Search Documents

By D. E. Pollock, J. A. Organiscak

Water sprays and water powered scrubbers have both been utilized in the mining and milling industry to suppress airborne dust. Unconfined water sprays operated at lower water pressures of ?689 kPa (?100 psig) can be very effective at wetting the mine product at the dust source and significantly reducing the amount of respirable dust that becomes airborne. However, unconfined waters sprays can be somewhat ineffective in actually removing airborne dust from the air. On the other hand, water powered scrubbers operating at higher water pressures of ?1,724 kPa (?250 psig) in physical enclosures or ducts have previously been demonstrated to be very effective in removing airborne dust from the air. These higher operating water pressures are uncommon in many mines and mills, so their use is limited. The National Institute for Occupational Safety and Health (NIOSH) recently investigated the performance of a lower-pressure, water powered inline series spray scrubber for removing localized airborne dust emitted at the source. Results showed noticeable improvements in airborne dust capture efficiency through the operation o f multiple inline series hollow cone spray nozzles within a round duct or pipe at the same water pressure as a single spray. Operating hollow cone spray(s) at higher water pressures noticeably improved airflow through the scrubber and yielded some additional scrubber efficiency improvements. Thus, in-line spray scrubber efficiency trade-offs were observed to be made by altering spray power components of water pressure and/or quantity (number of sprays). Results show that, on average, up to 0.23 and 0.32 m3/s (484 and 679 cu ft per min) of airflow at 0.81 and 0.69 dust capture efficiencies can be achieved with three 81° and 33°hollow cone inline series sprays, respectively, operating at 1,655 kPa (240 psig).

By Michael P. Hardy

The report described improvements and applications of the Hybrid Computer facility. Improvements implemented under U.S.B.M. Contract H0252035 included expansion of the capability to model nonlinear seam behavior, installation of a color video output display monitor, and further development of software capabilities. To demonstrate the capability of the system, firstly, the influence of nonlinear seam behavior response to the occurrence of coal mine bumps was fully investigated and secondly, the effect of improper mining sequence on bump occurrence was demonstrated. In addition, the system was applied to the analysis of a series of practical coal mine problems. Mines in three coal seams were analysed to investigate the parameters which contribute to the occurrence of coal mine bumps.

Jan 1, 1977

By Jr. Koch

Statistical methods applied at the Bureau of Mines Denver Mining Research Center to data from metallic ore bodies were used to evaluate lignite reserves from core data and to predict the extent of lignite horizons in some Texas lignite beds. Six lignite seam units were studied using data from 361 drill holes. The data indicate a total of 214.2 million tons of lignite in the area examined, and probable reserves of 113 million tons in an area 2,000 feet beyond the limits established by the drill holes. It was demonstrated that lignite reserves present in lenticular beds could be reliably determined by statistical techniques, and that core drilling could be optimized to maximum information with minimum drill holes. The technique described is applicable to other coal beds.

Jan 1, 1966

By Thomas M. Barczak

The success of longwall mining can largely be traced to the development of powered roof support systems. The most significant improvement in powered support design has been the shield support, which improved kinematic stability and promoted the application of longwall mining in difficult-to- control caving conditions where chock and frame supports were inadequate. The most obvious trend in shield design has been an increase in shield size and capacity. This U.S. Bureau of Mines report examines shield design and operation practices and their consequences for the utilization of high-capacity shield support systems. An optimization goal is to minimize support loading by selecting an active shield setting force that is compatible with strata behavior and shield loading characteristics. Shield stiffness is an important design parameter that is often overlooked. A consequence of increasing shield capacity by incorporating larger diameter leg cylinders is a proportional increase in shield stiffness. Setting forces have also increased in direct proportion to the increase in shield capacity. The increased stiffness and higher setting force cause the available capacity to be consumed more quickly, severely limiting the ability of high-capacity supports to last longer and provide reserve capacity for difficult mining conditions.

Jan 1, 1992

Improve the safety and comfort of operators of large mining equipment. Approach Develop an improved driver restraint system that is easy to use, reliable, and cost-effective, while providing increased protection in the event of a collision or rollover. The Novel Restraint System There are several problems associated with conventional lap-belt type restraint systems. Among these are: restriction of movement, lack of comfort, and fear of entrapment. Standard seatbelts become dirty and oily from lying on the vehicle cab floor and can ruin a driver's clothes. Some haulage equipment may not even have seatbelts available to drivers since they are sometimes removed during maintenance activities or as a result of vandalism. Recognizing a need to address such problems by providing a more acceptable means of driver restraint, the Bureau of Mines designed and fabricated a novel vest-type restraint system. The vest is designed to be worn during a driver's 8-hour shift and would be issued much like safety glasses, hard hats and safety shoes, thus becoming part of the operator's individual protective equipment and assuring that each vehicle has a restraint system when in operation. The vest-

