year 2010-11 to meet the requirement for a hot metal production of 26.2 million tons. While processing iron ore, the challenge faced would be the reduction of the gangue materials ? alumina and silica. It is proposed to bring down alumina and silica in the iron ore to less than 2% each from the current level of 2.5%~3.5% each. Appropriate beneficiation schemes are being developed depending upon the mineralogical characteristics of iron ores at different mines in the country. The state-of-art beneficiation technologies like Hydro-cyclone, jigging, magnetic separation etc. will be incorporated. SAIL?s corporate plan envisages blast furnace burden of 15% iron ore lumps, 15% pellets and 70% sinter by 2010. This strategy opens up the opportunity of utilization of micro fines generated in the mining and beneficiation processes for pellet making. This also directs towards all together new technological approach to the beneficiation process. SAIL is planning to set-up three pelletisation plants of 2~3 mtpa capacity. Environmental issues like reduction in slime loss and utilization of dumped low-grade iron ore are very important. R&D Centre for Iron and Steel, SAIL has carried out extensive laboratory investigations in the above area. This will help in reducing the loss of valuable iron through slimes and also increase the iron ore resource base. Laboratory investigations indicate that low grade dumped ore fines with Fe: 55.5% can be upgraded to a product with Fe: 66.2% with about 48% recovery.

Jan 1, 2014

By Olli Haavisto, Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

Raman analysis is a well-established method for finding the abundant minerals in an ore sample. In this study, Raman spectroscopy is tested as a method for rapid and contactless on-line mineral analysis. Rapidness might enable on-site analysis of rock drillcore, which in turn would lead to more cost-efficient solutions in mineral exploration. This paper discusses the use of Raman analysis to identify minerals and to measure their concentration. The sample set under study consists of rock drillcore collected from Agnico-Eagle Kittilä Mine, Finland. Selected parts of the sample set are measured by Raman spectroscopy and the minerals are identified using reference spectra from a public source. Moreover, the direct measurement of concentration of different minerals with the help of Non-negative least squares (NNLS) optimisation algorithm is considered. The optimisation algorithm was constructed to form a linear combination of reference spectra which best represent the measured spectrum, or an average of measured spectra, from an ore sample. The results show that NNLS can identify abundant minerals in a given sample. Also through this method of analysis the results of a traditional point-count method can be expanded: It was observed that, due to grain size, multiple minerals consistently appear in the spectra measured over an area, which means that point-count method is not a proper way to interpret the spectra. This can be seen as a new result, as formerly the discussion has attended to other methods.

Jan 1, 2014