Search Documents

By Mukund O. Gangal

A deep cutting continuous miner, HH456, was tested under production-mining conditions at the Joanne Mine, Rachel W. Va., for about 1 ½ years (226 production days). The miner was run in two modes: a low head-rpm, deep cutting and high rpm, shallow-cutting mode. These tests confirmed that deep cutting and slow cutter speed reduce respirable dust significantly under production mining conditions. Quantitative reductions in dust, in deep vs shallow cutting, were 73°; in return air and 63% at the operator's location. Production rate, (tons/shift), and bit consumption rate did not show any relationship to deep or shallow cutting. Reliability and maintainability of the miner were worse in deep cutting mode due to cutter drive shaft failures; the cutter shaft problem was solved through improved material and design. Excluding the cutter shaft repairs. maintainability war similar for deep and shallow cutting,

Jan 1, 1979

Continuously monitor air-borne radon daughters that are a hazard to underground miners. Approach A beta detector continuously counts beta activity collected on a filter paper to allow calculation of exposure in working level units. How It Works At each Site a constant flow pump draws mine air through a fiberglass filter located in front of a beta detector (pancake type Geiger Mueller tube), Radioactive particles (products of the radon 222 gas emanating from the mine walls) collect on the filter and decay, releasing alpha and beta particles as well as gamma rays. A portion of the beta particles penetrate the Geiger tube window and create electrical pulses in the tube. These pulses are then amplified and sent by a coaxial type or shielded electrical cable to a central monitor located some distance from a working level detector. At the central monitor incoming Signals are amplified and fed into two channels, (See the block

Jan 1, 1979

By Laird Crocker

A goal of the Federal Bureau of Mines is to minimize the undersirable environmental conflicts and impacts associated with mineral processing operations. To help reach this goal the Bureau operated a citrate-process pilot plant for the removal of sulfur dioxide from lead smelter sintering machine waste gases to test the process. The process uses a carboxylate solution such as citric acid to absorb sulfur dioxide from waste gases. The absorbed sulfur dioxide is subsequently reacted with hydrogen sulfide to precipitate sulfur and regenerate the solution for recycle. Nominal capacity of the pilot plant was 1,000 scfm of 0.5 vol-pct sulfur dioxide gas. The pilot plant was operated for over 5,400 hr and produced about 55 net tons of sulfur. The operation demonstrated that (1) 99 pct of the sulfur dioxide could be removed from lead smelter sintering machining waste gases containing from 0.1 to 0.6 vol-pct sulfur dioxide, (2) sulfur precipitation and solution regeneration with hydrogen sulfide in conventional stirred vessels was readily controlled, (3) precipitated sulfur could be continuously recovered as a 99.S-pct-pure product by flotation and melting, and (4) 78 dry-vol-pct hydrogen sulfide gas could be produced from pilot-plant product sulfur, natural gas, and steam.

Jan 1, 1979

By John E. Lambert

Automatic control of drum head continuous mining machines was investigated as a means of reducing respirable dust generated and operator variabitity. Literature survey, manufacturer interviews and mine visits were the major information sources. Technically feasible automation concepts were Identified to control sump and shear rates, cutter head elevation limits and sumping distance. These are the elements of a programmed cutting cycle which maintains peak penetrating force on the cutter, to maximize depth of cut and therefore reduce dust generation. Based on the industry surveys, successful underground hardware demonstrations must be completed in order to stimulate the market demand for these advanced control features.

Jan 1, 1979

By C. B. Davison

One goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. Consistent with this goal, the Bureau conducted studies on the formation of undesirable cristobalite in seven different fire clays used as refractories. The studies employed scanning electron micrography, chemical and X-ray analyses, and pyrometric cone equivalent determinations to examine the sample clays and determine the effect of thermal history and stablilizing additives on the amount of cristobalite in various calcines. This research has indicated that as fire clay calcining temperatures increased from 1390° to 1,490° C there was a gradual decrease in the percent of cristobalite present in the calcines and a progressive development of mullite crystallization. No cristobalite was found in fire clays calcined above 1,550° C, but cristobalite reappeared when the calcines were reheated to temperatures between 1,400° and 1,500° C. The research also revealed that additions of lithium fluoride (LiF) prevented formation of cristobalite in fire clay calcines.

Jan 1, 1979

By Robert L. Lagace, Alfred G. Emslie

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

By Staff

This Bureau of Mines publication contains five papers pertaining to the effective grounding of mine power systems, as follows: Ground-check monitor types and safety characteristics; ground wire monitors for surface coal mines; ground bed design and measurement; electrical ground rod corrosion; and a continuous ground 'bed resistance monitor.

Jan 1, 1979

By R. Sainath, Wils L. Cooley

Continuous monitoring of ground bed resistance is essential to insure a low-resistance path for fault currents, lightning strokes, and electrostatic discharges. This paper explains the salient features of the continuous ground bed monitor and its applications. The importance of a low-resistance path to ground is highlighted. Sample readings obtained with the ground bed monitor are included, and typical applications of this instrument are illustrated. This effort was supported by the U.S. Department of Interior's Bureau of Mines under USBM grant G0144138.

