Search Documents

By Valeri Mitkov

Studena Quarry is one of the main suppliers of inert materials for concretes production in Sofia. It is characterized by massif heterogeneity in density and fissuration. Failure to take into consideration this fact during the planning of the blasting works recently had unsatisfying results in their carrying out – obtaining of materials with too small dimensions or high percentage of outsize material. Series of test blasting were carried out to find the relations for calculation of the main parameters of the drilling and blasting works. The blasting network was enlarged to 6 x 6 m, the diameter of the shot-boreholes was changed from 110 to 152 mm, the stem of the boreholes was significantly reduced and the relative consumption of blasting agents as a whole was reduced to 0,37 ?g/m3.

Jan 1, 2010

By Adam Stremcha, John MacGregor

Initial planning called for 3 separate drop shafts and 3 separate vent shafts to be pulled back from the excavated tunnel with a large diameter raise bore machine. With time constraints and the raise bore machine already in high demand on other shafts, a more “traditional” drill and blast approach was taken on a few of the larger drop shafts. This decision proved to be not only cost effective, but also reduced schedule impact as the shafts were excavated simultaneously with the other raise bores.

Jan 1, 2010

By Denard Brandt, Isidro Martinez, Greg Baker, Laura Slattery, Teddy French

The Dos Pobres Mine is a copper oxide heap-leach mine located near Safford, Arizona. Mine production is 180,000 tons (163,293 tonnes) per day with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority.

Jan 1, 2010

By S. S. Bud Jenkins

I went to an underground limestone mine recently to demonstrate the use of borehole liners. The liners were for horizontal holes in a normal “V” cut tunnel round. I hadn’t been in this mine for about 40 years. What a change. Way back they used cap and fuse and lit each fuse individually with a blowtorch. The face was about 40 feet wide and 14 to 16 feet high. They used ladders to get to the upper holes. The rounds were mostly slab rounds. I never saw this happen but had heard several times that the first holes were going off before the last holes were lit. I guess if this was true the use of slab rounds was a plus for safety. As far as I know they never had an accident but it was a scary procedure. There were a lot of scary procedures in the past and thankfully things have changed.

Jan 1, 2010

By C. Adcock, R. Farnfield, G. Adderley

The use of explosives to create special effects in the film industry is a well-known past time. A recent production required simulation of a large scale water splash from the effect of a statue falling from a cliff edge and impacting on an open body of water. This was to be achieved through the use of precisely delayed explosions detonated near the surface of the water. A survey of the area revealed a breeding farm for sea bass approximately 250 metres (273 yards) from the intended blast area. It was initially thought that the water pressures produced for the detonation of the explosives may cause harm to the fish. Much work has been carried out over the past few decades on the effect of open water blasting and its effects on aquatic wildlife; this includes water pressure modelling techniques which can be used as predictive tools.

Jan 1, 2010

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010

By P D. Katsabanis

The dynamic tensile strength of geomaterials is known to be highly dependent on the strain rate of the load applied. This is significant in applications where the material is subjected to shock waves and impact loading. This paper proposes the use of a simplified method to determine the dynamic tensile strength of hard brittle rocks using an explosively impacted version of the Hopkinson Pressure Bar. A compressive stress wave was propagated in a sample, representative of the material of interest, by detonating a small charge at one end of a cylindrical sample. The tension wave, generated upon reflection at the free face, causes spalling in brittle materials. Strains at four points in the specimen were continuously measured and the dynamic tensile strength was determined by applying the one-dimensional wave theory.

Jan 1, 2010

By Ye Yuan, Jaak Daemen, Shaguo Yuan

ABSTRACT: A 400m2 (480 yd2) heavily reinforced high-strength concrete slab 800mm (31 inch) thick had to be demolished. Underneath it was a 300mm (12 inch) thick underlying structure consisting of three layers: a cushion coat, a water barrier and a concrete layer that protected the water barrier. It was strongly desired by the owner that the underlying structure, especially the water barrier, remain undamaged during the blasting demolition of the reinforced concrete slab above it. This paper discusses the design of the demolition blast, problems encountered, and practical solutions to these problems. First, the impact caused by the charge explosion on the remaining structure was studied. In order to limit crack propagation in the concrete to the bottom of the concrete layer, the concrete isolation layer underneath the bottom of the slab to be demolished was left in place, to protect the water barrier and its protection layer. The effects of blasting vibrations on adjacent concrete were analyzed and precautions were proposed in the design. A safe blast design meeting the requirements to protect the water barrier below the slab was detailed. Rainwater collected and stored above the remaining underlying structure remained in place for two weeks, confirming that the design and blasting were successful.

