Search Documents

By R. Gensemer

A number of state and federal agencies are calling for development of aquatic life criteria for conductivity. These aquatic life criteria or ?benchmarks? are based on observed correlations between conductivity and benthic macroinvertebrate community composition, generally measured by composite metrics or indices. However, development of an aquatic life criterion for a composite variable like conductivity is made difficult by a number of factors. Based on a database from West Virginia, observed patterns of invertebrate community composition versus conductivity may instead be related to a combination of abiotic (e.g., ionic composition, habitat) and biotic (e.g., life history, colonization potential) factors. Many benthic invertebrate taxa also do not respond to increasing conductivity in a consistent relationship. Many states have determined that a composite variable, like conductivity or TDS, is not appropriate for criteria development, as many studies have shown that toxicity varies as a function of ion composition and can be mitigated by elevated hardness. We conclude that the relationships between conductivity and changes in benthic macroinvertebrate community composition are neither strong nor reliable enough to warrant derivation of a criterion based solely on conductivity.

Jan 1, 2011

By K. R. Griffin

Explosions in underground coal mines have been a serious safety concern since the advent of mining; despite significant technological advances, they are still occurring. Parameters such as barometric pressure, geological changes, and changes in ventilation can contribute to an explosion. These factors can be monitored with available and developing technologies to create algorithms that predict when explosions are more likely to occur. This paper reviews current underground atmospheric monitoring systems and related regulations around the world. In addition, suggestions for improvement and implications for explosion prevention are discussed.

Jan 1, 2011

By Bill Dershowitz

Consider a deep gold orebody with grade of 4 g/t (0.11 oz/st). At the time of this writing, with gold prices at historic highs, it could be a good, but not great, prospect. But if it is a vein deposit, and those veins are 200 g/t (5.8 oz/st), it would be significantly more attractive if there was a way to produce directly from those veins, leaving the rest of the rock in place. [Figure 1 The red around each of the four injector wells shows areas of high pressure, where the lixiviant fluid is pumped into the rock mass, with orange and yellow indicating dissipated pressure. The black lines indicate some of the fracture pathways through which the lixiviant, with absorbed metal, flows toward the central recovery well where low pressure is indicated in blue. Lixiviant is pumped out through the recovery well. Image courtesy of Golder Associates.] There is a way to do this, in situ leach (ISL) or solution mining. It has been a viable commercial technology for more than five decades.

Jan 1, 2011

In late November 2010, a Laotian landmark was achieved for the country?s first tunnel boring machine - (TBM) driven tunnel. Italian contractor CMC di Ravenna celebrated the breakthrough of a 7.6-m- (25.1-ft-) diameter Robbins single shield TBM for a hydroelectric tunnel on the Nam Theun River. The Theun Hinboun expansion project and 5.5 km (3.4 miles) headrace tunnel will bring much needed power in-creases to Laos and Thailand. . ?Since this is the country?s first machine, it has awakened people?s curiosity and interest. We had experienced Italian and Chinese crew members, but we also trained many Lao workers during the course of the project, as this was something they had not seen before,? said Luca Barbàra, Far East Manager for CMC di Ravenna. The machine broke through on Nov. 21 into an exit shaft close to the intake structure on the river. The machine is now being disassembled and removed - CMC hopes to use it on upcoming projects in the region. Due to the current rainy season and relative low level of the tunnel, the last 100 m (330 ft) up to the intake structure will be completed using drill-and-blast after the waters recede below the tunnel invert.

Jan 1, 2011

By G. Gaidajis, K. Angelakoglou

The development of a tool for assessing the environmental sustainability of mining facilities is described in this study. The tool is based on the analysis of basic components of the examined system, i.e., the quantities of the incoming materials and outgoing wastes, their hazardousness and scarcity, the utilization of water and energy resources, and the biodiversity. The developed tool provides both qualitative and quantitative assessment of the environmental performance of a mining facility in a broad time scales (past-present-future) and is easily applicable from non environmental experts. Moreover, relative software is developed to further support the application of the methodology. The implementation of the tool is expected to lead to an improved understanding of the environmental performance of a mining facility and more importantly identify the areas of significant environmental concern. However, based on feedback from industries, a number of shortcomings of the approach have been identified so far and are presented, indicating further actions for the advancement of the proposed tool.

