Search Documents

By Lewis C. Karrick, Martin J. Gavin

"Introduction.The theory of fractional ""education"" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil from the oil shales of the United States. The term fractional ""education"" gives expression to the rather common belief that when an oil shales is heated it produces light, low-boiling oils as low temperatures, and increasingly heavier, higher-boiling oils as the temperature of retort¬ing rises. The theory evidently had its origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases is as, gasoline is produced from petroleum at relatively low temperatures, kerosene at higher temperature, and heavier products such as gas-oil and lubricating distillation at still higher temperatures.The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and in some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperat.res, and so on. Such retorts are usually designed to operate continuously and have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts repeat that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale passes to zones of increasingly higher temperatures, the vapor lines lending from these zones rill remove increasingly heavier products such as kerosene, gas-oil etc."

Mar 1, 1924

By T. L. Joseph

The size and accessibility of the Minnesota manganiferous iron ore deposits make them attractive as a potential source of ferromanganese, which is essential in the production of steel. For several years the Bureau of Mines has been conducting experiments to determine the feasibility of producing ferromanganese from these ores by a three-step process which involves (1) the smelting of the ores in the blast furnace to produce a high-phosphorus spiegel; (2) the treatment of the spiegel produced from step 1 in an electric or open-hearth furnace to separate the manganese from the phosphorus and the iron; and 3) the smelting of the high-manganese slag from step 2 to produce ferromanganese. The details of the first two steps of the process and the results of tests with the experimental furnaces have been given in previous reports.

Jan 1, 1931

By H. C. Carpenter

Lignite tar made by low-temperature Lurgi-Spülgas carbonization of North Dakota lignite was hydrocracked in single-pass, fixed-bed operation at 3,000 pounds per square inch over cobalt molybdate catalyst to produce gasoline, and at the same pressure, over zinc chromite catalyst to crack the high-boiling phenolic compounds to low-boiling phenolics. Hydrocracking the raw tar or the creosote-oil fraction from the tar over cobalt molybdate removed most of the oxygen, sulfur, and nitrogen in the forms of water, hydrogen sulfide, and ammonia, and produced gasoline yields from 31 to 59 volume-percent. The gasoline fractions contained from 0.1 to 7.7 volume-percent tar acids, but tar-base percentages were too low for reliable measurement; removal of these materials with dilute caustic and acid solutions also reduced the sulfur and nitrogen to 0.01 weight-percent or less.

Jan 1, 1963

By Maria I. De Rosa

The Bureau of Mines performed experiments to determine concentrations of toxic gases and liquids, and smoke-particle diameters and diameter-concentrations evolved during degradation of PVC-derived brattice with and without nylon-woven fabrics, fiberglass, cotton, and jute brattices, and other mine materials. The samples were exposed in a 20-L chamber at temperatures of 1500 to 4500 C, with a chamber airflow of 10 L/min; 27.3 cm3/s of which was directed into a submicrometer-particle detector-analyzer. During the degradation of PVC-derived brattice, large concentrations of hydrogen chloride (TLV, 5 ppm; STEL, 100 ppm) evolved at a temperature as low as 2000 C. The minimum toxic load of 3.1 mg or 40 ppm in 50 L of dilution air, with O.l~g weight loss, may be reached at a mine face with 314,000 L of dilution air, at the 5th min, during which less than 1 kg of brattice undergoes combustion. Fiberglass, cotton, and jute brattices, pine wood dust, and coal dust showed small concentrations of carbon monoxide evolving during early stages of combustion. Hydrogen cyanide gas evolved from the PVC-derived, nylon-reinforced brattice; at a later stage of combustion, large concentrations pf carbon monoxide and dense smoke evolved from all PVC-derived brattices. Experiments to characterize smoke particles showed that marked differences exist in particle diameter-concentrations among the materials.

Jan 1, 1986

By JOEL H. SWARTZ

During a series of resistivity measurements carried out in 1929 and 1930 a number of questions arose concerning the effect of topography on the character of the curves and the depths attained , the ratio of true depth to certain radii interpreted as representing depth , etc. To answer these questions it was decided to undertake a series of experimental investigations on artificial strata . It is the purpose of the present paper to present the results of the studies thus undertaken .

Feb 1, 1931

By S. H. Ash

The Pennsylvania anthracite-mining region is the only one in the world of major magnitude. As the deposits of anthracite in the United States are limited virt113.lly to Pennsylvania, the difficulties of this industry have been commonly considered a State rather than a national problem. However, there is also national interest in the conservation and wise utilization of all fuel resources and in the control of interstate waterways. The anthracite industry is confronted with the very se:;-ious :problem of accumu.lation of water in many of the mines. This problem must be solved soon if progressively higr-er mi~ing costs are to be avoided. The water proble~ cannot be solved by the operating compa,nies without State or Federal aid, or both, owing to the magnitude of the work requir~d, diversity of interests of the coal ana surfa.ce ovmerships, hazard to the whole mining community, and interests affec~ed outside the mining region. The cost of abati~ the ever-increasing_surface seepage to mine workings and of handling this seepage once it }3s occurred is beyond the economic resources of most ope~ating ma.'18.gements. The data in this paper giving the high lights of the water problem and indicating what appears to be a step in the right direction are based upon observations made during the past year that the industry desires and believes it is to the npublic interesttr to keep mine workings free of flood end surface waters.

