Search Documents

By R. E. Miller

Hoisting coal using water and air is a technology which has potential to improve the economics and safety of transporting coal. The Coal Air-Lift Hydrohoist is a prototype coal hoisting system developed by the U.S. Bureau of Mines (USBM). This paper discusses the method used to regulate the supply of water to the 50-m-high hydrohoist U-tube such that the pressure difference at the bottom of the U-tube is held constant. Maintaining a constant pressure difference results in a steady flow of slurry out of the hydrohoist.

Jan 1, 1995

By Louis A. Panek

Research on roof bolting has developed significant information with respect to the functions that can be performed by properly installed bolts and the methods that can be used to ensure that effective installation has been achieved. The present paper brings together results that are pertinent to the design of a bolting system for reinforcing horizontally stratified mine roof with vertical bolts. The design approach is based on the use of bolts to decrease the maximum bending stress within an arbitrary sequence of roof strata (such as shown by figure 1) in which the only loads are the weights of the individual beds. The use of rock bolts to achieve other objectives, such as to stabilize a fractured rock mass on the periphery of a mine opening (3), is excluded from consideration herein.

Jan 1, 1964

By Franklin B. Woodbury

As part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic needs, the U.S. Department of the Interior's Bureau of Mines is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed with a prototype monitoring system. A Californium-252 neutron source and a thermal neutron capture- gamma ray spectra analysis method was utilized to measure the amount of iron and the percent solids in the process slurries. The concentrate and tailing streams in a 410-kilogram-per-hour (900- pound-per-hour) pilot plant employing a selective flocculation and cationic flotation process were monitored. The results obtained showed that the thermal neutron capture-gamma ray reaction can be used to provide process control parameters.

Jan 1, 1979

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical when responding to a fire incident, as an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring fire contaminants, such as toxic gases and smoke, unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been developed by researchers and scholars around the world. However, those proposed methods rely heavily on a vast number of mine ventilation simulations, which is time-consuming and computer-resource intensive, especially for a large-scale mine ventilation network. In this study, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation is developed and implemented into the MFIRE mine fire simulation software. The results from the derivative method were verified against the results from a traditional method. The derivative method is proved to be reliable and accurate.

Dec 1, 2022

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method traditionally solves each mesh equation by an approximation during each iteration. Thus, it is interesting from both a theoretical and a computational viewpoint to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation that has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the solutions.

Jan 1, 1998

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013

By A. Benchekroun

The phosphate mining industry is confronted everywhere in the world with financial difficulties and low prices which prohibit further investments and development of new mines even in regions with a comparative cost advantage (North America/ North Africa/ and Middle East). But old mines are being progressively exhausted/ and if no replacement mines come on stream in the near future/ we may soon find ourselves (around the year 2000) with a global annual production capacity of 160 million tonnes of marketable phosphate rock instead of the capacity of 200 million tonnes existing today. Unless prices improve/ phosphate rock/ a non-renewable resource and a vital commodity to world agriculture/ may turn to be in short supply to world fertilizer industry. Whatever the extent of recovery of fertilizer demand/ the expected decline of the production capacity during the 1990 I s is bound to cause the disappearance by the year 2000 of the important surplus characterizing today the supply/demand balance.

Jan 1, 1995

By A. T. Visser

The expansion of surface mining has led to the development of very large off-highway trucks currently capable of hauling payloads in excess of 290t. Mine haul roads have historically been designed empirically, relying heavily on local experience; the trend in increasing truck size will thus render the current pavement systems inadequate. Since truck haulage costs can account for 10%-50% of the total costs incurred by a surface mine, not only would the maintenance costs of existing roads of inadequate design increase, vehicle operating and maintenance costs would also increase prohibitively. There is thus a need for improved design technologies encompassing the construction and management techniques of mine haul roads, appropriate for the wheel loads of vehicles now in use. The aim of the paper is to present the different components of a mine haul road design and management system and to demonstrate the value of its application through case studies. The system has been applied at several South-African surface mines and distinct benefits have been derived. The improved structural design of a new road resulted in a 29% saving in construction costs and also provided better service, whilst the optimal selection and management of wearing-course materials provided better functionality at lower total transportation operating costs.

