Search Documents

After nine years of negotiations, the U.N. Conference on the Law of the Sea approved a Law of the Sea Treaty text in April. Israel, Turkey, the United States and Venezuela voted against the text and 17 other nations including Belgium, the Netherlands, Italy, the Soviet Union, the United Kingdom and West Germany abstained. These nations still have the option of joining the treaty when it is opened for signing in December. However, the Reagan Administration has stated that several provisions of the deep seabed mining portion of the text are unacceptable and it seems unlikely that the United States, at least, will change its position. ALUMINUM Reynolds Metals Co. has criticized an Oregon state plan to relax air pollution standards for aluminum plants. The company feels that relaxation of the rules does not go far enough. Reynolds officials say that they have spent about $31 million at their Troutdale plant for state-of-the-art pollution control equipment, and if they are required to make the pollution reductions called for in the 1986 rules, Reynolds would be forced to close the 40-year-old plant.

Jan 1, 1982

By Marcel Vanpee

Eight extinguishing powders KCI, were tested on five types of diffusion flames. The effect of flame temperature on the inhibition efficiency was investigated by varying the oxygen index of the flame supporting atmosphere. Inn addition a spectrographic investigation of powder flame dissociation products was carried out on the methane/air/ABC (NH4H2PO4) flame. Dissociation products for this flame included P0, PH, NH, and Na. It is concluded that the main factor to be considered in the efficiency of tie powder is the flame temperature Purple K (KHC03) was typically inefficient in low temperature flames and very efficient in high temperature flames. On the other hand, ABC (NH4H2PO4) was found to lose its efficiency at high temperature but to be quite efficient in the low temperature flames. The effect of temperature is offered as an explanation of the poor efficiency of Purple K (KHC03), against coal dust explosions as contrasted to the high efficiency of phosphate salts against coal dust explosions.

Jan 1, 1982

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of manganese from known domestic occurrences. Eight of these deposits were found to have demonstrated resources totaling 420 million metric tons with an average grade of 10 percent contained manganese. They were found to be submarginally subeconomic. Economic evaluations of the eight deposits resulted in incentive prices ranging from $8 to almost $35 per long ton unit (22.4 pounds) of contained manganese. Comparing these prices with the current market value of $1.70 per long ton unit of manganese clearly illustrates the submarginal nature of the domestic ores analyzed. These domestic resources would probably not be developed except in the case of an extreme national emergency. Production from the eight deposits would take 3 to 6 years to develop, and the final product would be manganese ore concentrate, which could be used in the production of ferromanganese. If preproduction development began in 1981, annual production would peak in 1987 with 900,000 metric tons of recoverable manganese. Thereafter, production would see a steady decline unless additional resources were located or technologic improvements were made to allow processing of lower grade material, or unless mining and processing of ocean manganese nodules began to take place.

Jan 1, 1982

By David A. Summers

The use of high pressure fluid cavitation is investigated as a means of breaking an ore into its constituent grains. This Cavitational Rock Dissagregation (CRD) is found to be possible and effective in breaking down galena ore, both in sandstone and dolomite host material. The technique did not work as well in comminuting and cleaning oil shale, because the cavitation drove the oil into emulsion with the water. The presence of dominant bedding in the rock also caused preferential breakage to these lines, rather than to the individual grain boundaries. This problem was also encountered in tests on igneous ore where weakness plants of the overall ore proved weaker than the boundaries of the individual grains. It was found that the prevailing expression of cavitation erosion dependence on pressure was not absolutely valid. In contrast it was found that CRD is much more sensitive to jet flow diameter, and when this was recognized it was found possible to erode rock with compressive strength of up to 350 MPa with operating jet pressures of 10 MPa.

Jan 1, 1982

By J. C. Franklin

An experiment was conducted by the U.S. Bureau of Mines and the Canada Centre for Mineral and Energy Technology (CANMET) to measure the emanation rate of radon from cemented unclassified mill tailings in two dewatered stopes of a uranium mine at Elliot Lake, Ontario, Canada. The radon was monitored upstream and downstream and in both stopes to determine the concentration in the stopes and the amount exhausted from both stopes. The emanation rate was determined to be 0.55 pCi/cm2 sec-1 from the mill tailings, which is approximately 1,000 times higher than the average flux in the mine before backfilling.

