Search Documents

By P. J. How, T. O. Hagan, M. F. Handley

Inelastic deformation of highly stressed rock in deep mines needs to be quantified in both time and space. Since most deformation occurs by shear, continuous monitoring of discontinuities in the rock from boreholes holds promise. The casing. Al interpretations of shear movements are based on a simple relation between shear displacement and the resulting change in tilt of the sensor. A prototype has been constructed and has undergone laboratory trials with satisfactory results. Underground trials will commence shortly. The instrument as designed has the potential for other applications, both in the civil-engineering and mining industries. paper describes an instrument that is both cheap and reliable, and capable of monitoring such shear movements continuously. The principle of operation is based on two capacitive gravity sensors mounted orthogonaly to each other in a sealed aluminum

Jan 1, 1988

By R. W. O. Kersten

Backfilling is one of the options available to the mining engineer in mine design. The decision as to the type of backfill is dependent on the purpose for which it will be used. For example, in a situation where high-grade, steeply dipping multiple reefs are to be mined, the purpose would be the following: ? to facilitate maximum extraction; a ? to minimize loss of fines; ? to allow closely spaced multiple reefs to be mined; and a ? to create a working platform. The physical properties required which will satisfy the abovementioned requirements can then be defined; the design of the fill plant, as well as the transport of the fill, will be governed by these considerations. The same procedure is also adopted in deciding on backfill in single- reef gold mines. The first question to be asked is the purpose of the fill. It may be to reduce the energy release rate, for environmental reasons, to reduce timber usage, to improve productivity, to reduce stoping costs, to obtain higher mining extraction, and so on. Only after one, or a combination, of these factors has been selected, can the specifications for the fill be decided on, and the plant designed accordingly. The introduction of backfill at Sheba Gold Mine will be used to illustrate the procedure adopted by Anglovaal in determining the type of fill required.

Jan 1, 1988

By S. M. Spottiswoode

A simple method for the application of excess shear stress (ESS) analysis to the mining of planar reefs is examined. The potential for seismicity associated with mining is expressed as the calculated increase in ESS on a regular grid of points 50 m above the reef, and is compared with observed seismicity around a deep-level, relatively geologicaly-undisturbed gold mine. Thirty regions were studied, involving over 2000 seismic events with magnitudes greater than 1,5 on the Richter scale and associated with almost 2 million square metres of stoping. The total seismicity, measured either as the number of seismic events or as the total radiated energy, corelated more closely with changes in ESS than with ERR. The incidence of rockbursts also favoured the ESS model. Corelation coeficients of around 0,8 for seismicity and ESS indicated that the assumptions inherent in the method used are collectively reasonable. The total seismicity in each region was found not to be strongly controlled by the presence of dykes and faults, although numerous individual seismic events were located close to such features.

Jan 1, 1988

By J. Svoboda, W. J. C. Venter, R. N. Guest

The use of gravity or magnetic separation followed by upgrading on a shaking table recovered about 25 per cent of the copper and lead minerals, at a combined metal grade of 20 per cent, from the final flotation tailing at the Tsumeb Mine. Magnetic separation recovered the copper minerals more efficiently than the lead minerals; it also recovered finer particles more efficiently than standard gravity separators. However, the grade of the concentrate produced by magnetic separation was not of sufficiently high grade, and further upgrading by gravity separation was necessary. It was decided to install an 'all-gravity' plant, which would have the added advantage of acting as a monitor or 'policeman' on a plant that receives a fairly variable feed.

Jan 1, 1988

By H. S. Eisner, J. -P. Leger

Published South African fatality and injury statistics for mine accidents are investigated. Where possible, the South African statistics are compared with those of other countries. Commonly held attitudes to the South African accident experience are also examined. Analysis reveals that the published accident rates present a more favourable picture than the rates actually experienced by underground workers. In addition, fatality rates in South African underground gold and coal mines do not differ significantly and have remained stable over the past decade, although the injury rates have decreased rapidly. No evidence was found that this is due to improved safety, and a comparison with international fatality and injury data suggests that it is not. The underground fatality rate for South African coal mining is, on average, eight times that of the UK, four times that of all EEC coal mines taken together, and over double that of the USA. Despite the unreliability of the injury rates, much has been made in South Africa of their rapid decline, an emphasis that appears to be misplaced.

