Search Documents

By Jean-Luc Cornet

Advances in conveyor technology over the past decade have enabled the design and erection of very long overland belt conveyors. Such conveyors usually require head and tail drives to lower the belt tension and belt strength required. This paper provides an overview of the problems encountered in controlling the head and tail drives on such conveyors and some of the solutions developed by CDI for several such projects.

Jan 1, 2002

Several years ago, Hudco Industrial Products began experimenting with the idea of levitating a conveyor belt with a film of air, much like the puck on an air-hockey table. While conducting its research, the company found out that some Russian and Dutch companies attempted the concept during the 1970s. After studying those conveyors, Hudco determined that its design was better. The Hudco advanced air-supported conveyor consists of an air-tight plenum, or chamber, that runs the length of the belt. The topside of the plenum has a formed trough. It corresponds to the profile of conventional troughing rollers. Low-pressure air is provided to the sealed plenum from a low horsepower blower. This pressurized air is metered and released through the central portion of the trough and reacts against the underside of the belt. The differential pressure between the top and bottom surfaces creates the lift to support the loaded belt. Airtight covers are installed to seal the transported materials in the plenum trough.

Jan 1, 2002

By Van Zyl Brink

A longwall-based coal mine in Australia, referred to in this paper as AusMine Colliery, experienced windblasts resulting from goaf falls. Windblasts were the cause of serious injuries and threatened the continued operation of the mine. A microseismic early warning system was installed and a significant success rate in providing early warning of large roof instability resulting in high velocity windblasts, has been achieved. Early warning of goafing is accepted as an operational tool on the mine. Severe demands are placed on the operator in terms of 'real time' interpretation. The development of an expert system allowed for a probabilistic approach to achieve automatic alarms. This paper will quantify the success, failure and false alarm rates achieved by manual operation and automatic expert system-based decisions making, respectively.

Jan 1, 2002

By William G. Pariseau

Few departments of mining, metallurgical or petroleum engineering in the United States have critical mass. Cost per student credit hour (SCH) in departments across the country are usually the highest among engineering departments, which are the highest on campus. Almost all departments are operating at fixed costs and enrollments could easily double without incurring much additional cost. However, the cost per SCH would remain unacceptably high and the probability of doubling enrollment is nil. Declining enrollment is a more likely future. The pressure to reduce SCH from university administration is unrelenting. And it has the potential for doing serious damage to program quality when standards and requirements are lowered in attempts to maintain enrollments and increase retention.

Jan 1, 2002

By L. Buckingham

Barrick Goldstrike Mines Inc. has embarked on a continuous improvement effort to ensure that Barrick Gold Corporation will retain its lead in the gold industry in years to come. The continuous improvement initiative is based on careful mapping of the key levers associated with each activity of business. The individual levers are then evaluated to determine their potential to affect the profitability and safety of the operation. The most promising are diagnosed for root causes. These root causes are then addressed to enhance benefits. Through a structured approach of mapping, brainstorming, evaluating and instigating change with follow up measurement and reporting; Barrick Goldstrike is anticipating an increase in throughput at the autoclave facility of 10% with little or no capital expenditure. The resultant approach to Continuous Improvement will be utilized throughout the Goldstrike facility and then throughout Barrick's world-wide operations.

Jan 1, 2002

By C. K. Kocsis, S. Hardcastle

Mine ventilation, requires electricity to operate the fans and fossil fuel for heating. Typically, this accounts for approximately 40% of the overall underground energy consumption. This is considerable, and one of the major causes of this expense is that most mine ventilation systems are designed for the "worst-case-scenario" with respect to ventilation demand, which is commonly dictated by diesel equipment usage. Once designed, mines tend to operate their ventilation system at this peak level despite their exceeding day-to-day development and production needs due to lack of appropriate ventilation controls. In underground metal mines, TeleminingTM, which includes the tele-remote operation of mobile development and production equipment from surface, will change the mine design criteria including its support infrastructure such as the ventilation system. With the removal of machine operators to surface control rooms, conventional ventilation systems designed to dilute and remove pollutants can become redundant. Depending on the ultimate need for ventilation, its cost in automated mines with tele-remote equipment operated from surface will be lower than the cost of ventilation in conventional mines. These cost savings, which could be significant, would not only come from the ability to reduce the amount of ventilation in the mine, but also through the capacity to automate its distribution. This paper provides an indication of the new airflow requirements in stopes and dead-end developments for the tele-remote and automated mining processes based on climatic modelling. Furthermore, this paper makes a cost benefit analysis by comparing the ventilation system operating cost of a conventional underground metal mine based on the mobile diesel powered equipment design criteria with the newly redesigned ventilation system operating cost of an automated mine based on the "heat management" design criteria.

