Search Documents

By S. K. Kawatra, A. K. Bakshi, T. C. Eisele

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By David D. Gallagher

Customer demand for greater efficiency and reduced operational costs on modern overland conveyors has focused attention on the conveyor belt's rolling resistance properties. Studies have indicated as much as 60% of the power losses on a long horizontal conveyor can be attributed to the indentation of the pulley cover rubber as it passes over idlers. This paper will compare tan delta values of different compounds with large scale rolling resistance test data from the University of Hannover. Results will then be compared to actual power consumption data gathered on several long overland conveyors using identical belt construction except with different pulley cover compounds. Concluding comments will be made indicating substantial operating cost differences based on the rolling resistance of the cover compound.

Jan 1, 2000

By J. C. Yingling

An approximate analytic- model is developed for minerals liberation when comminution processes are applied to multi-component ores, i.e., ores that include grains of multiple mineral species. The model employs a one-dimensional representation of ore texture similar to that employed by King (1979) and Klimpel and Austin (1983). The spatial texture representation is viewed as being generated by a stationary semi-Markov process. Associated semi-regenerative processes are defined that can be used to establish, approximately, the joint distribution of particle size and composition, where composition refers to the identities and relative proportions of mineral species included within the particle. Numerical predictions made by the model are compared to size and composition distributions observed in previous experimental studies.

Jan 1, 1992

By GRANT COLLIGAN, BROCK O’KELLEY, Corby Anderson

With the world’s ever-growing push to expand technological capabilities, the need for specialized materials including rare earth elements has exploded. One source of rare earths found in the United States is bastnaesite, a rare-earth-bearing fluorocarbonate, mined at the Mountain Pass Mine in California. To increase production, it has been essential to optimize existing processes and create new ones to capture current reserves. This paper presents the results of a research program conducted to expand the understanding of the bastnaesite leaching system. With the help of prior knowledge and thermodynamic calculations, a novel single-stage hydrochloric acid leach system was created to optimize the extraction of rare earths from bastnaesite. Historically, this extraction has entailed the use of a two-stage leach system involving a high-temperature hydrochloric acid leach followed by a caustic crack. We ran a series of single-stage leach experiments by reacting locked-cycle flotation concentrate with hydrochloric acid to test common leaching parameters. The results of these single-stage tests showed significantly higher rare-earth recoveries than the reported recoveries of the historic two-stage caustic crack processes, all while decreasing the number and amount of reagents needed.

Feb 1, 2023

By P. Tsang, S. S. Peng

Mine floor failures, such as floor heave and floor buckling, occur frequently in underground coal mines where soft mine floor exists. The types of failure can usually be classified into two categories; shear punching failure and tensile failure. A model based on the Winkler's elastic foundation is proposed in this paper for floor stability analysis. The model considers material properties of floor strata, in-situ horizontal stress, pillar size, entry width, and configuration of multiple-entry system and predicts stress conditions in the mine floor based on given in-situ mining and geological conditions, as well as deformation of the mine floor. This information is used to predict possible failures of mine floor by comparing the strength of mine floor with its stress condition. The validity of the model is verified by in-situ data described in this paper.

Jan 1, 1992

By Jay Hilary Kelley

A ventilation system is described using dual aircourses: one zone occupied by working personnel, the other at the active working face. The two zones are separated by a partition or Shroud. The occupied zone to the rear of the face zone is ventilated adequately but with considerably less air because little gas, dust, or fumes are present. The face excavating zone is sealed and maintained at slightly more negative pressure preventing dust and gas generating from within to escape. Explosive mixtures within the face zone is rendered non-explosive by the introduction of inert gas therein. Each zone is vented separately to the outside of the mine. Because less total quantity of air is required for human breathing, etc, the total ventilation system can be drastically reduced in tan capacity, development entries, and air shafts, -- a great savings in costs.

Jan 1, 1991

By D. L. Jones, S. Knoerr, J. Mansanti

The Buckhorn Mine in Nevada currently treats oxide ore using heap leach methods, but exploration has identified sulphide reserves which are refractory in nature. Preliminary testwork was conducted on the sulphide material to screen potential pre-cyanidation treatment methods. Processes evaluated included pressure oxidation, biological oxidation, nitric acid oxidation and roasting. An initial economic and process analysis of the results concluded that roasting was the only viable process, and only if the roaster off-gases were converted to soleable sulphuric acid. Further economic analysis indicated that roasting of the whole ore was more attractive than pre-concentrating by flotation, followed by roasting of the concentrate. These results were generalized to show that for high sulphur ore a roaster/acid plant combination is more attractive that either of the other options, ie. pressure leaching or bioleaching, provided the by-product acid is soleable.