Jan 1, 1988

By J. A. Cruise

From 27th to 29th September, The South African Institute of Mining and Metallurgy held a Colloquium on Equipment Alternatives in Underground Mining in Johannesburg. The Colloquium, which was highly successful, was held concurrently with the 1988 Electra Mining Exhibition. Particle characterization The Fourth European Symposium on Particle Characterization is to be held in Nirnberg, West Germany, from 19th to 21st April, 1989.

Jan 1, 1988

COUNCIL FOR 1987/88 President B.C. Alberts President-elect C.E. Fivaz Vice Presidents Senior Junior Dr O.K.H. Steffen H.G. Mosenthal Immediate Past President Dr H. Wagner Honorary Treasurer Dr H. Wagner

Jan 1, 1988

By I. H. Clark

A variety of backfills is presently being placed in different gold mines. The backfills are pumped as slurries to stopes where they are discharged into some form of retaining paddock. The effectiveness of fill as a support medium will depend on a number of factors. These can largely include (i) inherent properties of the material, e.g. particle size, shape, distribution and com- position, and (ii) conditions of placement. The terminology required for describing backfills is introduced, and the various laboratory-measured properties are presented for a variety of fills. Finally, the properties of the fills as they are placed underground are discussed.

Jan 1, 1988

By M. J. U. T. Van Wijngaarden, R. J. Dippenaar, J. M. A. Geldenhuis

The successful application of solid electrolytes in electrochemical cells for high-temperature thermodynamic studies depends to a large extent on an accurate knowledge of the P. value of the electrolyte (the oxygen partial pressure at which the ionic conductivity and n-type electronic conductivity of the electrolyte are equal). Consequently, the P. value of an electrolyte must be determined prior to its use in electrochemical cells. This paper describes the successful application of a coulometric titration technique in the quantitative assessment of the P. values of a commercially available ytria-stabilized zirconia electrolyte that has been used extensively by local investigators. The experimentally determined P. values of the electrolyte are reported and compared with P. values reported in the literature for a similar electrolyte.

Jan 1, 1988

By C. L. de Jongh

The number and scale of backfilling operations in the South African gold mining industry have grown rapidly in recent years. The application of backfilling as a means of stope support in a wide range of geological conditions and mining systems has resulted in the development of a variety of alternative fill systems. Experience gained in the evaluation of operating fill systems has contributed to a knowledge of the essential concepts to be considered in their design. This knowledge can also influence management's perception of what is expected of a backfilling system. The factors to be assessed in stating and satisfying these objectives are examined. The areas of investigation cover the selection of a suitable material, its preparation, distribution and placement, and the engineering logistics involved in the management of such a system. Finally, the integration of a filling system with an existing mining operation is examined.

Jan 1, 1988

By A. V. S. Meyer

The Colloquium held at Iscor, Pretoria, on 28th June, 1988, had as its objective the need for Quality Management Systems in the industry. Case studies of how problems were identified and solved by the use of such systems were submitted.

Jan 1, 1988

By M. H. Moys, K. S. Liddell

The dynamics of the ball load within a wet-grinding mil are examined, using measurements of torque and load position, The test equipment provided an accurate torque measurement, and the toe and shoulder positions of the load were measured by the use of a conductivity probe mounted in the mill shell. Both the variables tested-mil filing and rotational speed-influence the position of the load, and hence the torque, and have interactive effects on both the torque and the load position, An increase in mil speed and filing causes the torque to increase to a maximum value, after which further increases in speed or filing cause the torque to decrease. The position of the load toe is influenced only by the filing up to speeds of approximately 80 per cent of critical, whereas the speed and filing both cause the load shoulder to rise as their magnitudes are increased, The power drawn by the mill is predicted by the use of published equations, and these values are compared with the measured power draw.

