Search Documents

By W. R. Reed, G. W. Luxbacher

As directed by the MINER act of 2006, the NIOSH Office of Mine Health & Safety Research (OMSHR) has annually awarded contracts to enhance mine safety and health. OMSHR has a history of research that focuses on both respirable coal mine dust and respirable crystalline silica (or quartz) dust, and contracts have been awarded since 2010 in support of our intramural research efforts. In 2018, a National Academies of Science consensus study report recommended expansion of respirable dust research. As a result, beginning in 2018 through 2021, eighteen contracts were awarded focusing on this area. These contracts can be grouped in three topic areas: characterization of coal/dust, development of real time monitors, and improvement of respirable dust controls. This paper summarizes the outcomes of completed contracts and the progress of current contracts.

Mar 2, 2022

"Above ground, elevated belt conveyors with span >200m between support points can cross valleys, rivers, forests and buildings with minimal footprint. The Cable Bridge Conveyor is a new type of suspension bridge based belt conveyor system that has long span between support points. It combines typical belt conveyor and the improved simple suspension bridge to form a conveyor bridge. The improved simple suspension bridge places a widened bridge deck directly on suspended cables, without the need for high truss towers. The benefits include reduced cost and increase aerodynamic stability compared to conventional suspension bridges. The Cable Bridge Conveyor’s compatibility with current belt conveyors allows the versatility in application. INTRODUCTION Belt conveyor is a ubiquitous material handling system. Conveyors can be placed directly on ground or elevated above ground by support structures. Considerations of cost, design, environment, civil work, safety and process requirements are all factors in choosing the ground based or elevated conveyors (1). The ground based conveyor has the lowest structural cost, where the conveyor is laying on an existing road. Maintenance access is easy and straight forward. Compared to the ground based conveyor, the elevated conveyor can cross existing buildings and structures, give passage to traffic beneath the conveyor, has smaller footprint, and requires less civil work to pass mountainous areas. The drawback of the elevated conveyor is higher structural cost, which can be compared with savings in civil work and other benefits. Conventional elevated conveyors are supported by rigid truss type structures, with typical span of 15m to 25m between concrete support bents or steel trestles. Triangular truss, using steel pipes instead of hot rolled steel sections, is more efficient. The typical span of triangular truss supported conveyor is around 30m to 40m, while the weight is about 10% less than conventional box truss with shorter span (2). Long span elevated structure based on suspension bridge is another step forward in increasing the distance between support bents, reaching 100m~400m and beyond. The very wide distance between support points of an elevated conveyor offers unique benefits. The conveyor can cross rivers, valleys, highways, forests and other obstacles with minimal footprint and reduced civil work. The versatility from long span conveyors makes bulk material transportation over previously impossible terrains now a feasible option."

Jan 1, 2015

By William N. Poundstone

Consolidation Coal Company, through the mining research division of Continental Oil Company, is now undertaking the installation of a full-scale hydraulic transportation system to carry coarse coal from the mine face to the preparation plant. The facility will include all elements of a fully integrated haulage system including face haulage for both longwall and continuous miner sections, multiple slurry feeds, hydraulic hoisting and 2.4 miles of overland slurry transport. This undertaking is a result of more than six years of extensive research and testing, some of which has been previously releasted to the literature. To provide a reference framework for system description, a brief history of recent coal mining technological developments will be discussed. Following World War II, mechanization resulted in mining machines that were bigger, faster, more powerful, and more reliable. These changes were essentially refinements in an established mining system. They made mining more efficient than before, but they did not change the system itself. By about the mid-1960's, it was apparent that further improvements in the extraction machinery would have a declining payoff, simply because .the worst bottlenecks were in other components of the mining system. A modern continuous miner cannot be run continuously because other operations underground cannot keep pace. In fact, most continuous miners today run at less than 20% of capacity. Consequently, in 1969 Consol and its parent company, Continental Oil, undertook a long-range R&D program to try to change the basic haulage system for the better. Most coal at present is removed from the mine by a hand-off system in which the coal is transferred from the continuous miner to a shuttle car, often with the aid of a separate loader; then from the shuttle car to a system of conveyor belts; and finally from the conveyors to rail cars. The system involves a large amount of moving equipment underground, many transfer points, and the everpresent chance of operational delays and safety hazards. By removing the haulage bottleneck, we believe we can speed up underground operations substantially; and perhaps more important, we could make it feasible to develop a whole new generation of mining equipment that is inherently safer. What we wanted was a truly flexible, continuous haulage system with inherent safety advantages. Ideally the system had to meet three major requirements: First, the coal had to enter the transport system at the face, and remain in that same system all the way to the preparation plant. Second, the system had to be flexible and extensible so that it could- follow the mining machine as it advances and retracts. And, third, the system must be inherently safer than current haulage technology.