Jan 1, 1990

By A. Martikainen

Field tests concerning a fog mesh method for fog removal are discussed. The first tests were performed at the Pyhäsalmi Mine, Finland. As this study gave promising results, further studies were completed at the Orivesi Mine. The results of these most recent field tests are presented and the two studies are compared. The Orivesi test set consisted of four materials. These included air filter fabric, fibrous filter fabric, a plastic greenhouse mesh, and an aluminium mosquito net. The variation of the Orivesi results was more noticeable than what was found previously. The best fog removal effect of all tests was achieved with the aluminium mosquito net, while the plastic green-house mesh performed worst. The humidity reduction by aluminium net was more profound than any of its precedents. More mesh materials will be tested in the near future.

Jan 1, 2007

By B. Denby, R. Hollands

Mine information is often multi-disciplinary, dynamic and spatially complex. Different departments use the same data in many different ways, information changes over time and mines change their shape continuously. Earthworks InTouch is a radical VR-based system developed by AIMS Solutions and marketed by Earthworks, which provides a rapid and intuitive interface to a wide range of mine information. VR is used to provide an interactive and visually accurate, dynamic 3D model of the mine workings and equipment operating in the mine. Individual objects in the mine can be linked to external applications that provide up-to-date and context sensitive information. Equipment movement can be simulated or tied in to real-time survey from GPS systems for example or excavator productivity data can be extracted from a production database. The paper will highlight the major advantages of using such a VR interface to access valuable and time sensitive information.

Jan 1, 2002

By Franco Oboni, Iain G. Bruce

The design of tailings containment structures relies on well-understood engineering methods being applied consistently. Unfortunately, not all facilities are designed or managed to the same level of competency. To standardize procedures, the Mining Association of Canada (MAC, 1998) prepared a “Guide to Tailings Management.” It recommended review of designs and an assessment of the risks associated with tailings impoundments be implemented during all phases of amine life. This paper describes how the quantitative risk assessment (QRA) process can be used to define risks associated with the design, construction and operation of a tailings management facility. And it discusses how, once the risk tolerability curves (RTC) are defined for a project, they can assist the risk management (RM) process.

Jan 1, 2002

By Verya Nasri

The use of a single tunnel boring machine (TBM) tunnel of approximately 12 to 13 m (40 ft to 43 ft) diameter for transit systems to house both light rail or subway tracks in a stacked configuration is an advanced concept that allows significant savings in construction cost and time while reducing, to a large extent, the negative effects on the environment. This solution, similar to the recently completed Barcelona Metro Line 9, integrates station platforms, train storages, crossovers, bypass tracks, ancillary areas and utility corridors inside a single tunnel. Each of the underground stations consist of a cut-and-cover entrance structure and ventilation shafts, that also serve as emergency exits. The excavations for the station structures and shafts can be done on one side of the street with nominal impact on traffic and utilities.

Jan 1, 2010

By M. Westerstrand

It is known that the water chemistry of the process water during ore refinement can affect product quality, such as iron pellet strength. The main objective of this study was to quantify the amounts of major elements, such as Ca, Mg, Na, S and Cl carried by process water and by magnetite grain surfaces to the end product, iron ore pellets made from magnetite ore from the Kiirunavaara Mine in northern Sweden. In addition, the amount of colloids (0.22µm ? 1kD) in the process water was examined by ultrafiltration. The amounts of various elements sorbed to the magnetite surfaces were estimated by leaching with Milli-Q water, MgCl2, NH4-acetate and Na-acetate. Total dissolved solids were between 1,446 and 1,775 mg/l, dominated by Ca, S, Na and Cl (89%). The colloidal fraction was less than 3% for major ions. For Ca and Mg, sorption to magnetite surfaces was a much more important transport mechanism for the pelletizing process than evaporated process water, but for Na, Cl and S process water was an important carrier.

