Search Documents

The value of raw nonfuel mineral materials production totaled an estimated $19.7 billion in 1978. The record 1978 value exceeded by 13 percent the 1977 value of $17.5 billion. This raw mineral output was the basis for approximately $200 billion worth of processed materials of mineral origin. Output of both metals and nonmetals increased about $1 billion each, above comparable figures for 1977. Of the 22 metals produced quantitative output of 11 increased and the value of 13 increased. Among the 48 nonmetallic commodities produced, the quantities for 35 increased, and the values for 40 increased.

Jan 1, 1979

By M. S. Fleming

The objective was to evaluate central lubrication systems for potential use on underground mining equipment. Previous use on continuous mining equipment resulted in poor system performance because of improper selection of lubricants, component failures, and an inconsistent delivery of lubricant to the bearings. The principles and operational characteristics of systems are reviewed and evaluated, and it was concluded that systems are available which can provide reliable central lubrication if properly applied, installed, and maintained. The procedures for applying a system to a continuous miner are discussed. Investigation revealed the lack of significant information on lubrication-related equipment failures and injuries related to maintenance and repair operations, the lack of significant failure rate data for central lubrication system components, and the lack of performance standards for central lubrication systems and components. To continue the development of systems for underground mining equipment it is recommended that a data bank on failures and reliability for equipment with and without central lubrication systems be created, and standardized specifications and performance criteria be developed for central lubrication systems and components which will be used on underground mining equipment.

Jan 1, 1979

By D. A. Paice

A power supply to operate fluorescent or mercury vapor lamps from 300 volt dc coal mine trolley wires has been developed for the Bureau of Mines. A high frequency regulated inverter unit incorporates ballasts for a mix of lamp loads up to 650 watts. For 600 volt trolley systems an additional power converter unit was developed to step down the dc voltage to 300 volts for the inverter unit. Both units have operated in a working coal mine for over 12 months without need for servicing. The lamp load in these tests included two 100 watt mercury vapor head lamps and six 75 watt fluorescent lamps.

Jan 1, 1979

This Bureau of Mines publication contains five papers pertaining to the effective grounding of mine power systems, as follows: Ground-check monitor types and safety characteristics; ground wire monitors for surface coal mines; ground bed design and measurement; electrical ground rod corrosion; and a continuous ground bed resistance monitor.

Jan 1, 1979

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

By S. J. Hussey

A jig tailing with gold content ranging from 0.33 to 0.43 oz/ton was leached in weak cyanide solution with extractions of up to 97 pct in 24 hours. By countercurrent batch leaching studies and laboratory pilot plant operation, minus 10- plus 20-mesh and minus 6- plus 16-mesh coconut carbon were loaded to 700 oz/ton of Au. Minor silver in the ore reported in the carbon in amounts of up to 100 oz/ton. Gold adsorption rate data and an equilibrium adsorption curve for minus 10- plus 20-mesh carbon at ambient temperatures were developed and used in the successful application of a cascade design theory. The work was performed as a part of the overall Bureau of Mines research effort to help maintain an adequate domestic supply of metals by making improvements in mineral-processing technology.

Jan 1, 1979

By Charles G. Howard

Accidents involving underground rail transport were analyzed to quantify the magnitude and the operational requirements for individual mine car braking systems. The results showed that the brake preventable accidents represent only 2% of the total underground fatal accidents and less than 1% of the total underground nonfatal accidents. In addition, the brake preventable accidents are expected to decline over the next decade. The costs of accidents involving deaths and Injuries were determined using various well accepted methods. The costs of a brake retrofit program for all operating underground coal cars were developed separately for small and large coal mines. Costs of retrofit brakes, new car brakes, maintenance, inspection and repair facilities were included in the esimates. The analysis showed that a retrofit program would not significantly increase safety, and that the program cost would greatly exceed the corresponding expected benefits.