Jan 1, 2011

By D. Gärtner, A. Oster

"""Operational excellence"" provides a sound foundation for RWE Power AG's three strategic pillars (innovation, expansion and organic growth). The maintenance and development of operational excellence in lignite mining operations at RWE Power is supported by the Continuous Improvement Process (CIP) ""immer:besser"" (getting better). Obtaining cost reductions with the aid of the CIP as a kind of value-adding self-renewal process to ensure competitive lignite mining operations and lignite-based electricity generation forms the basis for further increases in profitability and growth. Since the beginning of the 1990s, RWE Power has carried out a multitude of re-engineering projects focusing on the efficient shaping of processes with the assistance of external consultants to enable the Company to cope with the considerable need for change by swiftly implementing major efficiency levers. These also include the required adaptation and development of the organization. Since 2004, the Continuous Opencast Mine Improvement Process (""KVT"") has enabled the mines to tap significant cost reduction potential by virtue of their own strength. But there is another issue that has come into focus: the development of performance enhancement options. In 2006, the ""KVT"" process, piloted in the opencast mines, was included in the RWE Power-wide immer:besser (i:b) programme (Figure 1)."

Jan 1, 2011

By Stephen Liu

Tunnel excavation while mining is not often performed in North America primarily due to access constraints in both operations. Referencing European approaches for long distance tunneling, the Devil?s Slide Tunnel project has applied innovation and technology to provide the ability to overcome this unique challenge. The Devil?s Slide Tunnel requires the construction of twin bore tunnels excavated based on sequential excavation method (SEM) construction methods using New Austrian Tunneling Methods (NATM) principles. The twin tunnels are approximately 9 m (30 ft) in diameter and 1,250 m (4,100 linear ft) in length. The purpose of this project is to reroute Route 1 from around the Devil?s Slide through the San Pedro Mountains crossing from Montara, CA along the south and into Pacifica, CA in the north. The Caltrans project was awarded in December 2006 for a total of $272,366,000. The job is an A+B job, thus the estimate scheme of final lining while tunnel excavation is important to save time. A+B is a method of rewarding a contractor for completing a project as quickly as possible. By providing a cost each working day, the contract combines the cost to perform the work (A) with the cost of impact to the public (B) to provide the lowest cost to the public. Concurrent mining while lining is achieved through a series of gantries and a set of tunnel forms allowing the pass-through of the excavation equipment. The tunnel lining operation passes through several phases of work that are dependent upon the progress of the tunnel excavation process. This involves unique milestones, such as the evolution of the ventilation system, development of an enlarged cross passage to allow equipment to access each tunnel from within the tunnel and, finally, the installation of an invert prior to arch lining that limits the continuity of the final lining operation.

Jan 1, 2011

By D. Bogunovic

The objective of this research was to conduct field-scale experiments at an operating surface coal mine in order to determine the impact of the bucket fill factor on dragline production rate and energy consumption. Data collected from a dragline monitoring system were recorded in a specifically designed software tool and the relationship among these parameters was established. an algorithm for the determination of the ?best? fill factor was developed and integrated in the software. It was determined for the analyzed dragline in the mine that energy consumption in the digging phase can be reduced by 36% and production rate can be increased by 1.4% for a bucket fill factor of about 80%, a fill distance of 19.8 m (65 ft) (i.e., 3.1 bucket lengths) and a bucket fill time of 15 sec. the method developed and applied in this study may help dragline operators to determine the fill factor that will increase production rates and reduce energy consumption in specific surface coal mines. Mining Engineering, 2011, Vol. 63, No. 8, pp. 48-53. Official publication of the society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Steve Kral

San Francisco, CA will host about 1,500 tunneling and underground construction professionals from around the world during the biannual Rapid Excavation and Tunneling Conference (RETC), June 19-22. These professionals are gathering in a city that has seen much under-ground work throughout its history. And, today, the San Francisco region has more than $4.6-billion in tunneling projects under way. The RETC will include three-and-a-half days of technical programming, complete with proceedings, two short courses, two field trips and a host of social activities. In addition, the accompanying exhibit has attracted 127 exhibitors in 152 booths, an RETC record. The following is a brief list of activities that will take place during the conference. A more complete program is provided in the official showguide that is bound into this issue of Tunneling & Underground Construction.

Jan 1, 2011

By D. Pappas

Over the past decade the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry?s injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked, injury rate, and days lost. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992?2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent.