Jan 1, 2002

By M. Valdebenito, J. Rajala

An OCS Expert control system was implemented by Svedala Cisa at the Minera Maricunga Refugio Crush-Leach Operation near Copiapo, Chile. The purpose of the Expert system was to maximize production through the primary and secondary crushing circuits and help balance crusher usage between each stage to maximize total plant production. Interesting aspects of the control strategies are discussed. Benefits of the control were verified through a randomized On/Off test program. Tonnage increases ranged from 5% to approximately 20% at good confidence intervals. Benefits analysis results are discussed. The crushing plant at Refugio is very remote and is located at approximately 15,500 ft. This poses many challenges. The effect of altitude and remote location on plant operation are discussed.

Jan 1, 2002

By R. F. Balazik

By March 2001, shrinking global markets, reduced consumer spending and declines in domestic manufacturing and industrial output ended the longest economic expansion in US history and pushed the nation’s economy into its first recession in a decade. Aggravated by the terrorist attacks of Sept. 11, the recession led to large reductions in the domestic production of processed mineral materials. Some of the most significant production declines in the US metals industry were registered by aluminum, copper and steel producers. They faced strong foreign competition, higher energy costs and lower prices for their products. However, homebuilding and other domestic construction sectors — major users of nonmetallic mineral products such as cement, brick, glass and stone — remained strong enough to help raise the output of industrial mineral materials slightly above previous year levels. A strong US dollar continued to weaken the competitive stance of US metal and nonmetallic mineral materials companies alike against foreign producers in markets at home and abroad.

Jan 1, 2002

By P. R. Shivdasan, R. D. Hagni

Cathodoluminescence microscopy (CLM) is uniquely applicable to the study of carbonatite-related fluorspar ore deposits. The mineralogy of the carbonatites, sodic and potassic fenites, marbles, quartzites and fluorite ores are readily determined and characterized. Calcite, dolomite, apatite and fluorite were deposited dominantly under high-temperature conditions, and they exhibit strong cathodoluminescence (CL). At the Okorusu, Namibia, carbonatite complex and fluorspar mines, three types of carbonatites have been recognized by field mapping and laboratory CLM. The main carbonatite intrusion is fine grained and consists mainly of calcite. A later phase of pegmatitic carbonatite consists of calcite, magnetite, Fe-rich pyroxene, apatite and pyrochlore. Pyroxene carbonatites were recognized mainly through their study by CLM.

Jan 1, 2002

By G. Wahl, H. Danilkewich, T. Mann

Developers of advanced mining projects face the challenge of how to craft a “Request for Proposal for a Feasibility Study” that will result in bids that are comparable and will lead to a successful execution of the study. Mining engineering consulting firms are challenged by “Request for Proposals” that may consist of a limited description of the Scope of Services and other items, which could present difficulties in the subsequent financing and/or development of the project. Changes in international disclosure requirements have also changed the landscape on how resources and reserves are reported by introducing new disclosure requirements and concepts such as qualified persons. This paper lays out a strategy for preparing a Feasibility Study “Request for Proposal” based on the experiences of a mining engineering consulting firm working on a diversity of projects around the world, and in light of the recent changes in international reporting standards for reserves.

Jan 1, 2002

By P. Coleman, J. C. Kerkering, S. Iverson

A fatal accident may result when a dozer is driven over a hidden void in a coal surge pile and the dozer falls into the void, burying and suffocating the dozer operator. This type of accident was analyzed by researchers from the Spokane Research Laboratory of the National Institute for Occupational Safely and Health using inexpensive fault-tree programs that had been developed, for use on a personal computer. Fault-tree analysis is a systematic safety-analysis tool that proceeds deductively from the occurrence of an accident event to the identification of the root causes of that event. The analysis identified basic and intermediate events that led to the burial of the dozer and graphically depicted the interrelationship between the basic events as well as the intermediate events leading up to the accident. A sensitivity analysis on assigned probabilities showed which events had the greatest influence on dozer burial in a coal surge pile. Operational guidelines and engineering controls are suggested to decrease the probability of a burial event.