May 1, 1941

By G. S. Rice, H. P. Greenwald, H. C. Howarth

"Stoppings in coal mines serve, important and. vital functions, such as coursing the ventilating current, sealing off abandoned or dangerous workings, sealing fire areas, and separating mines at boundaries. Stoppings may hold back water, but normally that is not their function; their design is, or should be very different from that of a hydraulic dap which is designed to a definite load, often a very heavy one, from one direction over an indefinitely long period. Hence, a dam usually requires an arched structure to resist hydraulic pressure, and it must be massive to meet vertical stresses due to heavy ground pressure.Stoppings are designed primarily to resist a pressure applied laterally through air or gases. Their strength cannot be stated without specifying the direction of applied load. A stopping may be placed in stress by proof pressure subsequent to erection, through extraction of pillars in the vicinity which may act direct, or by squeezing the ribs or heaving the floor. These forces act more or less parallel to the faces of the stopping and may be very great but measures must be taken suitable to each case, and it is impossible to allow for these in general specifications other than to call for normally good construction. A stopping is principally designed to resist the action of forces at right angles to its face, such as the shocks of blasting, the pressure of gas from instantaneous violent out bursts such as have occurred in certain British Columbia coal mines, sudden compression of the air by great falls of roof in closed spaces, and at time pressures that accompany an explosion of either fire damp or coal dust or both. This paper deals with the tests of pressures of explosions only."

Sep 1, 1930

By George A. Bell

This paper reviewing the leaching practice of the New Cornelia mines of the Calumet & Arizona Mining Co. at Ajo, Ariz., is the first of a series being prepared by the Bureau of Mines on leaching methods and costs in the various mining districts. ACKNOWLEDGMENTS The author acknowledges the assistance of T. G. Chapman, consulting engineer, and E. D. Gardner, supervising engineer of the Southwest Experiment Station, Bureau of Mines, Tucson, Ariz.

Jan 1, 1930

By Sara J. Davenport

Hydrogen sulfite has been listed (1)3/ as a possible hazard in 50 occupations, many of which are in the mineral industries. The effects of its occurrence in the petroleum industry made themselves felt more than two decades ago, resulting in a comprehensive study (2) of the toxic gases from Mexican and other high-sulfur petroleum products. The mining industry, likewise, has had cause to guard against this gas. Enough hydrogen sulfide has been found in coal and some noncoal mines during normal operations to cause severe eye irritation, some serious illness, end even fatalities. It is usually a product of the decomposition of sulfur compounds and may be produced by burning explosives containing sulfur; the gas in harmful qauntities is formed by the use of block blasting powder or by the use of dynamite in blasting sulfide ores. Hydrogen sulfide is readily soluble in water, and enough may be released from water streams in coal and noncoal mining to cause fatal poisoning it is found sometimes in stagnant water underground, particularly where ventilation currents are absent, and great care must be exercised when accumulations of such waters are disturbed, as exposure to comparatively low concentrations of the gas evolved therefrom has caused fatal accidents.

Jan 1, 1945

By Charles Vaught, Michael J. Brnich, Roberta A. Calhoun

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.2 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Underground coal miners Length: 9 questions (30 minutes for administration and 30 minutes for discussion) Skills: Mine fire escape strategies/procedures Use of emergency breathing apparatus Knowledge of sensations experienced when wearing breathing apparatus Communication Location: Underground coal mine section, average 60 inch seam height Problem: You are the section foreman on the 17 Left longwall development section at the Paula Ann No. 3 mine. The section has been driven about 4,000 feet from 4 West Mains. One of the shuttle car operators took a call from the fireboss saying that there was smoke from an unknown source coming into your section. You attempt to contact someone to find out where the smoke is coming from but get no response. You assemble the crew and start riding out of the section on the mantrip when you encounter heavy smoke. At this point, you decide to take your crew and travel on foot in the belt entry that is on a neutral split of air. After traveling about 6 crosscuts in the belt entry, you encounter heavy smoke at which time you and your crew don your person-wearable SCSRs (PWSCSR). After donning the apparatus, you and your crew continue traveling outby in the belt entry. Near the mouth of the section, one miner in the group starts to have trouble breathing from his SCSR. Because breathing resistance is increasing with the length of time the apparatus is worn, the miner is "outbreathing" the device since his oxygen requirements are greater that what the PWSCSR can supply. Although you slow