Jan 1, 2011

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

Stope width was controlled around 3.5 feet for the narrow high grade vein system at Hollister Gold Mine. Without top access, backfill material was pumped from bottom access up into stope through a series of pipes after ore had been slushed out in each mining cycle. Backfill material was changed from one layer of low strength concrete plus one layer of high strength concrete cap to one layer of low strength cellular concrete plus one layer of high strength concrete cap. Backfill cost was cut down to 30 percent during this process. To reduce the steel concrete pipe set up and tear down time which was about 2 to 3 shifts in each mining cycle, steel pipes were left in man-way between mining cycles. Cellular concrete was firstly introduced into backfilling stopes at Hollister mine in Nevada Mining. This process including concrete pump selection, pumping pipe selection, material mixing, material mechanics and quality control were fully covered in this paper. CUT AND FILL MINING CYCLE The most flexible mining method, cut and fill (Figure 1), was used to mine the high grade, narrow steep vein system on this Northern Nevada property which is located eighty miles north east of Winnemucca. Without top access, stopes were accessed through two man-ways on each end, in which people travel ladders and material transport slides were set up (Figure 2). Each mining cycle was called a cut, from 6 to 8 feet high. Overhand sequence was used. Mining cycle started with drill and blast the middle portion of the stope, then expanded towards both ends. Broken ore was slushed into mill hole located at middle of the stope and then mucked out through bottom access into main haulage. Stope length was about 300 feet, which was restricted by slushing distance. Timber man-ways and mill hole would be raised and established for backfill and ready for the next mining cycle.

Jan 1, 2011

By D. Kruse

Top down constructed large diameter (up to 90 m [300 ft]) shaft design and constructability issues present an interesting suite of challenges and opportunities highlighted in this paper. The study covers 2D and 3D finite element models used to: analyze various failure modes, evaluate the shaft liner and internal structures? response to seismic loading, assist in segment design, and assess final structural design tradeoffs. Efforts to achieve economic advantage over conventional heavy civil practices have prompted innovative solutions for ring and segment design, ring build assembly, and annulus backfill grouting. Intended for soft ground conditions, relationships between soil parameters and structure design are also explored.

Jan 1, 2011

By R. Gradnik

The continuous need for infrastructure expansion forces the mining industry to develop underground structures into more sensitive and violent environments. When underground excavation enters into deep and high stress rock conditions, geotechnical designers find themselves faced with the difficult task of selecting a rock support system that will meet today's stringent requirements. Whatever support system is chosen, it is mandatory that potential rock movement be controlled. All this has intensified the development of safety systems and new, unique solutions which can enable construction companies to go both, further and deeper, without reducing the level of safety. To address these needs, Atlas Copco developed the Roofex® bolt, specifically designed to withstand large static and dynamic deformations under prespecified load conditions. The Roofex Rock Bolt acts as stiff support up to a designable load level before the sliding effect of the mechanical frictional system is triggered and allows highly controlled rock mass movement without loosing the support function.

Jan 1, 2011

By M. Lohk, Y. -. R. Pastarus

Oil shale industry of Estonia provides a significant contribution to the country’s economy, but causes a large number of different problems. In spite of high economical parameters of the current underground mining (room-and-pillar) technology it is not effective. Backfill technology will be applicable in condition of Estonian oil shale mines. Nowadays attention has been focused on the use of combustion and mining by-products as filling materials. Use of ash and limestone in mining industry is treated as a part of mining technology, not as a waste disposal. Underground utilization of wastes reduces the volume and area required for surface disposal, environmental taxes. It improves the quality of mining works. The use of backfill technology has great impact on mining practice in Estonian oil shale industry.

Jan 1, 2011

By L. E. Beverage

In 2006, the Mine Improvement and New Emergency Response Act (?2006 MINER Act?), Pub. L. No. 109-236, 120 Stat. 493 (2006) was enacted in a bi-partisan move to strengthen the 1977 Mine Safety and Health Act. This action followed several underground coal mining accidents at the Sago and Aracoma Mines in West Virginia and the Darby Mine in Kentucky. The focus of that legislation was, in part, to force technological development and implementation. It involved the recomposition and training of rescue teams. Requirements for sealing worked out areas of mines were changed when MSHA invoked its Emergency Temporary Standard (?ETS?) authority for the first time in many years. Increased penalty amounts were established for certain types of violations for all types of mining, and minimums were set for unwarrantable failure violations issued under Section 104 (d)(1) and (d)(2); 30 U.S.C. Section 814 (d)(1),(2). The entire 30 C.F.R. Part 100 penalty criteria was revamped in a rulemaking, effective in April 2007. The visions were ambitious and noteworthy and those in industry and government have spent the last four years working through the aftermath of intended and unintended consequences of these changes. The penalty structure arrived at in 2007 has proven unwieldy and has contributed to the increase in contested caseload now before the Federal Mine Safety and Health Review Commission. In essence, litigation under the Mine Act ground to a virtual halt when the number of cases increased but the budget for Administrative Law Judges, who hear the cases, and the Solicitor?s office who represents MSHA, was not increased. Addressing the backlog effectively was one of the major challenges when Joe Main was confirmed as Assistant Secretary in early 2010.

