Search Documents

By J. W. van der Merwe, A. Palazzo

"Owing to the corrosiveness of the untreated brackish cooling water typically used for steel mills (and other environments), it is important to treat the water and monitor corrosion in such systems. Generally, corrosion rates are monitored with corrosion probes inserted into a pipeline or vessel. This has been standard practice for many years, and is widely accepted in industry. Typically, two kinds of probes are used - electrical resistance and linear polarization resistance (LPR) probes.In this study, the effectiveness and accuracy of the LPR technique was evaluated by comparing the electrochemical measurements with the results of mass loss tests using corrosion coupons. The corrosivity of the environment, a synthetic brackish water, was varied by varying the calcium hardness and alkalinity, and to simulate actual plant conditions temperatures of 35°C and 45°C were used. In addition to the corrosion rate measurements, the iron concentration was measured, as well as the imbalance from the probe.The corrosion rates obtained by LPR were from 57% lower to 385%higher than those from the immersion tests. Most probe measurements were higher than the immersion results, and 50% of the probe results were50% or more higher than the immersion results. The best correspondence between the two methods was obtained at low calcium levels, except for one measurement that was 93% higher than the coupon results. There was no clear correlation between parameters such as temperature and total alkalinity and the difference between the results. It would therefore appear that LPR measurements can differ significantly from immersion results, and LPR results should therefore be used with caution in industrial applications."

Jan 1, 2015

By R. Castro, R. Gómez, F. Betancourt, M. Moncada

In block cave mining, rock fragmentation is a key parameter that influences the production level design and mine planning. Fragmentation occurs mainly by natural breakage during the caving process and in the draw column. The breakage that occurs within the column is known as secondary fragmentation. Secondary fragmentation has been successfully described using the block caving comminution model, which replicates the fragmentation mechanics between particles under drawn and vertical loads in a draw column. This model is based on a kinetic and population balance approach, in which non-normalized and normalized assumptions can be used depending on material and comminution system behaviour. In this paper, the non-normalized and normalized approaches are applied and compared to laboratory data to determine which assumption should be used for secondary breakage in block caving. Approaches are compared graphically, with the mean square error and the Fisher test with a false-rejection probability of 0.05. Based on a statistical analysis, the results show that the normalized model can be applied to all the rock types tested.

Nov 1, 2021

By L. Forbes, G. Forbes, J. Wang

Bubble size measurement is a vital part of flotation system analysis and diagnostics. Over the years, a great many different bubble size analysis tools have been developed. However, all of them rely on ex-situ measurement and in-pulp sampling techniques. This paper evaluates the Mettler Toledo ParticleView™ Measurement probe as a novel method for in-situ bubble size measurement. This device is then compared to the conventional Anglo Platinum Bubble Sizer (StoneThree). It was found that the in-situ bubble size analysis technology appears to be a more user-friendly and reliable option for determining bubble size in flotation. However, the current instrument design is not suited to industrial applications. Keywords: Bubble size measurement, bubble coalescence, PVM probe

Jan 1, 2020

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By H. M. Stewart, N. F. Dawson, J. P. Beukes, P. G. van Zyl, Q. P. Campbell, A. Jordaan, R. I. Glastonbury, L. N. Sadiki

