Search Documents

By D. Wallace Fields

Increasing public pressure and demands from various tiers of government have generated a legislative maze of statutory and administrative requirements facing industries involved in mineral extraction and processing. Each tier, of government has asserted concurrent jurisdiction and threats of harsh measures if industry does not satisfy all requirements. In the field of water pollution control, federal requirements have increased, carrying with them increasing techniques of enforcement - ranging from injunctions through criminal penalties. Federal laws have required that states formulate water quality standards as an adjunct to federal regulation. Florida has reacted with the Water Pollution Control Act of 1967. This act incorporates state water quality standards and permit requirements for any installation constituting a potential source of pollution, and provides for civil sanctions as well as injunctive relief. The federal government has utilized an 1899 law to require a permit for discharges into navigable waterbodies - a term which has been judicially defined to include any watercourse capable, after reasonable improvement, for use in the transportation of waterborne traffic. Failure to secure these permits can result in the issuance of an injunction or civil or criminal penalties. The Corps of Engineers will not issue these permits without the approval of the discharge by state, local and other federal agencies. Air pollution similarly is regulated by a multi-tiered network of laws and administrative standards. Federal regulation has increased from early research support in the 1950's through the development of Air Quality Standards and their enforcement by large fines, injunctions, administrative conferences and public hearings. Florida regulation, under the Florida Air Pollution Control Act of 1967, parallels federal law but grants concurrent regulations, requirements and enforcement tools to local and state agencies. Although previous state regulation was minimal, consisting only of three acts passed in 189 1, 1899, and 1911, in the future the mining industry will have to contend with this increasing network of ecological requirements. It is recommended that the industry take the initiative by involving Florida in the Interstate Mining Compact, as well as seeking the passage of a state reclamation law funded by a severance tax.

Jan 1, 1972

By Bruce B. Hanshaw

The Tertiary carbonate aquifer of central Florida is composed of about 2/3 calcite and 1/3 dolomite with minor amounts of quartz and apatite. The Mg content of the calcite is lower in the recharge areas than in the deeper confined parts of the aquifer system. Various geochemical lines of evidence indicate that much of the dolomite is of penecontemporaneous origin but that some may have been formed much later, possibly by ground water. Theoretical studies indicate that the Mg/Ca ratio in solutions is about unity for the three-phase equilibrium, calcite-dolomite-water. Solutions, such as ocean water and some subsurface brines, have Mg/Ca ratios higher than one and should represent dolomitizing solutions. In the areas of principal recharge to the Floridan aquifer, ground water is undersaturated with respect to both calcite and dolomite, and the Mg/Ca ratiois as low as 0.05. As the water moves downgradient, the Mg/Ca ratio systematically increases and approaches unity; saturation of the solution with respect to both calcite and dolomite also increases with length of travel in the system. Thus, in the zone of active potable-water circulation, the chemical process is one of dissolution of minerals until saturation is reached or exceeded. However, in the deeper brackish-water zones that underlie peninsular Florida, dolomite may be forming where the Mg/Ca ratio is greater than one. The necessary Mg may be derived from ocean water or brines recycled through the system as the hydrologic regimen is changed. The driving force may be simple mixing, relative fluctuations of sea level, or a combination of mechanisms.

Jan 1, 1972

By Kenneth N. Weaver

Introduction and Historical Background State Geological Surveys have been deeply involved in industrial minerals from their inception beginning in the first half of the 19th Century. To Massachusetts belongs the credit of having carried out the first Geological survey under state auspices on the Western Hemisphere. One of the causes leading up to this survey was. Governor Lincoln's message to the legislature of May 29, 1830, from which I quote in part: "Much knowledge of the natural history of the country would thus be gained (from a geological survey), and especially the presence of valuable ores, with the localities and extent of quarries and of coal and lime formations, objects of inquiry so essential to internal improvements and the advancement of domestic prosperity, would be discovered.". Similar phraseology is present in practically all of the initial organic acts creating the first State Surveys. High on the list of priorities for these embryo surveys was an inventory of the mineral resources of the State with particular emphasis on the industrial minerals. Prom these early beginnings, the state surveys have developed a great wealth of geological data either directly or indirectly relating to the development of mineral resources. One can gain some conception of the effort that state surveys today place on industrial minerals studies by noting the projects in which they are engaged as reported in the State Geologists Journal. In 1970, for example, approximately

Jan 1, 1972

By John W. Straton

Following the completion of the paper presented in February, 1972, data were received from many other mines and some original respondents submitted more complete questionnaires. The computer program was changed to permit the results to reflect more clearly all the data reported by the mines. The original paper was revised to reflect the new information. There were significant changes in some numerical values, particularly where the size of the sample changed appreciably. Some limited samples considered originally in arriving at conclusions were not relied on in this revision. The revised tables and text are of the same design and format as the original paper.

