Search Documents

By Ph. D. Favreau, Favreau Patrice B. Eng, R. F.

Geology is important in mining by helping to identify the rocks which contain sufficient valuable ore to justify their excavation. Geologists give a geological name to each rock type, so geology is a player in blasting; when a blaster has successfully blasted rock of a given geological name at a former site, and he later has to blast rock at another site whose rock has the same geological name, then his first trial often is the same method as he used at the former site, since the geological name of the rock is the same

Jan 1, 2019

By Gabe McClain, Thomas Pallua, Joe Schrank, William C. Gates

Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds

Feb 1, 2020

By William Adamson

Precise and data driven methods of predicting and modelling blast induced vibration intensity are created and applied under field conditions on a routine basis today. These models are fed with controlled field measurements of vibration pulses generated by controlled charges under known geometric conditions. With such models blasting and geomechanical engineers can estimate vibration intensity at established critical points in mine bench geometry (surface mining) as well as within semi-permanent crown and rib pillars (in underground mining).Damage to bench walls and destabilization of large-scale geomechanical structures can be partially attributed to high intensity blast induced stresses on the rock mass and structures that define important features such as safety catch berms and haul roads. In the underground environment, weakening of critical pillars in block caving or Long Hole Open Stoping(LHOS) operations may lead to ore sterilisation. Blast vibration intensity can be linked with physical alteration in critical rock mass volumes within themine. Often the potential for vibration damage is estimated by the calculation of a critical value of vibration intensity, derived from a consideration of laboratory measured rock matrix properties. Efforts to confirm the accuracy of these estimates of critical vibration level include post blast excavation photography as well as the visual examination of rock mass, pre-and post-blast, using video camera observation of the walls of purpose drilled observation holes. These methods clearly indicate a change in fracture state due to the blast induced vibration, however further modelling of geomechanical stability will benefit if seismic measurement data can be interpreted in terms of geomechanically relevant strength parameters. This paper describes some of the results of previously unpublished research studies conducted in underground operations in Chile and Australia, where cross-hole seismic measurement profiles were interpreted in terms of dynamic modulus. This work dates from a period between 1987 and 1990 and the Author suggests that 30 years on, applying modern day technology, instrumentation and modelling methods, more meaningful, practical and applicable results may be obtained.

By Dr. Paul Worsey, Dr. Calvin Konya, Dr. Anthony Konya

Development of methods to calculate presplit blasthole pressures through simplified models, namely the Empirical Model and the Detonation Pressure Model. These models can be used with variations in explosive type and diameter, along with borehole diameter. All models have been validated with test data and shown to have minimal error.

Feb 1, 2020

By Travis A. Davidsavor, David A. Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines.

Feb 1, 2020

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In this paper, differences between the industry-standard Holmberg-Persson (H-P) approach and a semi-analytical vibration prediction model called full-field solution (FFS) are analized. The analysis is conducted at two levels: vibrations and rock damage.

Feb 1, 2020

By Matthew Clay, Colin Chambers, Susan Hookham

Opencast (quarries) and underground mines around the world use blasting methods to mine valuable ore. Traditional blasting systems use technologies such as electric delay detonator systems (developed in the 1950s) and non-electric detonator systems (developed in the 1970s) to initiate a detonation train to blast rock more effectively, and so retrieve valuable product more efficiently. However, the lack of precise control over blast timings with these approaches can result in undesirable outcomes such as significant flyrock, excessive ground vibration, uneven grade of rock and misfires (in which sections of the blast can remain unfired). The development of Electronic Initiation Systems (EIS), first used in the 1990s, introduced a higher level of control over the blast. These systems greatly reduce the negative issues associated with blasting. However, this precision introduces complexity, and with this complexity comes difficulty in demonstrating the predictability, safety and reliability of such systems.

