Search Documents

By E. Matinde, S. L. Msibi

"The robust nature of alumina refractory materials presents opportunities for their in-process reclaiming and re-use in non-critical applications. Virgin refractories can be substituted with different quantities of reclaimed materials without compromising the quality of the refractory products. In this study, the effect of reclaimed bauxite on andalusite-containing refractory castables for tundish applications was investigated. The recycled bauxite was formulated in different proportions to replace virgin andalusite in the castables. Standard tests were conducted to evaluate the physical, physicochemical, and thermochemical properties of the formulated products. Static corrosion tests were conducted using tundish slag in order to simulate the actual operating conditions. The results show that the standard flow behaviour, open porosity, and bulk density of samples containing up to 22 mass% reclaimed bauxite were comparable to those of the reference castable. However, high-temperature properties such as static corrosion at 1400°C and hot modulus of rupture at 1500°C indicated that there is an upper constraint to the amount of substitution. The study demonstrated direct potential savings of up to 10% when the reclaimed alumina replacement ratio was increased to 22 mass%. IntroductionAlumina-based refractories can be classified into low-alumina, containing less than 50% Al2O3, and high-alumina or bauxite, containing between 50 and 90% Al2O3. High-alumina refractories have widespread applications in high-temperature metal extraction processes due to their outstanding thermochemical and thermomechanical properties and stability (Rebouillat and Rigaud, 2002; Frulli, 2016). The typical chemical composition of refractory-grade bauxite consists of 85–90 wt.% Al2O3, 5–10 wt.% SiO2, 1–2wt.% Fe2O3, 3–4 wt.% TiO2, 0.4–0.8 wt.% CaO + MgO, and 0.20–0.8 wt.% K2O + Na2O (Nyoka et al., 2013). The thermochemical and thermomechanical properties of bauxite-based refractories rely principally on the conversion of the contained silica and alumina to the highly stable corundum (?-Al2O3) and mullite (3Al2O3· 2SiO2) phases (Rebouillat and Rigaud, 2002; Hill and Sehnke, 2006; Garbers-Craig, 2008; Frulli, 2016)."

Jun 1, 2019

By M. Izadi Yazdan-Abadi, S. H. Amiri, M. Ramezanizadeh, M. Bazmandeh

Iron ore concentrate is used as the fresh feed of pelletising plants. The green pellet properties depend on iron concentrate characteristics such as particle size distribution (PSD), specific surface area (Blaine value), iron grade, moisture content and grinding methods. The grinding methods affects particle size distribution and Blaine value. To find out the effects of grinding methods on pelletising process, green pellets were produced with concentrates that were reground by means of HPGR (high pressure grinding rolls) and ball mill. The Blaine values of ground concentrates in both types of milling were approximately 1400, 1600 and 1800 cm2/gr. The results of green pelletising tests on a pilot plant scale showed that at the same Blaine values, drop numbers of green pellets produced by ground concentrate inside HPGR were higher than the green pellets produced by ground concentrate inside a ball mill. Also, reground concentrates by means of HPGR, in comparison with ball mill, caused the production of green pellets, at higher wet and dry compression strengths. As a result, it was found that preparing the pelletising feed by means of HPGR led to more positive effects on the properties of green pellets. Keywords: Ball mill, HPGR, green pellet, drop number, wet and dry compression strengths

Jan 1, 2020

By A. J. S. Benade, A. J. A. Heyns, N. B. Strydom

The maximum oxygen intakes of samples of about 30 Bantu, weighing less than 50 kg from different tribal groups (Zulu, Xhosa, Sotho and Shangaan) were measured on a treadmill. The mean maximum oxygen intake of the 164 men was 2,12 litresjmin and only 18 men (11 per cent of the sample) had maximum oxygen intakes of 2,5 litres/min or above (the minimum requirement for such tasks as shovelling rocks and tramming it). The samples of the different tribes differ in age, but when the age effect is taken into account then there were no significant differences between tribes in maximum oxygen intakes. An incidental finding was that both age and body weight correlated significantly with the maximum oxygen intakes of these underweight subjects. Not one of the subjects who weighed less than 45 kg or who was older than 40 years had maximum oxygen intakes high enough to permit their being able to do strenuous work underground. It is clear therefore that Bantu who weigh less than 45 kg or are older than 40 years should not be employed on such strenuous tasks as shovelling rock and tramming it.