Jan 1, 1972

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By James C. Gilliand

Leo-potpourri, was selected as the title to this paper for several reasons. First, it is a fascinating word--not looking like it sounds or sounding like it looks. It also allows for a great degree of flexibility in designing a presentation around it. Further, it has become popular to use this eco hyphen something pattern. We hear of eco-mania, eco-hysteria and the like. Lastly, in this era of intense environmental concern, two of the principle elements on which the integrity of our efforts must be equated are ecology and economics. Accordingly, the term "Eco-potpourris" allows me to roam at will through the great number of considerations that make up this environmental issue. Whereas only a few years ago the subject of environment and environmental control had low visibility with the public, today it competes as the focus of attention with the many other popular social issues of our time. The program content here at this meeting, for example, is liberally represented by papers dealing with one or more aspects of environmental concern. If one would look at the 1964 program, in contrast, I would expect that no more than possibly one or two papers covered this subject and even then that those papers dealt principally with the environmental aspect of occupational health. It is gratifying that the program at this meeting demonstrates a serious awareness to a broad spectrum of environmental concerns. It would be a mistake, of course, to believe that this clamor for a quality environment is a "flash in the pan" that will soon subside. The general public has been thoroughly aroused and even frightened into

Jan 1, 1972

By Norman K. Olson

Hard-rock phosphate was formerly the chief source of all phosphate in Florida. Its mining began as early as 1883 or 1884, reached a peak level in 1907 and ceased in 1966. Production began and ended in the Dunnellon area (Marion County). Nearly all the hard-rock was exported because its P205 value per unit weight is generally more concentrated than that of other phosphate rock. Maximum production, achieved in 1907, was greater than 600,000 tons; the total value for that year was more than $4,000,000. The Florida hard-rock phosphate, considered to be of middle Miocene to early Pliocene age, has an intermittent narrow, linear northwest-southeast trend. The Ocala uplift controls the phosphate distribution for more than 200 miles. Other known, isolated hard-rock areas appear to be related to minor folds on the Ocala uplift. The hard-rock phosphate deposits are a heterogeneous mass of sedimentary fluorapatite, chert and quartz with textures ranging in size from clay to boulder, and in thickness from 0 to 40 feet. Phosphate compounds, principally fertilizers, have been in oversupply since before 1968, but by the middle 1970's some experts forecast a supply-demand balance. A brighter future for exploitation of Florida hard-rock phosphate depends upon one or more of these factors: 1) depletion of present premium grades (74 percent BPL and above) of land-pebble; 2) cheaper electric power from nuclear generators for profitable electric furnace operation; 3) supply and price of sulfur; 4) manageable rail-water transportation costs; 5) development of less costly mining and separation methods; and 6) minimum competition from high-grade foreign phosphate.

Jan 1, 1972

By Thomas S. Nye

Mineral exploration in the United States relies heavily on theoretical geologic concepts and indirect methods such as geophysics and geochemical prospecting, as there are few exposed areas of mineralization which have not already been explored at least once. In Mexico ore-grade samples can be cut at the surface on vein, replacement, and disseminated types of deposits in many areas. Here the problem is not in finding a mineralized area but in deciding which mineralized area can be explored and developed at the least risk and cost, and have the greatest profit potential, within the framework of Mexican mineral economics and government policies. Mexico's min¬eral industry is regulated through a system of permits for various phases of mineral exploitation, and by taxes. This regulation and its effects are not unlike those which may be expected in the United States if present legislative and administrative trends continue.