Jan 1, 1979

By George M. Lucich

This report describes a sensitive, proportional temperature controller developed by the Bureau of Mines that is useful in the temperature range from 40 to 400° C with an accuracy of ±0.10 C. A temperature controller of this kind is potentially useful for regulating temperatures in air chambers, liquid baths, furnaces, and reaction vessels, and for other applications. This instrument was developed to control the duration and temperature of the heating cycle of a charcoal-filled adsorber that is part of a special helium analyzer used by the Bureau. The controller was made from commercially available parts, and can be easily modified to provide continuous temperature control. The circuit is solid state and employs no electromechanical devices. Over a 2-year period of use as a component of the special helium analyzer, this temperature controller performed successfully and required no maintenance.

Jan 1, 1979

This Bureau of Mines report concerns two subjects important in the application of electric power in mining systems. Electrical transients and their suppression are discussed, and several considerations are explored with regard to the use of explosionproof or other electrical enclosures.

Jan 1, 1979

By Michael J. Magyar

The Federal Bureau of Mines has developed a hydrametallurgical method to recover aluminum, aluminum oxide, and fluxing salts from aluminum salt slags. The slag is leached with water at room temperature to produce a saturated brine slurry. Screening of the slurry yields an aluminum-rich fraction that can be returned to the dross furnace. The remaining slurry is vacuum filtered, yielding a clear brine solution and an aluminum oxide filter cake. Evaporation of the clear filtrate produces a high-purity fluxing salt for reuse in the dross furnace. Over 80 pct of the metallic aluminum is recovered in the aluminum-rich oversize fraction, while essentially all the fluxing salts are recovered by evaporation. This report contains the final results of an investigation on a process research unit scale, an economic evaluation of the method, and recommendations to further improve the process.

Jan 1, 1979

By D. G. Puglio

This Bureau of Mines study covers 25 underground mines that were active in the Upper and Lower Freeport and Lower Kittanning coalbeds in 1976. The coal ranges from low to medium volatile in rank; its primary use is for steam generation. Seven mines emit more than 100,000 cfd of methane gas; those mines are the deepest and largest producers. The methane gas content of three core samples of the Lower Kittanning coalbed was estimated by the direct method. A sample from a depth of 320 feet contained 0.5 cu cm of gas per gram, at 620 feet there was 0.8 cu cm of gas per gram, and at 1,060 feet there was 11 cu cm of gas per gram. These results suggest that methane control problems will be encountered in the future as deeper coal is mined.

Jan 1, 1979

By J. S. Hansen

In support of its objective to conserve mineral resources by minimizing premature failure of materials, the Bureau of Mines conducted a cooperative study with the U.S. Department of Energy on the erosion and abrasion resistance of hard materials for valves in coal conversion systems. This report describes a newly developed erosion-testing apparatus and presents data on the erosion resistance of over 200 materials. Erosion resistance of most metals was comparatively low. In contrast, ceramics and cermets such as B4C, WC, SiC, Si3N4, and TiB2, when fabricated to minimize porosity, displayed greater than five times the erosion resistance of metals. Coatings such as boron diffused into Mo and WC, chemical-vapor-deposited TiCN, and electrodeposited TiB2 were highly erosion resistant if applied in thicknesses ranging from 60 to 75 µm. Erosion resistance of cemented carbides was inversely related to metal binder content.

Jan 1, 1979

By S. Ralph Austin

This Bureau of Mines investigation determined the effects of so-called annealing at high temperatures on radon-222 emanation from domestic uranium ores. Concurrently, a method was developed for closely estimating the emanation coefficients of hot samples from measurements of their gamma activity after cooling. Emanation coefficients of 102 samples from 14 domestic areas of past, present, and possible future uranium production were investigated using modifications of the closed-can, gamma-only assay method at and after cooling from 100° to 1,000° C. True annealing probably does not occur below 500° C. In limited investigations at 500° C and above, effects of annealing are masked by the effects of other parameters. Emanation is commonly less at one or more of the steps investigated in the 100° to 500° C range than before heating. This decrease is tentatively attributed to water loss at temperatures dependent upon the minerals present. The average sample emanates least at 300° C; emanation increases with higher temperatures to at least 900° C. Emanation decreases sharply on cooling, but it is partially restored by prolonged exposure to the atmosphere at room temperature. Higher than average emanation of coffinite ores at 500° C and above may be related to destruction of the coffinite crystal structure.

Jan 1, 1979

By Max L. Glenn

As part of its goal to minimize requirements for mineral commodities through conservation and substitution, the Bureau of Mines conducted research to develop molybdenum as a potential substitute for superalloys containing the strategic and critical materials, nickel, chromium, and cobalt. Since molybdenum requires protection from oxidation at high temperatures, several complex oxides of the spinel and perovskite structure were investigated to determine which possessed the greatest potential for use as oxidation-barrier coatings. Two spinels (MgCr204 and MgA1204) and five perovskites (BaHfO3, YCrO3, NdCrO3, BaZrO3, and LaCrO3) were selected for testing. Various high-temperature prop¬erties that are important for oxidation-resistant coatings were examined, including diffusion rates of oxygen and molybdenum, recession (vaporization) rates, hardness, erosion resistance, sinterability, reactivity with molybdenum, and ease of application. From the evaluation of high-temperature properties, two spinels (MgCr204 and MgA1204) stand above the other oxides as possible coatings for molybdenum. However, laboratory coatings of MgCr204 at 1,360° C (2,480° F) are equivalent or inferior to currently available MoSi2 coatings; laboratory coatings of MgA1204 may be comparable under limited conditions to currently available MoSi2 coatings at the same temperature.