Jan 1, 2002

By N. Harrigle, Tsutsumi

Very fine wet sizing of minerals such as kaolin, precipitated calcium carbonate, lime milk, and clay slip is a difficult process to achieve using standard vibrating screens. With particle sizes ranging in the sub-microns combined with the agglomerating tendencies of certain materials, screen blinding becomes a serious issue. Sizetec, Inc. has developed an innovative screening equipment to help solve this problem. The High Performer Screen uses powerful linear vibrations to help break apart agglomerated particles and prevent screen blinding. Optionally fitted with the Air Explosion Screen Cleaning System, compressed air can be periodically injected into the screen underflow chamber to clean the screen surface without the use of water sprays. This paper highlights some of the key features of the Sizetec High Performer Screen and describes typical performance that can be expected based on results from various trials conducted in the kaolin industries.

Jan 1, 2002

Editor’s note: As usual, the June issue features an industrial minerals review. And some thanks are in order. Thank you to the industrial minerals annual-review editor, to the technical committees chair and vice chairs and to the authors of the individual commodity profiles. Jim Norman of GeoTrans Inc. is the industrial minerals annual-review editor. Lucy McCartan, US Geological Survey, was the chair of the SME industrial minerals technical committees. She also served as the vice chair for agricultural minerals. Other technical committee vice chairs were: •Gary Tomaino, Specialty Minerals Inc., ceramics and refractory materials. •Srinivas (Vas) Veeramasuneni, US Gypsum, chemical raw materials. •William Langer, US Geological Survey, construction materials. •Vanessa Santos, Independent, fillers and pigments. •Richard Berg, Montana College of Mineral Science and Technology, specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of the readers, the editors thank them.

Jan 1, 2002

By P. R. Hervey, J. W. Foise

Quartz is the second most widely used electronic material, with approximately 3,000 t (3,300 st) of single crystals used each year. Most of the quartz used in electronics is synthetic and is manufactured using a technique called hydrothermal growth. This paper reviews the basics of hydrothermal growth, the feedstocks used for these crystals and the challenges to improving the growth process. This paper also reviews the processing of these crystals, the markets and applications where they are used, and the global outlook for these markets.

Jan 1, 2002

By Indranil Roy

Gua supergene enriched iron ore deposit from Jharkhand, India has been geostatistically modeled. Population modeling shows a negatively skewed 3-parameter log-normal fit for Fe and positively skewed 3-parameter log-normal fit for Al2O3 and SO2. Semi-variographic studies for Fe indicate spherical function fit using point kriging cross-validation technique with Co=4.06(%)2, C5.11 (%)2, Co+C=9.1 7(%)2 and 'a'=348m. Kriging with 50mx50mx 10m block size at 740mRL led to a global mean kriged estimate of 61.98% and kriging variance of 4.04(%)2 for Fe with central 90% geostatistical confidence limits at 61.39% and 62.24% for that level. This led to an ore inventory at 740mRL as 7.29 million tonnes of ore.

Jan 1, 2002

By Gustavo G. Pilger, Jair C. Koppe, João Felipe C. L. Costa

Information for mine planning requires to be close spaced, if compared to the grid used for exploration and resource assessment. The additional samples collected during quasi-mining are frequently located in the same pattern of the original diamond drill holes net but closer spaced. This procedure is not the best in mathematical sense for selecting a location. The impact of an additional information to reduce the uncertainty about the parameter been modelled is not the same everywhere within the deposit. Some locations are more sensitive in reducing the local and global uncertainty than others. This study introduces a methodology to select additional sample locations based on stochastic simulation. The procedure takes into account data variability and their spatial location. Multiple equally probable models representing a geological attribute are generated via geostatistical simulation. These models share basically the same histogram and the same variogram obtained from the original dataset. At each block belonging to the model a value is obtained from the n simulations and their combination allows one to access local variability. Variability is measured using an uncertainty index proposed. This index was used to map zones of high variability. A value extracted from a given simulation is added to the original dataset from a zone identified as erratic in the previous maps. The process of adding samples and simulation is repeated and the benefit of the additional sample is evaluated. The contribution of an extra sample was evaluated locally, globally and in terms of variation in total measured resources. The procedure showed to be robust and theoretically sound, mapping zones where the additional information is most beneficial. A case study using coal seam thickness illustrates the method.