Jan 1, 1972

By S. E. Knalafalla

The availability of a fluid whose gross behavior sharply changes in a magnetic field without affecting its rheologic characteristics has been recently demonstrated. A colloidal solution of a ferrimagnetic material, such as magnetite, in a liquid that is immiscible with and lighter than water is projected for use in selective separation of particles according to their density spectrum in a continuous fashion. Magnetic levitation forces were created as an antigravity field when the fluid was properly placed in an inhomogeneous magnetic field. Five spherical non¬magnetic objects with densities ranging from 2.70 to 11.35 gram cm ' were made to float or submerge at will in a 0.96-gram cm-3 density fluid placed at vertical magnetic field gradients ranging from 0.2 to I kilooersted cm-1. The magnetic levitation farce in dyne cm-3 was found to vary linearly as a function of the object-fluid density mismatch with a slope equal to one g, the acceleration due to gravity.

Jan 1, 1972

By A. J. Lynch

Mineral commimition is an important and expensive industrial process and modern comminution circuits are complex There is considerable economic incentive to optimize circuit design and performance and to operate circuits at maximum efficiency, and these aims may be achieved by setting up mathematical models of the units in a circuit on a digits, computer and studying the behavior of simulated circuits. Models of grinding mills and cyclone classifiers which may be used for this purpose are discussed. The use of these models for design and optimization is discussed and particular mention is made of the factors which are important in circuit control. A digital computer-based automatic control system which has been successful in practice is described

Jan 1, 1972

By Richard D. Harvey

Relative quantitative analyses of certain mineralogical and textural properties of carbonate rocks were made with an image analysis computer. The instrument, referred to by its manufacturer as a Quantimet; consists of a petrographic microscope, a television camera and monitor, a detector, an electronic computer, and a read-out meter. Measurements were made on polished and etched specimens, standard thin sections, and on scanning electron micrographs of carbonate rocks. Critical to the success of the analysis is the preparation of the specimen in such a way that good optical contrast is obtained between the various petrographic components. The dolomite content, the pore volume, pore boundary projection, and pore size distribution of high-purity carbonate rocks were measured by image analysis methods. The frequency and size distribution of void inclusions in dolomites were determined by image analysis of scanning electron micrographs of cleaved surfaces. Image analysis methods permit rapid and quantitative assessment of various microscopic properties. The results are of reasonable accuracy and certainly are relative quantities that may be used to characterize carbonate rock materials.

Jan 1, 1972

By Richard W. Cannon

INTRODUCTION The authors, by means of this paper, will attempt to show the role of Induced Polarization and Resistivity surveys in the discovery of the orebodies of Gibraltar Mines Limited (N.P.L.). In this paper, we will also attempt to show the importance of conducting large enough surveys in order to properly evaluate the results obtained from these surveys. LOCATION The orebodies of Gibraltar Mines Limited (N.P.L.) are located on the western slope of Granite Mountain, central British Columbia (52°30' north, 122°16' west) (See Fig. 1). The property lies approximately 28 miles north of Williams Lake, B.C. and can be reached by way of 10 miles of newly improved road from McLeese Lake, on the Cariboo Highway. The area in and around Gibraltar Mines has a moderate topographic relief with elevations between 3,500 and 4,100 feet. {EARLY HISTORY AND GEOLOGY The present Gibraltar Mines property before amalgamation consisted of the Pollyanna property (Duval-Canex) and the Gibraltar property (original Gibraltar Mines) as well as some Coast Silver and McLeese Lake Copper claims (See Fig. 2). The Pollyanna property was first described in the 1917 B.C. Minister of Mines Report which referred to it as the "Rainbow Group". The development at that time consisted of several open-cuts on copper bearing quartz veins.

Jan 1, 1972

By Leonard Sugin

Recent changes in the field of ore and bulk commodity handling has forced a reevaluation of previously conceived notions. When vessels were small, and sources of raw material were reasonably close to areas of need, the role of the shipping terminal was of secondary importance. Now terminals must be built to take advantage of the economic benefits of the supercarriers. The shipping rates of the 80's will not be determined by the 60,000 DWT or even 150,000 ton capacity bulk carrier, but rather by the supercarriers in the 250,000 DWT class or larger. When the Suez Canal was closed, the shipping industry took a hard look at the economics of the large bulk carrier. Naval architects overcame the problems and successfully designed large supertankers, which today are plying the seas in excess of 350,000 DWT. Orders have been placed for tankers of 480,000 DWT. The shippers of dry bulk materials are now coming to similar conclusions about the economics of supercarriers. As of today, over 40 orders have been placed for vessels in the 250,000 DWT class, representing an investment of over 11/2 billion dollars, and many more are being considered. These vessels are being designed as combination ore/oil (0/0) or ore/bulk/oil (OBO's) carriers. The oil industry has seen the need for terminals which can accommodate these supertankers. The dry bulk shippers, and particularly ore shippers, must now act.