Jan 10, 1999

By D. A. Douglass

This report describes the tri-n-butyl phosphate extraction of cerium (IV) from a sulfate leach liquor prepared from a bastnaesite concentrate as well as from pure eerie nitrate solutions. The work was done on a laboratory scale using separatory funnels. Extraction from pure cerium solutions entailed no great difficulties; however, extraction from the bastnaesite solution proved more difficult, mainly because of the inhibiting effect of the sulfate ion. Despite this, procedures were developed for obtaining good single-state cerium extraction (95+ percent) and a high-purity product (99+ percent), although the maximization of both cannot be achieved simultaneously. This necessitates a compromise in any extraction scheme.

Jan 1, 1959

By A. W. Fahrenwald

The logic leading to the development of the experiments in this paper already has been stated in Part I,3 but is briefly as follows: The results of the batch-grind experiments in which time of "grind" and fineness of finished product were the variables, strongly indicated (1) that batch grinding involving a single grind could not be operated under any condition to give maximum mill efficiency, (2) that the, sieve analysis of the feed charge in the mill materially affected the efficiency of the mill, and (3) that the percentage of finished product in the mill is a vital factor in ball-mill efficiency. A laboratory closed-circuit grind technic designed to simulate present closed-circuit grinding suggested itself, in which: a ball mill and a classifier constitute the grinding unit. The features of the closed-circuit grinding system are: (1) Short large diameter mills, (3) rapid flow of pulp through the mill, (3) continuous automatic removal of finished product from the system, and (4) high circulating loads. The high circulating load is a result if the short length of the Mill - that is, of the time the charge remains in the mill - and the small percentage of finished material produced during each circuit of the feed through the mill.

Jan 1, 1930

By J. M. Mutmansky, C. Lee

"This paper outlines some of the work associated with a research study into the relationship between the characteristics of coal mine dust and the incidence of coal workers' pneumoconiosis (CWP). The project involves study of the chemical, mineralogical, and morphological characteristics of the dust. Early stages of the study have dealt primarily with the size analysis and elemental composition of airborne dust in continuous miner sections. This paper outlines the procedures and findings of the elemental analysis portion of the study.Most of the previous elemental analyses of coal were made available in the quest for information on the combustibility of coal dust or on causal agents and prevalence of CWP. However, no extensive studies have been performed to date, primarily due to the limitations of the analytical methods. A review of the analytical methods for elemental characterization of coal and coal dust particles is presented. TI1e comparisons are made based on the sample mass required, the sample preparation required, the destructivity of the test, and the capability of providing an easy multi-element analysis. The reasons for selecting the proton-induced x-ray emission spectroscopy (PIXE) method are outlined.The PIXE method was applied to both the airborne coal mine dust and channel samples collected from seven continuous miner sections in six different mines. Channel samples of the coal, roof and floor were collected and analyzed. Airborne dust sampling was performed using multi-stage cascade impactors and permissible 2.0 I/min pumps. Sampler locations were fixed in the sections with respect to the continuous miner and roof bolter or with respect to the intake and return airways. Sampling times varied from 45 minutes to 6 hours, depending on the dust concentration.The statistical analysis of the resulting elemental data is presented. Of particular importance are the analyses of the variation of elemental composition with size and the variation in elemental composition over the working section. One interesting finding is outlined showing the multivariate statistical analysis of the trace elements and its implications in the identification of the dust sources. The paper concludes with an analysis of the ramifications of the elemental data to related medical studies."

Mar 1, 1989

By John L. Nieber

This information circular describes a computer program called VARSAT2D, a comprehensive unsaturated fluid flow simulator developed by the U.S. Bureau of Mines. VARSAT2D solves for either a vertical or horizontal, transient or steady-state solution in variably saturated, heterogeneous, anisotropic porous media using the Galerkin finite-element approach. Simplex triangular elements are used. Moisture retention characteristics are described by specifying either the Brooks and Corey, Brutsaert, or Van Genuchten power functions, with hysteresis described using the Maulem independent domain model. Boundary conditions may include any combination of time-varying seepage, pressure along solution domain, boundaries and/or at internal node points, unit hydraulic gradient at the lower boundary, and a uniform source and/or sink. This program should be a welcome addition for mining and environmental hydrologists, researchers, and engineers interested in modeling unsaturated fluid flow.

