Search Documents

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

By C. Dorfling, M. Tadie, M. Tucker

Electrowinning is the final step in the hydrometallurgical production of high purity copper, involving the passage of electric current through an electrolyte and consequent plating of solid copper to form cathode sheets. Key electrowinning performance indicators are the current efficiency, specific energy consumption, yield, and quality of the metal. The high energy demand and associated cost mean that determination of performance indicators is critical during operation, but ‘online’ measurement is impractical due to the nature of the measurements and corrosive environment brought about by acid mist. This research considered the development of a predictive electrowinning model as a shift towards a pre-emptive approach to attaining plant performance data. A steady-state model was created from input variables available in the industry, using a first-principles approach combining mass balances, electrochemical and thermodynamic equations, and property correlations. A circuit diagram equivalent of an electrowinning cell, containing multiple pairs of electrodes, was used as the backbone of the model. The kinetics of each electrochemical reaction were modelled including iron as a major impurity. Losses in current efficiency due to ineffective electrode contact, short circuits, and stray currents were also incorporated. The model was used to predict the current efficiencies for tests performed at varying conditions in a bench-scale electrowinning cell; the average absolute error between the measured and predicted current efficiencies was 3.2%. The model requires a unique parameter fitting approach for each industrial operation; if parameters are customised for specific plants, the model will be a useful tool to predict performance and can aid the development of effective process control systems in copper electrowinning tank houses. Keywords: Copper; current efficiency; electrowinning; modelling; plating rate

Jan 1, 2020

By H. von Blottnitz, B. E. Isheloke

Mining is a significant economic activity in most Southern African Development Community (SADC) countries, and mineral beneficiation has been identified, and controversially discussed as one of the possibilities for industrialisation. With many member countries being economically too small to muster the human and financial resources which beneficiation requires, the recently adopted Regional Mining Vision (RMV) envisages interventions at a regional level. An opportunity arose to ask industry role players to what extent the SADC appears to support regional beneficiation policy interventions undertaken by member countries, and what the challenges are in undertaking beneficiation regionally, as a complement to, or substitute for country-specific beneficiation policies. Twenty-five semistructured interviews were conducted with experts from SADC member countries during the 2019 Mining Indaba. Participants were divided on whether beneficiation should be carried out nationally or in the SADC region. While beneficiation could support value-keeping, key challenges were found to be infrastructure development (i.e. energy, water), scarce skills, access to technology and related costs, but also lack of free trade and movement. We submit that a more integrated beneficiation strategy for the SADC region, as is being developed through the RMV, would indeed be relevant in the future. Keywords: Mineral beneficiation, regional integration, beneficiation policy interventions, African mining vision, mining, SADC

Jan 1, 2020

By V. Sheikhzadeh, S. M. H. Haddad, M. Saghaeian, N. Esmaeili, R. Hejazi

One of the most significant features of iron ore concentrate (pelletising feed) is the specific surface area (SSA) that affects the achievement of desirable pellet properties. There are various methods to determine this parameters and currently, the most common is the Blaine air permeability method. However, due to the simplified assumptions including spherical and identical particles and 50% bed porosity, the Blain test does not provide accurate results. In fact, these two suppositions are far from reality. In this research, comparison of SSA measurement ways are investigated, containing laser diffraction testing and Blaine air permeability, on samples with different SSA, obtained from Ball mill and high pressure grinding rolls (HPGR). The output data showed that the calculated amounts of SSA by means of laser analysis were far greater than any other one. Furthermore, in the same results of Blaine air permeability tests on samples comminuted by different grinding methods, it was observed that the SSA figures from the laser diffraction method for HPGR products were almost 800 units greater than Ball mill ones. Keywords: Pelletising feed, specific surface area, Blaine air permeability, laser diffraction testing