Jan 1, 1979

By William J. Karwoski

To improve rock-burst control in deep vein mining, a field demonstration has been carried out by the Bureau of Mines to test a new rock-burst control concept--rock preconditioning in advance of mining. The procedure is to fracture the major rock-burst-prone zone during the development of each level before production mining. This allows initial mining to begin in a preconditioned zone and later mining from the level below to end in a prefractured or preconditioned pillar zone that is relatively burst-free. This full-scale field demonstration was carried out On the 7700 level of the Hecla Mining Co.'s Star-Morning mine. An expected burst-prone zone along the main vein between 7 and 10 crosscuts, some 250 feet long by 40 feet above and below the level, was preconditioned by blasting a fanlike ring of drilled holes from each crosscut. The drill holes, up to 100 feet long and 4 inches in diameter, were loaded with high explosives and shot. About 4,550 feet of drilling and 9,000 pounds of explosives were involved in the effort. Comparison of preshot and postshot data from monitoring instrumentation indicated that the blasting did fracture the rock in the planned zone and did result in an immediate stress decrease and softening of rock. The field data compared favorably with predicted results from a finite-element computer model simulation of the destressing. Based on observations made during mining and on the data from the Hecla rock-burst monitoring system, there is no doubt that this preconditioning in advance of mining demonstration resulted in much-improved rock-burst control during first-floor mining. It was also concluded that preconditioning the vein was more effective than preconditioning the wall rock.

Jan 1, 1979

By Staff

This Bureau of Mines report is devoted to descriptions of investigations pertaining to underground mine trailing cables, their handling, splicing, and the use of couplers.

Jan 1, 1979

By Robert C. Weisner

Current production costs and market conditions in the potash industry of the Carlsbad area were studied to determine the potential values of the potash mineral resource that would be lost or foregone if the Waste Isolation Pilot Plant (WIPP) facility is constructed on the proposed site in that area. The purpose of the WIPP project is to investigate the possibility of developing a nuclear waste disposal plant in the salt formations at the site. Analyses were made of all potash deposits determined to be in the site. Mining and processing under the most favorable recovery systems were considered. Value determinations were based upon estimated operating and capital costs of current mine-mill operations in the Carlsbad area. This study was made for the Energy Research and Development Administration (ERDA) by members of the Federal Bureau of Mines Minerals Availability System staff.

Jan 1, 1979

By John D. Rockaway

Failure of the mine floor supporting coal pillars frequently occurs when the subcoal strata include "underclays" or other low strength strata. The failure process has been studied to define the response of these materials to applied coal pillar loads and to determine the applicability of bearing capacity analysis to evaluate unsafe conditions. The study has been accomplished through an investigation of both the intact and insitu geotechnical properties of the subcoal strata and through the installation of floor movement monitoring instrumentation. The results of these studies have indicated that both the shear strength of the underclay and the stratigraphy of the subcoal strata must be considered in the analysis. The shear strength was the major controlling factor determining the ultimate load carrying ability of the materials, but the thickness and stratigraphic position of the weak layers influenced the mechanism of the failure process. The methods of bearing capacity analysis were used to define pillar stability that included provisions for taking into consideration a two-layer system. Conditions assumed for a coal mine where a weak underclay overlies firmer strata. The results of the analysis compared very well with observed mine conditions, indicating marginal conditions in areas of the mine which later experienced pillar support failure. In addition, a "heave factor" was derived to predict potentially unstable floor conditions in the mines studied in detail.

Jan 1, 1979

By Jean J. Tancous

Chromium recovery from wet-blue offal trimmings and shavings can be done with substantial chemical cost gains by incineration at 600° C for 5 hr. Pretreating the offal with 0.5 M Na2C03 and air-drying prior to incineration produce Cr04 .By simply incinerating the offal, without pretreatment, an ash containing water insoluble Cr203 was produced. The Cr203 in the ash was purified by leaching with water. Chromium and crude protein were efficiently extracted from offal using 5 pct Na103, 5 pct H2S04, and 3 pct NaCl at 40° C. This procedure was effective but expensive. Satisfactory leather as to odor, appearance and shrinkage temperature was made from chromium recovered from wet-blue offal by incineration and by extraction. Chromium conservation is possible by recycling chromium liquors and by precipitating chromium from spent tanning liquors prior to combining these liquors with other tannery wastes. Combining chromium liquors with other wastes introduces contaminants that make chromium recovery and reuse difficult. Leaching sludges with H2SO4 produced marginal chemical cost gains. Leather tanned with these solutions had satisfactory shrinkage temperature but the sludge odors and iron contamination were objectionable.

Jan 1, 1979