Search Documents

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling both dust and gas. Redirecting all the air towards the face equally up both sides of the machine increased both the dust and gas concentrations around the machine. When all the air was redirected towards the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all the scrubber exhaust was redirected towards the face either up the off-tubing side or equally up both sides of the mining machine.

Feb 23, 2014

By P. Zhang

A 1989 FIPR characterization study of the future phosphate resources in Florida showed that MgO would be a problem with both the pebble and concentrate as phosphate mining moves deeper. Since the ratio of concentrate to pebble will become higher and higher in the future, reducing Mg content in the concentrate by a small margin would allow blending of a large portion of the high-dolomite pebble. This research was conducted based on that logic. The following six approaches were tested for reducing MgO content in the flotation concentrate: (1) Adding a dolomite depressant in the rougher flotation step; (2) Dolomite flotation on the rougher concentrate with and without grinding; (3) Dolomite flotation on the cleaner concentrate with and without grinding; (4) Scrubbing the flotation feed; (5) Scrubbing the rougher concentrate; (6) Scrubbing the cleaner concentrate. Successful methods include adding a dolomite depressant in the rougher flotation, dolomite flotation on the cleaner concentrate with grinding, and scrubbing the cleaner concentrate in quartz sand. These techniques could reduce MgO content in the final concentrate by 20-40%. The flotation process could achieve a concentrate with the lowest MgO content, but it is the most expensive approach. Adding a dolomite is inexpensive and easy, but the effect is limited. Overall, scrubbing may be the most promising technology for this purpose.

Feb 23, 2014

By B. Goertz

Since the turn of the century the mining industry in the United States has had a number of serious mine explosions, fires and ground fall disasters that have led to a major re-evaluation of mine communication and rescue practices. One of the hindrances of current underground communication technologies is the potential of lost or cut connections when a serious accident, such as an explosion, fire, inundation or major ground fall, takes place. The Mine Improvement and New Emergency Response Act of 2006 (MINER Act)1 mandated that each underground coal mine in the U.S. must provide for two-way wireless, post-accident communications between underground and surface personnel as well as electronic tracking of underground workers One area that has gained renewed attention in the mining sector is Through-The-Earth (TTE) communication. TTE technology has a major advantage in that transceiver devices can be carried by miners and set up quickly during an emergency, since they require no wire connection to the surface. TTE technology uses ultra-low frequency (1 to 4 kHz) electromagnetic waves, requiring relatively large wire loop antennas and highly sensitive receivers. The signal bandwidth is narrow and the permissible antenna currents in coal mines are restricted, which has led to limited usability of TTE technology in the past, as evidenced in research studies conducted by the U.S. Bureau of Mines in the 1970s. Yenchek (2012)2 pointed out that recent advances in receiver and signal processing technology have enabled voice and text communication capabilities and much improved sensitivity that offers new possibilities for TTE communication in mining applications. One company that has been developing such technology is Vital Alert Communication Inc. Vital Alert has been providing TTE communications since 2003 with a growing focus on emergency response and portable systems. The company?s Canary® Go System is one such product that looks to provide reliable communication capabilities in a portable, user friendly unit that can be utilized both for normal operation and mine rescue scenarios. Researchers at the Colorado School of Mines (CSM) have tested the Canary Go TTE communications system in the CSM Edgar Experimental Mine to determine signal propagation distances, signal quality and aspects of practical application.

Feb 23, 2014

By S. Iverson

Fall of ground accidents continue to be a source of injury in underground metal mines. MSHA accident statistics indicate that most rock fall accidents occur at a new face where drilling and blasting methods are used. Removing loose rock by scaling is imperative to removing the potential for rock fall injury. Detection of potentially loose rock could improve the scaling process and result in fewer rock falls. Infrared thermal imaging cameras were investigated as far back as 1966 as a tool for loose rock detection. Early on it was clear that sensitivity (e.g. detectable temperature increment) is a key factor in this application. Both pixel resolution and temperature resolution have greatly improved with modern instruments. This paper describes an evaluation of modern infrared thermal imaging camera technology to detect loose rock conditions at six underground metal mines in the western U.S. It was found that thermal images provide a high resolution visual discrimination between loose rock and intact rock. However, detecting loose rock was difficult in cases where the rock and ventilation air were at the same temperature. Loose rock was detected when rock was both warmer and cooler than the ventilation air temperature. Warm rock with cool ventilation air provided the best conditions for detection.

