Search Documents

By R. C. Gilmore, S. A. Lolon, G. E. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Gob ventilation boreholes (GVBs) are widely used in underground coal mines for longwall gob degasification purposes. GVBs are often drilled within 10 to 30 m above the top of the coal bed into the fractured zone, completed with 20 cm (8 in.) diameter casing and 60 m of slotted pipe at the bottom. The purpose of this completion strategy is to create a pressure sink to capture the emissions before they can enter into the underground workplace. For GVBs to work effectively, they must be drilled close enough to the working areas to capture methane from the fractured zone while the setting depth must be kept above the caved zone to minimize the amount of ventilation air that is drawn into the GVBs. Well completion parameters are important for creating safe working conditions. In this paper, computational fluid dynamics (CFD) studies will be presented to analyze the effect of different practices for GVBs completion parameters for methane extraction, formation of explosive gas zones in the gob and methane concentrations at the longwall face and tailgate. Authors have identified the optimum completion parameters for GVBs, which can maximize the benefit and minimize fire and explosion risk. INTRODUCTION Coal mines may be considered gassy based on the presence of CH4. Gas from the mined coalbed or from rider seams above or below the mined coalbed can migrate into the gob and then potentially move towards the working areas. In longwall coal mines with high methane emissions, sufficient ventilation and additional methane control measures are usually required to reduce the methane concentration in working areas to below statutory levels. Several techniques or combinations of techniques are available to control the methane hazard. These may include mine face ventilation to dilute methane, coal bed degasification, nitrogen injection into the gob to render a methane atmosphere inert and the use of gob ventilation boreholes (GVBs). Longwall face ventilation and dilution alone can only handle methane emissions up to a certain amount. When methane emissions exceed the face ventilation capacity, additional control measures are required. Drilling horizontal or vertical methane drainage holes into the coal seams as well as gob ventilation boreholes from the surface into the gob area to extract methane are common practices. GVBs are usually drilled from the surface above the longwall panel ahead of mining. When the face moves outby the GVBs and the gob begins to form, methane production starts from the boreholes. It is important to control the performance of GVBs to maintain a safe working environment in the mine. The performance of GVBs depends on multiple factors, including borehole location, length and diameter of slotted casing, setting depth of casing above the coal seam being mined, wellhead vacuum pressure, and permeability of caved-fractured zones."

Jan 1, 2016

By G. Delagrammatikas, M. Karmis, J. Mastoris

The evaluation of raw materials in terms of quality profile, mineralogical character and mechanical properties is of great importance to the cement industry. The variability of their chemistry and structure is among the decisive design parameters in the choice of any mining, handling and preblending systems. Furthermore, clinker and cement production require sound estimates of the above parameters, to help produce some appropriate and realistic raw mix configurations and achieve minimum standard deviation of the major components. This paper addresses this subject from the perspective of a cement producer and presents the principles of a methodology aimed at optimizing mine planning and process design. Finally, results from case studies on actual sedimentary deposits currently in operation are discussed.

Jan 1, 2002

By K. W. Deter

The gold ores in the Jerritt Canyon district have been recognized as refractory since they were first encountered by FMC geologists in 1976. Upon obtaining managing rights as joint venture partner, Freeport McMoRan Inc. developed an operating plan featuring carbon-in-leach gold recovery techniques for the oxide portion of the ores and a patented sulphide oxidation step followed by chlorination for treating the organic carbon constituents of the refractory ores prior to CIL gold recovery. The plant was successfully started up in 1981 with the first gold poured on July 4, 1981. Initial plant throughput was designed to be 2495 MTPD (2750 STPD) total through the dual processing trains.