Jan 1, 2020

By K. Eckert, A. E. Sommer, S. Heitkam

One highly relevant challenge in flotation is the recovery of fine particles. Due to their low inertia, these particles are mostly pushed aside by rising bubbles. Consequently, they typically exhibit low probability for bubble-particle collision and thus, a poor recovery rate. In this work, the trajectories of fine particles in the vicinity of rising bubbles were investigated. The measurements considered a chain of millimetric bubbles in a rectangular container filled with deionized water. The flow field near the bubbles was measured by tomographic particle image velocimetry (TPIV), employing fluorescent tracer particles of 33μm diameter. Subsequently, trajectories of larger particles and bubble-particle collision events are recorded with 4D particle tracking velocimetry using a high temporal and spatial resolution. The results reproduce the well-known collision of particles on the leading edge of a rising bubble. Additionally, collisions on the tailing edge were observed in cases with a low Stokes number. The TPIV results demonstrate, that the high turbulent kinetic energy in the bubble wake allows particles to divert from the fluid streamlines and collide with the tailing edge of the bubble. The tailing edge collision probability increases with the bubble Reynolds number and decreased particle inertia. Overall, the investigation shows that the collision of fine particles in the bubble wake should be considered for the development of further collision probability models. Furthermore, the importance of turbulence on the fine particle flotation was demonstrated. Keywords: 4D Particle tracking velocimetry (PTV), tomographic particle image velocimetry (TPIV), fine particle flotation, collision probability, bubble-particle interaction, wake induced collision

Jan 1, 2020

By F. Shi , D. Lay, C. Antonio

High Voltage Pulse (HVP) technology has the potential to transform traditional mineral processing practice in the mining industry. HVP pre-treatment has been shown to enable ore preconcentration, achieve ore pre-weakening and improve mineral liberation. In order to improve the efficiencies of these novel HVP applications, it is essential to understand how HVP operational factors affect ore breakage in HVP pre-treatment. A two-level fractional factorial experiment using two rock samples, a gold-copper ore and a basalt sample, was performed to determine which factors have statistically significant influences on breakage probability, size reduction, and energy efficiency, and which factors have insignificant influences. Operational factors investigated include applied voltage, electrode gap, number of pulse discharges, the number of rocks being processed per batch, and rock size. In total, 1920 batch tests were conducted. For ore breakage characterised in terms of breakage probability and the degree of size reduction during HVP pre-treatment, the dominant factors were identified to be the number of pulse discharges, voltage, and the number of particles present in the processing zone. As all these three factors are related to the specific energy, it is concluded that the specific energy is the most important factor controlling ore breakage in HVP treatment. In terms of the efficiency by which spark energy is transferred from the generator energy, the factors found to have the most dominating influence were the particle size, the number of rock particles present in the processing zone and the voltage. Increasing the values of these factors reduced the loss of HVP energy during the energy transfer process. The factorial experiment using the two ore samples with vastly different mineralisation produced similar results. This proves that the dominant factors affecting HVP breakage are generally applicable to different ores types. Keywords: High voltage pulse, ore breakage, factorial experiment, specific energy

Jan 1, 2020

By C. Hartford, T. Holmes

Bulk-solids handling systems are often the most over-looked component and thereby weakest links in a processing plant’s value chain. Since their performance can dictate that of the entire operation, they actually deserve special attention. When designing a liquid handling plant, density and viscosity are well known and commonly used as design parameters. Bulk solids however, differ. While the design process is similar, the relevant parameters in handling bulk solids are instead friction, cohesive strength, compressibility, and permeability. These then vary depending on the mineralogy, particle size distribution and shape, moisture content, storage time-at-rest, temperature, and consolidation pressure. With so many variables, it becomes important to characterize each individual bulk solid across the full range of representative process conditions within the handling system, plant wide – or if you are not very lucky, suffer the consequences of poor material flow. Measuring flow properties and applying them correctly in bulk solid handling system design reduces project risk, saves significant capital, and drastically increases throughput, especially when done in the early stages of a project. Keywords: Flow Properties, Bulk Solids, Process Conditions, System Design

Jan 1, 2020

By A. Lebedev

Application of dynamic simulation for a base metal processing plant is discussed. The plant receives ore of variable quality from two pits and blending had to be applied to maximise recovery. The plant employs multiple stage crushing, screening, dense media separation, two-stage milling, flotation and further filtration. Stockpiles and bunkers are used in the plant to cater for breakdowns and operating delays, the latter being appropriately incorporated in the model. A detail dynamic simulation model was constructed from the rock face to the filtration plant to assist the plant design, notably with definition of the ore blending method, sizing storage capacity and in-plant conveyors. The plant model was broken down to capital equipment items and various feed types and mass balances were tested to ensure that the production target is met. The dynamic simulation tested the proposed blending method, identified bottlenecks, produced risk profiles for all strategic storage facilities and overall helped minimise the project risks and improve confidence in the plant design. Keywords: Dynamic simulation, ore grade, blending, capacity, risk profile, throughput, utilisation