By A. García-Gutiérrez, A. Aragón-Jerónimo, R. Salazar-Mendoza

A theoretical analysis of a two-region solid-liquid flow system in horizontal pipes is presented, which considers a stationary bed of drill cuttings as a porous medium (-region) below of a two-phase dispersed flow (-region).The method of volume averaging was applied in this study to derive a rigorous mathematical model in which each variable is precisely defined. This model includes the volume-averaged transport equations for both the two-phase dispersed flow and the porous medium regions and terms from a macroscopic forces balance. The solution of the two-region model allowed evaluation of the behaviour of pressure gradient as a function of velocity, total volume fraction of cuttings and the relationship of the height of the stationary bed and pipe diameter. The solution is based on a backward finite difference explicit scheme. The simulated physical system is a pipe of 4.135 m in horizontal length and 0.0508 m in diameter. A one-dimensional, mesh-centred grid, consisting of 100 nodes, is used. The numerical results were compared with experimental data on slurry flows and a good agreement was found. Keywords: two-phase, cuttings transport, solid-liquid flow, drilling modelling, volume averaging.

Jan 1, 2007

By Peter Voulgaris, Allan Haines, Diane Walker, Ian de Bruyn

The Oyu Tolgoi porphyry gold and copper project is located in the south Gobi region of Mongolia. The Ivanhoe Mines project has the potential to become a long-life copper and gold producer that could rank among the largest in the world. There are five deposits which cover a strike length in excess of 6.5 km, from south to north they are named South Oyu, Southwest Oyu, Central Oyu, Hugo South and Hugo North. The first three, collectively known as the Southern Oyu deposits, are planned to be mined by open pits, whilst extraction of the deeper Hugo deposits is planned using block caving techniques. The pits will have diameters of approximately 1000m and a maximum depth of 550m. The geological environment consists of a sequence of porphyritic augite basalt, dacitic tuffs and sedimentary rocks that have been intruded by several generations of porphyritic quartz monzodiorite and numerous post mineralization dykes. Several major faults cut through the southern deposits juxtaposing the relative position of the stratigraphy. The geotechnical investigation for the Oyu Tolgoi Open Pits was conducted in three distinct phases of increasing complexity: scoping study; advanced scoping study and feasibility study. Each phase consisted of data collection, interpretation and analysis designed to progressively develop 3D geotechnical domaining for the empirical, structural and numerical evaluations. The development of the geotechnical design parameters for these green fields open pits posed many technical challenges, brought about by the conditions associated with a lithologically and structurally complex environment. The design work focused on the optimization of the pit geometry to conform to equipment selection and blasting characteristics. Limiting bench stack heights were derived from the influence of major structures. The overall slope angles in each pit sector were developed around the requirement for haulage ramps and geotechnical berms. This paper describes each of these aspects and the methodology used to address the integration of the geotechnical characteristics with the mining environment.

Jan 1, 2006

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of 'Google maps?' underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum's new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2013

