Search Documents

By Yasutaka Izumi, Tuneyoshi Funasaki, Keizou Miki, Makoto Kanai

INTRODUCTION The Tokyo metropolitan region, inclusive of the three neighboring prefectures (Kanagawa, Chiba and Saitama), has the highest concentration of population and industry in Japan; with an area of 13,500 km2 or only 3.6 percent of the national land, but a population of 31.8 million or 26 percent of the national total, and a Gross Regional Product (GRP) of146 trillion yen (US$1.33 trillion) or 36 percent of the overall GDP of Japan as of 1990. Tokyo Bay, embraced by the metropolitan region as shown in Figure 1 (a), (b), is open to the Pacific Ocean as a marine gateway and is ringed by large cities and coastal industrial zones together with port facilities, all constituting a concentration of prime importance for socio-economic activities. The Trans-Tokyo Bay Highway (TTB highway), which crosses Tokyo Bay and provides a direct transportation link between the west and east sides of the bay, has long been a sort of “dream-come-true” project in Japan. As shown in Figure 2, linked to the Tokyo Bay Shore Highway, Metropolitan Inter-city Expressway, Tokyo Outer Ring Road, Tateyama Express-way, and others, it will play an important role as an integral part of the regional highway network to help promote spatial redistribution and multi polarization of urban functions, thus strengthening cooperation between cities and restructuring the metropolitan region. The TTB Highway is a project of 15.1 km in length designed as a toll highway to cross the bay by tunnel and bridge, and will require ten years to complete at a total cost of more than 1,438 billion yen (US$13.077 billion). Following more than 20 years of feasibility and environmental assessment studies, construction of this giant offshore highway project commenced in May 1989 as the first large-scale highway project with private-sector participation under the prevailing Road Law in Japan, and is now steadily proceeding toward the goal of completion in fiscal1997. This report outlines the entire TTB Highway project, including the waterproofing measures against high water pressure and the rapid construction method applied in the construction of shield tunnel sections.

Jan 1, 1997

By E. D. Thompson, Y. J. Zhang, K. F. Unrug

This paper presents the results of a recent study on the development of an in situ testing method for determining coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using a penetrometer, which is an hydraulically powered device that uses an indenter to press on the surface of the borehole until the load reaches the failure point of the coal. The pressure and the penetration of the loading pin are recorded by a data-acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of the pillar-strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1997

By Thomas Sisley, Jozef Zurawski, Richard Switalski

Hilltop Interceptor Contract G is one of the segments of the wastewater control system in the greater Cleveland area. The tunnel is a relief interceptor constructed by the Northeast Ohio Regional Sewer District to minimize combined sewer overflows in the Easterly Service Area. The design study identified the need for a 3.35 m (132 in) diameter, 3.35 km (11,000 ft)in-line storage conveyance tunnel to be constructed at depths of 30 to 70 m (100 to 230 ft).Six structures for access, future flow drop, work shafts and overflow control were required to complete the system. The interceptor reduced the design peak flow from 12.5 m3/s(285 mgd) to 6.1 m3/s (140 mgd) by detaining in line 22,800 m3 (six million gallons) of wastewater.

Jan 1, 1997

By B. Govindarajan, T. C. Rao

A simulation of batch-flotation experiments was carried out using a simple empirical model to identify the process parameters that would give maximum yield at any given ash level. The relationship between the maximum yield values and the percentage ash-reduction ratio (ARR) has shown two regions where the collector and the frother dosages have individual influences on the flotation performance. Based on this observation, a simple "selection-criterion diagram" is proposed. This diagram can he used to select the process parameters to achieve maximum yield, for a given ash content of the concentrate and at any given flotation period.

Jan 1, 1997

By J. Paraszczak

Water-powered jackleg rock drills, introduced recently in South African mines, are reported to be more efficient, faster and more comfortable to operate than conventional pneumatic drills. Comparative testing of these drill types was performed in Quebec. Based on the test results and on time studies performed in the mines, water-powered drilling was reviewed. The review considered the drilling rates achieved, the infrastructure needed, side effects and health and safety considerations. This study shows that the application of water-powered drills may, under specific conditions, help increase the footage drilled and may improve the working environment. Examples of such applications are presented in the conclusions.