Jan 1, 1979

Toward the goal of maximizing minerals and metals recovery from domestic resources, the Bureau of Mines, U.S. Department of the Interior, has conducted in situ corrosion studies at the Salton Sea Known Geothermal Resources Area (KGRA) in the Imperial Valley, Calif., to evaluate and characterize materials of construction for geothermal resources recovery plants. General-, pitting, and crevice-corrosion characteristics of 13 commercially available alloys were investigated for periods of 15 and 30 days in seven process environments expected to be found in typical geothermal resources plants. Stainless steel alloy 29.4, Inconel 625, and the Hastelloys G, S, and C-276 were the most resistant to general corrosion, did not pit, and exhibited little susceptibility to crevice corrosion. Stainless steel alloys 430, E-Brite 26-1, and 6X had low general corrosion rates, but pitted and were susceptible to crevice corrosion. Stainless steel alloy 316 L had a low corrosion rate, but corroded intergranularly, pitted, and was susceptible to crevice corrosion and to stress-corrosion cracking. Titanium-1.5 nickel and TiCode-12 had low corrosion rates, did not pit, and were not susceptible to crevice corrosion. Carbon and 4130 steels had high corrosion rates, pitted, and had high susceptibilities to crevice corrosion. The major scale-forming mineral on the corrosion samples in most of the process environments studied was galena mixed with lesser amounts of other minerals.

Jan 1, 1979

By L. Keith Hudson

The purpose of this study is to provide data that demonstrates that the Alcoa flash calciner design can be used for the decomposition of AlCl3?6H2O to A1203. Heat and material valance data for calcination provides data on the partial pressure of HCl in the off-gases. Experimentally determined data for the HCl partial pressure, over solutions expected in producing alumina from clay by the hydrochloric acid process, show that HCl can be absorbed from the off-gases into process solutions to effect crystallization of AlCl3?6H2O.

Jan 1, 1979

Measure the leakage through individual crosscut stoppings quickly and economically so that the worst ones can be identified and repaired. (Typically 60 to 80% of the air supplied to a mine short circuits before reaching a working face.) Approach Most of the leakage through a permanent stop-ping is channeled through two windows in a temporary stopping, and air velocities through the windows are measured; leakage is determined from a formula. How It Works A temporary stopping made of plastic brattice is erected in the same cross cut as the permanent stopping, either upstream or downstream. The brattice is fastened to the roof, bottom, and ribs of the entry with spads. Normal leakage of brattice was allowed for in deriving formula, and does not effect results. For best accuracy the brattice and the stopping should be separated by a distance of one hydraulic diameter.

Jan 1, 1979

By John T. Dieckmann

This report documents the work performed and the results obtained in a 2-year development of a Mobile Inert Gas Generator for use in the Bureau of Mines Remote Sealing System for fighting underground coal mine fires. The performance requirements of an inert gas generating system for the Remote Sealing System were clearly established. A thorough review of seven possible system designs meeting these requirements was conducted. An air cooled, distillate oil fired combustion type inert gas generator was selected for further detailed design, hardware fabrication, and performance testing. The Inert Gas Generator constructed under this program has been thoroughly performance tested and has been operated in the field for approximately 200 hours. The system has met or exceeded all important performance requirements. The system was used in the fire fighting efforts at the Bethlehem Mines Corporation Cambria Division Mine 33 fire and contributed to the successful containment of the fire. The system was also employed in the demonstration of entire Remote Mine Sealing System at the Jenney Mine in the fall of 1978. The system is currently avail-able for fighting any future underground coal mine fires.

Jan 1, 1979

By J. Hanslovan, R. H. King

An investigation of the feasibility of shielding low-voltage trailing cables in underground coal mines is described. Both laboratory and under¬ground installation results are presented. The main objective of shielding is to reduce the electrical shock hazard; however, several problems will be encountered by mine operators who install shielded cables. Parameters related to such items as purchasing, splicing, troubleshooting, safety, and reliability are discussed. Some of these problems can be minimized by changes in cable constructions and shuttle-car reeling-device components. Both SH-C and SH-D constructions are considered.

Jan 1, 1979

By R. C. Butman

The Lincoln Terminal System (LTS) is a stand-alone computerized training device that presents high quality visual displays, and audio messages to a student. A keyboard is provided for student input. A variety of student-machine interactive programs arc provided. These programs allow the author/instructor to evaluate numerical entries and responses to simple and compound multiple-choice questions (where a compound choice is defined to be more than one choice, ordered or unordered from one or more list(s) of choices. Descriptions of LTS applications, lesson development procedures, hardware provided and support facilities required are given. A contract history summary, and a bibliography of reports published under three successive BoM contracts supporting LTS development, is provided.