By M. Pierce, E. Karampinos

"One of the main challenges in the numerical modelling of ground support in underground excavations is to reproduce the performance of the sequential installation of the reinforcement while capturing the rock mass behaviour of an advancing face in 3D. The 3D modelling approaches used to simulate the progressive advance of excavations are mostly continuum and often cannot reproduce the rock mass failure mechanisms. The 3D discrete element method (DEM) can better reproduce structurally controlled rock mass failure mechanisms and can explicitly represent the reinforcement elements. This paper builds on previous work that reproduced the structurally controlled squeezing conditions in an underground hard-rock mine using 3D DEM and the in situ behaviour of reinforcement under pull conditions. It addresses important issues on the way reinforcement is explicitly introduced in discrete element models. A pseudo-3D model is employed to overcome the computational restrictions and time limitations of a 3D modelling approach. The work focuses on the scaling of the material properties of the ground support elements when the thickness of the model is not equal to the out-of-plane spacing of reinforcement. It demonstrates the scaling methodology based on the type of the modelled reinforcement elements used and investigates the significance of this approach. The advantages and disadvantages of this approach with respect to 2D and 3D methods are discussed. The results are compared with field data and previous modelling work done at the mine. IntroductionNumerical models can provide significant insight into the anticipated behaviour of underground excavations. The modelling of ground support, however, is not a trivial exercise. An effective representation of ground support in underground excavations should capture the behaviour of both the rock mass and the support elements. When numerical models are used for design purposes, the complexity of the problem requires significant time and expertise (Sweby, Dight, and Potvin, 2016).At a laboratory scale, numerical models have successfully reproduced the results of laboratory tests on rockbolts by explicit modelling of the bolt, the borehole, and the grout. Chen and Li (2015) used a continuum FLAC3D (Itasca Consulting Group Inc., 2012) model to simulate the mechanical behaviour of D-bolts as observed experimentally. Grasselli (2005) used a 3D finite element code to model the behaviour of fully grouted rods and expandable bolts under shear."

Dec 1, 2018

By K. Thuro, R. J. Plinninger

ABSTRACT: Determining tunnel stability is a key issue during preliminary site investigation. In contrast, problems of excavatability have been largely ignored. While the choice of an economic tunnelling method is admittedly a clear priority in the planning stage, special investigations focus-sing on rock fragmentation (e.g. drilling or cutting performance, rock mass blastability or tool wear) are rarely carried out. This paper explores possibilities to quantify key parameters for rock mass excavatability in drilling, blasting and cutting by TBMs and roadheaders. RÉSUMÉE: La détermination de la stabilité du tunnel est une question clé lors des études prélimi-naires. En revanche, les problèmes d'excavabilité sont souvent en grande partie ignorés. Tandis que le choix d'une méthode de percement économique est évidemment une priorité claire dans l'étape de planification, des investigations spéciales se concentrant sur la fragmentation de la roche (par exemple le comportement de la roche au forage, à l’excavation ou au dynamitage et l’usure des outil) sont rarement effectuées. Cet article explore les possibilités pour quantifier les paramè-tres clé de la roche lors d’excavation par forage, dynamitage, au tunnelier (TBMs) ou à l’excavatrice. ZUSAMMENFASSUNG: Beim Tunnelbau wir meist die Vorhersage der Stabilität des ausgebrochenen Hohlraums als Schlüsselfragestellung betrachtet. Im Gegensatz dazu werden Probleme der Gebirgslösung weitgehend ignoriert. Während der Wahl einer wirtschaftlichen Vortriebsmethode während der Planungsphase meist noch eine gewisse Priorität beigemessen wird, werden spezielle Untersuchungen zur Gebirgslösung (Bohr- oder Schneidbarkeit, Sprengbarkeit oder Werkzeugverbrauch) nur sehr selten durchgeführt. Diese Publikation zeigt Möglichkeiten der Quantifizierung von Schlüsselparametern für die Gebirgslösbarkeit auf, also der Bohr- und Sprengbarkeit, der Fräsbarkeit mit Teilschnittmaschinen und der Schneidbarkeit mit TBMs.