Jan 1, 2010

By Art Hamid, Manfred Wong, R. John Caulfield

"The proposed Channel Tunnel is a critical component of the San Francisco Public Utilities Commission’s (SFPUC) Central Bayside System Improvements Project (CBSIP), which is a key element of a $6.9-billion sewer system improvement program to upgrade its aging and seismically vulnerable wastewater facilities. The tunnel will provide gravity conveyance and storage of combined sewage flows from the northeast sector of San Francisco, CA to the Southeast Water Pollution Control Plant for treatment. The tunnel will be approximately 2.7 km (1.7 miles) long and 7.3 m (24 ft) in internal diameter. It will utilize a single-pass precast concrete segmental lining system. Tunneling challenges include excavating with pressurized face tunnel boring machine (TBM) technology through highly variable ground conditions including the Franciscan Complex (rock and mélange), clayey/silty sands, stiff to hard clay (Old Bay Clay) and mixed-face conditions. The project will also require several deep shafts that will be technically challenging. Project backgroundThe SFPUC is a department of the City and County of San Francisco, CA that provides municipal power, drinking water and wastewater services to San Francisco.San Francisco’s combined sewer system collects both wastewater and stormwater in the same sewers, which is then pumped, treated to stringent state standards and discharged into the San Francisco Bay and Pacific Ocean. The sewer system includes tunnels, large storage/transport boxes, 1,600 km (1,000 miles) of collection sewers, 28 pump stations and three wastewater treatment plants. After decades of service, much of the system is nearing the end of its useful life.The existing system is also vulnerable to seismic damage. During the 1989 Loma Prieta earthquake, damage to SFPUC wastewater infrastructure was extensive. This included the 3,415 m (11,200-ft) long, 1.7m (66-in.) diameter Channel Force Main, built in 1976, and a critical component of the conveyance system. The Channel Force Main carries 70 percent of the bayside dry weather sewage flow from the northern and central part of the city to the Southeast Water Pollution Control Plant for treatment. It is antiquated, not pile-supported and not constructed to current seismic codes. There is also currently no conveyance redundancy for north/central bayside flows to the treatment plant. Figure 1 shows the SFPUC’s wastewater collection system, the existing Channel Force Main and the project location."

Jan 5, 2017

By John A. DesLauriers

INTRODUCTION This paper will update the status of small sized tunnel boring machines used in both the Mining and Civil Industries. I will mention a) new developments in small size hard ground tunnel boring machines, b) review North American performance records of the Atlas Copco Mini/Midi Fullfacers, and c) compare relative costs in driving a 1200m (4000 ft) typical utility tunnel using a leased TBM versus the conventional drill and blast method. NEW DEVELOPMENTS JARVA MACHINES Of all small rock tunnel boring machines currently in use, the Jarva MARK VI and MARK VIII are receiving the most enthusiastic acceptance. These circular fullface borers using usually 15 inch single disc cutters (manufactured also by Jarva) are designed on the 'T' bracing principle. Previously, Jarva's line of tunnel boring machines, even their smallest, was designed on the 'X' or double diagonal bracing configuration with a gripper in each quadrant. In small tunnels where net room is so very important, the 'T' scheme with gripping only at the spring line nets precious room around the cutter unit for passage of men and supplies. It allows freer un-

Jan 1, 1981

By Misra M., P. Grimes, Chen. S.

The combustion of petroleum products produces emissions which contain oxides of nitrogen (NOx), hydrocarbons (HC), and particulate matter (PM) which have adverse health and environmental effects. In recent years there has been increasing interest in the use of water-fie1 emulsions as a substitute for conventional fuels. Emulsified fuels are emulsions of water in fuel, which are typically made of 10 to 20 percent of water mired with certain additives and fuel. Studies have shown that the emulsified diesel can significantly reduce the emissions of NO, PM and car- bon monoxide and increase the fuel efficiency. In order to produce a stable diesel emulsion, the development of an effective surfactant additive is critical. The stability of diesel emulsions is influenced by many factors, including size distribution of the droplets, the viscosity of the continuous phase, the physical properties of the interfacial film, and temperature. This paper describes a method to produce emulsified diesel and combustion results obtained from various tests. It has been found that the diesel emulsion made with this additive package was stable during the test, and the emissions were lower in NO, CO, and PM compared to the baseline diesel.