Jan 1, 1997

By Fredrick J. McGarry, Fred Moavenzadeh

In order to reduce the resistance of hard rocks to excavation by the available cutters, and in order to reduce the wear of the cutters and thus to increase the efficiency of the conventional tunneling machines and to improve their rate of advance in hard rocks, surface active agents have been studied in the controlled laboratory environments and have been experimented with in the field of actual tunneling operations. The laboratory study utilized a notched beam test to measure the effectiveness of 30 different surface active agents on the amount of surface energy required to cause stable fracture in the rock specimens. In addition to the type of rocks, geometry of the specimens, type of surface active agents, the effects of environmental factors such as temperature and degree of saturations were studied. The principle mechanism responsible for weakening of rocks in the presence of surface active agents was believed to be that of stress activated corrosion. The application of surfactants in the laboratory resulted in a reduction of up to 50% in rock strength, while limited experiments in the field have shown a 10 to 20% increase in the rate of advance. Substantial efforts both in the laboratory and in the field are needed to fully understand the mechanism involved and to utilize the effectiveness of surfactants as weakening agents for hard rocks.

Jan 1, 1997

By E. Molleman

This paper reports on testwork exploring the dissolution/reprecipitation reaction: ZnS + 2HCl ? ZnCl2 + H2S, as part of a process for the production of pure ZnS. In spheroidal form, this would constitute a premium fonn of zinc refinery roaster feed enabling the production of pure ZnO. The research focused on the influence of proton activity on dissolution of zinc concentrates from Brunswick Mining & Smelting, Red Dog and Tara. The results and thermodynamic data suggest that the three concentrates contained significant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1997

By C. Patrick

Annually, the US coal industry generates and must dispose of over 200 million st (180 million t) of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks with refuse blocks for use in ventilation stoppings in underground mines. Refuse, collected from three active preparation plants in eastern Kentucky, was used as the primary as aggregate in the preparation of concrete cylinder. Stress-strain analyses on the refuse cylinders yielded compressive strengths of from 59% to 77 % of the control-group strengths. Low variability within the groups was found while significant differences between the groups existed. On-going determinations of the effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1997

By Joseph Irons, David Westfall

Three rock tunnel sewer systems are underway in the Chicago Area. (Figure 1) The three are designed to act independently and to be later connected to the future tunnels of the master plan. The tunnel excavation for each of the systems has been completed. One is in the Northwest area within the City being built by the City, known as the Lawrence Ave. System. Another is in the Southwest suburbs, known as the LaGrange-Brookfield Sewer or Southwest 13A, being built by the Sanitary District, the third is in the South suburbs called the Crawford Avenue sewer or Calumet 18-E, Ext. A- being built as a joint venture between the City and the District. The three are similar in that they have the same purpose, the same component parts and their tunnels were constructed in the nigaran limestone using a mechanical mining machine. The purpose of each of the systems is two-fold. First to provide flood relief for existing inadequate sewer systems, and second to reduce the pollution load to the waterways caused by combined sewer overflows. The existing systems in the areas to be relieved are combined sewers built many years ago. The main outlet for the Village of LaGrange, for example, was built in 1908, is badly in need of repair and lacks the capacity to handle the flood flow from the heavily urbanized area it now serves. The dry weather flow from the area is taken off by intercepting sewers. However during

Jan 1, 1997

By W. J. Wuest, M. J. DeMarco, J. R. Koehler

Yield-pillar-based gate-road designs often fail to provide mine operators with adequate ground control. This is because of the unknowing m is employment of "critically" sized pillars. A "critical” pillar is one that is too large to either yield nonviolently or to yield before the roof and floor sustain permanent damage and is too small to support full abutment loads. To demonstrate the critical pillar concept, afield study of a tapering gate road was conducted by the US Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m (55.1-ft) wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m (40-ft) wide design more closely approaches proper yield pillar dimensions. A probe hole in several 10.6-m (34.8-ft) wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1997

By R. Lee Wooten, Marco D. Boscardin, James M. Taylor

An earth pressure balance (EPB) tunnel boring machine (TBM) and pipe jacking were used to construct a 430-meter-long segment of sanitary sewer force main. The force main was constructed by first jacking a 2045-mm-outside-diameter, reinforced concrete cylinder pipe (RCCP) casing through alluvial sands and gravels. Later, a 1220-mm-diameter, ductile iron carrier pipe was installed within the casing pipe. The main concern affecting the construction method selection was the elimination of the need for dewatering, which could cause groundwater flow from deeper, contaminated sands up across a silt aquitard into cleaner, shallower sands. In addition, the method selected reduced the volume of soil to be handled and, consequentially, the potential amount of contaminated soil to be managed. Items discussed in the paper include provisions for handling boulders and controlling ground movements as excavation and jacking occurred approximately 300 mm beneath an active,4800 kPa, 254-mm-diameter natural gas transmission pipeline.