Jan 1, 1991

By Robert A. Jankowski, J. Drew Potts

By implementing various mining practices, mine operators can reduce the respirable dust exposure levels of the roof bolter and the continuous miner operators. The Bureau of Mines has developed a computer program, entitled AMP (Alternative Mining Practices), that gives a quantitative comparison of these reductions. The alternative mining practices and their corresponding reductions in dust exposure levels that are evaluated by the program include a remote control continuous miner, a half-curtain ventilation system, two auxiliary fan-tubing bypass ventilation systems, a modified cutting sequence, a comparison between single-split and double-split ventilation networks, and a comparison between exhausting brattice and exhausting tubing. Descriptions of each of these mining practices are included in the report. The report also includes a hypothetical case study to show how AMP enables mine operators to select the technique(s) that is best suited to their particular needs. AMP is a compiled basic program that has been designed to run on computers with a DOS version 2.0 or later operating system. It includes high resolution graphics (640 X 200 dot positions) designed to run with video boards that are functionally compatible with the IBM Monochrome/ Printer Adapter. Graphic screens are selected from menus, and can be bypassed if the computer is not equipped to handle high resolution mode. Their primary function is to show proper implementation of the mining practices evaluated by the program. This package requires a minimum of 256K bytes of RAM. (Reference to specific products does not imply endorsement by the Bureau of Mines.)

Jan 1, 1987

Australia is a hub for mining technology development. The paper describes many of the key players involved in mining research in this country along with some of the interesting research outputs to emerge over the past decade.

Jan 1, 2010

Introduction The US mineral industry in 1983 participated in the recovery from the recent recession. Compared with 1982, the value of raw nonfuel mineral output rose 8% to $21.2 billion. The $218 billion worth of goods processed from this crude mineral output represented a 9% increase over 1982. Even in real terms, these figures reflect growth. Demand for nonfuel mineral materials, of course, depends on the overall state of the economy, which steadily improved each quarter in 1983. Of particular importance to the mineral industry were surges in key mineral-consuming sectors such as construction and automobile manufacturing. New housing starts rose one-third, to 1.7 million units, while automakers turned out about 35% more cars (6.8 million) and 25% more trucks (2.4 million) than in 1982. These are significant increases, even considering recent trends toward smaller, lighter vehicles, and multiple-unit housing. A comeback for the mineral industry, however, is bound to proceed unevenly, particularly at the beginning. Traditionally, the industry lags behind the rest of the economy during a recovery, and some mineral products respond to overall economic improvement more quickly than others. This pattern has been repeated many times and the industry is used to it. Mineral executives know it is best to be patient and cautious during the first stages of an economic upturn. Many experts say that it may take extraordinary toughness, patience, and caution this time around. Steel Improves Raw steel production - a major indicator of both material use and mineral production - rose 14% to 77 Mt (85 million st), stimulating a 7% rise in domestic iron ore production to 39 Mt (38 million It). Still, the iron ore industry operated at less than half capacity, with most major mines remaining closed for part of the year. Iron ore imports dropped 24% to 10 Mt (11 million st), so demand was partly met by withdrawals from stocks. Despite the increase in steel production for 1983, output remained far below levels of just a few years ago. For example, 1983 production was still 29% less than in 1981. Raw steelmaking capacity actually declined about 10% during the year to 122 Mt (135 million st). The industry continued to cite steel imports, especially those from developing nations, as a major cause of domestic capacity loss. As long as steel production remains weak, steelmaking metals suffer. Domestic producers of bulk ferroalloys of chromium, manganese, and silicon operated at about one-third capacity in 1983, with six of the 19 companies involved being closed all year. The US mined no manganese or chromium, and very little nickel, although the country's only nickel mine did resume production in November. Molybdenum production, at 13.6 t (15 st), was only about one-third as much as in 1982. The major molybdenum mines, Climax and Henderson in Colorado, remained closed all year. To meet demand, molybdenum stocks were halved to 19 t (21 st). Mine shipments of tungsten, another mineral tied to steel production, dropped 30% to 1.1 kt (1,200 st) of contained metal. One of the most positive responses to the general economic recovery came from the aluminum smelting industry. By the end of the year, it was operating at about 79% capacity, compared to 59% in January. Nevertheless, the 3.3 Mt (3.64 million st) of primary aluminum produced represented only a slight increase over 1982. Total bauxite imports were about 27% below 1982 levels. Production of magnesium metal rose 11% to 100 kt (110,000 st). But titanium was more typical of other