Jan 1, 1982

By Jack C. White

As part of an investigation of the production of alumina by the nitric acid leaching of kaolinitic clay, the Bureau of Mines designed, built, and tested a fluidized-bed system for the calcination of aluminum nitrate nonahydrate to alumina, while recovering nitric acid. The calciner consisted of an 8-in-square by 36-in-tall vessel containing 18 in of fluidized solids. Molten aluminum nitrate, sprayed directly into the fluidized solids, formed sandy, granular alumina by growth of successive layers on fluidized particles. Solids were fluidized in a dense bed at temperatures of 250° to 500° C with steam, air, or mixtures thereof. Decomposition of nitrate ranged from 4 to 10 pet during single-pass steam or air fluidization, respectively. Alumina dust losses and low throughput are significant unsolved problem areas.

Jan 1, 1982

By H. C. Ko

Heats of solution of calcium carbon-ate (calcite) and calcium oxide in hydrochloric acid were determined by solution calorimetry. Combination of these two heats yields a value of 42.643±0.024 kcal/mole for the enthalpy of calcination of calcite at 298.15 K. Literature data on ?H°298.15 of calcination of calcite were reviewed and compared. Thermodynamic properties for the calcination process were calculated from 298.15 to 1,500 K using Gibbs energy functions. This research was undertaken by the Bureau of Mines as an effort to provide thermodynamic data for the advancement of minerals technology, energy conservation, and environmental preservation.

Jan 1, 1982

By E. A. Johnson

The Bureau of Mines determined the effect of slag additives on copper solubility and the distribution of typical impurity elements between copper-iron matte and silica-saturated fayalite (iron silicate) slag at 1,250° C, in CO-C02 atmospheres with 10 pct S02. Small additions (<10 pct) of CaO, A1203, and MgO were shown to decrease copper solubility in the slag. Additions of CaO increased the solubility of bismuth and tellurium in the slag at lower matte grades. Al 20 3 additions decreased the solubility of tellurium in the slag, but increased that of bismuth at lower matte grades. A1203 additions increased the solubility of both at lower matte grades. With no additives, matte grade did not affect the solubility of bismuth in slags, whereas increasing matte grade resulted in a slight decrease in the tellurium solubility in slag. Additions of CaO or As203 alone to the slag increased selenium and arsenic distribution to the matte, but had little or no effect on antimony distribution; whereas small MgO additions decreased antimony distribution to the matte but had no effect on arsenic and selenium distribution. In slags with no additives, selenium distribution to the matte increased with increasing matte grade, while that of antimony decreased and that of arsenic was unchanged.

Jan 1, 1982

By Larry Joe Linley

The Department of the Interior, Bureau of Mines is reviewing explosion protection methods for use in gassy coal mines. This performance criteria guideline is an evaluation of three explosion protection methods of machines electrically powered with voltages up to 15 000 volts AC. A sufficient amount of basic research has been accomplished to verify that the explosion-proof and pressurized enclosure methods can provide adequate explosion protection with the present state of the art up to 15 000 volts AC. The routine application of the potted enclosure as a stand alone protection method requires further investigation or development in order to clarify performance criteria and verification-certification requirements. An extensive literature search, a series of high voltage tests, and a design evaluation of the three explosion protection methods performed at White Sands Test Facility indicates that the explosion-proof, pressurized, and potted enclosures can all be used to enclose up to 15 000 volts AC, if the performance criteria and verification-certification requirements recommended in this guideline are implemented.

Jan 1, 1982

By C. W. Morris

This Final Report describes the major technical activities that were accomplished to produce a comprehensive continuous miner training system (CMTS) for coal industry utilization. The primary product of this program was a continuous miner part-task trainer. It is composed of an interactive computer graphics system combined with the operating controls of a continuous mining machine mounted in a simulated cab. The cab contains an audio system for reproducing continuous miner operational sounds. The trainer is supplemented with a complete set of cognitive materials that provide instruction in the operation, safety and health of continuous miner operations. A complete summary of the field test and evaluation of the CMTS is provided along with a set of recommendations for further training program refinements, expansions, and utilization.

