Search Documents

By Ronald H. Church

As part of the Bureau of Mines health and safety research program in strata control, a ground-penetrating radar (GPR) system capable of pene-trating approximately 10 ft into the mine roof has been devised to identify anomalistic conditions. The GPR system consists of a transmitter with carrier frequencies of 250, 500, and 1,000 MHz, utilizing a dipole antenna, and a receiver, consisting of a dipole antenna fed into a sampler with a time base housed in a storage oscilloscope. A computer was utilized for data acquisition and data processing. Data analysis by computer enhancement revealed recognizable return ra-dar signatures from the middle man rock and main roof of the test site. These stratigraphic anomalies can be cataloged for recognizable fea-tures, which from the past history of the mine may have been shown to create strata control problems. Early recognition of such features could lead to immediate corrective actions and result in the saving of lives.

Jan 1, 1985

By Michael F. Dunn

Since crushing of rock to a smaller size is an integral part of almost any mining and quarrying operation, a study was carried out to identify and develop improved techniques for alleviating a major cause of accidents and work stoppages arising when an oversize luck or boulder lodges in the throat of the crusher. The configurations and operations of various crusher types is described, sources of boulders in the mining operation, and a detailed review is made of mining, quarrying, and construction regulations for all states, Canada, and the Federal Government for applicable provisions. Representative mines were visited and other operations contacted for their boulder handling techniques where it was found that blasting techniques used included mudcapping, bombs, and blockholing, often done very crudely and inefficiently with poor practices and various mechanical systems were used such is hooks of, overhead cranes, impact hammers, and grapplers. Safety analyses of all methods pointed out the hazards associated with blasting in the open and the dangers of entering a crusher. Boulder blasting can be done in a safer fashion if a planned step-by-step procedure is followed, and inherently safer blasting products such as exploding bridge wire blasting caps and improved blockholing techniques. In general, though, the installation of a suitable mechanical system such as an impact breaker will prove safer and cost effective even in a smaller mine or quarry.

Jan 1, 1981

Improve the safety of mine workers by developing a sensitive ground-fault relay system capable of detecting and isolating low level ground faults and thereby minimize the danger of electrocution. Approach Inadvertent, direct contact with energized conductors in underground coal mines is a major cause of electrocutions. Although relay systems designed to protect workers against such fatal accidents do exist in some industries, there are no effective ground-fault-sensing relay systems that address the special problems presented by power systems designed for U.S. mines. The Bureau of Mines conducted research to design and construct a sensitive ground-fault relay for use with low-voltage, alternating current (ac) mine electrical systems. Such a relay, sensing current leakage or faults in an electrical system, would send a trip signal to a circuit interrupting device which would then shut down power.

Jan 1, 1986

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining Co.'s Granite Mountain shaft. How this insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the lire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest pro¬ducer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

By W. H. Oppelt

The Federal Bureau of Mines investigated combustion of lignite in domes-tic heating equipment to obtain information on equipment performance and to evaluate testing procedures. Three types of domestic heating equipment were tested, ranging from a hand-tilled, magazine-type space heater to a ram-type overfeed stoker. Lignite was readily burned in each of the three units under various test conditions. Burnoff rates determined by adding weighed charges to the magazine were found to be in error because of shrinkage of the lignite when only a portion of the magazine capacity was consumed during a test. More reliable burnoff rates could be determined by carbon-nitrogen balances. A hand-fired magazine-type space heater (Booker heater) was operated without the furnace attachment at efficiencies to 75 pct. One test series was run with minimum supervision under conditions encountered in actual household operation. No mechanical trouble was encountered.

Jan 1, 1960

"INTRODUCTION These inspection standards have been prepared for use as a guide for the Federal inspection of anthracite mines. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7231 in January 1943 and used as a guide for Federal inspections. Numerous changes in the original standards have been made, due in part to recognition of shortages of some types of safety equipment due to the war, in part to need of additional standards to cover certain mine conditions and practices, and in part to conditions not foreseen when the original standards were prepared.Throughout these standards reference is made to determining the methane content of the mine air by using a permissible flame safety lamp. The Bureau has approved various electrical devices for the detection of methane, but it is recognized that new devices for determining the percentage of combustible gases as well as the percentage of oxygen, might be perfected for general use in mines, and therefore it may be necessary to revise certain standards to include the use of such equipment if and when the device is accepted as being permissible.About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however, failure to carry out the suggestions made in such of the other standards as are applicable may also lead to loss of life.With continuing change in mining methods, some of these standards may become inapplicable, and further revision will be advisable. Therefore, question regarding these standards and suggestions regarding new standards should be brought to the attention of the Bureau, so that changes may be made from time to time. Numerous changes proposed by mine operators and by State mining departments have been incorporated in these standards."