Jan 1, 2017

By Travis Davidsavor, David Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines. Existing pipeline company standards would have effectively precluded the construction of the replacement pipe by blasting rock. To facilitate the required construction and evaluate actual pipe stress during blasting to ensure pipeline integrity, a comprehensive evaluation methodology was developed by a team of pipeline, mechanical, geotechnical, instrumentation, and blasting engineers. A total of 60 strain gages were affixed to the steel pipe and seismographs were buried at the surface near the blasting area. Test blasting allowed pipe stresses with corresponding ground motion to be monitored. A conservative analysis approach evaluated individual peak strains and revealed that only small pipeline strains, and therefore stresses, were induced in the pipeline as a result of blasting. This evaluation allowed specific procedures to be developed to inform the blasting operation of maximum explosive loading and minimum charge distances. Additionally, this effort provided the pipeline operator with appropriate pipeline operating pressures during blasting activities to limit total stresses in the pipeline to be below allowable stresses imposed by code, regulators, and company operational limitations. Recommendations were developed to measure the blast generated ground vibrations with seismographs buried at the depth of the pipe, near the pipe, and limit the ground vibrations from blasting to 150 mm/s (6 in/s). If ground vibration intensities of 120 mm/s (4 in/s) or more were observed, additional engineering review is recommended. Finally, all blasting would be suspended and all activities reviewed at peak ground vibration intensities of 230 mm/s (9 in/s). The evaluation effort resulted in effective and efficient construction of the pipeline replacement and allowed the pipeline operator to better understand blasting induced stresses on their assets.

By Norman Paley

A blasting project was undertaken at the Teck Alaska Red Dog Mine in 2005 to 2007 to determine the extent that using electronic detonators could increase Semi-Autogenous Grinding (SAG) mill throughput. The results of that project were reported at the 2010 ISEE Annual Conference. This paper is a postscript to that project and provides the fragmentation resulting from the implementation of a 15% pattern expansion using electronic detonators.

Jan 1, 2012

By L C. Taylor

Both the U. S. Navy and the U. S. Army are interested in knowing more about the loading applied to vehicles which are unfortunate enough to encounter a detonation of a buried mine in the course of performing their normal duties. The Dynamic Effects Laboratory at the University of Maryland has been involved in small scale testing for ten years to assist the Navy and the Army in understanding the loads that are applied to personnel carriers when a buried explosive detonates beneath them. This paper describes results from small scale tests conducted to determine the loading mechanisms on target plates when subjected to loading due to the detonation of a buried mine in saturated sand, dry sand, and water. Transparent target plates were utilized in order to determine the loading process beneath a floor board on armored vehicles. Various charge sizes were scaled in the laboratory accordingly to a standardized full size threat encountered in the battlefield. Tests were conducted in saturated sand, dry sand, and water keeping the stand-off distance of the target and the depth of burial of the charge constant. In the case of water impacting a transparent PMMA plate the crack propagation was recorded and the crack velocity is determined. Additional tests were performed in saturated sand by varying the stand-off distance of the target but keeping the depth of burial of the charge constant. The small-scale test results could be scaled to full scale by using verified scaling laws.

Jan 1, 2016

By Thomas C. Rube, T S. Bajpayee

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs.

Jan 1, 1996

By Manuel Gutierrez, Roberto Gomez, Juan Aravena, Johan Gjoevad

The use of explosives in mining operations is a process that involves the search for an ideal explosive for the type of geological condition of the mineral to be extracted. For the explosives present on the market the majority are based on Ammonium Nitrate. This as it is an ideal balance of high energy efficiency achieved with low development of gas emission. The manufacturing and loading operation of the explosive requires multiple process stages and different raw materials, which, if is not correctly supervised and controlled may cause the development of harmful gases or, in the worst case, even toxic gases. The majority of mining operations are located at remote locations without the presence of communities, and hence individuals, which could be affected by emission of the harmful or even toxic gases. In these operations the protection is mainly to protect the employees of the operation. However, if the operation is located near communities, the effect of these gases becomes a serious problem. The communities' perception of post-blasting gases, according to interviews carried out in this project, describes these as smells of black gunpowder, damp soil with a volatile permanence and medium intensity, sometimes a stinking tone is added. The legislation in Chile that controls the exposure of “workers” to different gases is Supreme Decree 594, 2019 (Decreto Supremo 594). Currently the Chilean Ministry of Environment and Sernageomin (Servicio Nacional de Geología y Minería) are taking actions to reform and strengthen oversight, seeking through a short law to provide more tools to the government to decentralize decisions in case of non-compliance with the decree. This paper describes the development and implementation of a permanent and remote gas monitoring system, considering the reasons for choosing the gases to be included in the equipment, the types of sensors and their capabilities, the way to verify in the field the correct functioning of the technology throughout the project, and finally how the data collected in the field is meeting the government's expectations in terms of permanent and online reportability. Additionally, it addresses the continuity of gas monitoring in the community that will disappear in the short term due to the expansion of mining operations, thereby ensuring the protection of both workers and affected communities.

Jan 21, 2025

By Tom Snyder, John Brulia

Part I is the first of a series of articles by the authors on hazardous materials (HM) transportation safety and compliance for shippers and carriers who offer and transport commercial explosives in commerce on public highways in the U.S.