Jan 1, 2020

By U. König, N. Norberg

Ore mineralogy defines the properties during processing and metal extraction. Fast and frequent monitoring of the mineral content and related process parameters brings value to the mining operation and material processing. Decreasing ore qualities and increasing prices for raw materials require a better control of processed ore and a more efficient use of energy. Traditionally quality control in mining industries has relied on time consuming wet chemistry or the analysis of the elemental composition. The mineralogy that defines the physical properties is often monitored infrequently, if at all. The use of highspeed detectors has turned X-ray diffraction (XRD) into an important tool for fast and accurate process control. XRD data and their interpretation make the difference in the identification of minerals, in describing their distribution in ore bodies and in their beneficiation during processing. The use of statistical techniques such as Partial Least-Squares Regression (PLSR) or Principal Component Analysis (PCA) on XRD raw data has been successfully trialled to determine raw materials and processed ores, in addition to well established methods for mineral identification and quantification. PLSR can be used to correlate process parameters directly from the XRD pattern without investigating the mineral content. Hidden information present in the XRD pattern but not determined with traditional methods can be used to improve the characterisation of the analysed materials. The practical use for the direct determination of process relevant parameters during exploration and ore beneficiation will be illustrated in several case studies from mining and ore processing. Keywords: Geometallurgy, mineral monitoring, X-ray diffraction, process efficiency

Jan 1, 2020

By S. Mohanty, K. Sarangi, S. Dash, P. P. Patra

Industrial effluent from various industries contains heavy metals that are a serious threat to humans, flora and fauna in water bodies, and the environment. The heavy metals are dumped after precipitation, which has serious environmental consequences. In this paper, a 2D axi-symmetry CFD model has been developed to study the extraction of chromium ion from industrial effluent, in a hollow fibre membrane, using Alamine 336 as the carrier and kerosene as the diluent. The Navier Stokes equation was used to predict the velocity profile of the aqueous and organic phases, and species transport equation, which considers both convective and diffusive mass transfer, was used to predict the concentration profile of the chromium ion in the computational domain. The distribution coefficient was experimentally determined at a pH 4, which was found to be the optimum pH. Numerical simulations were performed considering 11.11 mol/m3 of initial feed concentration for chromium ions and extractant concentration of 0.2 M. Simulations were carried out with various aqueous and organic flow rates, and validated with experimental data. Keywords: CFD, metal extraction, hollow fibre membrane, heavy metals

Jan 1, 2020

By W. Guiye, L. Chongjun, L. Huinan, Z. Yangge, H. Long

The current application of copper-molybdenum (Cu-Mo) separation inhibitors is often associated with large dosage, high toxicity, environmental pollution problems. In order to solve these problems, a light sensitive Cu-Mo separation inhibitor LS（light sensitive inhibitor，abbreviated to LS） was developed. In this paper, inhibitory performance, photodegradation rule, and acting mechanism of LS were studied. The subsequent test results showed that, compared with traditional inhibitors, LS has shown comparative advantages, with lower dosage and good inhibiting effect. A series of flotation tests with LS as inhibitor were conducted on a Cu-Mo concentrate. A locked-cycle test showed that a molybdenum concentrate containing Mo 49.88% and Cu 0.6%, with 93.23% molybdenum recovery and a copper concentrate containing Cu 29.92%, with 99.99% copper recovery can be obtained. The photodegradation performance of the reagent was investigated under 365 nm, 254 nm and sunlight irradiation. The degradation of the reagents could be completely achieved by irradiation of three wavelengths of light. However, with the different wavelength of irradiation light, the degradation rate is different, the time required to reach 50% degradation rate being 3 h (254nm), 4 h (solar light) and 6 h (365nm) respectively. The inhibition mechanism on chalcopyrite was studied. FTIR study showed that LS could be adsorbed on the surface of chalcopyrite by chemical adsorption, which could enhance the hydrophilicity of chalcopyrite. Ultraviolet adsorption tests indicated that the adsorption capacity of LS on chalcopyrite surface was greatly affected by pulp pH value, and the proper pH value was 5-9. Keywords: Copper-molybdenum separation, Inhibitor, Light-sensitive, Photodegradation, Mechanism.