Jan 1, 1985

By M. A. Schellhardt

The Bureau of Mines has made periodic back-pressure tests on numerous gas wells in the Texas Panhandle field luring the past several years to study the delivery capacities of the wells under different pressure and operating conditions and to determine the relationships between pressures and rates of delivery from gas wells.4/ However, information regarding the intake capacities of gas-well systems is meager, end in projects involving- the flow of gas into porous-rock reservoirs it has been necessary to determine intake capacities of gas wells by trial. Accordingly the fundamental intake characteristics of natural-gas wells have been studied to develop a method for determining intake capacities under different wellhead pressures from data descriptive of the "output" or producing characteristic of the wells.

Jan 1, 1936

By A. J. Farstad

Electromagnetic location tests were conducted by Westinghouse Georesearch Laboratory under the sponsorship of the U. S. Bureau of Mines at the Galena Mine in Northwest Idaho. The objectives of these tests were to evaluate the performance in deep hardrock mines of an electromagnetic location system previously developed for the U. S. Bureau of Mines for use in coal mines. Tests were performed using long wire transmitting antennas as well as horizontal and vertical transmitting loops at depths from 3000 feet to 4300 feet (995 metres to 1311 metres). Surface measurements were made of magnetic field strengths, field strength patterns, and background noise, These measurements were compared with theoretical predictions for a homogeneous ground conductivity consistent with this particular geologic region. The results of the Galena Mine tests show conclusively that light-weight portable electromagnetic transmitters can be effectively utilized to provide uplink communications and location information in deep hardrock mines. Typical metal mines such as Galena utilize deep vertical shafts for mine access and haulage and these shafts produce signal enhancement at the surface from underground electromagnetic transmitters by as much as 30 dB. The results also show that horizontal wire configuration can serve as an effective alternative to the magnetic dipole antenna as a rescue transmitting antennaa and can be used when the required area is not available for deployment of a loop antenna. In spite of the electromagnetic coupling effects observed in the vicinity of the shafts, the location accuracy obtained still provided useful information on the general location of the transmitting sources involved. The horizontal wire location accuracy was within 46 metres, while the vertical magnetic dipole and the horizontal magnetic dipole accuracies were within 152 metres and 110 metres respectively at a 915 metre depth.

Jan 1, 1973

By Robert A. Speirer, Richard G. Burdick

Methods of detecting geologic faults and other linear features by means of processed LANDSAT satellite images have gained prominence during the past several years . There have been numerous programs written to pick these " lineaments , " but they have been almost universally tailored to large computers . This Bureau of Mines report describes a detection method developed for use with a minicomputer . The method comprises a suite of programs that scans an image for all " potential " lineaments . From this partially analyzed data , the final lineaments are picked by another routine . The method was field tested in an area of south- central Wyoming , and results indicated good agreement between computer- picked lineaments and ground features . Most of the known geologic faults in the area were picked by the method . Such features as roads and trails were also picked but were easily distinguished from faults during field inspection . The method is relatively new but promises to be a viable reconnaissance technique for the mining industry in geologic structural analysis .

Jan 1, 1965

By Douglas Milne

Most empirical and numerical approaches to design in rock mechanics incorporate rock mass classification. Numerical design methods generally use classification values to calculate input parameters for stress-based failure criteria. Empirical methods use classification to allow comparisons between similar rock mass conditions, generally based on a graphical design technique that differentiates stable and failed opening geometries. Classification systems are the best tool available for assessing rock mass properties; however, there are problems with classification systems that should be high-lighted. Rock mass performance can only be realistically estimated by coupling a unique description of the rock mass with known loading conditions. Current classification systems cannot provide a unique classification value. The weightings applied to quantify rock mass properties for classification can result in significantly different rock masses having the same classification values. These weightings have been proven effective for tunnel design and support, but classification systems are now used for many more applications. Rock classification systems evolved from a quick and easy field tool for estimating tunnel stability and support requirements. The need for a rapid field tool means that rock mass classification is relatively insensitive to improved methods of measuring rock mass properties. Problems with classification systems and their application are highlighted in this paper. These problems must be recognized and documented before improvements can be made. An understanding of the evolution of classification systems and their application for both numerical and empirical design approaches is invaluable in highlighting current shortcomings.