Jan 1, 2005

The 1997 Rapid Excavation and Tunneling Conference (RETC) was held at the Mirage Hotel, Las Vegas, NV. The RETC is a biennial event jointly sponsored by SME and the American Society of Civil Engineers (ASCE). Conference attendance was 573 members, nonmembers and students, an increase of seven attendees from the 1995 conference in San Francisco, CA. Exhibitors occupied 51 booths at the Las Vegas RETC. The 1997 conference encompassed 58 presentations in 15 sessions. Participants were given details on achievements and advances that have resulted in new design solutions, alternative work practices and increased productivity within the industry. The page at the end of this article tells how to get your copy of the RETC proceedings, either hardbound or on CD-ROM. Or, if you wish, for the first time a CD-ROM is available with the complete RETC proceedings from 1972 to 1997. This two-disk, archival volume has key-word search capability, is in portable file format and is compatible with PC and Macintosh platforms. RETC program sessions included design and planning, ground support, tunnel boring machine (TBM) case histories, conventional excavation, new technology, difficult ground, geotechnical, shafts and raises, future/special projects, new Austrian tunneling method, international projects, soft ground case histories and water and gas. What follows are highlights of some of the RETC presentations.

Jan 1, 1997

By V. O. Tenorio, J. Puell

"Dump design is critical to effective mine planning in large scale open pit mines. Capital and haulage costs are considerable from early stages and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modeling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to optimize the ultimate dump design by minimizing its total dumping costs. The methodology consists of the formulation of a generalized model based on the relationship of the main dump parameters, followed by the use of linear programming to find the solution that minimizes the haulage total cost, and finally through a series of iterations, modifies the preliminary solution by projecting it to the topography and creating the ultimate dump design. A case study applied to a waste dump exemplifies this methodology. INTRODUCTION Open pit mine operations move large amounts of material on a daily basis from the shovel faces to the appropriate destination points. Hustrulid et al. identified three major destination places where the material receives downstream treatment after its delivery: mill processing, leaching dumps, and waste rock dumps [1]. The corresponding destination is given by a cut-off grade criteria, ore type, and the possibility of obtaining the maximum metal recovery. Dump leaching technologies have developed substantially since 1975 [2], and have enabled mining facilities to beneficiate low grade sulfide and oxide ores. As a consequence, the number of active dumps have increased since then and the entire mine configuration, which is limited in itself, has changed. The proper location, design, and construction of a mine dump must serve the safety, environmental and economic goals of the long-range mine plans. Therefore, an optimized use of the available surface area in the mine is highly desired."

Jan 1, 2018

By George A. Takach

The U.S. Bureau of Mines is conducting research with the goal of automating underground coal mine roof bolters for greater mine safety. In the project described here, the Bureau has focused on automating the drilling portion of the drilling and bolting cycle. A drill monitoring system designed and developed by Parvus Corp. of Salt Lake City. UT, was placed on a Bureau model roof- bolting drill. The drilling parameters of torque, thrust, rotation rate, penetration rate, and position are monitored through sensors connected to an asynchronous, control-oriented local area network (LAN) that communicates with data-accumulating and data-processing nodes. By placing microprocessors at the two data nodes and at the valve control nodes, and combining these nodes with a personal computer (PC), the monitoring and control system can achieve parallel processing capabilities. Such capabilities are referred to as locally intelligent distributed processing. Only data that have changed significantly are reported through the LAN to a supervisory control and data acquisition (SCADA) system mounted on an IBM- compatible 80286 PC. The SCADA system displays the values of the drilling parameters and calculates the specific energy of drilling, which is then used as an indicator of the type of rock being drilled. Besides monitoring the drilling process, an operator at the computer can control the rotation and thrust of the drill from a remote location through the SCADA program and can set drilling parameters on the basis of observed values of the specific energy of drilling.

Jan 1, 1992

By B. H. Kim

The use of a 25.4 mm diameter water-only hydrocyclone for separating fine-size (-150 µm), high-density (>4.5 g/cc) particles from similar-size, lower-density (2.65 glee) particles was investigated. It was found that a single-stage separation recovered nearly 90% of the heavy minerals (7.0 g/cc), while achieving a volume reduction of about 70%. The use of dense medium in a single stage improved volume reductions to 90% at similar heavy mineral recoveries. In addition, computer simulations of a three-stage circuit were performed, which showed that recoveries approaching 97% with volume reductions of 95% were possible.

Jan 1, 1998

By J. L. Vanderbeek

Investigations have been conducted at Chino Mines Company into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on the laboratory, pilot, and plant scales, to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 34% with a reduction in specific energy (kWh/ton) of 33%. Test results obtained to date are presented.

Jan 1, 1985