Jan 1, 1972

By Jean E. Tilden

An investigation of several trace elements distributed among sulfide minerals from deposits located in the southeastern United States was conducted. The deposits investigated are distributed within both the Blue Ridge Province and the Piedmont Province, which are contiguous geographic provinces. Twenty five deposits were examined;' eleven in the Blue Ridge Province and fourteen in the Piedmont Province. Figure 1 shows the locations of deposits investigated. In the deposits investigated, the mineral phases examined were pyrite, pyrrhotite, chalcopyrite, and sphalerite. These phases were chosen because of their relatively widespread occurrence, although no pyrrhotite was seen in the Piedmont Province. A total of 116 polished surfaces of ores were prepared, and mineral phases were collected from these surfaces for analysis. Samples were analyzed for cobalt, nickel, manganese, lead, tin, chromium, molybdenum, and gold. A total of 372 analyses were made. Trace elements were determined by atomic absorption spectrophotometry following standard procedures. In this study, trace elements are defined as those elements which are present in the mineral but which do not affect the chemical formula for that mineral. Lead is considered as a trace element only in ores where little or no lead sulfide could be identified as a distinct mineral phase.

Jan 1, 1972

By K. J. Reid

With the current trends of increasing costs and decreasing head grades the mineral industry is no longer operating in very high profit areas and has been forced to pay greater attention to the application of modern technology. Although here are many technological advances to the credit of the industry in recent years there are still many processes being operated in the traditional manner and still many areas awaiting the application of methods which have been proven in other industries. Compared with the chemical industry the mineral industry is seriously ageing in the general areas of process analysis and process control, more so than can be justified by the complications arising from having to deal with particulate systems with properties far different from ideal, or even non-ideal, liquid systems. One area in which there has been a remarkable lack of application in the Mineral industry is that of analog computation and the authors feel that there is considerable scope for the use of the analog computer in studying mineral industry processes. The paper outlines the basic principles and features of the analog computer and describes its role as a simulation tool in some engineering and mineral processing systems.

Jan 1, 1972

By John S. Cummings

Although there are many geologic situations which might be discussed at a session such as this, as I considered the problem, it became apparent to me that I should discuss a situation which has been of concern to me, and should be of concern to the geologic community. As a result, the questions which I will pose, and the criticisms, have not been arrived at quickly or easily, but have accumulated through time, to the point where I feel discussion is necessary. Very briefly let me say that my criticism of geologic mapping, of conclusions reached, and objectives or lack of such, results from my association with many areas where such studies have been completed, and resultingly my inability to comprehend the system of evidence or logic which supports extensive age-formational designations. The heart of the problem is that many conclusions resulting in geologic designations are based on weak or non-existent evidence, and such should be catagorized as hypotheses. Although the geologic community as a group does not approve or disapprove of such designations, it is evident that many or most of such designations attain a "status", and arc accepted as more or less valid statements. As will be shown, the amount of specific lithologic data provided in some quadrangle mapping projects is exceedingly slim. However, of concern herein is that the type of information presented at any stage is sufficient to warrant conclusions drawn. To see the magnitude of the problem, it is probably necessary to review some basic fundamentals upon which our geologic systems are established. The United States Geological Survey has defined a "formation" as the broad unit of geologic mapping consisting of a large and persistent stratum of one kind of rock. Obviously such a designation allows that a formation could be considered "time variant" in a horizontal as well as in a vertical context. However, other definitions enable a formation to mean units

Jan 1, 1972

By John E. Caffrey

Mr. William. J. Montgomery in his book "Theory and Practice on Mine Ventilation stated "Ventilation is vitally important to underground mining for three reasons: First, it sweeps all workings with a plentiful supply of air and drives to the outside the smoke, gases, and contaminated air which would be injurious to the miners; second, it dilutes and renders harmless the explosive gases emitted from the strata, thus eliminating the dangerous conditions caused by the accumulation of these gases; third, it keeps the mine air as nearly as possible of the same composition as the outside air, thus giving to the miner the healthiest possible condition in which to work...." Specific methods to achieve the above basic reasons for mine ventilation were established in the Federal Coal Mine Health and Safety Act of 1969. Sections 303(y)(1); (y)(2), and Section 317(f)(4) of the Act, which can be broadly described as entrapment features, are controversial and debatable in the minds of many mining engineers in their intent and method for affecting, 303(y)(1) in certain cases prohibits the use of belt haulage entries as an intake for face ventilation, This is to say that air traveling in a belt entry will be placed into the returns and not used for face ventilation, 303(y)(2) limits the velocity of the air on trolley haulage entries. The regulations, as published in the Federal Register, have set this limit at 250 feet per minute unless a higher velocity is approved by the District Manager.