Jan 1, 2010

By Chris Breeds, Larry Leone, Jerry Wallace

Project Owners typically require General and Detailed Blast Plans when blasting close to important structures and specify the maximum allowable peak particle velocity for each potentially affected structure. Low, residential level PPV limits may be specified which significantly restricts the potential for blasting to be effectively used. Contractor’s responding to these contract conditions typically cite historic case studies which may, or may not, apply to the specific situation and/or types of structures for which limits have been set. A long submittal cycle typically follows.

Jan 1, 2010

By Diego Quezada, Carlos Munoz, Marco Arellano

It is well-know that the presence of fine materials in mining has a direct impact on the plant processes with a great influence in the total amount of ore production and recovery. In Cu mining heap leaching is affected negatively by the presence of fines material (< 100 # Ty) in leaching piles, where a decreasing in Cu recovery is achieved in a lot of cases. D&B practices used normally in mine operations can generate fines > 4% in blasted piles, but the principal effects are reflected in the downstream processes where pre-conditioning post-blast materials release greater quantities of fines.

Jan 1, 2010

By Seokbin Lim

In the design of explosives devices, an understanding of the behavior of explosively propelled matter is one of the most important steps in maximize the performance of these devices. For instance, an explosively driven metallic liner in LSCs (Linear Shaped Charges) creates its functional effect of penetration after a finite distance of travel (before collapse), thus the detailed study of the projection mechanism of the flat liner after detonation helps in the optimization of the design of LSCs. In a typical metallic flyer driven by explosive detonation, the detonation gas propels nearby matter including flat flyers. After a certain degree of expansion in the detonation gas, the flat flyer reaches its maximum velocity and slows down afterward. These typical behaviors are well investigated and numerically studied by many researchers. However, the rarefaction intrusion (detonation gas expansion) near the surface of the explosive charge creates significant deformation of the flat flyer , and produces U-shaped bending or deformation near the edge of the flyer during projection, creating unexpected behavior in explosive devices of interest. In this paper, a preliminary investigation of a localized Ushaped deformation of flat metallic flyers during projection is studied utilizing a theoretical approach and computational modeling facilitating an understanding of a general tendency of the deformation behavior.

Jan 1, 2010

By Kwang-Yeom Kim, Dong-Gyou Kim, Hyo-Kwan Yoon

This study was intended to simulate the blasting model using notched-hole with numerical approach. Numerical analysis approach was applied to compare and evaluate the blasting model using notched-hole and circular hole. To implement non-linear dynamic blasting model, blasting analysis was carried out with AUTODYN code. Behavior of two models was compared and evaluated using AUTODYN and visual analysis and quantitative evaluation based on pressure and stress to verify the effect to induce the destruction territory to the specific direction when blasting with notched hole was attempted.

Jan 1, 2010

By Dale Preece, Joergen Pilz, Zavis Zavodni

An overland conveyor was constructed at a surface coal mine to reduce the truck haul distance and make the operation more efficient. An important element in this system is a truck dump facility to transfer coal from truck to conveyor. Mechanically stabilized earth retaining walls were employed to accommodate the coal processing equipment, including the crusher, in this facility. These retaining walls are close enough to the pits being mined that blasting induced vibrations must be considered in analyses of the wall structural stability.

Jan 1, 2010

By K. Hausmann, W. Whelchel

The properties of ethylene Ionomer resins for the inner layer of non-electric shock tubes will be discussed in detail, and opportunities for property enhancement will be pointed out. A stiffness program for prediction of shock tube stiffness, as determined by the stiffness of the individual layers, will be presented and discussed.

Jan 1, 2010

By Robert Hopler

Testing Stations Abroad At the Seventh International Congress of Applied Chemistry, Drs. Mente and Will communicated a paper on the above subject. All large coal-getting countries employ testing stations of some kind, in order to safeguard, to the highest possible extent, the lives of the men employed in this industry. Most countries employ galleries of considerable diameter, and fairly short length; but within recent times, long galleries, with drives and other accessories approaching as closely as possible the actual conditions of mining have been installed. The following are the details of the testing stations employed in the countries mentioned.

