Search Documents

By C. Milne, T. M. Dyhr, T. E. Wilson

As time progresses, new concerns regarding long-term post-mining effects are identified, increasing mine closure costs. Regulators responding to public interest must take a “worst case” view and require post-closure monitoring or remediation processes. Although closure costs depend on the size and type of operation, general cost categories are defined, and median values (per acre, or per unit of production) are identified. Closure cost categories, as well as amounts, have increased with time. Except for increased efficiency in earth-moving and water management (surface or subsurface), there are no apparent offsets to a steady rise in closure costs. When the historical trend of closure costs is considered, it is probable that additional cost categories will come into being. For mine operators, the challenge will be to anticipate them and devise cost-effective remedies.

Jan 1, 2003

By P. Somasundaran, T. Chen, Diptabhas Sarkar

We have developed a layer-by-layer deposition technique for preparation of nanocomposite particles. Using this process, it was possible to make nanocomposites of various oxides with desired local composition and microstructure. The attachment of the shell particles to core particles was achieved using controlled polymer adsorption. Removal of excess polymer was accomplished without detaching the pre-adsorbed polymers by a specific stepwise washing scheme. The inherent chemistry of the process makes it easy to incorporate functional fillers over core particles. The nanosized filler materials will replace the shell particles in the present process and the polymer bridge would be chosen by taking into consideration the respective surface chemistries of various shell and core particles.

Jan 1, 2003

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health(NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

Jan 1, 2003

By P. F. Ziemkiewicz

This project evaluated the performance of nine passive treatment methods by studying 137 treatment units in eight eastern states. Performance was normalized according to construction cost, projected service life and tons of acid load treated. Results were dimensioned as $/tons of acid load treated/year. These costs were then compared to those of chemical treatment. Sites that achieved acid load reductions at costs below those of chemical treatment were considered successful. In addition to evaluating the performance of the treatment methods, this paper describes the various passive treatment systems, their applications and performance data for individual treatment units.

Jan 1, 2003

By J. S. Gardner, K. E. Houston, A. Campoli

INTRODUCTION Disposal of coal refuse is a costly and challenging problem facing the coal industry today. After the Martin County Coal Company slurry spill and the subsequent regulatory changes state and federal agencies are now beginning to require companies to justify new slurry impoundments. The authors have performed an analysis of different means of disposing of coal refuse for a major coal producing company located in the eastern Kentucky coalfields (the name of which will be withheld for the purpose of this paper). The company’s existing slurry impoundment is nearing its maximum permitted elevation and also an elevation where it may come in contact with abandoned underground workings. Due to the increased concern with underground mine works near slurry impoundments, additional consideration was given to raising the existing impoundment. Several other alternatives were evaluated, including but not limited to raising the existing impoundment, constructing a new slurry impoundment, constructing slurry cells, belt presses and others. This alternatives analysis was performed as part of a Section 404 permit for a valley fill and is currently being reviewed by the U. S. Army Corp of Engineers. All of the known possible alternatives were discussed in detail in the analysis. Due to the findings of the alternatives analysis, the company considers the engineered construction of the proposed impoundment to be the most favorable option of all the other alternatives evaluated, from both an economic and environmental standpoint. ALTERNATIVES EVALUATION FOR COALREFUSE/SLURRY DISPOSAL Background The company currently operates several deep mines and employ over 300 people and produces over 3.9 clean Mt/a (4 million stpy) of high quality, low sulfur coal. Currently, coarse refuse is belted to a valley fill, while, fine refuse is pumped to the existing impoundment. Coarse refuse is trucked to the existing impoundment as needed for construction purposes. The average recovery is approximately 50%; therefore, over 3.9 Mt/a (4 million stpy) of coal refuse must also be separated and placed.

Jan 1, 2003

By M. R. Nelson

Continuing experience in the Black Hills, South Dakota, indicates the persistence of several natural contaminants in mine waste effluents under circumneutral pH conditions. Selenium and arsenic are the most problematic environmental contaminants observed in these effluents. The contaminants are present in ore and waste rock as naturally occurring trace elements, and under the physico chemical conditions of the mine waste repositories are mobilized by oxidation and desorption reactions into infiltrating water. Characteristics of the mine wastes, waste repository construction, and Black Hills climatic conditions, indicate these natural contaminants may persist well into the future causing long-term mine closure liabilities, a difficult challenge to both mine operators and regulators.