Jan 1, 1999

By C. Flores

The most common experimental approach of studying one variable at a time while holding all others constant is extremely inefficient. Use of statistical methods enables engineers and scientists to obtain meaningful information with the fewest experiments, reducing cost and wasted effort. In particular, the Taguchi method can be more efficient than traditional full factorial experiment designs, as it can study more variables with fewer nuts, and it is more robust against process "noise." Taguchi designs are also simple to formulate and the results can be analyzed by simple PC spreadsheets. The role and benefits of using the Taguchi method in experiments to develop and optimize processes is discussed.

Jan 1, 1998

By David H. Dahlem

Uranium is a very mobile element geochemically and is widely dispersed in the lithosphere and hydrosphere. Under oxidizing conditions, it is particularly widespread and appears in all parts of the surface hydrologic system. As a result, this system is a leading candidate in uranium-resource assessments as a new base from which total resources might be estimated. No other sampling system provides the large volume geochemical capture as the continental hydrosphere and is as pervasive and non-selective regardless of rock type. However, the water system as a uranium metal sampler is not without drawbacks as the development of a National sampling program based on it has shown, In spring 1973, the National Uranium Resource Evaluation (NURE) was announced by the U. S. Atomic Energy Commission (AEC). The program was conceived to provide an evaluation of the domestic uranium resources and to identify areas favorable for uranium exploration. The specific NURE objectives are as follows (Bowyer, 1974): 1. To provide a preliminary evaluation of domestic resources and favorable exploration areas by early 1976, based on existing data. 2. To conduct a comprehensive evaluation of domestic resources and favorable areas by 1980, based on advanced state-of-the-art information. 3. To conduct an R&D program into new and improved procedures, equipment, and technology for uranium exploration and assessment. 4. To disseminate information on new exploration concepts and technology.

Jan 1, 1976

By Artur Skoczylas, Paweł Stefaniak, Sergii Anufriiev, Wioletta Koperska, Maria Stachowiak

In many underground mines the excavated ore is produced during the blasting process. Drilling machines that are used to drill the blastholes, where later the explosives will be mounted, are crucial for this task. In order to optimize the currently used techniques, great emphasis is placed on increasing the efficiency and safety of blasthole drilling operations. The natural consequence is the development of monitoring systems and algorithms for processing operational and historical data. In this article, we present the result of the analysis of drilling data carried out as part of the IlluMINEation project. The paper proposes an algorithm for work cycle detection for drilling machines, together with the estimation of general operating parameters and diagnosing the drilling process on the basis of long-term data. Based on the available data, selected components of the drilling cycles have been indicated. Several approaches based on the parameters of the defined cycles are proposed. These approaches can be used in the future to create a full-fledged system for examining the effectiveness and safety of mining drilling rigs.

Jun 25, 2023

By D. A. Peterson

A research program is currently in progress at the University of British Columbia to determine the potential of composite cable bolt reinforcement in Canadian mines. Several prototypes of glass fibre cable bolts have been tested. Their evaluation consisted of lab testing at the University of British Columbia, United States Bureau of Mines (Spokane) and trial installations at Detour Lake, Winston Lake, and Myra Falls Mines. A market analysis of cable bolts within the Canadian mining industry has been completed. Fibre reinforced polymer composites have a high potential as cable bolt reinforcement in mining applications. They prove to be a viable alternative to steel cable bolting.