Jan 1, 2003

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By A. F. Lee

Dr E. C. Hanekom (Visitor): Two years ago we used the bubble pick-up technique as developed at Anglo American Corporation for screening candidate flotation agents prepared in our laboratories. It was obviously necessary to know to what extent the technique gave reproducible results and a statistical evaluation of the test method was made using a mineral sample provided by Anglo American Corporation. A bubble of 2.0 mm diameter was used and the measuring graticule was divided into squares (units) with sides of 5.0 mm at 25 X magnification. The mineral granules had diameters from 53 to 74 mm. The bubble was loaded by depressing it against a layer of mineral grains to give an arbitrary but constant compression of 0.4-0.5 mm. It was rolled five times through 2 mm horizontal displacement. The bubble was then lifted, its load compacted by gently stirring and the projected area measured in squares (units) on the grid. Each substance was tested at 5 ppm concentration in distilled water at five points in the pH range 3-6. With these standardized conditions of operation the reproducibility of the test was studied. Four materials were tested and at each pH value the procedure of forming a bubble, picking up granules and counting the units was repeated ten times. From these results the standard deviation for a single count at any pH value was calculated for each material (Table 1. The coefficient of variation of approximately 3 per cent was relatively low and it was decided that further refinements in the counting procedure would be of doubtful benefit with the present apparatus. Similar experiments were carried out with 12 sample materials. In this case the bubble formation and pick-up were repeated four times at each pH value, the mean value was calculated for each set of four observations and final pick-up values for the materials were obtained by selecting the highest mean count. Each test was completely repeated a number of times as indicated in Table 2 and the standard deviation calculated. The results allowed the selection of the more promising materials and the rejection of poor performers at the 95 per cent confidence level. All tests were carried out by one operator. Some evidence was obtained that the method is sensitive to operator bias. In conclusion it can be said that from all the results analyzed it would appear that once operation conditions are fixed (viz operator, pH control) the precision of the method is adequate. The author wishes to thank Messrs African Explosives and Chemical Industries Limited for permission to publish these data. G. S. Stander and C. J. Kooij (Visitors): We must congratulate Mr Lee for this most interesting and useful development of the pick-up experimental method. It certainly provides research workers with an instrument which makes flotation more of a science and less of an art. We visited Mr Lee at his laboratory where he gave us a demonstration of the bubble pick-up instrument and technique as developed and improved by him.

Jan 12, 1969

An extensive laboratory grinding study was carried out on a magnetite ore in order to assess the grinding behaviour of magnetic concentrate and tail from low intensity magnetic separation (LIMS).The test work involved Bond ball mill testing, rod milling, low intensity magnetic separation (LIMS), and batch ball milling down to product sizes of around P80~25 microns. A total of 18 Bond tests and over 150 batch grinding tests and sieve sizing were carried out. Throughout the grinding tests, power draw was continuously monitored. The relationship between the grinding energy and product size was analysed using the conventional energy-size concepts. It was found that the Rittinger equation fits the experimental data well. However, Bond?s equation does not fit the experimental data well, and therefore a modified Bond equation was developed. Differences in grinding properties between the magnetic and non-magnetic component were analysed and compared to the bulk ore. It was found that grinding properties differ significantly and therefore separate grinding test work may be required for each grinding step in the magnetite ore beneficiation flowsheet. Keywords: grinding, iron ores, particle size, modelling.

Jan 1, 2010

The French research institute, INERIS, requested the assistance of the CSIR?s Division of Mining Technology in developing further precautionary measures against explosions in their collieries. In response to this approach, an on-board active suppression system was adapted to meet their mining requirements. This system is used on tunnelling machines in Germany where the machine is positioned in the middle of the tunnel, which is therefore not much wider than the machine itself. With this configuration, the machine is never away from the tunnel face during the cutting cycle. As a result, the possible volume in front of the machine of combustible gas requiring suppression is less than 50 m3. In South Africa this technology has been adapted to suit a two-cut mining method which entails greater distances from the face and thus much larger volumes of methane mixtures requiring suppression. The particular configuration of the Explo-Stop® system being investigated required the suppression of possible methane ignition volumes of up to 180 m3of a 9% per volume methane/air mixture. The volume is a consequence of the large cross-sectional area of French underground workings and of the two-cut mining method used in France. In order to take the second cut in the coal seam, the machine is pulled back a maximum distance of 4 m, leaving an air pocket in which gas can accumulate. The machine-mounted system is required to effectively suppress any flame ignited by such a large accumulated volume of methane. The results of the protocol tests done at Kloppersbos showed that the system was capable of suppressing all simulated methane ignitions for the prescribed conditions. This was achieved with a temperature increase of less than a 100°C at the operator?s position and without any flame being detected at this position.