Jan 1, 1977

By Alexander N. Winchell

"THE MICHIGAN COPPER DISTRICT.Location. The copper mines of Michigan are all in the north¬ern part of that state on the Keweenaw Peninsula, which extends from the (Michigan) mainland for about seventy miles northeast¬erly toward the middle of Lake Superior. The mines occur in a belt or zone occupying the central portion of the peninsula from end to end.. The most productive mines for many years past have been those located not far from the city of Houghton in' the central part of the zone, in a section extending about ten miles southwest of Houghton and fifteen miles northeast. The most important mines in order of.location, from the northeast to south¬west, are the following: Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet. and Hecla, Osceola, Franklin, Quincy, Hancock, Isle Royale, Superior, Baltic, Trimountain, and Champion. The first three named are in Keweenaw county and all of the others are in Houghton county. Still farther to the southwest are the Lake, Mass, Adventure, Michigan, Victoria, and White Pine mines. These are in Ontonagon county.History. The exploitation of these copper mines extends back into prehistoric times. There is little evidence that the American Indians carried on mining operations in this region in the period shortly before the advent of white men, but there is abundant evidence that the ancestors of the Indians, •or some earlier inhabitants of the region, carried on primitive mining operations. For example, Mr. S. O. Knapp, Agent of the Minne¬sota Mining Company, in the winter of 1847-48, made the first discovery of prehistoric mining. This event is described as fol ,lows by Foster and Whitney : Location: As shown on the accompanying map, the Mar-quette district extends from the region of Marquette on Lake Superior westward for about forty miles. The main basin of the district is only about three to six miles wide, but outlying areas which are commonly regarded as belonging to the same mining unit, make the north and south dimension of the district about twenty miles. The most productive portion of the area is in the vicinity of Negaunee and Ishpeming, .about ten miles from Mar¬quette, but important mines are found also all along the range as far west as Michigamme and also to the south in the fold known as the Republic Trough. Comparatively recent developments indicate that important ore bodies have been developed in the outlying Swanzy district about eighteen Miles nearly due south of Marquette.The Marquette Iron District.History: The first discovery of iron ore in the Lake Supe¬rior region was probably that made in 1844 near the site of Ne-gaunee by the government surveying party in charge of William A. Burt, sent out under the direction of Douglass Houghton. This surveying party was using a solar compass, invented by Mr. Burt, and noticed variations in the direction of the magnetic needle at various times and places, but. on the 19th of September, while running the east line of Township 47 North, Range 27 West, the needle varied from its normal position until it stood nearly at right angles thereto."

Jan 1, 1920

By D. Bleazard

Barrick Goldstrike Mines, Inc. is actively involved in improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. The identification of equipment failure modes and the development of associated capital asset management practices can minimize failure consequences. Successful programs have included; alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle, resulting in an associated reduction to repair costs and equipment down time.

Jan 1, 1997

By C. G. Snavely

Martin County Coal Corporation produces coal from seven continuous miner sections in two coal seams which are often interlaced with rock partings. Because of high clay content and coal oxidation, all minus 100 mesh material is discarded in the preparation process. We began experimenting with various drum lacings on continuous miners in 1983 to improve product size consist and increase machine cutting rates. To date, + 6.35 mm material has increased from 61 to 73% of mined product, minus 0.15 mm material has decreased from 6% to 4% of product, and machine cutting rates have increased by 50 percent.

Jan 1, 1985

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d'Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971