May 1, 1944

By W. H. Coghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

By W. A. Jacob, E. W. Dean

The Pittsburgh petroleum laboratory of the Bureau of lines has recently developed an improved method for the determination of water in pctroleum emulsions. It has been described in detail in an article entitled "A convenient method for the determination of water in petroloum and other organic emulsions" by E. W. Dean and D. D. Stark (Jour. Ind., and Enc. Chem. Vol. 12, ſay, 1920, page 436). It is essentially a modification of the familiar procedure of "distillation with an iniscible solvent", the improvement consisting in the use of apparatus that is rºck more convenient than any previously employed. The method has been used with marked success in the Bureau's laboratories for a period of about a year and has also been tried with equal satisfaction by a number of other laboratories. It has been most extensively employed for determining the water content of heavy fuel oils but has been applied also to several other types of emulsions, including shale oils, tars derived from coal, greases, and mixtures of powdered coal, oil and water. The Bureau has received a number of requests for information regarding commercial sources for the apparatus used, and having been assured of the value of the method, has taken steps to render it available for general use. - The equipment is, with the exception of two items, made of parts that are obtainable from the ordinary stock of chemical supply houses. The two exceptions are (1) the so-called "distilling tube receiver" and (2) the electric heater. The former is an essential part of the equipment; the latter is a convenient ac cessory but it can if necessary be roplaced by a gas burner. Efforts on the part of the Bureau staff to ronder these two items of apparatus available for purchase from supply houses, or for production by the user are hero described.

Sep 1, 1920

By William A. Hustrulid

A technical and economic evaluation of the potential for improving mining productivity through the use of underreamers in blastholes, specifically in relation to Minnesota taconite, Arizona surface copper and in situ mining operations is presented. Included are (1) a review of the drilling and blasting practices presently being used, (2) a discussion of current underreamer technology. (3) the presentation of a general economic cost model for underreaming, (4) the application of the model to surface taconite, surface copper and in situ mining, and (5) a summary discussion including required performance specifications, potential overall benefits, and recommendations for further development.

Jan 1, 1977

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

RECOMMENDATIONS FOR FURTHER WORK Based on the development effort and full-scale tests conducted during this program, a number of technical areas for future research and development have been identified. Further work in these areas would help to improve the reliability, speed of operation and efficiency of the remote sealing system. Recommendations for future work are summarized as follows 1. Development of an Inert Gas Generator For the sake of expediency in conducting the field test program, fresh air was used as the fluidizing medium for the fly ash. However, in an actual mine fire application the use of fresh air is likely to be prohibited. An inert gas, such as nitrogen, carbon dioxide or air containing less than 8 percent oxygen would be required. Using combustion as a means of reducing the oxygen content of air appears to be an attractive solution to the generation of the high flow rates of gas required (2500 to 5000 scfm). Such an inert gas generator would serve a dual purpose for the overall fire extinguishing operation. First, it would provide the inert gas for fluidizing the fly ash. Second, it could be used for inerting the fire area after the seals had been placed, thereby reducing the time required to extinguish the fire. It is recommended that the Bureau undertake a program to develop a field-operable, inert gas generator to satisfy these two requirements. 2. Development of a Field-Operable Sonar Initial Probing System A first stage prototype of a sonar initial probing system was developed during this present program. The results obtained with

Jan 1, 1973

To design an apparatus that advances the state of the art in gas content testing equipment. The goal of the design is to incorporate improvements in testing sensitivity/accuracy, durability, and ease of operation over existing equipment. It is also desirable for the new design to successfully perform gas content determinations of multiple chemical species from a rock sample.

Jan 1, 1999

By D. E. Van Dillen

Seven configurations for panel entries of a longwall coal mine are compared and ranked according to structural stability. These entry configurations are analyzed using three-dimensional finite element modeling The models include large dimensions to minimize boundary effects, elastoplastic constitutive relations, and simulated excavation and construction of support systems. The stability criteria are formulated in a quantitative manner to facilitate the ranking of the entry configurations. These criteria are based on the expected volume of caved rock in the entry openings. The stability ranking is applied to the entry excavation phase, the headgate phase, and the tailate phase of the entry life cycle. Parametric variations are applied using two-dimensional finite element models to determine the sensitivity to changes in mining and design parameters.