Jan 1, 2020

By H. Zhong, S. Wang, Q. Sun

The flotation performance of 2-(benzylthio)-acetohydroxamic acid (BTHA) to diaspore was first evaluated by micro-flotation tests. The adsorption mechanism was further investigated through adsorption experiments, molecular dynamics simulation, zeta potential and X-ray photoelectron spectroscopy (XPS). The results demonstrated that BTHA had a stronger ability to collect diaspore in comparison with another diaspore collector, benzohydroxamic acid (BHA), especially under the condition of weak alkalinity, the flotation recovery can reach 90%. The more negative interaction energy (ΔE) between BTHA and diaspore from molecular dynamics simulation results revealed that BTHA had an easier adsorption ablity onto diaspore than BHA, which matched with adsorption results. The zeta potential and XPS revealed that Al atoms might bond with -C(=O)NHOH by formation of Al-O bonds. Keywords: Diaspore, flotation; adsorption; 2-(benzylthio)-acetohydroxamic acid

Jan 1, 2020

By L. Gutierrez, R. Yepsena

Enargite in porphyry copper deposits is an important mineral as it displays good floatability under the presence of the collectors usually used in the flotation of copper sulfides. As a result, copper concentrates grades are reduced. As scarcity of water resources is a problem relevant to Chilean mining, the use of seawater is a feasible solution. The behaviour of copper sulfides and molybdenite in the process of flotation in seawater was previously studied but not for enargite. The objective of this research is to study the behaviour of the enargite in different conditions of electrochemical potential during the process of flotation using seawater. The study was carried through micro-flotation tests using pure samples of enargite, at Eh values ranging from -300 to 500 mV(SHE), both in seawater and aqueous solutions containing calcium and magnesium. The results show that at pH 10.5 in seawater, the enargite and chalcopyrite recoveries are reduced throughout the whole range of Eh studied. At pH 9 in seawater, enargite and chalcopyrite are depressed under reducing and slightly oxidising conditions. The recovery of both minerals drastically decreases at Eh values lower than -100 mV and greater than 400 mV. The behaviour of enargite in seawater flotation differs from that observed in conventional water, since in the latter case the recovery of enargite decreases at higher potentials close to 500 mV. Keywords: Enargite, flotation, seawater, redox potential

Jan 1, 2020

By V. A. Myazin, M. V. Korneykova, A. V. Svetlov, V. G. Minenko, D. V. Makarov, A. L. Samusev

The paper discusses the treatment problem of mine (waste) water for enterprises of the Russian Arctic. The wide range of relevant pollutants, financial resources, the availability of land for the construction of a treatment plant, waste generated during the treatment process are some of the factors controlling current and future process design solutions. All mining operations have adopted water treatment and water quality monitoring solutions, however there is no single approach to the problem and each industry participant operates within the scope of its available resources. The range of existing and emerging methods is extensive — from using constructed wetlands for the deposition of mineral nitrogen compounds in settling ponds, reagent deposition and chemical coagulation in exhausted mine workings, and filtering dams on the surface to retrofitting existing mine drainage treatment plants with the adoption of the electrochemical coagulation process. Methods of wastewater treatment from heavy metals, oil products, and nitrogen compounds are demonstrated in the example of two industrial facilities in the Murmansk region. It was found that the use of electrochemical coagulation provides effective treatment of mine water from NO3, NO2, Ni, Fetotal and petroleum hydrocarbons (the degree of purification from 50.5-99.7%), the use of phytotreatment system provides wastewater treatment from ammonium ions and nitrite ions by 53-84%, nitrate ions - by 22%. Keywords: Industrial water treatment, treatment flowcharts, settling ponds, constructed wetlands, reagent sedimentation, chemical coagulation, electrochemical coagulation