By Immo H. Redeker

Tile Asheville Minerals Research Laboratory is a member of the Engineering Research Department of North Carolina State University. The Laboratory is engaged mainly in applied nonmetallic mineral processing research to assist the North Carolina mining industry. A few out of state projects are handled at times. The Laboratory helped to bring the flotation process to North Carolina feldspar, spodumene, mica and phosphate producers and maintains versatile batch and pilot plant facilities at Asheville. It is of interest that North Carolina has now one of the newest and largest flotation plants at Lee Creek where Texas Gulf Sulphur Company produces 10,000 tons of phosphate concentrate per day, and one of the smallest flotation plants at Pittsburgh Plate Glass Company's fiberglass plant in Shelby, North Carolina where $50,000 per year of platinum-rhodium metal is reclaimed from wasted fiberglass furnace refractories in a tiny flotation operation of pilot plant size. The conservation of mineral resources through improved processing methods has been the object of most of the Laboratory's projects. This work has been extremely interesting and rewarding in many instances. Or, the example of projects for Kings Mountain Mica Company it will be demonstrated how waste could be reduced step by step from 20 tons of waste per ton of product to LO tons of product per ton of waste by improved processing methods. Brick, high grade potash feldspar, and silica sand are now produced from formerly wasted materials. AL this time Laboratory work sponsored by three feldspar companies, the State of North Carolina, and the U. S. Bureau of Mines, is aimed at reducing the amounts of feldspar tailings in the Spruce Pine area. Mineral dressing techniques are applied to reclaim saleable mineral products such as feldspar, mica quartz, and to make more uniform material for possible ceramic and other applications. Processes to produce new products such as sand-lime brick, and lightweight foamed autoclaved calcium silicate building products will be tested.

Jan 1, 1969

By K. A. Lewandowski

Binders have been suggested as an aid for agglomeration to improve copper recovery in heap leaching operations. However, it has not been established if the use of binders would negatively affect the solvent extraction process, which is used to purify the pregnant leach solution from the heaps and remove any contaminants. Such negative effects would lead to an increase in processing costs or a decreased in copper production. The controlled studies reported here have shown that some binders (a polyacrylamide and a waste treatment additive) did not interfere with the solvent extraction process. Other binders (a polyvinyl acetate emulsion and tall oil pitch) negatively impacted copper solvent extraction and, therefore, should not be used in copper heap leaching plants.

Jan 1, 2009

By Christopher B. Kapes

To reduce concentrate dewatering and drying costs, the Concentrator Division at Phelps Dodge Morenci, Inc. investigated available filtration technologies. Numerous methods were explored, including: drum, disk, belt, pressure, hyperbaric, and ceramic media filtration. An economic evaluation of the individual filtration technologies indicated the advantages of ceramic media filtration for Morenci concentrates. This paper discusses the technological development culminating in the first full scale application of ceramic media disk filters in North America. Low moisture contents are obtained at high production rates and greatly reduced operating costs.

Jan 1, 1994

By Francis F. Pitard

The presence of elements, minerals, or chemical compounds in materials at very low concentrations is becoming a constantly increasing concern for several segments of the Industry. Some trace elements or chemical compounds may be considered as hazardous, some are simply considered as undesirable In complex processes where they could be constantly recycled and end up as the major factor of decreasing quality for some valuable products. In some other cases, the presence of a trace element or mineral may be highly desirable because of its economical value: precious metals are falling into this category, they probably were the first trace elements to draw our attention. Tremendous quantity of money is spent for analysis at the trace level, also the analytical "tool" has been considerably improved during recent years, but still the sampling aspect of the problem remains obscur for many, and because of it, large quantity of analytical efforts become meaningless. Not only the absence of sampling strategies is badly affecting the representativeness of a large majority of samples, but furthermore for the same reasons, many laboratories are failing In their endeavor to prepare reliable standard reference materials. The reason of this failure has its roots in the unability to estimate effectively the sampling characteristics of the element, mineral, or compound of interest, not to mention the unability to perform precise and accurate complete analysis, so essential for the instrumental analyst (1). In this paper a strategy to perform a better sampling operation is recommended. SELECTION OF A PROBABILISTIC APPROACH AS SOON AS PRACTICALLY POSSIBLE It Is essential to differentiate probabilistic sampling from non-probabilistic sampling. As Illustrated in Figure 1, the sampling operation Is a selection process which could be performed In two different ways: I. A probabilistic selection process according to which all elements of a lot of material to be sampled are submitted to the selection with a same probability of being selected. 2. A non-probabilistic selection process according to which all elements of a lot of material to be sampled are submitted to the selection with different probabilities of being selected.