"SynopsisThe physical properties of oxidative sintered pellets produced from typical South African UG2 ore are compared with the physical properties of pellets produced with conventional South African metallurgical-grade chromite ore (from the Lower Group 6 or the Middle Group 1 and 2 seams). A statistical evaluation of the cured (sintered) compressive strengths proved that pellets prepared from UG2 ore are likely to have the same, or better, compressive strength than pellets prepared from metallurgical-grade chromite ore. The cured abrasion strength of the UG2 pellets was also superior to that of the metallurgical-grade pellets. Scanning electron microscopy (SEM) backscatter, secondary electron, and elemental X-ray mapping were used to determine the reasons for the general superior strength of the UG2 pellets. The case study UG2 ore also required 13 kWh/t less energy for milling to attain the required particle size distribution prior to pelletization, which can lead to substantial cost savings. Results presented in this paper can be utilized by ferrochromium (FeCr) producers to better quantify the advantages and disadvantages associated with the use of UG2 ore for FeCr production.IntroductionChromite, a mineral of the spinel group, is the only commercially viable source of virgin chromium units. Geologically, commercial chromite deposits in the world are found in three forms, i.e. alluvial-, podiform-, and stratiform-type deposits (Murthy et al., 2011; Cramer et al., 2004). Alluvial deposits were formed by weathering of chromite-bearing rock with the subsequent release of chromite and gravity concentration by flowing water. However, these deposits are relatively small and of comparatively minor commercial interest. Podiform-type chromite deposits usually occur as irregularly shaped pods or lenses, and their distribution within a mineralized zone is usually relatively erratic and unpredictable, making the exploration of these deposits difficult and costly (Cramer et al., 2004). Stratiform-type chromite deposits occur as parallel seams in large, layered igneous rock complexes with more regular layering and lateral continuity (Cramer et al., 2004). The largest example of a stratiformtype chromite deposit is the Bushveld Complex (BC) in South Africa, which holds an estimated three-quarters of the world’s viable chromite ore resources (Cramer et al., 2004).Several chromite seams exist in the BC. The seams of economic interest are the Lower Group 6 (LG6), the Middle Group 1 and 2 (MG1 and 2), and the Upper Group 2 (UG2) seams (Cramer et al., 2004). The LG and MG seams are specifically exploited for their chromium content, while the UG2 seam is mined primarily as a source of platinum group minerals (PGMs) (Xiao and Laplante 2004). Extraction of the PGMs from the UG2 ore usually involves the liberation of the sulphide by milling and subsequent recovery of the PGM concentrate through flotation (Xiao and Laplante, 2004). Chromite in the PGM concentrate is undesirable; therefore, PGM recovery circuits are specifically designed to ensure maximum rejection of the chromite to the tailings stream. However, the chromite in the PGM tailings can potentially serve as feedstock for ferrochrome (FeCr) production, after beneficiation to increase the chromium content."

Jan 1, 2015

By S. A. Ghoreishi-Madiseh, F. P. Hassani, H. Rafezi, H. R. Manouchehri, A. Shadic, A. P. Sasmito

Weakening rocks by taking advantage of microwave-induced microcracks is a promising solution for comminution processes. This paper investigates the effects of microwave treatment of the rock/or samples in single and multi-mode cavities. Based on the experimental results of using a 2.45 GHz microwave generator, the performance of different cavity setups and their impact on the energy effectiveness of the microwave irradiation was examined. Physical interpretations were drawn from multiple experiments with a relatively wide range of power rates and exposure times. Both basalt and kimberlite samples were used in experiments, and their results were systematically compared. For single-mode cavity tests, a microwave applicator waveguide antenna was placed at different distances from the samples to evaluate the effects of sample positioning on microwave heating, both numerically and experimentally. Eventually, cavity performance was assessed by using calorimetric test results, and strength decay was documented based on the spallation of the samples. It was found that the singlemode cavity setup has unique properties that can significantly improve the electromagnetic heating and therefore, strength degradation process. Keywords: Microwave, fragmentation, energy effectiveness, calorimetry, mine-to-mill

Jan 1, 2020

By H. Uygucgil, C. Kwang

The use of remote sensing and geographic information system techniques in mineral exploration is still underutilised. There is a need to explore the potential of new robust remote sensing and geographic information system techniques in the field of mineral exploration. In this study, we mapped the argillic alteration associated with epithermal gold-silver mineralisation. A band ratio of band5/band6 and Crósta technique on Advanced Spaceborne Thermal Emission and Reflection Radiometer within the Google Earth Engine Environment was applied. The bands 5 and 6 were selected for the band ratio after critically analysing and comparing the illite spectral extracted from the Advanced Spaceborne Thermal Emission and Reflection Radiometer image and the illite spectral obtained from the United States Geological Survey spectral library. The band ratio and Crósta technique identified and mapped the Ovacik goldmine and other argillic alteration zones. Even though both methods mapped out the argillic alteration zones associated with gold-silver mineralisation, the Crósta technique produced the optimal argillic alteration. The study demonstrates the analytical capabilities of Google Earth Engine in image processing and analysis for mineral exploration, such as discovering hydrothermal alteration associated with mineralisation.