Jan 1, 1993

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By Hans Breuer

The new regulations for the bituminous coal mining industry, issued by the mining authorities of the Federal Republic of Germany, are aimed at reducing to a feasible minimum any development of the coal workers pneumoconiosis (CWP) by lowering the admissible dust exposure of mine workers. Additional and improved measures of dust suppression and job assignment control *) are required for the purpose In this connection two basically different demands are placed on dust measurements: As far as dust suppression is concerned, the causes of dust development and the effectiveness of methods applied to reduce dust concentrations have to be identified, whereas with regard to the control of job assignment, the dust exposure of mine workers has to be depermined. Demands placed on dust measurements -- specifically for determining dust exposure -- are liable to become more severe since the threshold limit values were considerably reduced in these last years and since any additional dust suppression measures as well as a purposeful job assignment to certain mine workers are dependent on relevant measuring data. Therefore, research work has been carried out with the objective of measuring and evaluating, in terms of their effect (i. e. their incidence on the development of a CWP), size distribution, concentration, and specific noxiousness of any prevailing dust conditions.

Jan 1, 1980

By Hamed Khodadadi, Hamid Ghadiri

In this study, a fuzzy logic self-tuning PID controller based on an improved disturbance observer is designed for control of the ball mill grinding circuit. The ball mill grinding circuit has vast applications in the mining, metallurgy, chemistry, pharmacy, and research laboratories; however, this system has some challenges. The grinding circuit is a multivariable system in which the high interaction between loops, the variation of the system parameters with time, and time delay are some of the problems that pose a challenge. Since the controller parameters are determined offline in classic PID control, these gains are unchangeable and cannot overcome the mentioned challenges in this system. Hence, a fuzzy logic self-tuning PID controller, which is a combination of fuzzy logic and a conventional PID controller, is proposed to control the grinding system, especially in the presence of model mismatch and disturbances. In addition, in order to solve the system challenges, a multivariable control approach based on an improved disturbance observer is proposed to suppress the effects of the disturbances. The most important feature of the algorithm proposed in this paper as the combination of fuzzy logic self-tuning PID and improved disturbance observer is its ability to eliminate system interaction, attenuate internal and external disturbances, and compensate the effect of system uncertainty on the performance of the ball mill grinding circuit. Simulation results in the cases of the set-point change in particle size and circulating load in the presence of model mismatch and external disturbances confirmed the controller performance compared to other controllers.

By A. Konya

"INTRODUCTION Underground Mining and Construction projects face several challenges unique to the underground environment compared to the surface environment. The goals of an effective blasting program are the development of a blast pattern that minimizes cost, maximizes face advance, and provides the desired fragmentation and face profile. In addition to these , mines must consider the very real operational problems that occur such as drill deviation, ground vibration, and deadpressing or sympathetic detonation of explosives. These operation problems lead to increased costs and decreased production in the mine, hurting the bottom line. Combined with these problems, underground blasts can be difficult to monitor and evaluate due to tight spaces, dust during the blast obscuring video, and the need to evacuate the immediate area with no clear line of sight to observe performance. This creates an environment which most mines know that blasting can be improved in their underground operations, yet most are hesitant to change due to fears of the shot freezing, misfires occurring, and questions about how to achieve a proper design. The explosive companies and shot service providers also offer limited assistance or knowledge in the underground blasting realm, unlike with surface blasting, leaving many underground operations in the dark. It is for these reasons that most underground operations are operating decades behind the current technologies and incurring significant costs, both real and hidden, from there blasting operations. This paper discusses philosophical changes to designs that need to be made for effective design and modifications of underground blast patterns to prevent deadpressing and precompression of modern explosive products (Konya, Konya, & Worsey, Modern Blasting Method Selection, 2017). While numerous different methods of underground heading development exist, there are two types that are used in a majority of mines around the world, these are the burn cut and the V-cut. The burn cut is a parallel cut that has holes that go straight into the face and are primarily used in smaller opening (due to ability to pull deep rounds with smaller room widths) and metal mines (helps in ore dilution and greater fragmentation). The V-Cut is a cut that uses angled drilling towards the center of the face (in the traditional method) and is primarily used in underground aggregate operations due to its cheap cost but larger fragmentation sizes and greater throw of the muckpile. This paper will discuss these two forms of cuts specifically with the understanding that modifications to these can be applied to other parallel and angled underground heading techniques. BURN CUT The burn cut is one of the older forms of underground blasting, where a part of the blast (burn) of a shot is heavily loaded with additional empty (relief) holes with the goal of smashing (aka burn) and pushing/blowing all the material in the burn out to provide relief for subsequent blastholes. The relief holes in the burn cut provide a parallel relief for the holes that are firing to break too creating a second plane of relief, however these are extremely small and can cause many problems if a design is improper."