Jan 1, 2003

By Adam Feiler, John Ralston

Optical reflectometry was used to study the attachment and subsequent detachment of silica particles (diameter 25 nm) from the surface of titanium dioxide wafers under well-defined hydro- dynamic conditions. Atomic force microscopy was used to measure the interaction between silica spheres (diameter 7 pm) and titanium dioxide wafers under the same solution conditions. In addition to repulsive electrical double layer forces, adsorbed polyphosphates provide a short-ranged steric layer that reduces the lateral interaction between the surfaces. The use of these two complementary techniques has given valuable insight into the process responsible for fine particle detachment and has particular application to surface cleaning.

Jan 1, 2003

By Jörg Holzhäuser, Matthew Crow

An 18.5 km (12 mile) long tunnel is being driven by four Earth Pressure Balance Tunnel Boring Machines (EPB-TBMs) of 4.7 m (15.5 ft.) diameter through alluvial sand, gravel, silt and clay above and below the groundwater table in Los Angeles beneath buildings, railroads, freeways and the L.A. River. Continuous automatic data recording of TBM operation and field inspectors' records, accompanied by monitoring of 5,000 surface reference points and 268 borehole extensometers were used to obtain information. The paper explains the reason for selecting the method of EPB-tunneling to ensure stability of the tunnel and meeting of environmental requirements, and presents data collected to monitor and demonstrate the performance of the TBM sin the different ground conditions encountered.

Jan 1, 2003

By J. E. Gebhardt, D. King

Field-testing of a new on-stream X-ray fluorescence analyzer was conducted in a copper concentrator. The evaluation of copper tailings and concentrate streams indicated a statistically acceptable correlation with laboratory chemical analyses. The new equipment employs a “components off-the-shelf” approach to minimize capital cost and maintenance issues and to utilize the latest advancements in X-ray fluorescence detector technology and computer capability. A general description of the system is provided, and performance of the analyzer measuring copper (Cu), iron (Fe), and molybdenum (Mo) is presented.

Jan 1, 2003

By S. G. Mougiakakou

A computerized system (SCAPEVIEWER) based on landscape indices and artificial intelligence techniques is proposed in order to classify landscape images into various categories according to the quality of the pictured scenery. Photographs (totally 108) from various landscapes have been clustered, from seven experts in accordance to the mean estimation of landscape quality, into distinctive (C1), typical or common (C2), and indistinctive (C3). For each of the landscape photographs, ten (10) environmental and operational indices have been selected and determined, corresponding to visibility (V), naturalness (N), relief (R), flora quantity (FC), flora quality (F), water (W), skyline (SL), visual entities (G), season (S), and viewer position (P). These landscape indices are fed to a classifier. The classifier is a feed forward Neural Network (NN) trained by a novel hybrid method combining genetic algorithms and the back-propagation algorithm with adaptive learning rate and momentum. A total classification rate of 93.5% has been achieved, using only 8 input neurons. The discarded input neurons correspond to the indices S, and P. The pilot system SCAPEVIEVER has shown the feasibility of landscape photograph classification into three categories (C1, C2, and C3) according to the landscape quality, selecting simultaneously the most robust indices, by means of a computerized system combining the knowledge of an expert with a NN based classifier.

Jan 1, 2003

By S. Crewdson

Vertical hoisting of materials using hoists and skips is common in the Mining Industry. These systems have a number of drawbacks, one being limited hoisting capacity at medium depths. FKC-Lake Shore and Metso Flexowell have been developing and installing vertical belts for medium depth shaft applications for many years, progressively going deeper whilst increasing belt capacity. The latest development from Metso the Pocketlift® belt advances this technology allowing higher tonnages to be lifted from greater depths. The design, manufacture, installation and operational experience of a 1818 tonnes capacity, 273 meters vertical lift Pocketlift® system at the White County Coal Pattiki 2 mine is the subject of this work.