Jan 1, 1986

By F. J. Sotillo

Mineral processing requires good classification of particles to attain an adequate separation of minerals. This is of utmost importance in the case of sulfide minerals. An ideal classification is obtained when particles are separated at a given mesh, which is fixed according to the characteristics of each sulfide ore. Under these ideal conditions, particles coarser than the mesh of separation are recovered in the underflow, whereas particles finer than the mesh of separation are recovered in the overflow. This paper presents the results of pilot plant tests that were performed on Ag-Pb-Zn and on Ag-Au Peruvian sulfide ores using a Density Separator, and the comparison of these results with those obtained using hydrocyclones, under similar operating conditions. The results show that the ratio of circulating load is reduced by 50% by using a Density Separator with respect to that obtained by using hydrocyclones. Moreover, the effect of the improvement in the separation efficiency obtained by using the Density Separator on the kinetics of flotation is also shown. Silver recovery of the Ag-Pb-Zn ore increased by 18% whereas gold grade in the concentrate of the Ag-Au ore is doubled.

Jan 1, 1998

By James J. Anthony

High-angle in-pit conveying is an idea that is being seriously studied by a number of important mining companies in North America. Its application in coal, iron ore, and copper mining is expected to reduce mine operating costs considerably compared with the conventional discontinuous methods, such as truck haulage, which are fuel, labor, and maintenance intensive. Therefore, a mine introducing high-angle in-pit conveyors will gain a competitive advantage over mines which continue to use conventional haulage. While the capital outlay for in-pit conveyor systems obviously varies depending on pit depth, the angle of incline, and the capacity required, it generally will not exceed that of truck haulage when all Factors are taken into consideration. These factors include the cost of excavation, as measured in relation to the volume of minerals mined, the cost of building truck ramps and roads, and the capital outlay for the trucks and maintenance facilities. In many cases, in Fact, the capital outlay will be less than for truck haulage. This cost advantage will best be realized by new mines, whereas in existing producing mines the switch from truck haulage may involve the abandonment of a substantial capital asset.

Jan 1, 1983

By Shaoyang Yan, Xinming Chen, Huazhe Jiao, Huaibao Chu, Chang Wang

In terms of the technical problems of rib spalling in large mining height coal face, a long-distance advanced pre-grouting layer flexible reinforcement technology is proposed in this paper. Based on the mechanism and failure mode of rib spalling in the coal face, the mechanical properties of the aluminum plastic composite pipe were analyzed by using the tensile and compression experiment. The deformation and strength characteristics of “flexible pipe + grouting” specimens were studied by uniaxial compression test, splitting test, and shear test. The UDEC numerical simulation software was used to simulate the reinforcement effect of “flexible pipe + grouting” at different positions. Combined with the field application, the feasibility of long-distance advanced pre-grouting layer flexible reinforcement technology was verified. The test results show the following: The coal face has the characteristics of brittle and large deformation. The aluminum plastic composite pipe has the characteristics of good elongation and tensile strength, which can endure the large deformation of the coal face. The “flexible pipe + grouting” can improve the tensile and shear strength of coal. The UDEC numerical simulation analysis indicated that the grouting hole layout of “flexible pipe + grouting” has a significant difference in the reinforcement effect of the coal face. Compared with single row grouting reinforcement, the reinforcement effect of double row grouting holes 1.5 m and 3.0 m away from the roof is better. According to the field application, it is feasible to use aluminum plastic composite pipe as a flexible grouting pipe to reinforce coal seam with 80–100 m long-distance pre-grouting. Long-distance advanced pre-grouting layer flexible reinforcement technology can improve the daily production of coal and reduce the support cost of the coal face. As a new method of reinforcement, long-distance layered flexible reinforcement has a significant effect on the prevention and treatment of rib spalling in large mining height coal face.

Sep 27, 2022

By J. R. Walls

The United States potash industry had its beginning in the early Colonial days. Potash was initially manufactured by leaching of hardwood ashes in large iron pots. Production of potash was recorded as early as 1631 in New Hampshire, and in Maine a few years later. According to the census of 1850, the production of potash was America's most thriving chemical industry and, at that time, 569 plants were reported producing potash from wood ashes. Interest in potash was so great prior to the 1800's that the very first United States patent, signed by George Washing- ton, was granted for the production of potash on July 31, 1790. A new era for the production of potash began when potash was discovered by the analysis from a brine well in 1839 near Stassfurt, Germany while exploring for salt. The predominant use of potash at that time was in the chemical industry rather than agriculture. The discovery, by Justice von Liebig in about 1858, that potash salt contributed greatly to the essential plant food in soil opened up an enormous potential market for a suitable potash material.