Jan 1, 1994

By Arne Landsberg

A study of the chlorination kinetics of germanium, silicon, iron, tungsten, molybdenum, columbium, and tantalum has been made to determine the effects of temperature, chlorine concentration, geometric surface area and gamma radiation. The reaction products were volatile at the temperatures used this making it possible to follow the reaction rates by weight loss of the solid. Chlorination rates of germanium, silicon, and iron were found to be directly proportional to chlorine concentration while the rates for tungsten, molybdenum, columbium, and tantalum were proportional to the 0.5 to 0.6 power of chlorine concentration. A good correlation of reaction rate and geometric surface areas was not obtained because the true surface area of the samples could not be measured. Intense gamma radiation had no effect on reaction rates. The Arrhenius activation energies determined over the temperatures used are as follows: Germanium, 27 kcal/mole (233°-241° C); silicon 33 kcaL/mole (375°-517° C); iron, cold rolled, 20 kcal/mGle (259°-325° C) annealed, 21 kcal/mole (293°-337° C); tungsten, 43 kcal/mole (617-776° C); molybdenum, 37 kcal/mole (445°-4910 C); columbium) 34 kcal/mole (229°?255° C); and tantalum, 29 kcal/mole (370°-449° C).

Jan 1, 1965

By George E. Fasching

The Bureau of Mines has developed a pulse counting system with improved energy resolution and having dual channels to process pulses at different rates and a pulse pileup detector for channel selection. Pulse input is delayed until the detector determines if any pulse is so closely followed by a second pulse as to constitute pulse pileup. If no pulse pileup is detected, the slower channel is selected; this clips the pulse to a wide pulse width to retain good energy resolution. If pulse pileup is predicted, the fast channel, with correspondingly shorter pulse width, is selected to improve resolution with respect to time. Output of the two channels is transmitted to a pulse height analyzer for interpretation. The pulse processing system can process count rates above 300,000 counts per second with little loss in energy resolution.

Jan 1, 1974

By A. E. Back

[Several processes for recovering manganese from low-grade ores have been proposed3/4/5/ in which an aqueous slurry of the ore is leached with gas containing nitrogen, oxygen, and sulfur dioxide as obtained from burning sulfur or roasting sulfide ores. The manganese dioxide is dissolved, and most of the sulfur dioxide is oxidized to sulfate, but an appreciable quantity of dithionate is usually formed, together with acid from oxidation of the sulfur dioxide. The over-all reactions may be represented as follows: (1) Mn02 + S02 = Mn++ + S04--. (2) Mn02 + 2S02 = Mn++ +S206--. (3) H20 + So2 + 1/2 02 = 2H+ 5S4--. (4) H20 + 2S02 + 1/2 02 = 2H+ + S206---.]

Jan 1, 1952

By Frederick C. Trutt, Jeffery L. Kohler, Joseph Sottile

Condition-based maintenance (CBM) of industrial equipment is generally recognized as being the most cost-effective means for improving equipment availability. However, prerequisite to successful implementation of CBM is a reliable detector of failing components. One such detector, termed the effective negative-sequence impedance, had previously been identified as an indicator of induction motor stator winding degradation. However, a limitation of this detector is that it does not change in a predicable manner under certain motor operating conditions. This paper presents an experimental investigation of an improved technique for on-line detection of induction motor stator winding degradation. The paper begins with a brief description of the detectors, followed by a detailed description of the experimental setup, the experiments conducted, and results.

By Duvall Wilbur I.

This is the second report to be presented on th application of stress analysis to underground Mining problems. In part I2/ of this investigation the stress distribution around single openings in unidirectional and hydrostatic stress fields was analyzed. Relationships between maximum stress concentration and size and shape of openings were determined by the photoelastic method. In most cases the results were verified by mathematical methods This report considers the stress distribution in pillars formed by two or more openings in a. unidirectional stress field. Relationships between stress concentrations and size and shape of pillars are developed. Applied to mining, results snow how estimates may be made of the stress distribution in pillars, what factors cause high local stresses, and how local stress concentrations may be reduced by proper design of mine openings. The photoelastic method was used, as in Part I, to study the stress distributions, and, whenever possible, the results were verified mathematically. A description of the photoelastic method and equipment is .given in Part I.

Jan 1, 1948

By R. R. Sayers

The contemplated use of dichloro-difluorco methane in domestic and commercial refrigerating appliances and in air-conditioning equipment for public buildings and possibly homes, brims attention to the health hazards involved in a wide potential exposure of the public to vapors of another new product, and for the first time to vapors of an organic fluorino compound. The objective in the development of this new refrigerant, however, has been the mitigation of health and explosion hazards in automatic refrigeration, and accordingly these factors have been given primary attention. Early in the development, the Bureau of Mines as requested to make a laboratory study of the toxicity and potential hazard, and it was ca the oasis of the results is of this work and the results of a preliminary investigation made in another laboratory6 that the compound has been selected for commercial use. The investigation conducted by the Bureau of Mines is still in progress, enough information has been obtained to indicate the order of the toxicity and the magnitude of the health hazards involved in the use of dichloro-difluoro methane as a refrigerant. The following is a summarized report of the work completed to date:

Jan 1, 1930