Jan 1, 1988

By M. F. G. Bruce

Two backfill systems have been developed on West Driefontein, namely the centrifuge dewatered tailings system and the cyclone-classified tailings system. Modifications to the two systems since the publication of the original paper (Close and Klokow, 1985) are discussed in addition to the results obtained. Considerable experience has been gained from the operation of the centrifuge dewatering units as well as the placement of dewatered tailings in a difficult mine environment. The centrifuge dewatered tailings method has proved successful in the extraction of a highly stressed block of ground at No. 5A Sub-vertical Shaft. The utilization of backfill support in this area made it possible to dispose of a high-grade barrier pillar. This pillar was considered necessary prior to the introduction of backfill support. The recovery of the gold from this pillar made the use of dewatered tailings backfill cost- effective, despite high labour and maintenance costs. Current experience with the bagfilling method of placing cyclone- classified tailings indicates that it is viable and requires considerably less capital investment. Although expensive at present, it is envisaged that costs will decrease once cheaper bags and other forms of stope support are used. The placement of backfill in small-diameter sausage-type bags requires no change in mining cycle and allows the backfill to be placed close to the stope face. Both backfill systems are being expanded but preference is to be given to the cyclone-classified tailings system.

Jan 1, 1988

The refractoriness of the gold in many of the pyritic ores from the eastern Transvaal is due mainly to the association between the gold and the sulphides, but it can be due to the presence of graphltlc carbonaceous material, which complicates the recovery of the gold by virtue of its adsorption activity. In an examination of the roasting characteristics of three flotation concentrates from the Barberton area, It was found that the gold in the concentrates occurred mostly in two forms: in very fine gold particles distributed within the arsenopyrite, and in a slightly coarser form loosely associated with the pyrite. Direct cyanidation of the concentrates gave gold extractions of from 16 to 30 per cent. After the concentrates had been roasted at temperatures of 650 to 700°C for 20 minutes with rabbling, the extractions varied from 86 to over 90 per cent. Examination of the residues after cyanidation indicated that gold was present in the porous calcines or in the calcined sulphide product. This observation, together with porosity measurements, suggests that physical encapsulation of the gold particles is the main reason for the refractory behaviour of the gold in the calcines.

Jan 1, 1988

By A. C. Wingrove

The paper outlines the selection of a dewatered tailings backfill system for the Johannesburg Consolidated Investment Gold Division, and covers the following aspects: (i) 16 Shaft pilot testwork; (ii) engineering design problems relating to the Cooke 3 Shaft backfill operation; (iii) in-line mixing - applications with respect to the Randfontein Estates Gold Mine and Western Areas Gold Mine backfill operations; and (iv) pipeline friction losses.

Jan 1, 1988

The special mixing requirements for backfilling are discussed, and the problems associated with the mixing of coarse and deslimed slurries, as well as the tailings from the gold plant are outlined. The mixing of binders which are used to strengthen backfill and the parameters for the scale-up of mixer pilot plant work are also discussed

Jan 1, 1988

By A. R. L. Thoresson, S. J. Lennon, F. P. A. Robinson

This paper reports and discusses experimental work carried out on heavy nickel-electroplated turbine-disc steel. Mechanical and fatigue tests were used to determine whether the coating was suitable for turbine-disc applications. It was concluded that dehydrogenation treatment is necessary in order to produce compatibility of the coating and substrate

Jan 1, 1988

By S. M. Spottiswoode

Rock mechanics benefits of stope support in deep-level mining originate principally from the ability of the support to resist relative movements between the hangingwall and the footwall. While the role of stabilizing pillars and backfill on reducing the energy release rate (ERR) at the face is well understood on the basis of elastic behaviour of the rock mass, the effect of support on controlling movement of fractured ground around deep-level stopes has not yet been thoroughly studied. As part of a programme of studying the behaviour of this fractured ground, geophones were placed 10 m from the face on the roof and floor of a longwall stope in which packs were used as supports. It was found that differential movement between the roof and floor generally exceeds average stope movement during a seismic event. Conventional support therefore transmits very little seismic energy; this is expected to remain true until complete convergence occurs. In backfilled stopes, backfill can become at least as stiff as the fractured wall rock. This will have the effect of reducing the length of the hanging- wall beam. Amongst other rock mechanics considerations, a shorter hanging- wall beam should: (i) increase the resonance frequency of the hangingwall and thereby decrease the levels of vibration for seismic events with M > 1,0; (ii) reduce absolute vibration levels by increasing the mass of rock immediately adjacent to the stope which is shaken by seismic waves; and (iii) reduce differential movement between the roof and floor and thereby reduce cyclic strain on the backfill and on gully support.