Jan 1, 2020

By M. Bryson, G. Marap, M. Ntlhane, M. D. Hlahane

This study investigated flotation of phosphate from a low-medium grade 8-12% P2O5, 65-73% SiO2 sedimentary phosphate ore from Kropz Elandsfontein (herein referred to as Elandsfontein) in South Africa. Quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) was used to determine apatite grain size distribution, liberation and mineral association in the F2 horizon sample. The mineralogy indicated that apatite was liberated and for the Elandsfontein plant to operate at the design throughput, the flotation feed has to be milled to a coarse grind ranging between 300 μm and 425 μm. Reverse flotation process routes using varying reagent dosages, and flotation feed top sizes that could possibly yield a final product of 31% P2O5,10% SiO2 at a reasonable +70% P2O5 recovery were investigated. Based on the results, a split circuit of coarse (-300+212μm) flotation and fine (-212+20μm) flotation, was mostly preferred as compared to treating the whole ore. A final combined concentrate of 31% P2O5 and 10% SiO2 with P2O5 recovery of 84% could be produced from the reverse split circuit. The robustness of reverse flotation for both coarse and fine fractions was further investigated. Reverse flotation of the fines fraction was found to be robust and produced a final product of 31% P2O5. It was however more challenging to achieve the required product grade and recoveries on the coarser fraction (-425+212μm), suggesting that reverse circuit was not adequately robust at fractions coarser than 300μm. Keywords: Phosphate, sedimentary, reverse flotation, particle size

Jan 1, 2020

By J. -M. Milazzo, T. Wallmach, S. B. Blancher, A. Amalric

In a FeNi electric arc furnace, the physical properties of the slag (chemistry, viscosity, liquid/solid/gas ratio) are of crucial importance in controlling the efficiency of the process. In this paper, we studied the slag crystallised on the walls of a semi-industrial furnace (freeze-lining), the slag rising through the burden during foaming phenomena, and the casted slag. The freeze-lining is the layer of oxides that crystallises on the refractory wall of a furnace, protecting it from chemical and mechanical aggression. It records changes in furnace conditions (slag chemistry, temperature, oxygen fugacity), which makes it possible to observe the impact of these elements. In the high reduction test, the freezing lining is composed of magnesian olivine. Switching to a low reduction process increases the Fe content of the olivine and causes orthopyroxene to appear, making the freeze-lining mechanically and thermally weak. Thermal incidents in the furnace cause significant slag foaming. This foaming is produced by a massive crystallisation of the olivine (due to the drop in temperature), and inducing an exponential increase in viscosity, preventing the free circulation of gases. These foaming episodes are also recorded in the freeze lining and form layers rich in gas bubbles, and therefore mechanically fragile. The slag casted and cooled in a ladle allows the first steps of slag crystallisation to be studied. Olivine is the liquidus phase, with a magnesium-rich core and an iron-enriched rim, contemporaneous with the orthopyroxene phase. The habitus of these phases is very similar to that found in komatiites for the same minerals. FeNi slag is therefore an industrial analogue that is easy to study and compare to komatiites. Keywords: Pyrometallurgy, ferronickel, slag, freeze-lining, characterisation, olivine, mineralogy

Jan 1, 2020

By G. D. Rosales, P. F. A. Braga, S. C. A. França, C. P. Pinto

The growing market demand for lithium is mainly due to its use in the manufacture of batteries for electric or hybrid vehicles and portable equipment (smartphones, tablets, power tools, notebooks, etc.). Currently there is great interest in finding new sources of lithium and technologies for its utilisation. Li-S batteries have received attention due to their theoretically high specific energy density, which is 3 to 5 times greater than that of Li-ion batteries. Unlike Li-ion batteries, of which the main raw materials are lithium carbonate and lithium hydroxide, the main raw material for Li-S batteries is lithium chloride. The anode used in Li-S batteries is metallic lithium, produced by a molten lithium chloride electrolysis process. The extraction of lithium from pegmatites such as spodumene, previously abandoned in the 1990s for being uneconomical, has become attractive due to the increase in prices as well as the need for greater lithium purity of products made from lithium-bearing minerals. The main methods used for lithium recovery from spodumene ore include the sulfuric acid process, the alkaline process (lime or limestone as raw material) and the chlorination roasting process. Thermodynamic modelling using HSC software 5.1 was conducted to predict different reactions that could occur during chlorination roasting of the spodumene/MgCl2+CaCl2 system. Lithium extraction from the solid obtained after the chlorination roasting was also investigated. The results of thermodynamic analysis provided a better understanding of the chlorination roasting process for lithium extraction. Metallurgical tests with a mass ratio of 1:6 (spodumene:chlorides) and molar ratio of 2:1 (MgCl2:CaCl2) allowed over 95% recovery of the lithium contained in the spodumene concentrate. Keywords: Spodumene, lithium chloride, chlorination roasting