Feb 23, 2014

By R. Adsero

The volume of data produced by operating mines has increased substantially over the last 10 years. However, the volume of data and analytical capability has been negatively correlated to equipment productivity for at least the last seven years. In simple terms, as the volume of data has increased equipment performance has declined. Table (2010) tells us that ?The calamity of the information age is that the toxicity of data increases much faster than its benefits?. More data does not guarantee improving productivity; but more data is also not the cause of declining productivity. Similarly, when equipment performance does start to improve, (it must ? there really is no option if mines want to remain competitive), it will not be the data nor analytics which causes it; it will be the people using the resources at their disposal; including the data. Data and analytics can help if the toxicity of the data can be managed. The simplest form of business improvement using data is benchmarking. The objective of benchmarking is to understand and evaluate the current position of a process in relation to ?best practice? and to identify areas and means of performance improvement. The application of benchmarking involves four key steps: (1) Analyze and understand in detail existing processes; (2) Analyze and understand the processes of others; (3) Compare your own performance with that of the others analyzed; and (4) Design and implement the changes necessary to close the performance gap(s). There are however, many in the mining industries who have shunned equipment benchmarking because they believe that, ?every mine is a pilot?. In other words, the differences between mine operations make comparisons between them of little value. This paper will present a valid approach to benchmarking equipment performance and reliability, accounting for the differences and similarities between operations, producing a result which can be used to add value to mines around the world.

Feb 23, 2014

By F. Habashi

The peninsula that lies between the Black and Mediterranean seas, called Asia Minor by the Romans and Anatolia by the Greeks, was one of the crossroads of ancient civilizations. The fall of Constantinople in 1453 was a turning point in the history of mankind. Visits to Istanbul, Ankara, Eskisehir, Cappadocia, and Trabzon will be given together with the history of the country. Mineral resources of the country will also be briefly outlined.

Feb 23, 2014

By C. Sun

With complex component, higher salt content, low biodegradability, DSD acid oxidation wastewater could not be efficiently dealt with traditional methods. It is pointed that the coal water slurry could be made with DSD acid oxidation wastewater of different concentration and the density of coal water slurry could be up to 70%, while its viscosity is only 850~930 mPa?s. The coal water slurry could be perfectly jetted and burnt under different conditions. The higher density the DSD acid oxidation wastewater has, the better properties the coal water slurry have. The pollution components and characteristic group of DSD acid oxidation wastewater are similar to the additives of coal water slurry, so it could be used as a kind of usable additive of water coal slurry. It is so reasonable and feasible to make coal water slurry with DSD acid oxidation wastewater that the pollution of DSD acid oxidation wastewater can be solved completely.

Feb 23, 2014

By A. J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of steel wire ropes. Steel wire ropes are very suitable for mine hoisting due to their high strength and durability, but have the negative characteristic of a low strength/weight ratio. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength/weight ratio of synthetic ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application.

Feb 23, 2014

By B. A. Ashley

In 2007, Rosebud Mining Company (RMC) opted to extend the reserve base of Tracy Lynne Mine by developing through a sandstone channel. The extension provided access to approximately 6 million additional recoverable tons (approximately 8 years of mining) which originally had been deemed inaccessible. An evaluation of the mine?s existing ventilation system, which was designed to meet the needs of the original limited reserve, concluded that two ventilation shafts would likely be required to adequately ventilate the projected workings in the expanded reserve. To assist in the evaluation, a ventilation model of the mine was developed using Ohio Automation?s ?ICAMPS MineVent? software based on field data from Tracy Lynne Mine, prior ventilation survey experience at similar RMC mines, and relevant published sources. Model results suggested that the most economical shafts would be an 8-ft diameter return and a 4-ft diameter intake. Unfortunately, issues related to property leasing and shaft site permitting caused construction delays. Therefore, the model was also used and proved to be effective in prioritizing interim ventilation upgrades which could be implemented in order to maintain coal production. Model results indicated that the best interim upgrades included rehabilitating restricted entries and damaged stoppings and replacing the main fan with a higher pressure fan. From late 2010 to mid-2012, all interim upgrades and shafts were implemented. Current models and mine experience indicate that ventilation will not be the limiting factor for mining the additional reserve.