Jan 1, 1988

This paper details the preliminary design work carried out before and during the implementation of an extensive backfilling programme on Cooke 3 Shaft, Randfontein Estates Gold Mining Company (Witwatersrand) Limited. The design work is of relevance to any system utilizing a cementitious binder, and the quality control aspects are of particular significance. Problems associated with correlating laboratory results to actual field results are also briefly discussed.

Jan 1, 1988

1. Journals Marine Geotechnology, edited by R.C. Chaney. London, Taylor & Francis (Rankine Road, Basingstoke, Hants RG 24 OPR, OK), 1988. vol. 8, $50. Published quarterly. Mineral Resources Engineering, edited by C.T. Shaw. London, Taylor & Francis (address as above), 1988. vol. 1, $99. Published quarterly. 2. New publication World mining map of non-ferous metals (with 4 regional maps and a booklet). Reinhard Ryborsch (Postfach 2105, D-6053 Obertshausen bei Frankfurt am Main, West Germany). International edition: bilingual, English and German. 7 colour-print: Size (unfolded) 138 X 100 cm. US$ 19 (excl. mailing) for folded map with hard cover (Order No. 61-4); US$ 25 (excl. mailing) for unfolded (flat) map with hanging strip (Order No. 62-2). 3. Mintek reports Report M326 Crevice corosion and other localized corosion behaviour of 3CR12 corosion-resisting steel in synthetic minewaters, by D. Howarth. May 1988. 28 pp.Report M332 The carbon-regeneration furnaces at Mintek, by P.M. Cole and P.J. van Staden. Nov. 1987. 31 pp. Report M344 The flotation of pyrite with amine colectors, by R.D. Hil, E.W. Giesekke, and P.J. Haris. Mar.'1988. 25 pp.Report M345 The substitution for chromium in steels: Progress and trends, by M.B. Cortie. Mar. 1988. 14 pp.Report M346 The direct reduction of sulphur dioxide to elementalsulphur, by I. Henderson. Mar. 1988. 30 pp.Report M349 The optimization of a process using weak-base resin for the recovery of gold from plant solutions and pulps, by A. Mehmet. Apr. 1988. 17 pp. Report M353 The determination, by ion-interaction chromatography, of sulphur species in cyanide solutions, by Pohlandt-Watson, M.J. Hemmings, D.E. Barnes, and a.w. PansL Jun. 1988. 7 pp. Report M355 A laboratory-scale continuous-feed resistance furnace, by K.P.D. Pery, A.S.E. Kleyenstiber, andC.T. Logan. May 1988. 9 pp. Report M357 The determination of minor and trace elements in activated charcoal, by RT. Eddy and G.J. Wal. Jun. 1988. 14 pp. Report M358 The sensitive determination of germanium by atomicabsorption spectrophotometry using electrothermal atomization, by G.D. Marshal. Jun. 1988. 11 pp. Report M92D The recovery of tin and tungsten from various zones of the Van Roois Vley deposit, including setling and filtration, by C.F.B. Coetzee. First issued Apr. 1983; reissued Apr. 1988. 40 pp. World Environment Day Symposium* Mintek auditorium in Randburg was the venue on Thursday, 2nd June, 1988, for more than 200 interested delegates at the annual World Environment Day Symposium, organized jointly by the Federation of Societies of Professional Engineers (FSPE), The Environmental Planning Professions Inter-disciplinary Committee (EPPIC), The Habitat Council, and The Associated Scientific and Technical Societies of South Africa (AS&TS). The theme 'Cultural and Historical Conservation' was adapted from the theme of the Department of Environment Affairs for the 1988 Environment Week.

Jan 1, 1988