Jan 5, 1984

By C. L. Karr

The efficient management of the distribution of goods and services is important throughout the minerals industry. From the scheduling of processing plant operations, to the routing of work crews in mines, to the planning of product development, vast amounts of time, energy, and money are wasted due to poor planning and scheduling. Thus, the U.S. Bureau of Mines is investigating computational algorithms that can be used to minimize the economic losses related to scheduling and allocating resources. Although there is commercial software available for tackling many scheduling problems, there has been little relief provided for solving the difficult traveling salesman with time windows problem (TSTW). The TSTW problem is a "derivative" of the classic traveling salesman problem, and can be used to minimize the distance traveled by vehicles or personnel to visit all points on a tour, with the additional constraint that each point on the tour must be visited within a specified time window. This paper is a survey of published work in which genetic algorithms have been used to efficiently solve the traveling salesman problem and its more difficult derivative, the TSTW problem. A genetic algorithm is a search algorithm based on the mechanics of natural genetics, and has been used to solve a broad spectrum of engineering optimization problems. Results indicate that the versatility, searching power, and simplicity of genetic algorithms can be used to provide substantial improvement in the area of scheduling and resource allocation.

Jan 1, 1994

By S. D. Michaelson

Open pits and quarries are the major sources of all "hard rock" tonnage mined today. Normally, ore is fractured from the pit face by blasting and then truck-hauled to a primary crusher where processing begins; over- burden (or waste) is generally truck-hauled from the pit to dump areas. Truck haulage of blasted ore and overburden accounts for some 25 to 50 percent of total mining costs in a typical open pit and commonly is the largest single cost factor. Obviously then, cost reduction efforts should properly focus on improving existing haulage systems and developing new breakthrough techniques for material transport. Continuous flow systems for large tonnages ordinarily will result in a lower cost than batch systems such as truck or rail haulage. Continuous flow with pipelines for liquids and slurries, or conveyors for medium to coarse dry materials (in the -8 in. range) are the accepted economic answers for bulk materials handling over reasonable distances.

Jan 1, 1968

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral-processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. When a sensor goes off calibration, it results in errors that can have a severe impact on plant economics. Classical statistical approaches fail to detect when errors are “subtle,” unless they grow and become large enough to be “gross,” whereas methods based on signal processing and artificial intelligence fail in dealing with the complexity of process fluctuations. Due to the sheer volume of sensors, undetected errors are not remedied until the next calibration, which on average are a year apart across all industries [1]. This research aims to detect such subtle errors (2 percent bias) in shorter time spans of about a month — rather than wait for errors to grow — using innovative data-mining techniques and algorithms.

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

By E. Farrokh

CSM and NTNU models are among the most commonly used models in TBM performance evaluation. Due to increasing application of TBM in different tunneling conditions, modification became necessary for these models. Sensitivity analyses on these two models indicate that both models are very sensitive to machine characteristics. Analyses performed on CSM database for cutter load and penetration rate prediction indicate while the r-square of the CSM model is reasonably high for the predicted cutterload, the r-square value for the penetration is low. In order to increase prediction capability of CSM model for penetration rate the model was reevaluated using non-dimensional analysis and the original database of Colorado school of mines. NTNU model is evaluated using Monte Carlo simulation and regression analysis. The results of analyses indicate that the majority of the variation of the penetration in NTNU model can be explained by only three parameters. This might indicate that the effects of other factors are overshadowed and it is worthy to reevaluate NTNU model using original database and more updated statistical methods to avoid overlapping of different parameters correlations.

Feb 23, 2014

By William R. Bond, Jim V. Rouse, Laura L. Damon

As noted by Damon (1990), "The time that a heap (of gold ore) is on the reusable leach pad is of critical economic importance." The Interim Neutralization Study, conducted by Brohm Mining Corporation (Brohm), at the request of the South Dakota Department of Water and Natural Resources and reported by Damon indicated that improvements could be made in leaching and pointed out the need for a better understanding of the gold ore leach procedures. To provide data on an actual heap, personnel from Brohm and GEOCHEM installed a series of pressure/vacuum lysimeters in an active Brohm heap, and conducted subsequent testwork to evaluate the efficiency of leaching. The objectives of the testwork included efforts to:

Jan 1, 1992

By Clifford R. Haryett

The potash industry in Saskatchewan, Canada, has advanced in numerous mining and ore processing areas over the last decade. This article describes these innovations and their effect on the industry in the area. During the 1970s, Canada's Saskatchewan province became a world leader, second only to the USSR, in potash production for crop fertilizer. Despite a serious oversupply in the early part of the decade, and a drop in demand due to the agricultural impact of the oil crisis, the Saskatchewan potash industry continued to make extensive capital expenditures to bring mining and processing innovations onstream. These innovations were directed at reducing production costs, improving work conditions, and overcoming environmental concerns.