Jan 1, 2020

By A. Chryssoulis, D. Venter, R. Dunne

An often-overlooked parameter of flotation processing is the impact of surface chemistry. Flotation processing, being a heterogenous process is largely reliant upon the chemistry occurring at the interfaces between solid-liquid phases. Development of analytical techniques such as Auger electron spectroscopy, X-Ray photoelectron spectroscopy (XPS) and low energy electron diffractions (LEEDS) has allowed for a dynamic view characterizing surface composition and structures. The advent of ‘static’ systems, capable of measuring ultra-thin layers on surfaces at low concentrations, was the next step in surface analytical developments. In general, it is the low concentrations and fragmentation patterns which limit the analysis of certain chemical species at plant concentration ranges. At present, analysis of inorganic and organic surface modifiers by time of flight mass spectrometers with a variety of ionization techniques has become a common analytical method to measure chemical species on the outermost surface of mineral particles. By studying the relationship between surface analysis results with metallurgical outcomes, the implications of the presence of surface species can be determined. The presence of flotation activators or depressants can be established using Laser Ionization Mass Spectrometry (LIMS) and Resonant Ionization Mass Spectrometry (RIMS) which are highly versatile surface sensitive analytical techniques. A case study applied to sphalerite flotation in the Neves Corvo Cu-Pb-Zn concentrator and the implication inorganic surface modifiers have is presented. By determining the relative concentrations of Cu, Pb, oxidation products, Ca and other surface species in floated and rejected mineral particles, rationale for improving recovery and selectivity is elucidated. Keywords: Cu-Pb-Zn Flotation, Process Mineralogy, Surface Chemistry, Flotation kinetics

Jan 1, 2020

By T. H. Yang, Q. K. Wang, T. Song, J. W. Zhou

The grinding circuit can be one of the most important mineral processing circuits in plants. Along with the application of large-scale milling machines, the design and optimisation of the operation strategy for grinding circuits is more complicated. An in-house grinding process simulation tool was developed to mass balance, model fit and simulate crushing, grinding and classification circuits. An industrial grinding and classification circuit in a copper mine was modelled, and the modelling parameters were verified by a particular group of plant survey data. To justify the prediction ability of the fitted models, the model predictions under different operation conditions were compared with another group of plant survey data. Then the model predicted the effects on the circuit of changing operating conditions. Circuit analysis of the comminution process for water feed to a SAG mill, water feed to sump, the rolling speed of a SAG mill and the percentage of ball filling in a SAG mill was put into practise, based on the simulation results. The simulation results can be used to help plant operators understand the features of the comminution process and may help to build a knowledge library for process control. Keywords: Process modelling, grinding, comminution, circuit analysis

Jan 1, 2020

By S. Soren, K. Deo Mehta, G. Jha

The paper aims to find a sustainable sintering process through cleaner means, in order to achieve the desired outputs with zero environmental impact. At present, sintering has no control over its environmental impacts. These impacts occur when fossil fuels such as coal and coke are used in metallurgical sintering. These fossil fuels are undoubtedly effective in their assigned reducing task, but simultaneously emit about 220 kg of GHGs (greenhouse gases) per tonne of sinter produced. The current attempt has focused on reducing these emission levels by switching from coke to a renewable fuel source such as biomass. Biomass is a cleaner fuel source with a significantly lower emission footprint compared to coke. In the experimental campaign, sawdust and wood-charcoal were used in substitution for coke. Experiments were designed in a progressing substitution to obtain the maximum substitution ability without compromising the sinter properties. Sawdust as raw biomass source optimally substituted 10% of coke. The substitution levels were remarkably higher (30%) for wood charcoal due to its low moisture and high calorific values. A fuel blend with 30% biomass and remaining coke succeeded in producing a sinter with acceptable quality indices. Sinters prepared with or without biomass contribution shared an identical phase transformation and microstructures. In order to to maintain consistency in the process, every effort was made to maintain all operational and process parameters identically, except for the fuelling framework. Keywords: Sintering, sustainable, biomass, GHGs, fuel substitution

Jan 1, 2020