Jan 1, 1997

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of screens were developed for the Coal Cleaning Simulator running under Aspen Plus during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for the size separation and a calculation for moisture content of the oversize product based on particle size and specific gravity distribution. This paper discusses the algorithm for predicting the moisture content of coal dewatered by screens.

Jan 1, 1997

By G. X. Wang

The nonliving dried water hyacinth (E. crassipes (Mart.) Solms) roots were investigated for biosorption of cadmium and lead and other heavy metal ions in aqueous solutions. Dried water hyacinth roots, when suspended in solution, strongly and rapidly sorb several different metal ions. Factors such as reaction time, pH, initial concentration of metal ions, presence of other metal ions and biomass concentration were investigated. Metal ions, including Cd2+ and Pb2+, were bound to the root in a very pH-dependent manner, with the binding increasing after about pH 3. High levels of removal were obtained. The adsorption was shown to follow the generalized Langmuir adsorption equation. The relative affinity of the roots for lead is greater than for cadmium. The maximum sorptions of the roots were about 33 and 86 mg/g for cadmium and lead, respectively. Only 15-20 minutes were required for the process of uptake onto the biomass to occur. The batch sorption kinetics of the uptake of cadmium and lead can be described by an apparent first-order reversible reaction model. The roots could be regenerated after the metal ions were stripped. A solution of CaCl2 in acidic medium appeared to be the best eluant for desorbing the sequestered Cd and Pb completely at pH 3. The kinetics of the metal stripping process was quite rapid. Successful desorption of Cd and Pb from the biomass by acidic CaCl2 solutions revealed that the metal uptake phenomenon is reversible, implying physical sorption of Cd and Pb.

Jan 1, 1997

By Robert Rautenberg, Paul McDermott

This paper will discuss the construction of 15.9 km (9.88 mi) of tunnels on a project in Chicago, Illinois. The tunnels were driven utilizing two rock and four soft ground TBMs ranging in sizes from 7.39 m (24.25 ft) in rock down to 1.95 m (77 in) in soft ground. In addition to the mining, there are 63 upper level structures and 16 dropshafts averaging 61.5 m (202 ft) deep included on this project. Many diverse mining, excavation, support and lining techniques were employed on this project.

Jan 1, 1997

By J. C. Stankus, J. J. McCaffrey, S. Guo, S. S. Peng

An innovative concept in longwall tailgate support is discussed. This new concept utilizes a high-capacity roof-truss system to replace conventional wooden cribs. The first field test was conducted at the Bailey Mine and was very successful. Similar tests were installed in other mines and seams. An extensive instrumentation plan was designed and implemented in the truss test area. The test data demonstrated that the dynamic roof-truss system effectively controls the various abutment pressures caused by longwall mining. Thus, a stable tailgate entry is maintained

Jan 1, 1997

By Thomas W. Traylor

Today, in Detroit, Michigan, a 14 ft. 6 in. diameter soft ground tunnel is being mined at penetration rates limited only by the logistics of liner handling and spoil removal. Soil conditions are highly variable and include clays ranging from very plastic to very hard, gravels, sands, silts and boulders. The permeable soils contain high concentrations of methane gas, compressed by groundwater levels some 40 ft. above tunnel invert. Despite these adverse conditions, mining crews frequently complete their 70 ft. production quota in six hours and go home. In one 4000 ft. reach of tunnel, progress averaged 68.9 ft. per mining shift. This paper has been written to explain this extraordinary accomplishment, and to demonstrate that truly continuous rapid excavation in difficult grounds is now limited by factors other than the excavation process itself. BACKGROUND The Detroit metropolitan area has a long and interesting history of soft ground tunneling. From 1949 to 1968 the city of Detroit alone constructed some 75 miles of soft ground tunnel. During this period the development and common usage of rotary or "wheel-type" soft ground tunneling machines was pioneered in the Detroit area. These machines are designed for, and were successful in, the cohesive or clayed soils that predominate the downtown Detroit geology.