Jul 23, 2025

By J. van Deventer

Testwork was done with two different adsorbents, Dowex-Minix gold-selective resin and activated carbon, to detemine their relative performances with regard to gold recovery from clarified low-grade solution employing a fixed-bed operation. The mill discharge from the milling-in-cyanide operation at a Witwatersrand gold mine was used as feed to the adsorption columns. A small amount of gold was leached during the milling process, so that this solution simulates, to a certain extent, a low-grade solution representative of a heap-leach operation. A speciation of the feed solution was done to establish which metal complexes were present in the milling-in-cyanide solution. This information was necessary to interpret metal loadings on the resin, as base metal cyanide species and their respective charges have an effect on the final gold loading capacity of the resin. Equilibrium isotherms were established for both adsorbents to estimate the rate of adsorbent flow anticipated for this specific feed solution. Breakthrough profiles were obtained at two different superficial linear velocities for each adsorbent. Mass transfer zone heights determined from the test work and the elution/regeneration time requirements were used to size a 150 m3/h full-scale plant for both adsorbents. A counter current configuration of adsorption columns, using three columns, should be suitable to recover gold effectively and to produce an effluent with a gold concentration below 0.01 mg/l. Based on the results obtained from the breakthrough tests, a preliminary techno-economic comparison was done between the resin-in-solution and carbon-in-solution options for the recovery of gold from low-grade solutions. This study indicated that the capital expenditure for a carbon-in-solution plant would be about 33 percent higher than that of a resin-in-solution plant. The operating expenditure for a resin-in-solution plant is expected to be only 60per cent of that for a carbon-in-solution plant. Keywords: resin-in-solution, carbon-in-solution, heap leach.

Jan 1, 2000

By E. Minnaar, P. J. Cilliers, M. Bellino, L. M. Roux, R. Dye

The classic technique to remove impurities in a cobalt stream is selective precipitation. This is usually followed by re-leaching to produce an advanced electrolyte for cobalt electrowinning. Although this technique ensures an adequate cobalt concentration in the electrowinning circuit, some of the consequences include unwanted losses through the numerous selective precipitation steps resulting in lower recoveries. One plant that currently utilizes selective precipitation is the Luilu Metallurgical Plant (Luilu) in the Democratic Republic of the Congo. This paper evaluates the benefits of using solvent extraction technology as a purification step in the Luilu Process with the aim of further increasing the overall cobalt recovery and to ensure that a suitable cobalt concentration in the advanced electrolyte is achieved. The implementation of a solvent extraction-electrowinning process is found to be beneficial in terms of achieving improved recoveries and cobalt cathode quality, however there are many other factors that impact the success of converting from the classic precipitation process used at Luilu.

