Search Documents

By Howard B. Hamilton

A switching system for high fault current 300 and 600 volt DC trolley and haulage systems, as used in the mining industry is presented. The system consists of paralleled main and auxiliary contactor circuits with a liquid metal current limiting device (CLD) in series with the auxiliary contact-or. Upon detection of a fault, the current is commutated into the CLD circuit. The liquid-metal vaporizes, increasing the CLD resistance and Considerably decreasing the actual current to be interrupted. This system will materially reduce the wear and tear on contactors because of the reduced interrupting requirement. the CLD is pressurized; when the current is interrupted, liquid metal flows back into the bore. Thus, it is resetting. Electrical and mechanical design principles are presented as well as materials for use, as found satisfactory in field tests on the device.

Jan 1, 1982

By Svend [Bue] Rondum

The final report contains a summary of the work performed under this contract, In addition to the report itself, other products were derived from this effort. Several hardware items were prototyped for use with underground belt conveyors, and a manual for installation and maintenance procedures was developed and published under separate cover. Recommendations have been included for implementation of the tools and the manual or, an industry-wide basis.

Jan 1, 1982

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of elastomeric noise abatement materials with a limited effort expended on the evaluation of specific treatments applied to mine timbers. Under the conditions employed, for a dimethyl silicone rubber, formaldehyde presented the major toxic threat; acrolein was the main toxic species for both polyester and polyether urethanes and an acrylonitrile-butadiene-styrene resin; in the case of flame-retardant styrene-butadiene rubber compositions, hydrogen chloride, and in the case of PFA-treated timber, furfural, were the major toxic compounds. Of the materials studied, the flame-retardant styrene-butadiene rubbers presented the greatest toxic hazard. The generated data have been reduced to toxic load tabulations amenable to employment for potential hazard assessment.

Jan 1, 1982

The Minerals Data Source Directory is a compilation of descriptive information on the availability, content, and location of minerals data in the Federal Government. It is intended to assist Government personnel and the general public in locating and acquiring minerals information. Included in the Directory are descriptions of data bases, publications, information systems, and information offices containing data pertaining to all aspects of mineral production, consumption, trade, and related information. These mineral data sources include the Federal agencies such as the Department of the Interior's Bureau of Mines and Geological Survey whose major mission is the collection and dissemination of mineral information. Also included are agencies such as the Departments of Agriculture, Commerce, Labor, State, and Treasury, and the Central Intelligence Agency, whose primary mission is the collection of data in non mineral subject areas, but in which the mineral industry is a component.

Jan 1, 1982

By D. D. Bush

Based on the results of this study, the underhand cut and fill stoping method, with mass destressing, is an effective method for controlling rock bursts and falls of ground for deep mining in the Coeur d'Alene Mining District. The procedure can be utilized to pull highly stressed pillars by converting from conventional overhand stoping methods or used as a primary recovery system. During the demonstration, only one minor rock burst occurred, with no injuries. The system facilitates accurate placement of vertical boreholes for effective mass destressing. Each mining cut is filled with cemented sandfill overlying a timbered mat that forms the back for the succeeding cut. For this demonstration, a cemented fill was mixed on the surface and piped to the stone. Costs for pillar recovery by this method are comparable and are considered cost effective over conventionally timbered overhand mining as a pillar recovery method.

Jan 1, 1982

By John H. Johnson

This report covers research which is directed toward the measurement and control of underground mine diesel emissions. The report consists of three separate reports presented as Sections 1, 2, and 3. Section 1 "Emissions Measurement Apparatus" (EMA 1) discusses the selection and evaluation of instruments and procedures to be used as part of a diesel tailpipe emissions dilution and measurement apparatus. The instruments selected for gaseous pollutants are the Energetics Science Inc.* E.S.I.) 2000 for CO, the E.S.I. 7000 for NO and N02, and the Fuji ZFP5 for C02. Particulate matter is presently measured with the Celesco 1013 Smoke Opacity Meter. The raw exhaust concentration of one of these constituents is used Lo calculate the dilution ratio. Either a modified high range E.S.I. 2000 CO instrument or a Daco Products Cobra C02 instrument can be used, but neither is totally satisfactory. The study also indicated that it may he possible to increase the sample collection time from 15 seconds to the total 30 seconds over which the engine can be loaded without increasing the probability of damaging the vehicle hydraulic systems. Section 2 "The Effect of Fuels, Catalysts and a Filter Trap on Drift Pollutant Concentrations" discusses research in the Mine Air Quality Laboratory. A Wagner ST5D LHD with a Deutz F8L714 engine was used to compare three exhaust aftertreatment devices and a muffler-only system. The effect of these four systems on CO, C02, NO and N02 and on total, soluble, sulfate, and solid particulate matter was measured in the drift and on the LHD. The filter trap successfully reduced particulate matter for both fuels without significantly increasing the concentrations of any of the other constituents. The PTX catalyst was effective in reducing CO, and soluble particulate, but significantly increased N02 and solid and sulfate particulate matter. The Oxy Cat catalyst tested didn't seem to he working on the gases, and it significantly increased sulfate, soluble arid solid particulate concentrations. Section 3 "Diesel/Coal Particulate Matter Characterization by Laser Raman Spectroscopy" covers basic research on a method for determining the percentage by weight of diesel particulate on a filter containing a diesel-coal mixture. Signal-averaged Raman spectra provide the necessary precision. The method developed is non-destructive and uses as-received filters requiring no sample manipulation. Particulate with diesel contents in the range of 10 to 50% by weight have been analyzed with accuracies better than 6%t of the mean value. A number of samples containing diesel-coal mixtures were characterized by the procedures developed and the results are analyzed in light of various spectral and other system variables including coal rank and form and diesel engine operating conditions.