Jan 1, 1979

By Charles D. Litton

An overview of state-of-the-art technology in fire detectors is presented by the Bureau of Mines regarding their use in the mining industry. Detectors are categorized according to the characteristics of a fire to which they respond. Operating principles of the various detectors, their application, and the advantages and disadvantages of each are discussed.

Jan 1, 1979

By A. T. Iannacchione, D. G. Puglio

This Bureau of Mines study covers 25 underground mines that were active in the Upper and Lower Freeport and Lower Kittanning coalbeds in 1976. The coal ranges from low to medium volatile in rank; its primary use is for steam generation. Seven mines emit more than 100,000 cfd of methane gas; those mines are the deepest and largest producers. The methane gas content of three core samples of the Lower Kittanning coalbed was estimated by the direct method. A sample from a depth of 320 feet contained 0.5 cu cm of gas per gram, at 620 feet there was 0.8 cu cm of gas per gram, and at 1,060 feet there was 11 cu cm of gas per gram. These results suggest that methane control problems will be encountered in the future as deeper coal is mined.

Jan 1, 1979

By Harold L. Rhodes

The Bureau of Mines has developed a method for determining the H2S content in natural gas samples. A gas chromatograph with a flame photometric detector was used to analyze samples with H2S concentrations ranging from 5,000 ppm to a minimum detectable limit of 0.01 ppm. A mass spectrometer was used to analyze samples containing H2S in amounts greater than 5,000 ppm. Methods are presented for preparing containers for H2S samples and for preparing standards using partial pressure and weighed standard methods, Sample collection techniques are discussed, as are analytical results which illustrate the loss of H2S while in the sample container and provide a basis for evaluating containers used for sampling and standard preparation.

Jan 1, 1979

By John Durkin

A computer model has been generated to evaluate speech intelligibility of individuals wearing conventional and electronic hearing protectors. For speakers talking at normal levels in noise levels of 65 db(Lp) or less, it was found that conventional hearing protectors significantly reduced speech intelligibility. Under the same conditions, electronic protectors provided scores equal to those for the unprotected individuals while providing protection from high noise levels. Therefore, electronic hearing protection is valuable in areas where high noise level is intermittent.

Jan 1, 1979

By Robert W. Freedman

In the Bureau of Mines study, a filter with a 20-by 20-inch-square cross section was inserted into the exhaust ducting of a 4-stroke-cycle, 90-hp diesel engine, and the efficiency of removal of total particulate was measured gravimetrically as a function of time. Removal efficiencies were close to 90 pct during the main portion of several extended runs employing several combinations of filter beds. Variations in engine load had little effect on collection efficiency. Particle size as measured by a Bureau-developed online instrument centered on 0.07 m based on number count. Removal efficiency increased rather sharply for both larger and smaller particles.

Jan 1, 1979

Permit visual inspection of underground cavities dam the surface. Approach A closed circuit TV camera and a 35mm still camera are lowered down a borehole, and remotely operated. How It Works A platform holding the cameras, and other equipment is lowered on a graduated cable until the depth of interest is reached. Then a quartz lamp and the TV camera are turned on. The television picture is monitored at the surface and recorded on video tape. Areas of special interest are photographed with a 35mm still camera. These photographs contain more detail than TV images because photographic film is capable of higher resolution than a TV transmission.

Jan 1, 1979

Mitsui Aluminium Co. of Japan announced that it would finance 25 percent of the construction costs for the 217,000 ton-per-year primary aluminum smelter being built by Alumax, Inc. at Holly, SC. Mitsui would receive 25 percent of the plant's production in return. Construction on the smelter began early in 1978, and is scheduled to be completed in 1981. The Aluminum Company of America (Alcoa) announced plans to restart a third potline at its Point Comfort, TX primary aluminum smelter in July. The company previously announced plans to restart two potlines at the facility in May. Reynolds Metals Co. began preparations to restart primary aluminum production in May in one of two 57,000 ton-per-year potlines at its Corpus Christi, TX smelter. The plant has been closed since 1975.

Jan 1, 1979