Jan 1, 2007

By C. Liu, G. Zhu, Y. Liao

"The effect of particle size on the flotation kinetics of a low-rank coal was compared using air bubbles and oily bubbles. Five kinetic models were applied to the data from the tests to derive the relationships between the flotation rate constant, the ultimate recovery, and the particle size fraction. The results show that oily bubble flotation (OBF) resulted in a lower ash content and higher combustible recovery than air bubble flotation (ABF), especially for the -125 ??m size fraction. It was found that the flotation of a low-rank coal in individual size fractions using air bubbles and oily bubbles can be best described by a first-order model with rectangular distribution of tendency to float and the classical first-order model respectively. OBF yielded higher ultimate combustible and ultimate ash recoveries. The flotation rate constants for OBF were higher in all the models except for the fully mixed reactor model. The ultimate recovery values and modified rate constants first increased and then decreased as the size fraction decreased. The trend of the flotation rate constants as a function of the size fraction was similar in all the models except for the fully mixed reactor model. IntroductionFroth flotation is a physical-chemical separation method that is widely used in coal beneficiation for the separation of fine coal particles from associated minerals in water slurries. Since the cumulative recovery of a component in the concentrate is proportional to flotation time, the flotation process can be considered as a time-rate recovery process (Emad, Mohammad, and Bahram, 2010). Therefore, the general mathematical flotation models that incorporate both a recovery and a rate function can describe flotation time recovery profiles.The kinetics of coal flotation, as a measure of coal recovery as a function of time, have been studied in detail by many researchers. Different kinetic models have been proposed and published in the literature. The order and the rate constant are strongly dependent on the flotation conditions, such as the particle size and size distribution, the bubble concentration, the reagent concentrations, and the operating parameters (Zhang et al., 2013). The particle size has been reported to affect the flotation kinetics to a great extent (Yoon, Luttrell, and Asmatulu, 2002; Ntengwe and Witika, 2011). Numerous researchers have studied the aspects of flotation kinetics while paying special attention to particle size (Meftuni and Ibrahim, 1997; Rubinstein and Samygin, 1998; Graeme, 2012). However, the effect of particle size on the flotation kinetics of a low-rank coal has been relatively little discussed."

Jan 1, 2017

By H. Cevizci

"Numerical simulation of the plaster stemming method (PSM) was performed and compared with the conventional drill cuttings stemming method (DCSM). Many earlier in situ tests have proved that PSM can use the blast energy more efficiently than DCSM. Despite PSM generating more blast vibrations, it has advantages over DCSM such as better fragmentation and lower cost per unit volume of rock blasted. In this study, numerical simulation with Autodyn software using a 2D tool was employed to prove the efficiency of plaster stemming by comparing parameters such as pressure, Y-velocity, Y-force, internal energy, acceleration-Y, and compression. For example, the maximum pressure attained at the top of explosive column was 7 395 MPa for DCSM whereas it was as high as 11 945 MPa for PSM. Most of the computed parameters were significantly higher in PSM than those obtained for DCSM. This paper is the first study elucidating the efficiency of PSM by numerical simulation. It is concluded that PSM can save substantial amounts of money and effort. IntroductionThe stemming of blast-hole collars in surface mines with an inert material redirects blasting energy to the rock more efficiently, thus the blast-induced energy is utilized more effectively in breaking rock. With proper stemming, the gases should not escape due to loose stemming material. More efficient stemming with better confinement therefore increases the blast fragmentation. In addition, the distance of scatter is increased, giving rise to a looser rock pile that can be more easily loaded and transported. In order to improve the performance of a blast, stemming is used to help maintain the gas pressure over time (Konya and Konya, 2018). Proper stemming has been shown to increase the explosive efficiency by over 41% (Snelling and Hall, 1912).The most common stemming material in open pits and quarries is drill cuttings because of their ready availability at blast sites and the drill cuttings stemming method (DCSM) is a low-cost method. However, it has a major disadvantage in that dry drill cuttings eject very easily from blast-holes during an explosion, thus a great percentage of the blast energy is wasted and lost to the atmosphere. Cevizci (2012, 2014, 2013, 2017) studied blasting parameters in open pits and obtained better results with the plaster stemming method (PSM) in many limestone, basalt, and clay quarries. Moulding plaster is preferred for stemming because of the fast hardening time of 25–30 minutes."