Jan 1, 1982

By Robert L. Lagace

This report describes the results of a system study of the factors influencing mine rescue attempts based on the use of electromagnetic VF rescue transmitters by trapped miners and helicopterborne search receivers by mine rescue personnel. The findings cover four main task areas. The first - mine emergency/disaster considerations - concentrates on characterizing the events and key parameters of mine fires and explosions related to trapped miner location and rescue activities. The parameters include critical time periods, affected areas, survival times, response and rescue times, and survival rates. The second - hardware considerations - concentrates on characterizing the relevant properties of VF rescue transmitters, oxygen-type self-rescuers, VF search receivers, helicopter performance, and signal detectability and sensor sweepwidths for helicopterborne sensors. The third - search theory probabilistic model develops a method to identify the most important regions to be searched, and to allocate helicopter-based search effort so as to maximize the number of miners detected in time to be rescued. The fourth - sensitivity analyses and application of the search model - exercises the search model on representative mine emergency/disaster scenarios to assess the impact and effectiveness of helicopter-based searches. Conclusions and recommendations are presented, together with a set of search scenario planning guidelines.

Jan 1, 1982

By J. A. Bartol

A survey was made of accident data and operating practices related to overloading and uneven load distribution on haulage trucks in noncoal open pit mines. Safety and economic aspects were analyzed. A bibliography of the literature was prepared. Review was made of available or projected systems for weighing or load indicating that might be applied to haulage trucks. A model specification was prepared for an overload detection system. Several promising systems for overload detection were identified. One was installed and tested briefly in a 170-ton rear dump truck in a copper surface mine.

Jan 1, 1982

By L. A. Morley

This report summarizes the work performed on Bureau of Mines Contract J0199106, "Portable Trailing Cables, Splices, and Couplers - Design and Installation Considerations," from May 1, 1979 until December 31, 1981. Splice installations and considerations for the possible use of conductive-rubber shielding in low-voltage trailing cables as well as coupler installations in high-voltage cables were the principal tasks. Flammability measurements on cable components and general testing facilities for mine electrical equipment were secondary tasks. Theoretical and empirical data indicate that conductive rubber with high resistivity values is an unsatisfactory shield design for current-sensing fault detection. Elimination of partial discharge in coupler installations requires meticulous care.

Jan 1, 1982

Effective control of respirable dust is one of the most serious problems associated with longwall mining in the United States. This report describes the development and laboratory testing of dust collectors for use on double drum shearers. Systems tested included: ? High Capacity Flooded Bed Scrubber ? Water Powered Extraction Cowls ? Water Powered Extraction Drums ? Water Powered spot Scrubbers. The systems were tested using tracer gas in a full-scale model of a longwall shearer face. This report provides a detailed description of the test facility, test methods, and system test results.

Jan 1, 1982

By J. E. Cleveland

The major health concern for uranium miners is the release of radon gas and the resultant ingrowth of the short lived daughters in the mine atmosphere. Present methods of control are the utilization of mine ventilation systems for dilution and control of ingrowth time to maintain working levels below those set by regulations. This study examined pressure cycling efforts on the radon emanation. The mechanical ventilation systems were altered to allow pressure changes throughout the mine to increase radon influx during the off shifts and thus deplete the sources of radon gas. Continuous radon working level and environmental monitors, developed by the Bureau of Mines, were employed to monitor radiation and physical parameters in the mine workings. The mine ventilation system was then varied to induce radon flows during off shifts, thus, depleting the radon sources during normal production shifts. Electro-static precipitators were also tested to determine radon daughter collection efficiencies. Both radon and radon daughter concentrations were monitored and evaluated. Major problems were found in the simple mechanical operation of cleaning these units.

Jan 1, 1982

By Donald Koch

The project investigated regional impacts of mining on the ground water system of the Powder River Basin by: 1) establishment of a regional ground water monitoring network. and 2)development at a set pit digital computer models to simulate ground water flow and quality, ground water contributions to surface water flow and quality (i.e., baseflow), and watershed run-off and recharge. Over 100 wells were monitored for physical and chemical parameters. Data were used as input to the models and for the development of a comprehensive data base. The basin was modeled on a regional and subregional scale using a finite -difference model employing an alternating difference technique. Two water-shed models were evaluated fur their ability to provide runoff and recharge inputs to the basic ground water model. Application of the regional and subregional models using conservative mining scenarios showed that drawdowns may extend west from the mines as far as ten miles but that impacts would be insignificant on a regional scale. The watershed model could be effectively applied to small watersheds only.