Jan 1, 1982

Continuous remote sensing of methane concentration in underground mines. Approach A methane transducer, developed as a fixed point rib-or face-mounted operating device, measures ambient levels of methane and produces a signal that is proportional to the measured concentration. How It Works The methane transducer, developed under contract for the Bureau of Mines, uses a catalytic-type sensor which will detect methane concentration. The transducer is mounted vertically, as shown. This type of mounting minimizes dust accumulation on the sensing element, which might cause degraded operation. The unit must not be located in an area where water can continuously drip or run on It. The transducer generates an electrical signal proportional to methane concentration at the sensor. A sensor failure output indicates the status of the sensing element A circuit within the methane transducer detects whether the sensing element is shorted or open. A high signal (approximately 8 Vdc) on the failure output Indicates the sensor element is operating In Its normal range. A low output (less than 1 Vdc) indicates an element fault. The methane transducer, enclosed in a stainless steel

Jan 1, 1982

By Walter E. Pittman

In its role of providing technical assistance to the mining industry, the Bureau of Mines&apos; Tuscaloosa Research Center has conducted research to develop trapped miner location systems which would aid in locating miners trapped by underground mining disasters. Efforts to produce electromagnetic systems for the location of trapped miners underground and to communicate with them were surveyed, from the 1920&apos;s to 1981. Theoretical studies of through-the-earth electromagnetic transmissions are described as well as studies of the electrical characteristics of various rocks, minerals, and soil. Several trapped miner location systems are reviewed including the Westinghouse systems, the DEVELCO system, and an automated three-dimensional location system, and the phase difference of arrival technique. Tangential research, relevant to trapped miner location systems is described. A comprehensive bibliography covering all aspects of trapped miner, through-the-earth electromagnetic location and communications systems is appended.

Jan 1, 1982

By Charles T. Chislaghi

An economical, remotely operated (automated), temporary roof support (ATRS) has been developed by the Bureau of Mines for use on a single, fixed-head roof-bolting machine (squirmer) that operates in low coal seams (less than 42 in thick). The ATRS eliminates the need for squirmer operators and helpers to go under unsupported roof to set or remove temporary support prior to or during the roof-bolting cycle--a task that annually accounts for approximately 20 pct of all roof fall fatalities. The ATRS can be adapted to any squirmer used in the U.S. low coal fields. A prototype ATRS was field-tested at Imperial Colliery Co.?s Mine No. 20 in Eskdale, W. Va. The Mine No. 20 amended roof- control plan, which requires the use of the Bureau?s ATRS as temporary support during face bolting, has been approved by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor.

Jan 1, 1982

By Donald O. Capstick

The local geology, the lack of recorded mining activity, and our field investigation and associated sampling indicate a low potential for mineral resources. Claim records and the literature review failed to show any lode or heavy mineral placer mining claim locations that are definitely in the area or anomalous mineral concentrations in the study area. Field investigations revealed no claims, prospects, or mineralized areas.

Jan 1, 1982

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract HO 395132 to develop improved sensor cells for use in direct-reading detectors and diffusion exposure meters. A pumped CO sensor cell was developed which has a shorter response time, improved temperature cycle characteristics, and improved linearity and stability at high CO concentrations. Diffusion CO sensor cells have shown good response level stability and linearity up to 1000 ppm. In addition, a new sensor cell catalyst has been developed for NO2 sensor cells which has a much shorter response time and improved response stability characteristics.

Jan 1, 1982

To cost-effectively reduce noise and vibration in newly manufactured mantrip vehicles. Approach Previous Bureau of Mines research demonstrated that noise controls could be in-stalled on existing mantrip vehicles, thereby substantially lowering noise levels inside the mantrip. Under Bureau sponsorship, a manufacturer of mantrip vehicles agreed to incorporate similar noise controls into a new vehicle during manufacture. Throughout this project, durability, maintainability, and cost were considered to be as important as noise reduction. How It Works The following noise-control features were included in the new mantrip: (a) Suspension Isolation- The suspension components were isolated by inserting elastomeric materials between them and the vehicle frame.