Feb 23, 2014

By J. T. Winkelmann

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately twenty miles northwest of Kingman, Arizona. The concentrating facility has been regarded, with the expansion in 2011, as a plant capable of treating fifty thousand short tons of feed per day for the mixture of supergene and hypogene ores available. The grinding circuit consists of two 32? x 14? SAG mills and four 20? x 28? ball mills. As ores became harder with greater depth in the adjacent pit areas, however, the SAG mills became severely throughput limited. The traditional treatment for similar properties is the installation of a recycle pebble crushing circuit. Because the cost of such an installation is quite elevated, and preliminary testing and research was inconclusive regarding the predicted throughput increases, management and technical personnel set out to find another solution to the problem. The result entailed a redesign of SAG lifters/liners and a nearly unique circuit change which was, at best, a difficult step that defied current grinding logic. This paper describes these changes, events leading up to them, and the results.

Feb 23, 2014

By E. Lee

The behavior of As bioleaching using Acidithiobacillus thiooxidans (A. thiooxidans) in mine tailings containing highly concentrated As contents (i.e., As=33877 mg/kg) was systematically evaluated according to the changes in temperature (25?40°C, pulp density=0.5%, pH=1.8), pulp density (0.5?4%, temp=30°C, pH=1.8), and initial pH(1.8?2.2, temp=30°C, pulp density=0.5%). The changes in temperature and pulp density affected the As leaching behavior more than the change in initial pH did. Based on the pH and oxidation-reduction potential (ORP) results, the As leaching was attributed to solution acidification. In particular, As leaching was accelerated with increasing sulfate production in the reacting solution. After bioleaching, surface of tailings examined that many pores which dissolved As were formed by a chemical reaction due to bacteria. The As bioleaching efficiency by A. thiooxidans was enhanced by the oxidation of both the added elemental sulfur and the sulfur compounds in the mine tailings. The As bioleaching efficiency was maximized at 50.5% under conditions of an initial pH of 2.2, reaction temperature of 30°C, and pulp density of 0.5%.

Feb 23, 2014

By R. C. Gilmore

Computational fluid dynamics (CFD) has been used to model gas compositions in underground longwall coal mine gobs to study oxygen ingress and the development of potentially explosive methane-air mixtures that may form in the gob. The scenarios studied involve various headgate and tailgate ventilation and inertization schemes and controls. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at Colorado School of Mines have used an innovative meshing approach, allowing easy adaptation of the CFD model to adjust to a variety of bleeder and bleederless mining geometries, with gob porosity and permeability scalable over a wide range. This paper presents the methodology of the meshing and scaling approach along with recommendations for using CFD modeling in longwall gob ventilation applications. The new meshing technique was utilized to evaluate the function of a back return in a progressively sealed gob. The back return was successful in maintaining sufficient oxygen concentrations in the tailgate corner of the longwall face.

Feb 23, 2014

By T. Bui

The shut-off value for a panel cave mine determines when a draw point will be shut-off and mining will cease from that draw point. Using a shut-off value strategy for a panel cave mine is similar to using a cut-off value strategy for an open-pit mine. This paper will discuss how to choose an appropriate shut-off value strategy that an engineer can use when planning a panel cave mine to increase the net present value (NPV) of the project. Using a shut-off value equal to the mining and processing cost will provide the total mining reserves for a panel cave mine given a specified footprint. When the net present value analysis method is used to compare one design to another then using a shut-off value greater than the mining and processing cost will generate a higher NPV. This strategy will replace the marginal ore at the top of a draw column with higher grade ore at the bottom of newly opened draw points. A draw column is broken material which sits above a draw point and it is mined to a specified height above the draw point. This height is called the height of draw (HOD). Varying the shut-off value over the life of the mine can increase the NPV even further. This strategy would have a high shut-off value during the early stages of a mine and low shut-off value during the later stages. If the shut-off value is too high then too many tonnes would be left behind the draw point and the overall value of the mine will be decreased. Also with a high shut-off value then the production target may not be maintained due to too many draw points closing too soon.

Feb 23, 2014

By J. Duran

Mining at Phoenix is currently done by surface operation in the Fortitude and Bonanza Pits, at a combined rate of approximately 110,000 tons per day. A portion of the ore bodies targeted by these pits was mined previously by underground mining methods, dating back to the mid to late 1800?s. Most of the underground workings (voids) are located in the west central area of the Bonanza Pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This paper presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

Feb 23, 2014

By A. Moharana

A massive slide at Bingham Canyon wiped out a side of the pit and covered the main haul road in and out of the pit. All pre-slide mine designs and schedules were no longer valid. New designs and schedules needed to be developed quickly to provide management with information regarding the immediate post-slide production potential and the time needed to ramp back up to full production. At the time of the slide, an effort was already underway to convert Bingham?s in-house Medium Term Scheduling Process to MineSight®?s Schedule Optimizer (MSSO). One of the main reasons for doing this was to reduce the time needed to produce Medium Term Schedules at Bingham, which involves a complex shovel-based scheduling approach with shovel productivities based on shovel type and the types of mining cuts to which the shovel is assigned over each planning period. The objective of the schedule was to maximize shovel usage, satisfy mill feed requirements of four SAG mills with variable milling rates, and have flexibility in setting truck constraints. This paper will describe how the new MSSO-based mine scheduling process met the challenge of producing new schedules for Bingham in a minimal amount of time.