Jan 1, 1972

By D. W. Leyshon

The fluidized solids technique for the calcination of phosphate rock has been well established for over 10 years. This paper is intended to review the recent performance of many of the Dorr-Oliver FluoSolids* calciners. In addition, design features of these three compartment refrac¬tory construction reactors will be described and a comparison made with fuel requirements for single compartment calcination. Also presented will be certain, aspects of the use of the rock including a discussion of non sulfate sulfur in the rock. A system is described for producing a blended mixture of calcined and uncalcined rock.

Jan 1, 1972

By David J. Barr

Public Law 91-190 - January I, 1970 states that, "The purposes of this Act are: To declare a national policy which will encourage productive and enjoyable harmony between man and his environment; to promote efforts which will prevent or eliminate damage to the environment and biosphere and stimulate the health and welfare of man; to enrich the understanding of the ecological systems and natural resources important to the Nation; and to establish a Council on Environmental Duality." The administrative aspects of this National Environmental Policy Act of 1969 have in essence established the requirement that all agencies of the Federal government assess the consequence of their actions with an Environmental Impact Statement. Furthermore, five states have already enacted environmental legislation, and others will surely follow. The Environmental Services Project Director for Dames and Moore has stated in the June issue of that company's publication, "Elements," that, "The nuclear power industry has perhaps been most affected to date by the Act [NEPAL but recent court decisions, legislative trends and general public concern will accelerate the spread of the Act's impact on other industries. Mining and petroleum are already involved in environmental affairs." There can be little doubt that within a very short time all environmental aspects of the minerals industry will be strictly regulated and monitored by some agency of Federal and/or state government. Indeed, it is probable that any future effort to extract natural resources will be contingent upon a favorable review of an Environmental Impact Statement. It is also quite possible that continuation of present operations will have to be justified on the basis of proof of an acceptable environmental impact. It is the objective of this paper to present some ways in which remote sensing technology can be applied toward an efficient collection of environmental data necessary for the preparation of an Environmental Impact Statement.

Jan 1, 1972

By Clarence A. Johnson

The discovery of the Prudhoe Bay field temporarily reduced interest in the development of coal conversion processes, but interest is being re¬newed by the current energy crisis. According to M.A. Wright, Chairman of the Board of Humble Oil and Refining Company(l), the reserve in the Prudhoe Bay bield has been confirmed to be about 10 billion barrels. At first glance this appears to be an extremely large reserve which will eliminate supply problems for the United States for some time. This feeling of security is lost when one realizes that by 1980 the world will consume the reserves of a Prudhoe Bay or a Libya, or Venezuela in less than a year, based on the recent predictions of U.S. and world reserves made by Eastman-Dillon, Union Securities Company(2). Recent forecasts of U.S. demand and source of supply made by Kenneth E. Hill of Eastman-Dillon are shown in Figure 1. This forecast shows a decline in domestic supplies (excluding Alaska) after 1973, with the total domestic supply leveling off in 1975 at about 13 million barrels per day. Since the predicted demand increases from about 14 million barrels per day in 1970 to about 20 million barrels per day in 1980, about 35% of domestic consumption must come from imports or non-conventional sources by 1980. More imminent is the shortage of low sulfur fuel oil which has been created by the new, tough air pollution regulations that are basically legis¬lating eastern coals out of the market. As an alternate to importing large quantities of low sulfur fuel oil or importing and desulfurizing regular fuel oil, one of two domestic solutions is possible: stack gas clean-up or solids fuel pretreatment. Stack gas clean-up may be the cheapest approach for old installations, but fuel pretreatment has real advantages for new installations. Coal pretreatment at the mine could eliminate all solids fuel handling

Jan 1, 1972