Jan 1, 2001

By T. Moodleya, I. Govender

Despite the widespread use of DEM to simulate particle processes, comparatively little work has been done to evaluate its accuracy. One of the reasons is a lack of available measurement techniques that can capture dynamic information at the momentum transfer timescale which is lower than 10-6 s - typical of the kinetics occurring within the drum. This work makes use of Positron Emission Particle Tracking (PEPT), an in-situ method capable of measuring 3D kinematic data at 1000 frames per second. PEPT measurements are performed using 3 mm and 5 mm mono-size glass beads in a 300 mm diameter rotating drum at critical speeds that are relevant to industry. We undertake systematic ‘tuning’ of DEM with a view to optimising the agreement between experiment and simulation. To ensure an equitable comparison scale, both the DEM and PEPT data are coarse grained within representative volume elements. This work seeks to validate DEM predictions against experimentally derived PEPT kinematic measurements. Keywords: PEPT, nuclear imaging, DEM, Tumbling Mills

Jan 1, 2020

By H. Gumede

The challenges of noise emission in the mining industry are well known. These challenges are exacerbated by the increasing trend towards mechanized mining, and there is general consensus that an effective industry-wide Buy Quiet initiative (BQI) will significantly assist in reducing noise-induced hearing loss by minimizing noise at its source. In its endeavours to improve the health of workers, the MOSH Noise Team has facilitated development of a proposed strategy and structure for a BQI. Extensive consultation with stakeholders resulted in support for the initiative. The MOSH Noise Team was advised to solicit the contributions of consulting mechanical and electrical engineers (CM&EEs), whose support is viewed as critical for realization of the initiative, since elimination of noise at source is an engineering challenge, and most procurement standards and specifications are set and managed by engineers. A workshop with CM&EEs and their representatives, as well as group environmental engineers (GEEs), confirmed the urgent need for the initiative and provided valuable insights. The workshop used obstacle based planning techniques to identify the factors on which the success of this BQI will depend. Most potential obstacles to the implementation revolved around proper scoping, leadership commitment, and companies? adherence to the initiative. Lack of involvement by the relevant stakeholders and economic issues were also identified as potential obstacles. Delegates at the workshop felt that the successful implementation of the industry-wide BQI, will depend on the mining industry addressing the specific obstacles. The most critical and urgent issue was identified as the formation of a properly constituted industry-wide BQI task team that includes representatives from critical stakeholder groups and which is mandated and empowered to drive the initiative.