Jan 1, 2014

By S. Mansfield, A. Sharma

At a large open cut copper mine, in pit crushing and conveying is used to shorten haul routes and minimise stockpiling of ore. This strategy decreases capital expenditure by reducing the number of haul trucks and excavators required and reduces the need to rehandle ore from stockpiles with a secondary load and haul fleet, with an overall goal of lowering operating costs and carbon emissions. As the mine has developed and expanded, it was necessary to extend the conveying network and install a fourth, semi-mobile crusher to increase the output of the operation, while maintaining the operational efficiencies. This required the blasting of a new tipping bench and pocket for the installation of one of the largest and most powerful semi-mobile, crushing plants. Fed by 360 tonne (396 ton) ultra-heavy class haul trucks, the KB 63-130 Pro gyratory crusher is the highest capacity available in the market. This paper describes the holistic process that was applied to model, design and execute the blasts required to create the pocket for the semi-mobile crusher, the surrounding tipping bench, plus the conveyor corridor and access ramp used by the ultra-heavy class trucks.

Jan 1, 2024

By Clarence Hall, Charles E. Monroe

Squibs, Fuse, and Detonators It has been made clear in the discussion of combustion and explosion and the description of various explosives that they can be caused to explode by various means. All of them can, under some circumstances, be made to explode by fire. Some of them can be caused to undergo a detonating explosion by setting off a detonator in contact with them. In blasting use is made of both these means for setting off explosives, the means used being determined by circumstances.

Jan 1, 2010

By M Dandeneau, P I. Rajic, K D. Murphy, M B. Johnson, T J. Tope

"Manufacturers and users of energetic material [i.e., propellants, explosives, pyrotechnics (PEP)] generate unserviceable, obsolete, off-specification, and damaged items that are characterized as reactive waste. These items must be safely treated and disposed of or reclaimed/recycled, thereby controlling existing waste inventories at manageable levels. The most commonly used disposal and treatment method, particularly at U.S. Department of Defense (DoD) installations, is open burning/open detonation (OB/OD). However, regulatory constraints and the inability of operators toobtain permits required for treating these waste has led to the recent reductions and limited use of OB/OD treatment at many installations."

Jan 1, 1995

By R. K. Wharton

A European Directive requires that an explosive which is sold or transported within Europe must meet certain essential safety requirements from 1 January 2003. The assessment and certification of such an explosive is undertaken by an Explosives Notified Body and if the explosive meets the requirements a certificate is issued that allows the affixation of a CE mark. The presence of a CE mark ensures the product free access to European markets. The paper examines the requirements of the Directive, identifies those explosives that come within its scope, considers the role of an Explosives Notified Body, and explains the process of applying for certification.

Jan 1, 2002

By Robert Martin, Brian W. Stump

As part of a series of seismic experiments designed to improve the understanding of the impact of mining blasts on verifying a Comprehensive Test Ban Treaty, a sixteen station network of three-component seismic sensors were deployed around a large cast shot in the Black Thunder Mine. The seismic stations were placed, where possible, at a range of 2.5 kilometers with a constant inter-station spacing of 22.5 degrees. All of the data were recorded with the seismometers oriented such that the radial component pointed to the middle point of the approximately 2 kilometer long shot. High quality data were recorded at each station. Data were scaled to a range of 2.5 kilometers and the sum of the absolute value of the vertical, radial, and transverse channels computed. These observations were used to construct radiation patterns of the seismic energy propagating from the cast shot. It is obvious that cast shots do not radiate seismic energy isotropically. Most of the vertical motion occurs behind the highwall while radial and transverse components of motion are enhanced in directions parallel to the highwall.

Jan 1, 1997

By Paul Downing

When was the last time the documents and paperwork were cleaned out of the glove boxes, door pockets, under the seats and above the visors in your company vehicles? Insurance cards that expired three years ago and vehicle registrations from 1999 through 2003, for instance, don’t do any good and just take up space

Jan 1, 2008

By Dale Preece, Joergen Pilz, Zavis Zavodni

An overland conveyor was constructed at a surface coal mine to reduce the truck haul distance and make the operation more efficient. An important element in this system is a truck dump facility to transfer coal from truck to conveyor. Mechanically stabilized earth retaining walls were employed to accommodate the coal processing equipment, including the crusher, in this facility. These retaining walls are close enough to the pits being mined that blasting induced vibrations must be considered in analyses of the wall structural stability.

Jan 1, 2010