Jan 1, 1981

By Fred N. Kissell

This handbook describes effective methods for the control of mineral dusts in mines and tunnels. It assumes the reader is familiar with mining. The first chapter deals solely with dust control methods, regardless of the application. It is a brief tutorial on mining dust control and will be of help to the reader whose dust control problem does not conveniently fit any of the mining equipment niches described in later chapters. The subsequent chapters describe dust control methods for different kinds of mines and mining equipment. This includes underground coal and hard-rock mines, as well as surface mines, stone mines, and hard-rock tunnels. Because dust sampling has so many pitfalls, a chapter on methods used to sample dust is included. For those occasions when there is no practical engineering control, a chapter on respirators is also included. Except for those listed as ?future possibilities? in the longwall chapter, the dust control methods described are practical and cost-effective for most mine operators. If controlling dust were a simple matter, dust problems in tunnels and mines would have been eradicated years ago. Unfortunately, most underground dust control methods yield only 25% to 50% reductions in respirable-sized dust. Often, 25% to 50% reductions are not enough to achieve compliance with dust standards. Thus, mine operators must use several methods simultaneously, usually without knowing for sure how well any individual method is working. In fact, given a 25% error in dust sampling and day-to-day variations in dust generation of 50% or more, certainty about which control methods are most effective can be wanting. Nevertheless, over the years, some consensus has emerged on the best dust control practices. This handbook summarizes those practices.

Jan 1, 2003

By Jack E. Fraley

Because of their noncombustibility, silicate and magnesium oxycements are desirable for sealing shale in underground coal mines. In this Bureau of Mines investigation, cement samples were cured and tested (nonstandard tests) for submersion to note resistance to dissolution (breaking into parts), which is an important property for a coating. Nonappreciable dissolution during 1 week of submersion was set for passing the test. Over half of the coatings passed the test.

Jan 1, 1977

By J. M. Mutmansky, L. Xu

"IntroductionSince the establishment of the star,just concentration of 2 mg/m3, a strong effort has made by mining engineers and researchers to provide better dust control equipment and procedures for underground coal mines.Particular areas of success have been implementation of better coal-cutting strategy to control dust generation, better design of water sprays for dust suppression and air movement, use of scrubbers, and improved design of face ventilation systems. A drastic improvement occurred over time such that the average dust concentrations for continuous miner operators dropped from 6.5 mg/m3 in 1968 to 1.3 mg/m3 in 1980 and for auger, cutter, longwall, and roof bolter occupations from 2.7 mg/m3 in 1973 to 1.6 mg/m3 in 1980 (Niewiadomski, 1983).While dust concentrations in mining sections have been dropping considerably, one problem area has been mining sections where quartz is a considerable portion of the airborne dust. The federal regulations require that quartz content must be held below 0.1 mg/m3 in the air regardless of the concentration of the total dust. This legislation limits the allowable dust concentration to a ""reduced standard"" of 10/ (% quartz) when the quartz content of respirable dust in the mine atmosphere is more than 5%. Today, approximately one-third of underground coal mining operations have designated areas with more stringent dust standards in place, and many mines experience considerable difficulty in meeting these standards (Jankowski, and Babbitt, 1989).It is well known that metal miners subjected to respirable dusts high in quartz have a higher incidence of silicosis than those exposed to dust low in quartz. However, the role of quartz in the development of coal workers' pneumoconiosis is still a highly controversial question, in spite of the large number of research projects devoted to this subject over the last 20 years. Because coal seams contain less quartz than metal ores and quartz often comes from sources outside the coal seam (e.g., roof and floor), it is difficult to relate studies that deal with the quartz content in coal seams and the incidence of coal workers' pneumoconiosis. Hamilton, Ogden, and Vincent (1983) have provided a plausible explanation for the incidence of the disease by hypothesizing that the quartz content does not affect the probability of developing pneumoconiosis until some threshold value (generally thought to be about 10%) is exceeded.The objective of the research studies summarized here was to obtain a better understanding of quartz occurrences in airborne coal mine dust by studying the variations of the quartz levels in different dust sizes and the relationship between the quartz content in airborne coal mine dust and the quartz content in the mined material. The implications of the results to control of dust in high-quartz sections will also be discussed."