Feb 23, 2014

By J. Choi

For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50?200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.

Feb 23, 2014

By K. Lang

A test section of the upper most lift and underlying lifts of a large scale copper heap leach operation was instrumented and monitored with advanced wireline geophysics, fiber optics and resistivity electrode arrays. Elemental Capture Spectroscopy (ESC) copper measurements, resistivity measurements from an Array Induction Tool (AIT), electrical resistivity tomography (ERT) and distributed temperature sensing (DTS) with fiber optics provided integrated near real time data about the performance of the heap. During the leaching cycle, ECS provided continuous vertical measurements of copper in the upper most and underlying lifts in the test section of the heap and was used to generate a copper recovery curve. ERT inversion modeling provided high resolution 3D resistivity measurements, which were used to evaluate moisture distribution. DTS measurements of temperature were used to track the PLS front and calculate velocity. AIT induction provided highly precise bulk resistivity measurements. In-situ samplers provided PLS chemistry at multiple points. Properly integrated monitoring data can provide the heap leach operator with information that can be used to evaluate the hydrodynamics and metallurgy of the leaching process in near real time. Problems in the heap, such as pooling, channeling, longer lag and breakthrough times, excess acid consumption, increased solution in inventory, toe saturation and slope stability can be detected in near real time with the in-situ measurements evaluated.

Feb 23, 2014

By S. H. Brown

In our work as health physicists*, we do a lot of public speaking and interaction with the public on issues related to development of uranium mining and milling (?uranium recovery?) in the US. Understandingly, the public has important concerns about this. Accordingly, this paper is presented in a ?question and answer? format in which we have tried to capture what are some of the most common concerns we hear from citizens and address them. We have attempted to do so based on the best scientific information we have, representing information well documented in peer-reviewed scientific literature and consensus positions from both national and international scientific standard setting bodies and related committees. We have included some of the more important of these scientifically-based references to support the information provided. Practical space limitations prevent completeness in this regard in some cases. Visit the Health Physics Society?s web site or feel free to contact me directly for additional references, information or detail ? Steve Brown. The health physicist?s primary objective is to manage the beneficial uses of ionizing radiation while protecting workers and the public from potential hazards. For more information on what a health physicist is and on the Health Physics Society, visit the Society?s web site at www.hps.org.

Feb 23, 2014

By Luttrell. G.

The profitability of coal mining operations is highly dependent on the performance of the coal blending and processing facilities. Many companies have recognized this fact and have instituted optimization programs that require large amounts of coal characterization data, extensive operational information and complex costing models. Unfortunately, this brute force approach to optimization is often overwhelming in terms of time and cost and is generally too inaccurate to be of value in day-to-day field operations. A simpler and more practical approach involves the use of ?micro-price? optimization throughout the coal supply chain. This fundamental concept assigns unit values to each type product (particle or groups of particles) passing through the production units. True optimization occurs whenever all particles with positive worth are recovered and passed to market, while all particles with negative worth are rejected. This paper describes the fundamental workings of the micro-price concept as applied to coal blending and processing operations. Several examples are also included to demonstrate the economic gains that can be realized via the application of this concept.

Feb 23, 2014

By J. A. Organiscak

Enclosed cab filtration systems are typically used on mobile mining equipment to reduce miners? exposure to airborne dusts and diesel particulates generated during mining operations. Various filter configurations can be used within the heating, ventilation, and air conditioning (HVAC) systems of cabs to remove the airborne contaminants. The air cleaning performance of cab filtration systems is highly dependent on the efficiency of the air filters, the number of filters used, and their placement within the HVAC system. This paper shows how to mathematically model cab filtration systems and illustrates a methodology for developing other cab filtration system design models. Node diagrams of several filtration system circuits are illustrated with their mathematical models at steady state airflow and concentration conditions. Laboratory and field data are presented to demonstrate the validity and utility of modeling enclosed cab air cleaning performance. The paper concludes that incorporating multiple filters throughout the HVAC system improves the air cleaning performance and robustness of the cab filtration system design.

Feb 23, 2014