Jan 1, 2003

By H. C. Verakis, T. E. Lobb

During the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry, with coalmining being the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past several decades. Although blasting accidents usually represent a small percentage of the total number of mining accidents, they continue to occur and the severity of these accidents is disproportionately high compared to the other mining accidents. This paper is an analysis and summary of mine blasting accidents over the past several decades as they relate to surface coal mine operations. A compilation and review of surface mine blasting accidents from1978 through 2001 was made. The accident data was examined to identify the trends and primary causes, which continue to be blast area security, fly rock, premature blast, and misfires. Approximately 46percent of the causes of surface coal mine blasting accidents are attributed to blast area security, while fly rock, premature blast, and misfires represented an additional 50 percent of the causes. Accident categories were established based on the cause of the accident or the activity that was taking place when the accident happened. A discussion of the accident data is presented to increase hazard awareness and to emphasize safe blasting practices and MSHA requirements concerning mine blasting operations.

Jan 1, 2003

By J. Simmons, P. Ziemkiewicz

Acid-Base Accounting (ABA) is an analytical procedure that provides values to help assess the acid-producing and acid-neutralizing potential of overburden rocks prior to coal mining and other large-scale excavations. This procedure was developed by West Virginia University scientists during the 1960s. After the passage of laws requiring an assessment of surface mining on water quality, ABA became a preferred method to predict post-mining water quality,and permitting decisions for surface mines are largely based on thevalues determined by ABA. In order to predict the post-mining water quality, the amount of acid-producing rock is compared to the amount of acid-neutralizing rock, and a prediction of the water quality at the site (whether acid or alkaline) is obtained. We gathered geologic and geographic data for 56 mined sites in West Virginia, which allowed us to estimate total overburden amounts, and values for maximum potential acidity (MPA), neutralization potential (NP), net neutralization potential (NNP), and NP/MPA ratios for each site based on ABA. These values were correlated to post-mining water quality from springs or seeps on the mined property. Overburden mass was determined by three methods, with the method used by Pennsylvania researchers showing the most accurate results to actual overburden mass. A poor relationship existed between MPA and post-mining water quality, NP was intermediate, and NNP and the NP/MPA ratio showed the best prediction accuracy. In this study, NNP and the NP/MPA ratio gave identical water quality prediction results. Therefore using NP/MPA ratios, values were separated into categories: <1 should produce acid drainage, between 1 and 2 can produce either acid or alkaline water conditions, and >2 should produce alkaline water. On our 56 surface mined sites, NP/MPA ratios varied from 0.1 to 31, and six sites (11%) did not fit the expected pattern using this category approach. Two of eight sites with ratios <1 did not produce acid drainage as predicted (the drainage was neutral), and four of 40 sites with a ratio >2 produced acid drainage when they should not have. These latter four sites were either mined very slowly, had non-representative ABA data, received water from an adjacent underground mine, or had a surface mining practice that degraded the water. In general, an NP/MPA ratio of <1 produced acid or neutral drainage sites, between 1 and 2 produced mostly alkaline drainage sites, while NP/MPA ratios of >2 produced alkaline drainage with a few exceptions. ABA is a good tool to assess overburden quality before surface mining and to predict post-mining drainage quality after mining. The interpretation from ABA values was correct in 50 out of 52 cases (96%), excluding the four anomalous sites, which had acid water for reasons other than overburden quality.

Jan 1, 2003

By G. Barelli, C. Giusti, W. H. Langer

Natural aggregate – sand, gravel, and crushed stone – is the number one non-energy mineral resource in the world in terms of both volume and value. A plan for the sustainable development of aggregate resources can include: 1) policies and economic incentives to encourage identification and protection of potential resources, 2)efficient quarrying and processing of aggregate, 3) efficient use of primary aggregates, 4) greater use of recycled, waste, or substitute material, 5) inclusion of costs of all environmental impacts in price of material, 6) reclamation to beneficial secondary uses, and 7)identification of objectives, targets, actions, and sustainability indicators. Quarrying can also contribute to sustainable ecosystems through natural habitat reclamation.

Jan 1, 2003

By William R. Yernberg

The combined 76th Annual Minnesota Section of SME meeting and 64th Annual University of Minnesota Mining Symposium were held April 8and 9, 2003, in Duluth, MN. This year’s theme was “Stakeholders, Partners in Change.” The meeting included four keynote speakers, technical presentations and a tradeshow. Engineers, executives, mining managers and suppliers from throughout the United States and eastern Canada attended the meeting. Reflecting the theme of the meeting, all agreed that the mine owners, the government, the community and the employees are all “stakeholders.” They must be “partners in change” for the iron ore mining industry to survive in the region. Compared with past meetings, where improved technology was the primary focus, this year the focus was on the dramatic restructuring of the entire industry. As noted by several of the speakers, “This time, the change is not in technology.”