Jan 1, 1982

Research 82 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary. General information on Bureau of Mines programs is available from the Office of Technical Information, 2401 E Street, NW., Washington, D.C. 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1982

This work examined the feasibility of in-mine coal preparation in two phases. Phase I included a survey of previous investigations and a preliminary analysis of the economic and technical feasibility on a selection of representative sites and degrees of cleaning. The contract was terminated at the end of Phase I. The preliminary analysis determined that in-mine preparation systems can be applied using currently available technology. The most likely mines for application will have shaft or slope access and be deeper than 500 feet. The refuse disposal systems technically feasible are (1) pneumatic placement of coarse refuse in room and pillar panels or longwall faces, (2) mechanical placement of coarse and fine fractions in room and pillar panels, and (3) hydraulic placement of fine fractions in room and pillar panels. The economic feasibility is much more dependent on the refuse disposal-system than on the preparation system. It is estimated that the capital cost of an in-mine preparation and disposal system would be $6.00 per clean ton and the operating cost would be $1.24 per clean ton for a 1 million clean ton per year mine.

Jan 1, 1982

By Steve C. Albrecht

The objective of this study is "to assess the impact of surface mining on soil compaction in the Midwest". The study revolves around a unique field sampling program targeted at four mine sites utilizing four distinct types of soil movement of midwestern prime land. Through the preparation of a final report for use as a guidebook, an assessment is made of the degree to which surface mining operations contribute to the soil compaction problem. The final report is formulated through the use of field study data as well as information gathered in an intense literature review. The final report centers on applying collected data to practical field applications. Soil sampling on the four mine sites centers on a comparison of natural and replaced soils for moist bulk density. This characterization evaluates changes in density and texture throughout the soil profile to a depth of 48 inches. Fertility of the topsoil is also assessed for natural and replaced soils. During field sampling and observations, a base of information has been gathered to compile a case study on each mine site. The report accesses the regulations in the prime farmland areas through the use of a matrix. The regulatory matrix allows easy access of mining personnel to State and Federal regulations.

Jan 1, 1982

By H. A. Wright

This report assesses the economic, legal, institutional and technical factors that affect the current and future status of implementation of mine monitoring systems in the United States. It begins with a description of a poll of the Mining Production Research Committee and the Mine Monitoring and Communications Committee of Bituminous Coal Research that was conducted to establish industry monitoring needs and constraints. Existing systems in the United States and foreign countries are then reviewed and compared with the requirements set forth by the industry committees. At the same time, state and federal mining laws are reviewed, and equipment currently available from suppliers of mine monitoring systems and components is discussed. A framework for cost/benefit analysis is established and a series of case examples for various monitoring functions are presented. The total values of the market for mine monitoring systems in 1980 and 1990 are estimated on the basis of industry statistics and system cost estimates.

Jan 1, 1982

By James L. Eirls

The objective of this project was to improve a driver's field of view for large trucks used in the mining industry. Rearward viewing was enhanced by improving the rear-view mirror designs. Rear vision was accomplished using a closed circuit television system. Views ahead,, to the right, and downward were obtained with a blind area viewer (BAV). The BAV is a unique combination of fresnel lenses housed in a shielded, environmentally protected enclosure that produces an image of the area in front of and downward 70° and to either side of the BAV 300. The improved visibility devices were evaluated by long-term, in-mine testing. The right Bide mirror (RSM) and BAV provide the greatest improvements for the least cost and are commercially available. Application of the RSM and BAV should achieve a reduction in accident potential and greater vehicle productivity by enlarging and improving the equipment operator's visibility and making priviously blind areas and hazardous situations detectable.

Jan 1, 1982

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By Michael A. Anuta

This report describes the potential for utilization of satellite observations for remote sensing of mine waste disposal areas. Four study sites consisting of metal and nonmetal mining areas in different climatic and physiographic regions of contigous United States were used in this investigation. The mine waste disposal sites consisted of mining of phosphates in Florida, copper in Arizona, silver in Idaho, and coal in West Virginia. Landsat satellite multispectral scanner observations were used together with aerial photographs, ground surveys, U.S. Geological Survey maps, and other ancillary information. Landsat digital data were categorized using automated supervised classification algorithms and an image analysis system. Detailed description of automated classification techniques employed and the accuracy attained is provided together with the results of manual interpretations. The inventory of areas distrubed for phosphate mining and a change detection investigation for-Polk County Florida were also undertaken during this study.

Jan 1, 1982

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1980 was $328.6 million, a decrease of $7.8 million from 1979. Cement, crushed stone, lime, clays, and sand and gravel continued as the major commodities produced. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in native asphalt, ferroalloys, kaolin, and oyster shell; fourth in dimension marble, masonry cement, and bentonite; and fifth in fire clay and lime. Alabama ranked in the top 20 States in total value of non-metallic minerals produced. Adverse economic conditions in the construction and metals industries impacted on the minerals industry in Alabama. Mineral producers supplying raw or finished materials to these industries experienced periodic reductions in sales during the year. Unit price increases did not keep up with inflation.

Jan 1, 1982