Jan 1, 1982

To suppress the natural bacterial action in acid mine drainage (AMD), the major contributor to acid formation. Approach Recycle partially-treated affluent back to the source of AMD within a mine, or to the coal or coal-waste stockpile. This effectively eliminates any further biologically-promoted AMD by inhibiting catalyzed weathering or oxidation by acid-forming bacteria. How it Works AMO-type effluents can be largely reduced by "recycling" the acidic outflow back to the source of AMD within a mine or to the Input side of a waste pile to percolate through the reactive pyrite and bacteria mixture. The bacteria in the cell thrive on the oxidation of ferrous to ferric iron through the electron transfer, Fe2 +[=]Fe3 + + e. Its reaction product [s, therefore, essentially ferric iron. While small quantities of Fe3 + will not interfere with the exponential multiplication of the bacteria

Jan 1, 1982

Estimate costs for projected uranium in-situ mining operations. Approach Develop a computer model and an associated data base which will allow users to supply data applicable to a specific mining site in order to estimate total capital and operating costs for a potential in-situ mining operation at the site. How the Model Works The model requires a minimal amount of input from the user. The data input must be known or estimated information about a potential in-situ mining operation. The user can also supply any additional project specifications. The computer model uses a process-engineering approach and determines through a discounted cash flow analysis the total capital and operating costs for the life of the project. This time-span measures from the start of the pilot-scale operation through to the site&apos;s restoration and reclamation. The model will determine the production cost per pound of material mined subject to the rate of return identified by the user. Conversely, it will also solve for the rate of return realized for the specific sales price per pound. [ ] Currently the model&apos;s data base can tai ns costs, rates, and specifications for Texas and Wyoming, the only states where commercial uranium in-situ mining is being conducted. However, this model can be used by anyone who is conducting in-situ leaching or who plans to leach uranium in-situ. At least part of any uranium deposit has a potential for in-situ mining.

Jan 1, 1982

By T. E. Ackman

The Bureau of Mines conducted a study of current trends in methods employed by the coal industry to dispose of acid mine drainage (AMD) treatment sludge. Thirty-three AMD treatment plants, operated by 11 Pennsylvania coal companies, were randomly surveyed. These plants provided data for calculating sludge volumes, as well as information on sludge settling, transportation, and disposal. Onsite visits allowed observation of problems associated with the various methods of sludge disposal: (1) disposal into a deep mine, (2) permanent retention in ponds, (3) disposal at an active coal refuse area, and (4) onsite burial. Method 1 is the most frequently used and the most environmentally sound. It is apparent, based on this representative sampling of AMD treatment plants, that the magnitude of sludge production is such that an aggressive and directed effort in reduction of sludge volume is seriously needed. The areas of major concern are (1) the amount of surface land required for sludge storage and disposal, (2) reclamation of these disturbed surface areas, and (3) effective and efficient means of removing, transporting, and disposing of AMD sludge. In this report, an engineering approach to the practical problems associated with the existing disposal methods is presented, together with recommendations for future research.

Jan 1, 1982

By John L. Schaller

The Bureau of Mines, U.S. Department of the Interior, has investigated the extraction of alumina from domestic kaolin clay by leaching with boiling 26 wt-pct hydrochloric acid. Acid leaching of crushed calcined kaolin feed yields slurries that are slow settling and difficult to filter because of the presence of fine particles generated in crushing, calcining, and leaching. Laboratory research showed that tumbling and moistening crushed raw kaolin on a pelletizing disk caused the fines to agglomerate on the surfaces of the larger particles, while the sharp edges and corners of the larger particles were rounded off. Minus 16-mesh crushed raw kaolin was misted on a 36-in-diam, 8-in-deep pelletizing disk at rates of 175 to 250 lb/hr, and was calcined in either a rotary or a fluidized-bed calciner; negligible degradation occurred. The physical properties of the misted calcined kaolin were evaluated in the leaching system of the clay-hydrochloric acid miniplant. Only minor attrition occurred during leaching, and the slurry was readily filtered on a continuous belt filter.

Jan 1, 1982