Jan 5, 2007

By Walter G. Dupree

When the original version of this study was published in 1972 it was evident that a problem was developing on the energy scene. The ability of the United States to find the energy supplies it needed within its own boundaries--at least in the forms desired--was declining. Production of crude oil in the United States had peaked in 1970 and was declining slowly; environmental restrictions had begun to hamper the production and consumption of high sulfur coal; natural gas reserves were beginning to dwindle; and the development of nuclear power was proceeding more slowly than originally planned. Shortfalls in energy supply were being met through the importation of increasingly larger quantities of petroleum, but supplies were adequate and the price of the imports was below that of domestic production. The energy problem was more prospective than current. In October of 1973 the prospective problem became the "Energy Crisis' when the Arab petroleum exporting countries reduced crude oil production, imposed an embargo on the shipment of crude oil to the United States, and then raised the price of crude oil in a series of large steps. This crisis was a clear demonstration of the dangers of the dependence of the United States on imported petroleum, and of the Nation's vulnerability to the actions of the oil exporting countries. After the embargo was lifted, attention shifted to the immediate hardships resulting from the higher prices for gasoline, fuel, and electricity,

Jan 1, 1975

By Jr. Reed

Cassiterite was discovered in Coosa County, Ala. in 1880 by Judge John S. Bentley. Since that time intensive surface prospecting has revealed the presence of cassiterite in pegmatite bodies that occur in a zone about 20 miles long and 3 miles wide. Numerous trenches and test pits and several shafts were sunk, and one attempt was made to nine and concentrate the cassiterite commercially. The problem of a domestic tin industry and the question of the extent of the Alabama tin deposits have long been of public interest and concern. The deposits have been examined by numerous geologists and several governmental agencies, including the Geological Survey of Alabama, the Geological Survey and the Bureau of, Mines. of the Department of Interior, and others. The Bureau of Mines and the owners of the properties, Charles A. Dean and Robert A. Russell, investigated the Coosa County tin deposits under a cooperative agreement from October 1, 1948, to June 10, 1949. Sixteen hand trenches totaling 527 linear feet and 33 machine trenches totaling 6,780 linear feet were dug. Two shafts wore sunk for a total of 72 feet, and 44.4 feet of drifting was done. Thirty-one diamond-drill holes totaling 2,776 feet were drilled.. Four hundred thirty samples, representing 1,192.6 linear feet, were taken for assay and wore analyzed by the Southern Experiment Station at Tuscaloosa, Ala.

Jan 1, 1950

By R. H. Grau

Researchers from the National Institute for Occupational Safety and Health have demonstrated that mine-wide ventilation in large-opening stone mines can be improved by using low-pressure, high-volume propeller fans and constructing stoppings in key locations to direct and control airflow. In light of these findings, a comparative study was conducted to determine if a portable diesel-powered propeller fan could per-form more efficiently for dust dilution and transport than an axial vane fan for localized ventilation. The objective of this study is to evaluate both fan types for ventilation efficiency at an underground dump/crusher facility in a limestone mine. Results showed an improvement with the propeller fan to dilute both the respirable dust and the respirable silica dust around the dump/crusher facility. Overall, an average reduction of 20% in respirable dust and silica was observed at the dump/crusher location with the propeller fan.

By Harold M. Smith

This publication summarizes the literature on the composition of petroleum, with special emphasis on naphtha and gas oil, and provides a source book for the known qualitative and quantitative facts on crude oil composition. The discussion points out the known facts from supposition, and suggests new researches needed in various areas.

Jan 1, 1968

By D. Harrington, C. W. Owings

The mining industry is gradually realizing that safety education and safety inspection are economic factors that may not be overlooked as a means of reducing operating costs . Many mine operators , however , have failed to realize the benefits of safety , and the efforts of the more progressive mining companies are offset by the carelessness of neighboring companies when the accident records of a community or a State or the nation as a whole are considered . This tendency is indicated by the data collected by the safety division of the United States Bureau of Mines . During the fiscal year ended June 30, 1930 , relatively definite information: was secureä concerning 34 mine explosions , 24 mine fires , and 29 miscellaneous accidents ; these accidents are by no means all of the explosions , fires , and miscellaneous accidents which occurred in the mines of the United States during the period; but the data on the fires and explosions constitute a record of all of those types of accidents that were called specifically to the attention of the safety division , and the miscellaneous accidents include those on which definite , detailed data were obtained by the safety division .

Jan 1, 1931

By P. A. Lawless

The objective of the research performed A for the Bureau of Mines on this contract was to develop a portable instrument for the detection of carbon monoxide (CO) in a mine environment. The desired characteristics were sensitivity and specificity for CO with a stable calibration. The sensor of the instrument was to be of metal oxide composition, requiring low power for compatibility with the types of batteries presently used in personal equipment in mines. The solid state design was also desired for ruggedness and small size. A key design feature of the instrument was to be provided by adherence to the intrinsic safety design requirements for electrical equipments operated in potentially exposive mine atmosphere. The Research Triangle Institute has prior experience in developing a solid state oxygen sensor using a thin film of zinc-oxide (Ref. 1) and experience in fabricating thin film devices. Solid state sensors utilized by other workers (Refs. 2, 3, 4, 5, 6) have included metal and semiconductor films and crystals of materials like carbon and aluminum oxide for the measurement of water vapor in the air and have relied upon measuring resistance and capacitance changes in the sensor in response to adsorbed vapors or gases. Since the effect of carbon monoxide in changing the resistance of various materials such as molybdenum, platinum, and zinc oxide had been reported (Refs. 7, 8, 9, 10), the requirements appeared to be realisable, although it was recognized even at the inception of the work that specificity to carbon monoxide might require the incorporation of more than one sensor.