Jan 1, 2002

By R. M. Clowes

LITHOPROBE is a collaborative, multidisciplinary research project that is providing new insights into the tectonic evolution of the North American continent through its work within 10 study areas across Canada. For the mining industry, such results provide a well-constrained regional framework and better understanding of the tectonic processes that lead to the development of ore deposits. In mining camps, seismic-reflection methods have proven effective in imaging shallow to moderately dipping lithologic contacts as well as structural features and, in some cases, have been used for the direct detection of orebodies. Here, short case histories are provided for the Abitibi greenstone belt (VMS deposits) in Quebec and the Thompson nickel belt in Manitoba.

Jan 1, 2002

By E. Bane Kroeger

Plane failure in rock and soil slopes is usually caused by the intersection of a discontinuity plane with a slope face. Normally, these discontinuities are weaker than the surrounding intact rock and provide a surface along which movement can occur. The discontinuities are typically analyzed to determine the stability of a particular slope. One problem that arises when evaluating the stability of a planar feature is that the method for planar analysis is two-dimensional and has difficulty dealing with planes that are oblique to the slope face. Several researchers have stated in the past that planar failures are a special case of wedge failure. Wedge failures occur when two planar discontinuities intersect in an unfavorable manner. Sliding can occur along the intersection of the planes. Wedge failures are very common in rock slopes and can often be problematic. Wedge stability analysis methods are typically three-dimensional and can analyze planar features that are very oblique to the slope face. Wedge failure analysis can also be used to determine the stability of planar features with good success. One advantage to using wedge analysis over plane analysis is that a tension crack can be both non-vertical and oblique to the slope face in the wedge analysis. This allows the engineer to more closely match field conditions. It also negates the need for the engineer to have two separate software packages to analyze a single slope, saving both time and money.

Jan 1, 2002

By J. Georgi

A number of infrastructure projects are on progress all around Greece at the moment. The common propose of these a project is the promotion of quality in: Design, construction and maintenance stages. They also comply with environmental management, which is, a method of organizing and implementing environmental protection measures. The paper includes by special reference on two important modern transport infrastructure projects for the development of Greece and its communication with Europe and the Balkans. Their landscape types and natural vegetation, local climate, geological conditions, altitudes, aspects and soil types vary As a result, upland landscapes in particular, are endangered. Due to the complex of nature of this environment, the development and the landscape design of the projects is a high challenging task. Wherever the nature of the projects requires intervention to the environment, they intend to follow the direct restoration of landscape and method for ecological balance. The implementation of landscape design of infrastructure projects, aims at restoring the landscape affected by construction works, incorporating transport works into the landscape, emphasizing on areas of particular interest (e.g. archaeological sites), while at the same time observing the principles of an efficient operation and safe use of the alignment. Landscape design provides, among others for the protection of slopes against surface erosion and the reinforcement of their stability, the improvement of road functionality, the aesthetic improvement of the landscape, adaptation of the road landscape to the greater environment, visual guidance of the user, screening of lights of the vehicles moving in the opposite direction, the protection against wind etc. The landscape design strategy and landscape applications are specified by special landscape guidelines and specifications that can be considered as part of the sustainable development of a alignment creating a high a esthetic scenery, ensuring the security of transportation and the environmental protection.

Jan 1, 2002

By Scott Stebbins

Cost estimating and economic evaluation software provide evaluators with the ability to predict the profit potentials associated with mine design alternatives even during project exploration and prefeasibility. Examining a multitude of development alternatives early on serves to identify aspects critical to profitability and to increase the reliability of economic projections. A case history illustrates how Sherpa Cost Estimating Software, when used in conjunction with Apex Software for Economic Evaluation, significantly enhances an evaluator's ability to examine design alternatives in a timely and reliable manner. The costs and economic impacts associated with various access routes, production rates, equipment mixes, and stoping methods are projected.

Jan 1, 2002