May 1, 2019

By W. U. Reimold, R. Armstrong, R. G. Charlesworth

For many years rockbursts have plagued the mining industry. Although much research has gone into studying this phenomenon only a small proportion of it has been on the actual source mechanism. A study was recently carried out to compliment the previous work done on the micro-structure of these features and to compare it to the micro-structures seen on shatter cones, from meteorite impacts. Both optical and electron-microscopy were used during the study. Samples were collected from rockburst sites by the CSIR Miningtek Rockburst Investigation Unit, and from the collar of the Vredefort Impact Crater. In the optical-microscopy study, the pinnate fractures observed in previous studies were seen in the shatter cones, through all the material. In the rockburst samples, the fractures were observed only in the quartz grains. Quartz micro-crystals were present in the rockburst samples and appeared to be the product of comminution rather than crystallisation. Cataclasite was present on rockburst and shatter cone fracture surfaces. The observations of the shatter cone surfaces with the scanning electron microscope are in agreement with previous work, including the observed presence of melt features, spherules and spheroidal material. The deformation in the rockburst samples is concentrated in the quartz grains, highly complicated with brittle features like sub-conchoidal structures and step structures present. A quartz spherule was identified on one rockburst sample and rhombic-dodecahedra type micro-crystals were present and seen fracturing off quartz grains. It is clear that the rockburst and shatter cone fracture surfaces are quite different; the shatter cone deformation is equally distributed across the sample and involves plastic-deformation, while the deformation in the rockburst material is concentrated in the quartz grains and, with the exception of spherule formation, is brittle. This study agreed with the current explanation for the formation of the rhombic-dodecahedra, and disproved the possibility of it being coesite or fine-grained meta-chert. Although there is no definite evidence of the mechanism of formation of the spherule, it is believed to be the product of vaporization and condensation, and the presence of this material indicates the extreme conditions under which this event occurred.

Jan 1, 2003

By H. Möller, L. Mashigo, C. Gassmann

Wire-arc additive manufacturing (WAAM) is a directed-energy deposition technology that uses arc welding procedures to produce computer-aided designed parts, such as three-dimensional printed metal components. A challenge of additive manufacturing is the anisotropy. Interstitial elements play a significant role in the mechanical properties of Ti6Al4V of different grades. In this research, the mechanical properties of Grade 5 and Grade 23 Ti6Al4V were compared for this application. Samples were extracted from WAAM-produced Ti6Al4V walls in different directions (horizontal and vertical) and at different positions (top and bottom). The samples were subjected to optical microscopy and tensile and hardness tests. Grade 5 Ti6Al4V samples were found to have greater strength, greater hardness, and lower ductility, owing to the higher content of interstitial elements compared with Grade 23. The bottom samples had higher strength than the top samples, which is attributed to thermal cycling during manufacturing, resulting in different microstructures.

Jul 1, 2021

By I. Druce, C. Li, T. Qu, J. Dong, W. Y. Xinchao, V. Nkuna

CITIC Heavy Industries has a large installed base of grinding equipment throughout Africa in different configurations, including high-pressure grinding rollers with ball mill and semi-autogenous ball crusher. The total installed power of CITIC’s mills exceeds 430 MW. In this paper, we compare several typical grinding circuits of copper in Africa with about 15 kt/d throughput based on ore properties, process selection, equipment sizing, and key equipment capital and operating costs. Actual operating performance is also introduced. The comparison for the following mine sites provides a general reference for the selection of copper grinding circuits with this approximate throughput: Kamoa-Kakula Copper Mine with high-pressure grinding rollers with ball mill circuit, and Deziwa and Sicomine Copper-Cobalt Mines with semi-autogenous ball crusher circuits