Jan 8, 1982

By M. Galetakis, C. Roumpos

A sustainable coal industry needs to achieve a number objectives concerning mainly with superior utilisation of deposits and improved environmental performance. Modern quality control systems, which are greatly based on the on-line analysers, play an important role in achieving sustainability targets. This paper discusses the testing and application of on-line ash analysers installed in the Ptolemais and Megalopolis lignite mines in Greece and examines the possibility of using this type of analyser to control blending and homogenisation operations. The effect of the accuracy of on-line analyser to control process, when used for the characterization of low rank coals with complex and variable composition, such as greek lignites, is examined.

Jan 1, 2005

By Bart Lorang

Mining and mineral processing companies have historically leveraged technology and science to the fullest to reduce costs and improve product. Information technology is arguably one of the fastest moving technologies used by the mining industry. However, the business model for managing that technology and IT professionals often is fundamentally the same model that evolved from 1960's mainframe era. This paper will present a perspective of today's technology; review emergent computing technologies and attempt to id- advancements in computing anticipated in this decade. It will then discuss how the traditional IT model fits the technologies of today and the next decade. It will suggest roles IT professionals may play in the future to best leverage these technologies.

Jan 1, 2002

By R. H. Grau

The National Institute for Occupational Safety and Health's Pittsburgh Research Laboratory is now involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration's compliance dust-sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels and the controls being used. A summary of the mining operations, sampling procedures, resulting data and suggested methods to improve dust control are provided.

Jan 1, 2003

By D. Greene

The close integration of mine planning and mine operation continues to be the goal of mine operators. Depending upon the complexity, size and sophistication of the mine, limited success has been achieved in this area. Despite tremendous strides in the development of computer-aided mine planning, digital plans must usually be converted to error-prone paper maps and physical ground surveys for actual excavation and reclamation. However, advances in global positioning systems (GPSs), operator displays and mobile computers now enable equipment operators to work directly from on-board digital plans. A computer-aided earthmoving system (CAES) offers reduced survey costs, faster field transition time and improved excavation accuracy, coupled with faster, more informed decision making regarding key mining operations.

Jan 1, 2000

By J. Iannicelli

High intensity, high gradient magnetic separation can economically remove weakly paramagnetic contaminants down to 0 1 micron from industrial minerals This process is employed by all waterwashed kaolin producers in Georgia where seventeen huge magnetic separators are used to upgrade this product As a result, reserves of kaolin in Georgia have been doubled Design improvements have steadily increased the efficiency of separators and reduced power consumption below 300 KW for a nominal 65 TPH unit Beneficiation of ultrafine minerals is discussed based on pilot plant results on bauxite, ball clay, calcium carbonate, glass sand, talc, and numerous other minerals Operating parameters of the process are reviewed and some alternative equipment configurations discussed

Jan 1, 1983

By F. F. Aplan

Estimations have been made of the tonnage of raw ores and coal treated by various beneficiation processes. The amount treated by gravity concentration is substantially greater than that treated by flotation, with coal representing the bulk of the material treated by gravity means. A discussion is given of the trends and anticipated improvements in gravity methods. Except for the concentration of iron ores, magnetic and elec- trostatic separation processes find their greatest use in the beneficiation of non-sulfide ores. Exciting new developments in magnetic materials and separation process (and, to a lesser extent, in the electrostatic process) indicate a substantial increase in the application of such processes to ores and a broad variety of non-ore uses.

Jan 1, 1989

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time- dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct- shear tests on mudstone overcored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that the risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2002