Jan 1, 1997

A Mineração da Trindade (Samitri) is a major Brazilian iron ore producer. Founded in 1939, privately owned Samitri operates six mines with a total production capacity of 14.5 Mt/a (16 million stpy). The mines are located in southeastern Brazil in the state of Minas Gerais. They are operating in the iron ore quadrangle, Brazil's primary iron ore-producing region. In addition to iron ore production, Samitri has the capability to produce 350 kt/a (386,000 stpy) of ferruginous manganese ore from two mines, also located in the iron ore quadrangle. Historically, about 70% of Samitri's production of lump ore, sinter feed and pellet feed is exported. Destinations include Belgium, Luxembourg, France, Germany, Trinidad and Tobago, China, Turkey and the United States. Alegria Mine In September 1989, Samitri started a new processing plant to treat itabirite, a low-grade iron ore. The goal of the plant was to produce sinter feed (coarse fraction) and pellet feed (fine fraction). Primary separation of sinter feed from pellet feed was accomplished with conventional vibrating screens making a 0.4-mm (40-mesh) cut. The screen oversize was stockpiled as sinter feed. The undersize was deslimed with hydrocyclones and upgraded by conventional froth flotation. Resulting pellet feed grades ranged from 3% to 3.5% Si02. A change in pellet feed requirements by Samarco Mineração SA, a Samitri subsidiary, called for Si02 levels below 1 % and increased production levels. Moreover, market demands called for a change in sinter feed size distributions. Unfortunately, lower pellet feed Si02 levels could not be achieved with the existing process. This was because of the presence of 35% +0.15 mm (+100 mesh) in flotation feed. Flowsheet development. Laboratory and pilot-plant studies conducted at Samitri's research facility found that to achieve lower Si02 levels, the +0.15 mm (+100 mesh) in flotation feed must be kept below 5% to 10%.

Jan 1, 1997

By William S. Butcher

Research and development of tunneling technology is rapidly taking its rightful place as an important ingredient in the Nation's research and development strategy. The state of technology in tunneling is very important to the Federal Government. Through its support, both direct and indirect, of a wide range of public works, our government, using the taxpayer's money, is the biggest buyer of tunnels. So that this money is spent wisely and efficiently, it is important that potential developments in tunneling technology that promise lower cost tunnels be pursued, if the cost of reaching the goals is commensurate with the prospective benefits. For too many years, the Federal Government's activities in the tunneling technology field were fragmented. Recently, specific coordination efforts have been initiated. It may surprise some to realize that the total Federal expenditure on excavation technology research and development, which is largely devoted to underground excavation, is growing by leaps and bounds. In fiscal year 1971 alone, approximately $19 million were expended by Federal agencies. This current fiscal year (FY 1972) that amount will increase to $24 million. It would appear that next year we will exceed the 1972 expenditure by 52 percent to bring the total FY 1973 expenditure up to $36 million. As most of this money is devoted to underground excavation, it is clear that the Federal Government

Jan 1, 1997

By W. A. Hustrulid

Introduction A problem that has faced mining engineers and mining geologists for many years is how to best explore a particular prospect so that the basic decision as to whether the material present is ore or only high-grade rock can be made with some confidence. It is obvious that one could not begin a large scale mining program on the basis of tests made on a few hand samples. On the other hand, one could not be 100 percent certain as to the average grade or tonnage before beginning development, as this would require the orebody to be mined out in the sampling process. The basic objectives of the exploration program can be stated as (1) to reduce mining risk; (2) to lessen the cost of development; and (3) to increase the profits of mining. The exploration program should be terminated when these objectives are no longer being met. The construction of tunnels is a specific mining operation. In the exploration program one should gather the data needed to determine (1) the type of excavation technique(s) to be used; and (2) the rate of advance that might be expected. As in the evaluation of an orebody, with the data collected it should be possible to estimate mining costs and project life. Unfortunately, at the present time, it is not possible to do this at least when dealing with medium to hard rock types. The reason for this, it is felt, is basically the inability to identify what specific rock mass properties are of use in tunnel design and to specify how these may be obtained in an exploration program. In short, the exploration program should be designed to give information regarding both the volume (length) and 'grade' (in

Jan 1, 1997

By Ching L. Wu, Joseph Penzien

An analytical procedure is presented for evaluating the stresses in linings of bored tunnels caused by kinematic soil-lining interaction. Three cases of interaction as produced by the following conditions are treated: (1) relaxation of in situ soil stresses near a lining following its installation; (2) overburden pressure at the soil surface; and (3) free-field soil response resulting from an earthquake. Non-dimensional formulas and graphs resulting from parametric studies are presented for practical tunnel design applications. The procedure is applied separately to a steel lining and a concrete lining for a site located at the lower end of Market Street in San Francisco through which a BART (Bay Area Rapid Transit)tunnel passes.

Jan 1, 1997