Jan 1, 1985

By T. V. Subrahmanyam

Unlike coarse particles (40-50 µm), the fines (<10 µm) have low collision efficiencies with gas bubbles in flotation process. Among the alternative methods for recovering the fines are their aggregation with coarse particles (carrier flotation) and flocculation of the fines alone (shear-flocculation), prior to flotation. In any case, hydrophobic aggregation is the mechanism involved though the technique is known by different names in literature. This paper deals with theory and state-of-the-art of particle aggregation. To illustrate the dependence of aggregation on particle hydrophobicity, charge and, in turn, the sheer force, the results of quartz-DDACI and galena-xanthate systems are considered. In the flotation of complex ores selectivity is achieved by chemical control and aggregation of particles of the same species is analogous to that; however, more work is necessary on ores for a better understanding of the pulp chemical aspects from the view point of selectivity in aggregation. For a few ores, the results of earlier workers confirm improved recoveries of fines by aggregation prior to flotation.

Jan 1, 1997

By Charles H. Wells

This paper presents a review of the state of the art in coal preparation plant instrumentation and a discussion of automation practice that could be applied based on current mineral beneficiation experience and demonstrated foreign technology in coal washing plants. Specific e-mules of applications of remotely controlled slurry values, pneumatic and electronic field transmitters, computers for control and data logging, and on-line analytical instrumentation are given. A program, to demonstrate this technology is described.

Jan 1, 1980

By D. L. Shenck

The Navajo Mine is exclusively a multiple seam surface coal mine located in the northwest corner of New Mexico, and entirely on the Navajo Indian Reservation (Figure 1). It is owned and operated by the Broken Hill Propriety Co., Ltd. of Melbourne, Australia. The mine began production in January 1963 with a long term fuel supply agreement with the Four Corners Power Plant. The 2175 MW nominal generating capacity of the Four Corners Power Plant consumes 8-8.5 mm tons of coal annually. With estimated reserves totaling 1.1 billion tons of strippable coal, only one third is presently committed to the generating station. As development has continued over the years, mining operations have advanced into more complex geologic areas to satisfy the utilities demand for coal.

Jan 1, 1990

By R. E. Vivas, J. A. Villa

"INTRODUCTION Located in the state of Colima, Peña Colorada is one of the largest iron ore operations in Mexico. The project is owned in equal parts by ArcelorMittal and Ternium. Though boasting a production capacity of 4.5 million tons of concentrate per year, Peña Colorada is faced with declining ore grades. In order to respond to this situation, Peña Colorada had to expand production even further. This expansion created various challenges that were overcome by the adoption and application of new technology. Examples of these technological innovations are discussed in detail in this paper and include improvements in geo-modeling, mine planning and mine operations. The successful implementation of these technologies paid for itself many times over, and has led to significant improvements in production and performance, while lowering the operating costs and reducing the variance between planning and execution. PROJECT OVERVIEW Peña Colorada is a mining company which produces about 30% of the iron ore in Mexico. This project generates about 1,200 direct jobs and 3,000 indirect jobs, making a significant contribution to the local economy. Similarly, Peña Colorada invests in its local communities through numerous educational programs, scholarships, university agreements, social development, environmental agreements, etc. Peña Colorada’s operations consist of an open pit mine located in Minatitlán and a pellet plant located in the port city of Manzanillo, as shown in the location map below:TECHNOLOGICAL INNOVATIONS Most mining projects around the world typically follow the logic of “mining the next best ore”. Consequently, head grades tend to decline over the life of the mine. In the case of Peña Colorada, a decline in head grade combined with a decline in iron ore prices forced the operation to adapt to a new business environment and adopt new technologies to face these challenges. However, the first step along this process was to increase the confidence and reliability of the resource model. This task involved additional drillhole campaigns coupled with more detailed modeling techniques. Once the block model was completed, new optimization studies and production schedules were evaluated with new optimization tools that unlocked significant project value in many aspects of the mine plan. Similarly, new geotechnical studies were prepared, which provided new guidelines for pit slope design, and new technology was implemented to monitor ground movement and slope stability. The picture below shows two sectional block model views in MineSight 3D, along with the pit designs and geologic solids"

Jan 1, 2017

In 1991, Placer Dome Venezuela established a 70% stake in Minera Las Cristinas, to mine the Las Cristinas gold deposits in Bolivar. This case study examines the multi-sectoral partnership arrangement that was developed to improve health services near the proposed Las Cristinas gold mine. The investment climate in Venezuela is uncertain and the socio-economic circumstances are potentially hostile. Despite that, the partnership between the mining company, local communities, government agencies and an international health nongovernmental organization (NGO) collectively leveraged nearly $2.5 million to build and operate a community health center.

Jan 1, 2002