Jan 1, 2014

By N. Kumar, A. K. Dhawan, A. Varughese, S. K. Khullar

Abstract The in-situ stress field is one of the primary parameters influencing the performance of underground structures particularly in the Himalayas where there is strong influence of topography and geology on in-situ stresses. It is always advisable to measure the in-situ stresses, in whatever best way possible. Hydrofracturing is one of the methods by which in-situ stress can be measured. This paper briefly describes details of the concept of Hydrofracturing in arriving at the in-situ stresses of the rock mass at Pancheswar Project. The data obtained from the tests has been analysed, interpreted and the results are presented in this paper. Kurzfassung Das Spannungsfeld an Ort und Stelle ist einer der wichtigsten Parameter, die das Verhalten der Untergrund-Struktur beeinflussen, insbesondere in den Himalayas, wo die Topografie und die Geologie einen grossen Einfluss auf die oertlichen Spannungen ausueben. Es empfiehlt sich stets die Spannungen an Ort und Stelle so gut wie moeglich zu erfassen. Die Hydrofraktur bzw hydrografisches Zerstueckeln ist eine der Methoden, die bei den Messungen der oertlichen Spannungen verwendet werden koennen. Diese Abhandlung beschreibt kurz Einzelheiten ueber das Konzept von Hydrofraktur bei der Bestimmung der Spannungen an Ort und Stelle von der Felsmasse bezueglich des Projekts Pancheshwar. Die gewonnenen Daten aus den Messungen wurden analysieret und ausgewertet. Die Ergebnisse werden dabei vorgelegt. Sommaire Le champ de contraintes in-situ est un des paramèters principaux influencant l’exécution des structures souterraines particulierèment en Himalaya où les forces in-situ sont fortement influencées par les caractéristiques topographiques et géologiques de la région. La fracturation hydraulique est une technique qui permet de mesurer des forces in-situ des massifs rocheux. Cet article décrit brièvement le mécanisme de fracturation hydraulique et présente les résultats de mesure des forces in-situ des roches au site du projet hydroélectrique de Pancheswar.

Jan 1, 2003

By M. Handley

The Witwatersrand Basin contains by far the most gold ever found, and has hosted mining from its discovery in 1886 to the present. For many years, South Africa was the world’s largest producerof gold, nearly all of which came from the Witwatersrand. Since 2000, South Africa has fallen back several positions because of declining gold output. There are many complex and varied reasons for this; however, declining gold resources in the Witwatersrand Basin are not one of them. As far as the author knows, there are no qualified estimates in the literature of gold remaining in the Witwatersrand Basin. This paper collects mining data from several sources and then, using elementary gold accounting and error analysis, attempts to estimate the amount of gold remaining in the Witwatersrand Basin. It includes gold underground in existing and defunct mines, in evaluated ore resources, and dumps. Compiled data from 1887 to 2019 shows that 50 200 t of gold were produced by Witwatersrand mines, while it is estimated that a further 48 100 t remainunderground, both within and outside of mine leases, a further 1 600 t on the surface in tailings,and an unknown amount in rock dumps. Nearly all of this gold will remain inaccessible with current mining methods, and major technical developments in mining will be necessary before any of the gold can be categorized as a code-compliant resource or reserve. To win this prize, the mining industry will have to rethink its approach to mining, both in old mining leases and in the unexploited ground. It will also have to find effective means of preventing gold theft and informal mining, which are on the rise.

Apr 5, 2023

By R. G. B. Pickering

Resue mining was practiced extensively in the East Rand in the first half of this century. The obvious benefits were that a higher grade of ore was trammed to the surface. The disadvantages were slow rates of face advance and an extremely labour-intensive method of mining. A collaborative effort by personnel from Avgold?s Target Gold Mine and Sandvik Tamrock has resulted in the design of a method of resue mining which can be totally mechanized. The purpose of this paper is to describe the methodology used and the proposed new mechanized resue mining method.

Jan 1, 2000

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999

By P. S. Turner

After a brief account of the differences between the control of underground fires and those on the surface, the paper describes the analogue detection system used on the mines of the Anglo American Corporation of South Africa Limited. The system comprises Spanair gas analysers, Becon combustion-particle detectors, a telemetering system, a surface signal-recording and-processing system, and an alarm system. The use of the system is described and illustrated.

Jan 1, 1982

By J. E. Robinson, W. Pilkington, J. L. Taylor, B. J. Bluhm, E. B. Viljoen, P. Le Grange

The Chemwes uranium plant was designed and constructed within fifteen months; commissioning started during. June 1979, and the plant was producing at design capacity four months later. This account highlights the procedures and methods adopted to bring the plant Into production. The description of the various phases includes some details of the early evaluation, and the feasibility and optimization studies; of the financing, project management, design, construction, and commissioning of the plant; and of the training of personnel. Some of the mistakes made and the factors that contributed to the success are also listed.

Jan 1, 1981