Jan 1, 2010

By Jeffrey Meissner, Mike Waldron, Charles Dowding

Most studies of crack response have focused on opening and closing of a crack in the plane of the wall in which the crack occurs. Crack movement also occurs perpendicular or normal to the plane of the wall. This paper will examine and compare the in-plane and out-of-plane (normal) response of cracks in two different residences near limestone quarries. In two locations, sensors that measure in-plane and normal displacement were installed side-by-side on the same crack, allowing direct comparison of the two modes of response. In a third location, a perpendicular pair of displacement sensors was installed in a corner of a room to observe the bidirectional response of the structure at a corner. Both long-term and dynamic data were recorded with the same sensors; temperature, humidity, and air over pressures were also recorded to compare blast and weather effects. Measurements show that ratios of out of plane to in plane response to dynamic events can vary. However, the ratios of out of plane (normal) response to vibratory events to that of climatological change is still as small as the ratio for in plane crack responses.

Jan 1, 2010

By Randall Head

The drilling at the Taum Sauk Reservoir was a unique compilation of the latest technology and everyday common sense. This site is comprised of rhyolite, which is 30 times harder than limestone in comparison. Using some of the most state of the art drills, coupled with GPS guidance, angular drilling systems, and an ordinary piece of string, some of the most amazing drilling feats were accomplished. By constructing the new dam on top of a mountain that had been blasted once before nearly 50 years ago treacherous conditions for the drills and crew were a challenge. The drills had to be flown in by cranes to get to their locations, where they then drilled anywhere from 2.5 to 6 inch (6.4 to 15.2 cm) holes at angles up to 24.4 degrees. Custom drill bits were designed by the drilling crew to tackle feats such as drilling holes up to 120 feet (36.6 m) deep. A main challenge was the shape of the reservoir, as it is not in a straight line, but rather round, so no technological way was readily available to use to drill. Common sense came in and an ordinary piece of string was used to aide in drilling the hole. A revolutionary step was that our drill was used to core our own samples. By using our own equipment, we were able to complete this task for one-third of the cost of having a third party contractor obtain the core samples. On this unmatched jobsite, it has been established that technology has come a long way, but when all else fails, a piece of string will do just fine.

Jan 1, 2010

By William Nicoll

Those who use electric detonators in firing blasts will be interested in a new electrical testing instrument known as the ‘Blasters’ Friend’, recently devised by the New York Blasting Supply Co. of New York. Owing to the necessarily delicate construction of the platinum wire bridge in the shell of a detonator, it frequently happens that it becomes broken or disconnected; thus destroying the circuit and rendering the detonator worthless. In many cases, misfires and premature explosions are caused by defective detonators. Heretofore, to detect the deficiencies of a detonator before using has been an impossibility, owing to the absence of a testing instrument adapted to the purpose.

Jan 1, 2010

By Kenneth Eltschlager

Blasting represents the highest risk of any surface coal mining activity that could result in injury and/or property damage off the permit area. In addition, blasting related issues e.g. flyrock, vibrations, air blast, etc., are responsible for a large percentage of citizen complaints. Thorough and consistent regulation of individuals certified to conduct blasting by the Office of Surface Mining Reclamation and Enforcement in Federal Program states and on Indian Lands under Federal jurisdiction is vital, as it serves to: facilitate coal production to meet the nation’s energy needs; protect people and property on and adjacent to Federal mining permits; form a basis for states to grant reciprocity certificates to Federal blasters; and be a positive example to primacy states. OSM issues Federal blaster certificates for blasting on Federal surface coal mine permits. The certification program includes experience, training and testing components similar to many of the states. But where a state program may focus on the specific blasting applications within its boundary, the OSM certificate requires a very diverse test to cover all potential blasting applications and products across the nation. Therefore, the Federal certificate is a good surface mining credential for blasters anywhere in the United States.

Jan 1, 2010

By Christoph Muller, Geoffrey Liggins, Mohan Hensman

Modern commercial blasting is as much a technical process as it is a business one. As with most processes both aspects of blasting are driven by and generate new data. The time-critical nature of commercial blasting in mining and construction projects, dictate the timely exchange of information so as not to impede production or commerce. Up-to-date information about the blast to be undertaken can help suppliers: meet customers’ expectations to address challenging ground conditions; react to a market where quickly changing orders occur regularly; and address as-drilled blast patterns as opposed to baseline plans. “Real-time” data exchange into and out of the blasting process supports the whole-of-mine data management that the industry is migrating to.

Jan 1, 2010