Mar 1, 1992

By Robert J. Timko

Because of leakage through and around permanent stoppings in underground mines, more air must be forced into a mine than would otherwise be required for ventilation. As power costs increase, costs resulting from air leakage add increasingly to the operating costs of mining. The Bureau of Mines evaluated four different stopping construction techniques based on the ideas that (1) airtightness could be enhanced by brushing rather than troweling on mortar sealant and that (2) modified mortars (mortars containing glass fibers and other additives for increased strength and adhesion) would improve sealing performance. Air leakage tests comparing conventional to modified stoppings were done when the stoppings were built, after 6 months, after 1 yr, and following simple maintenance. It was found that stoppings can be built and maintained better if-- The area where a stopping is to be built is properly prepared. Stoppings are constructed using the techniques devised by the Bureau. Stoppings are periodically examined for leaks. Stoppings found to be leaking, especially at the perimeters, are resealed.

Jan 1, 1983

By R. G. Burdick

The problems presented by old mine workings affect both present day mining and land development. An automated method of locating these old mines from the surface using electrical resistivity techniques was de-veloped earlier under a Bureau of Mines contract. Subsequent Bureau research has refined the techniques and expanded the area of study to a variety of geologic provinces. During this research, six mining areas in the United States were in-vestigated with the Bureau's automated resistivity method. This report describes the mining areas involved and the results of the resistivity investigations, which showed a high rate of success in detecting old mines. It also describes the field measurement techniques and data analysis procedures.

Jan 1, 1986

By H. H. Fields, Joseph Cervik, G. N. Aul

Coal is a soft and brittle material. Drilling rates in the Pittsburgh coalbed using a drag bit exceed 3 ft/min at 2,500-pound thrust. However, maintaining the bit on a horizontal trajectory or parallel to bedding planes to attain lengths of 1,000 feet is difficult. This Bureau of Mines report presents a drill string configuration that can be guided through the coalbed. The angle of the borehole is measured periodically and by proper combinations of bit thrust and rotational speed (r/min), bit trajectory can be lifted or dropped to keep the bit in the coalbed. An example of a hole drilled to 2,126 feet is presented to show levels of thrust and rotational speed used to lift or drop the bit, the seemingly unexplainable events that occur, and the strategy used during drilling. Thrust levels during drilling range from 600 to 2,500 pounds. Hydraulic motors powered by a 30-hp, 440-volt motor provide ample power for drilling horizontal holes 2,000 feet long.

Jan 1, 1975

By George D. Dub

The Bureau of Mines, in connection with the investigations of war minerals it conducted, examined the graphite deposits of this country, studied the methods of mining and preparation used, and sought to devise more efficient methods for the preparation of domestic graphite, and to standardize the quality of the product. The graphite investigations covered three general phases, as follows: 1. An examination of the deposits in Alabama and other States, and a survey of the methods of mining and preparation used. In this connection methods of sampling and analysis were noted and experiments made to determine a standard method of sampling and a, rapid but accurate method of analysis. 2. Experimental work on the concentration and refining of domestic crucible graphite to improve the quality of the product and to lessen waste. 3. Experimental work in crucible manufacture to determine the properties of domestic flake and the maximum proportions that might be used without impairing the quality of the crucibles. This work was accompanied by photomicrographic study of crucible structure.

Jan 1, 1920

By William C. Smith

Roof support, an important aspect of ground control, involves maintaining roof competency to ensure a safe and efficient mining environment. Wide variability in rock quality and stress distributions requires a systematic approach to roof support design that satisfies specific goals. The success of past roof sup-port in reducing the incidence of roof falls has been primarily attributed to safer roof bolting practices. However, roof falls continue to be the number one occupational hazard in underground coal mines. This U.S. Bureau of Mines report presents a general overview of roof bolting and other roof support methods used in the United States. Characteristics of bad roof and associated roof failure theories are briefly presented as background to roof support. Methods of detecting and monitoring roof behavior and/or bolt performance provide essential feedback on roof support requirements. A discussion follows on roof bolt design that assimilates roof and support parameters into useful equations or nomographs to help decide what bolt types to use and how they should be installed under different roof conditions.

Jan 1, 1993