Jan 1, 2023

By S. M. H. Haddad, M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

Sulfide impurities in iron ore concentrates play an important role in designing pelletising and steel making plants. Therefore attempts are made to keep the sulfur content of the final concentrate produced by the plants as low as possible. Generally, in the beneficiation process of iron ore concentrate, the removal of sulfur is performed through magnetic separation systems, followed by reverse flotation. The sulfide content of the iron ore concentrates originated from two main sources, including pyrite and pyrrhotite. In this research, in order to compare the floating capability of these two types of sulfide minerals, two iron ore concentrates with different sulfide constituents, pyrite or pyrrhotite, were selected. Reverse flotation tests were done separately on these samples under similar conditions. Process parameters considered for the tests included pH (2, 4, 6, 8 and 10), collector consumption (150, 200, 250, 300 and 350 g/t) and frother consumption (40, 50, 60, 70 and 80 g/t). Potassium Amyl Xanthate (PAX) and Methyl Isobutyl Carbinol (MIBC) were the collector and frother used in the tests, respectively. For modelling and optimising process parameters, the Central Composite Design (CCD) method was applied to the test results. Empirical coded equations were obtained for responses involving weight recovery, Fe recovery, Fe grade and S grade. Finally, comparison of test results revealed that the elimination recovery of pyrite sulfides was far greater than pyrrhotite sulfides, and it was possible to remove 84% sulfur content of the pyrite sample compared to minus 30% for the pyrrhotite sample. Keywords: Reverse flotation, pyrite and pyrrhotite, sulfur removal, iron ore concentrate, beneficiation plant

Jan 1, 2020

In order to test the applicability of elastodynamic codes in the modeling of mining related problems, comparisons are made between seismic data and numerical analyses. The dynamic finite difference program WA VE is used for the modeling of a horizontal stope in a deep mine. The slip along a vertical fault situated within the positive excess shear stress lobe of the stope initiates seismic waves. The stope-fault geometry is modeled in both two and three dimensions. The three dimensional non-slip weakening WAVE analyses correlate well with Brune's analytical model. For accurate modeling of the peak particle velocities predicted by McGarr's empirical relationship, it is recommended that a three-dimensional stope -fault model is used, with the amount of slip weakening dependent on the magnitude of the event.

Jan 1, 1995

By M. Gershon

During the exploration phase of mine development, drilling location is in the hands of the geologist, and drilling is spread over the entire domain of the property or deposit boundary. During the mine planning and production phases, however, the mining engineer also needs to use the information obtained from the drilling program. Thus it is important that he/she have some input into the selection of the drillhole locations. Usually, when exploitation will center on one portion of the property for the immediate future, the mine engineer will want to have more of the drilling performed in this area. In the early stages, the purpose of the drilling was to make a decision concerning whether or not to develop a mine. Once the decision is made to proceed with this development, the mine engineer needs to know, with as much confidence as possible, the estimate of the ore grade at each location where mining will occur. This paper addresses the problem of drillhole location for the needs of the mining engineer. The goal is to compare a variety of approaches to drillhole location with a new approach developed by the author. This approach is based on the theory of geostatistics, with the estimation variance used as the quantitative measure of the confidence attained. The goal of the algorithm is to select those locations that minimize the estimation variance subject to constraints on the number of drillholes and the total cost of the drilling program. The kriging equations are used as another set of constraints. The resulting nonlinear optimization model is expressed in terms of binary (0 - 1) decision variables leading to a solution by the branch-and-bound procedure. The algorithm has been applied at a number of operating properties, and practical results and suggestions for implementation are provided.

Jan 1, 1987

By R. Thomason

Thank you Dr Barcza, President of the South African Institute of Mining and Metallurgy, for inviting me to share our experiences in Australia as regards the competency movement and my Association?s experience in assisting engineers become managers. This is my second visit to South Africa, and I am struck by the similarities between our countries. This extends to the professional issues associated with engineering and competencies in particular. I propose to outline two exciting stories today. ? Development of competency standards for professional engineers in Australia. ? Development of a management programme which has assisted professional engineers regain positions of leadership in Australian industry and government. First of all I would like to outline the Association of Professional Engineers, Scientists and Managers, Australia(APESMA).

Jan 1, 1997

Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to RlOO for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute. A Student Member who is in fulltime study at a university may submit the dissertation or thesis he has to write in part fulfilment of his university degree, provided that it is presented in a manner and on a topic suitable for publication in the journal. Entries for 1976 should reach the Institute by 31st December, 1976.

Jan 10, 1976