Jan 1, 2011

By Bob Katsiouleris

Having passed through the worst of times for industrial minerals demand, there are signs that the best of times lie ahead. If the downturn was the result of unsustainable economic policy, the path forward has everything to do with sustain-ably meeting the demands of more people enjoying higher standards of living than ever before. Minerals producers must be poised to understand and meet their requirements well into the next decade. Successfully marketing industrial minerals - the building blocks of a growing and increasingly urban world population - will depend on producers? ability to respond nimbly to a rapidly changing and regionally evolving macroeconomic environment. A renewed focus on energy conservation, sustainable agriculture and building practices and consumer demand for products with a smaller environmental footprint will drive product and market segmentation strategies. These trends will not only shape the way industrial minerals producers do business, but also the type of skills and people they will require to run those businesses.

Jan 1, 2011

By A. L. Martikainen

In fluctuating airflow, continuous air velocity recording is the most reliable method of air velocity measurement. It allows for fast recognition of changes and the calculation of long-term averages. Also, it enables the mine operator to identify when the airflow has decreased to a point requiring action. Using ultrasonic anemometers provides an accurate option for continuous air velocity monitoring. This paper provides information about the effect of common obstructions in underground mining on air velocity readings. Stationary and moving obstructions are used to represent workers and equipment that would cause discrepancies in measured airflow. Also, it is important to know how large of a sample size is required to ensure reasonable accuracy of results. Statistical analysis is used to evaluate the required sample size. The sampling procedure is further studied by comparing two different sample rates. The results show that obstructions provide noticeable differences in air velocity measurements. Also, movement of obstructions can be recognized from changes in results. Surprisingly small sample sizes provide reliable air velocity information. Standard sample rates are found to be suitable for the underground environment.

Jan 1, 2011

By J. A. Botín

Identifying, quantifying and minimizing technical risks associated to investment decisions is a key challenge for the minerals industry decision takers and investors. However, risk analysis in most bankable mine feasibility studies are based on stochastic modelling of project NPV which, in most cases, fail to provide decision makers with a truly comprehensive analysis of risks associated to technical and management uncertainty and, as the result, are of little use for risk management and project optimization. This paper presents a value-chain risk management approach where project risk is evaluated for each step of the project lifecycle, from exploration to mine closure, and risk management is performed as part of a stepwise value added optimization process.

Jan 1, 2011

By S. Cotten

The regulations for current coal mine refuge alternative (RAs) require that there be sufficient life support to sustain survival of the maximum number of RA occupants for a minimum of 96 hours. This minimum duration assumes that rescuers can access the RA through the mine within four (4) days of the onset of the mine emergency. But what if mine rescue teams cannot reach the miners within the RA before the RA air supply is severely limited or exhausted? What could be done to extend the duration of the RA life support capability into the 97th hour and beyond? In addition, what might be done to enable more rapid rescue of the miners if they could not be reached through the mine in a timely manner? This paper describes a systems approach to address the potential need to extend the duration of RA life support beyond current design limits. New capabilities that need to be developed in advance of such a dire need include more reliable emergency communications, highly mobile and efficient drilling rigs, enhanced directional drilling techniques, and a standardized RA external life support interface along with RA internal design modifications to accommodate use of an external supply. The following sections describe the need, intent, and technology gaps associated with each of these capabilities. Government agencies and the mining industry should consider initiation of a program to investigate, design, and develop effective means of extending the current 96-hour time restriction on coal mine refuge alternative life support. The development process should begin with a focused study to refine the overall operational concept, investigate the current state-of-the art of critical technologies, identify specific technology development priorities, and make recommendations for a development program to provide in an organized, efficient, and timely manner a solution for extended refuge alternative life support and occupant rescue.

Jan 1, 2011