Jan 1, 2018

By Ewan Alexander

"As human beings, we have managed risk since the dawn of the ages and have been adept at doing so. In order to survive, we hunted or gathered. If we did not take enough risk, we died. If we took much risk, we died (Fig. 1). As individuals and tribes, risk had to be optimized to maximize our chances to thrive, as individuals and as tribes.In today’s world, the risks are vastly different, but in order to thrive, these must be managed. And no industry knows this as much as mining. In fact, the International Council of Mining & Metals (ICMM) has proposed the Critical Risk Model (Fig. 2) as a means of identifying critical risk, critical controls and associated performance standards. The ICMM focuses on sustainable development performance in the mining and metals industry. It has 23 members, representing some of the largest mining companies in the world.This approach is going to help the mining industry. But it must be applied effectively, with the acknowledgment that the system alone cannot be effective. We can say this confidently, as even companies known for the strength of their risk and safety management systems continue to experience significant incidents, and, in some cases, catastrophes. Why does that happen when all safety metrics, including injury rate, are pointing in the right direction? In the view of the author, it is only when leadership, culture and systems work in complete harmony that the resilience of an organization to manage its significant risk is at an optimal level. It remains an ongoing leadership challenge to maintain that balance and the optimal mindset in the organization. So how do you maintain that special balance?Let’s start with a basic premise. Leadership, supported by simple effective systems, creates culture which creates outcomes. Everyone going home safely is an outcome, as is cost effective operations, and to achieve those outcomes efficiently, the organization must focus on the inputs. And those inputs include effective leadership, effective systems (for the purposes of this article, risk and health, safety and environment (HSE) systems), good planning, stable operations and competent workers. This article will focus on gaining maximum performance from your risk management system."

Oct 1, 2016

By Xinchun Li, Youdi Zhang

AI is one of the computing methods, artificial intelligence performs its calculation by simulating the intelligent behavior of human beings. It is regarded as one of the most important scientific achievements in the 20th century, A1 has been developed rapidly in recent years with the development of the computer technique .The application of AI in the mineral industry has also obtained rapid progress sine AI has been used in early 1980's, such as evaluation of resource, underground mining, surface mining and mine safety etc. It has played an important role for increasing mining efficiency, improving mining management and ensuring the safety of the miner. An integrated A1 system has been developed for coalmines environment management in this paper.

Jan 1, 2002

By W. P. Diamond, A. C. Smith, J. A. Organiscak, T. P. Mucho

The U.S. Bureau of Mines examined bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U. S. coal mines. Results indicate that restricting airflow into mined-out areas (bleederless ventilation) is recognized worldwide as a spontaneous combustion control measure. However, ventilation practices commonly used to limit airflow to mined-out areas are not easily applicable to United States mining conditions, systems, experience and regulations. The types of bleederless ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems are discussed. Primary design considerations for bleederless ventilation consist of the interaction of ventilation practices, methane drainage, ground control, seal construction and mine monitoring. Technological improvements needed for U.S. application of bleededess ventilation are also discussed.

Jan 1, 1995

By J. O. Marsden

This paper presents an overview of the innovative methods for gold and silver extraction that have been put into actual practice in North America since 1987. It is an update of a paper of the same title which was presented by Sass and Mansanti at the AMC conference in San Francisco in 1987. New practices, new equipment and variations of older practices that have been introduced in the last five years are discussed in each of the following categories: process selection trends, comminution, gravity concentration, flotation, oxidation, agitated and vat leaching, heap leaching, solution concentration and purification, zinc precipitation, electrowinning, tailings disposal detoxification, and reclamation.

Jan 1, 1993