Jan 1, 1976

By L. A. Readdy

Pilot Hole "X" was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. The history of the drilling of Pilot Hole "XI' is presented. This historical summary provides the details of method used during the drilling of this hole. Problems encountered during drilling are discussed. The quantities of drilling mud and other materials used to drill the hole are documented.

Jan 1, 1977

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944

By L. C. IlsLey, H. H. Clark

In various publications relating to safety in mining the Bureau of Mines has called attention to the hazards attending the use of openBame lamps. An open-flame lamp is a potential source of danger in any coal mine. It may start a fire in a dry mine or an explosion in a gaseous mine. The type of open-flame oil lamp now used in mines is the product of long evolution; its principal merit is simplicity. That such a light is unsafe in an atmosphere containing gas (methane) is evident, and Sir Humphrey Davy immeasurably increased safety in coal mines when he found means of protecting a lamp flame so that it would not readily ignite gas. The safety lamp, however, gives less light than the open-flame lamp, is not as simple in construction, is more cumbersome, and must De carried in the hand .. Consequently, some miners are reluctant to abandon the open-flame lamp for the safety lamp, and risk their own lives and the lives of their fellow workers with the one rather than to be hampered by the other. When small electric bulbs, with their clear, white light, and small electric storage batteries became available, the advantage of combining these elements for a miner's lamp seemed manifest. The combination looked simple and safe, but was soon found to have elements of danger and weakness peculiar to itself. The Bureau of Mines showed, in 1911, that the breaking of a miniature electric bulb in an inflammable mixture of gas and air might ignite the mixture, so that only the fragile glass of the lamp bulb might stand between the miner and injury or death. There Was also a possibility that sparks from the small battery would ignite gas, and the accidental spilling of the contents of a battery on the miner's clothing or skin was a possible source of injury. The first portable electric miner's lamps that were carried in the hand, or with the battery strapped to the back and the light carried on the head, were exceedingly crude and were designed without appreciation of the sources of danger. The possibility, however, of producing a safe and practical miner's lamp by the proper combination and design of the elements available promised to increase safety so greatly that the Bureau of Mines attemr>ted to stimulate better design and construction by careful investigations and the establishment of an approval system that would be an assurance to the miner and an advantage to the maker of the lamp. As a result various manufacturers submitted types of lamps, cords, and bulbs for test and cooperated with the bureau in efforts to so improve the safety features of these devices that the lamps would P&$ specific tests for approval.

Jan 1, 1917

By Dupuy. Leon W., R. T. C. Rasmussen, W. A. Calhoun

"INTRODUCTION For many years it has been known that low-grade manganese deposits occur in the bluffs along the Missouri River Valley. Frequent attempts have been made to develop the ore and to produce a marketalble commodity but they have had little success. Under pressure of the war emergency and the shortage of manganese, the attention of the Federal Bureau of Mines was directedtoward the deposits.Manganese-bearing shale occurs from a point near Pierre, S. Dak., down the river to the Rosebud bridge near the Nebraska line (1).5/ The Bureau of,confined its work to the more accessible central portion of the deposits near Chamberlain, S. Dak. The ore occurs principally as concretionary nodules in the form of iron and manganese carbonates (manganosiarite and perhaps some manganocalcite; rhodochrosite has not been identified). At the surface the carbonate is often broken down so that the oxide of manganese gives the nodules a black The matrix or host rock is generally known as Pierre shale, composed of ""interbedded layers of bentonite, an altered volcanic ash, and dissemi¬nated bentonite particles,"" (2) and montmorillonite-beidellite clay minerals (3). The shale weathers to the very sticky gumbo characteristic of South Dakota and well-known to hunters and travelers in the area.The area selected for the experimental mining and pilot-plant work discussed in this report lies about 8 miles westerly from Chamberlain and is a few hundred feet north of U. S. Highway,16, on land owned or controlled,by M. Q. Sharpe of Kennebec, S. Dak., and the General Manganese Corp."

Feb 1, 1946

By Lee M. Manna

This report summarizes the program to design, fabricate, install and preliminary test a pneumatic braking system for 10-ton mine haulage cars. Major arrangement drawings are reproduced, pneumatic schematics, parts list and actual developed costs. Recommendations as to system improvements are made.

Jan 1, 1977