Jan 1, 2003

By Andy J. Robinson, Mark D. Claassen

Railroad companies and transit authorities have been slow to acknowledge that for many—utility crossings, a direct pipe installation below live rail can be just as effective as a more intrusive traditional cased crossing. Properly designed and specified pipe jacking work, and specifically pressure-balanced microtunneling, coupled with careful specification and analysis of geotechnical monitoring and, where necessary, ground improvement measures, can produce a low-risk, low ground movement solution to the needs of utility companies and municipalities whose services need to pass below urban and rural rail corridors. This paper discusses the design, geotechnical and ground improvement aspects of microtunnel crossings below active heavy and light rail lines and crossings beneath active subway tunnels.

Jan 1, 2003

By M. Hardy, K. Nielsen, M. Ramey

American Soda, LLP has commissioned the first solution mine for recovery of naturally formed sodium bicarbonate (nahcolite) from low-grade deposits using high-pressure, high-temperature injection fluid. This project, known as the Yankee Gulch Project, was commissioned33 years after discovery of the deposit and followed an intensive four-year feasibility study that included a full-scale pilot test. The nahcoliteis co-mingled with oil shale and is impermeable. Solution mining is achieved by a combination of thermo-mechanical cracking and dissolution. Elevated temperatures are required to initiate the thermally induced cracking and to enhance solubility of the nahcolite, which is highly temperature dependent. This paper will provide an overview of the development of the project from discovery, characterization, pilot testing, permitting and commissioning, with emphasis on the solution mining aspects.

Jan 1, 2003

By J. C. Yingling, V. Badaker, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

The University of Kentucky has developed reclamation cells at a surface mine in southeastern Kentucky to evaluate the impact of spoil handling (reclamation methods) and compaction alleviation methods on the physical properties of replaced growing media and on tree survival rate. From 1997 through 2001, penetration depth, penetration resistance, bulk density, and tree survival data have been collected at the reclamation cells and correlated to determine the relationships that exist between the soil physical properties at the site and tree survival. Regression models have been developed for each reclamation method evaluated using the collected data to predict tree survival rates on reclaimed surface mined lands as a function of the soil physical properties of the replaced growing media. Procedures have been developed for handling soil/spoil during reclamation that can minimize compaction in the replaced growing media. Procedures have also been developed for alleviating compaction in growing media on reclaimed and orphaned surface mined sites. These procedures, if implemented, will increase the potential for reforestation success. Finally, procedures have been developed for collecting soil physical property data for use in evaluating the suitability of spoil conditions for reforestation.

Jan 1, 2003

By K. Severin, B. Flanigan, P. Marion

"Plutonic-related" gold deposits in Interior and SW Alaska (Tintina Gold Belt) vary significantly in size, grade, vein/deposit morphology, depth of emplacement, distance from causative pluton and metal association. Metal associations such as Au-Bi and Au-As- (Sb-Hg) are a good empirical indicator of the depth of emplacement and distance from causative pluton. These associations have been used successfully in exploration. Results from several analytical techniques also suggest a phenomenological cause for these metal associations. Gold and bismuth have paired mineralogy at high temperatures and, thus, are best correlated at deposits that are deep and/or close to causative intrusions.

Jan 1, 2003

By S. Vivek

An Atomic force microscope (AFM) was used to measure the surface forces between hydrophobic silica surfaces. The measurements were conducted in the presence and absence of Cu(II)species in solution to study the effects of the cation adsorption on the hydrophobic force. The results obtained in the absence of the Cu (II)species showed that the hydrophobic force does not change with pH, while the electrostatic repulsive force changes substantially with pH. In the presence of the Cu(II) species, the hydrophobic force begins to decrease at a pH where Cu2+ions are hydrolyzed, indicating that the first hydrolysis product (i.e., CuOH+ions) are the species adsorbing on the surface of the hydrophobic silica. The results of the surface force measurements were used to develop a model for the adsorption of the hydrolysis product of Cu(II) species on the hydrophobic silica.

Jan 1, 2003