Search Documents

By Richard R. Radel, Jack Barry

Contract required excavating 2,000 If of 14' horseshoe tunnel in rock, a 95' deep work shaft on shore, and a 50' deep intake shaft located in the middle of the Niagara River just above Niagara Falls. Large quantities of H2S were encountered in the range of 20 PPM with ventilation. Peak levels of 40 PPM were recorded. The original designed ventilation system required only a volume of 10,000 CFM to meet OSHA requirements. The volume of air was increased to 50,000 CFM to dilute the H2S to al- low workmen to work and comply with OSHA H2S action levels. The second phase of the tunnel consisted of placing 72" ID X 20 foot long concrete reinforced pipe in the tunnel. When the tunnel was holed through and both shafts were open, a substantial amount of work was required to take place in the shafts which eliminated the possibility of placing a bulkhead to secure proper ventilation. The ventilation team designed a jet system airlock. The design of this system was to bring fresh air down the work shaft in two duct systems; one 30" diameter and one 24" diameter. Following the excellent work of Jan Wolski (7th Mine Ventilation Symposium chapter 58) our design incorporated nozzles located approximately 100' in by the work shaft. The velocity of the 24" diameter duct was 6,365 FPMD2.2 MPH. The velocity of the 30" diameter duct was 6,117 FPMl69.5 MPH. Both systems were on blow and being that air expands at 3112 degrees per side this high velocity of air expanded and created an air bulk head through which men and the large sections of concrete pipe could be passed without any delay or additional cost to the project.

Jan 1, 1997

Energy Developments Ltd. (EDL) has developed power plants at two Australian coal mines that featuring 94 gas-fueled Caterpillar G3516 engine/generator sets. They will convert to electricity 145 kt/a (160,000 stpy) of coal-seam methane gas for sale to a local utility. The $100-million project will cut the sites' methane emissions in half, provide a low-cost energy source and offset mine operating costs. The project began in May 1995. It is located at the Appin and Tower longwall underground mines, 80 km (50 miles) south of Sydney in New South Wales. The installation is one of the first to capture coal-seam gas from mine ventilation air and gas drainage systems. Coal- seam gas contains 40% to 60% methane, which fluctuates constantly. The system is expected to convert 578,000 m3/d (20.4 million cu ft/d) of coal-seam gas to 94 MW. It will also reduce greenhouse gas emissions by 3.5 Mt/a (3.8 million stpy) of CO, equivalent emissions. The Appin and Tower mines each produce 2 Mtla (2.2 million stpy) of clean coking coal. They operate around the clock with about 400 workers per site. The mines are owned by BHP Steel, Collieries Division, which will share the revenues from energy sales. The Appin Power Partnership consists of EDL and Lend Lease Development Corp.

Jan 1, 1997

By Chester M. F. Peters

The opportunity to make a close study of the available geologic data existing along the line of the California Aqueduct crossing of the Garlock fault in the Tehachapi Mountains was brought about first by my involvement in the prebid examinations, and later with contractors' claim cases. The California Aqueduct crosses through the western end of the Tehachapi Mountains and cuts across the Garlock fault zone at a location about 9 miles east from its junction with the San Andreas fault zone. This is about 65 miles northwest of Los Angeles and 38 miles southeast of Bakersfield (Fig. 1) (1). This map was published after the tunnels were started and shows the corrected geology. At the crossing the fault has north and south branches which extend northeastward for about 22 miles before converging. In the vicinity immediately east of the tunnel line the north branch of the fault starts to converge toward the west. After crossing the line it passes under the upper plate of the apparent easterly extension of the Pastoria thrust fault, so the actual junction with the south branch is obscured. The aqueduct design called for the expected active slip zone of the north Garlock fault branch to be crossed by the 2,800 foot long Pastoria siphon, which connects with the north portal of Tehachapi Tunnel No. 3. The tunnel would extend through the western end of Genghus Ridge which lies between the north branch and the main south Garlock fault zone in Beartrap Canyon. Here again the

Jan 1, 1997

Diesel engines are used in underground mining 1 throughout the world. Exhaust gases from those engines contain toxic components. To protect quality in underground mines, diesel emission control was introduced decades ago, many years before the first surface applications. Today, emission controls, such as catalytic converters, are standard on underground diesel engines in countries concerned with occupational safety and health. Nett Technologies manufactures a range of diesel emission-control devices for underground mining. Emission problems are not the same at each mining operation. And there is no universal control technology. The selection of exhaust aftertreatment technology depends on raw exhaust emissions, particular emission problems, fuel quality and economics. Some of the technologies that have been used in underground mining to control diesel emissions include catalytic converters, diesel filters, fume diluters and water scrubbers. Table 1 compares the effectiveness of these technologies to control the particular components or aspects of diesel emissions.

Jan 1, 1997

By S. Veeramasuneni

The interaction of soluble salt particles in their saturated brines is of interest from both a fundamental and practical perspective. The state of dispersion/aggregation of alkali halide particles as determined by optical microscopy can now be described based on non-equilibrium electrokinetic measurements for alkali halides. These results indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. These experimental results can be explained based on the interfacial polar interaction theory. In this regard the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems.

Jan 1, 1997

By D. G. Chedgy

This article presents a novel design, called the Climax High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 -660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Jan 1, 1997

By William T. Folwell

INTRODUCTION - CURRENT RAISE BORING PRACTICES Raise boring is a comparatively new tool to the underground mining and construction industries. Underground raise boring, in this country, had its beginning in the early 1960's, in the iron mines of Michigan. These first raises were bored 40 in. and 48 in. in diameter with maximum lengths of approximately 200 ft. Since the late "sixties", the raise boring machine has been accepted by the mining industry as an important machine to increase excavation rates, provide adequate ventilation airways, improve safety, and reduce costs, to name a few of the benefits. The construction industry is now accepting raise boring techniques for hydro-electric power projects, water supply projects, tunnel projects, waste water projects, etc. Raise drills are now capable of boring raises to diameters as much as 12 ft, in the softer rock types. Raise lengths range from 200 ft to as long as 1700 ft. Bored raises, in general, are bored at dip angles ranging from 45º to 90º, depending on the requirement of the raise. The general practice is to drill the pilot hole down to an opening below and up ream the pilot hole to the required diameter. The pilot hole (9-7/8", 9", 11", or 12-1/4" diameter) is generally drilled with compressed air to remove the cuttings. In the event that ground water is encountered and removal of cuttings is impeded, a foaming agent is added to assist in lifting the cuttings. When excessive water is encountered, water is used as the circulation medium and the cuttings are removed by pumping. During the reaming cycle, the cuttings fall by gravity and are removed from the bottom of the raise by conventional methods.

Jan 1, 1997

By John E. Urosek, Jack E. Tisdale

The Mine Safety and Health Administration (MSHA) has developed a Mine Ventilation Bleeder and Gob Training Course. This three day course is designed to increase the knowledge and understanding of bleeder ventilation systems. It discusses concepts, designs, plan approval, inspection and evaluation of bleeder systems. This paper will introduce some of the material contained in that course, focusing on the inspection, examination, and evaluation of bleeder systems. The regulations addressing the use of bleeder systems are found in Title 30 Code of Federal Regulations (30 CFR) Section 75.334. The examination requirements are found in 30 CFR Section 75.364. Section 75.364 de- scribes specific locations where examinations are to be made and specific information to be gathered at those locations. The required locations and information will be discussed in some detail with examples and illustrations. These weekly examinations for bleeder systems are designed to monitor the parameters of the bleeder system and to evaluate its effectiveness. Over time, conditions can develop in the bleeder system that affect the ventilation and lead to hazards such as methane accumulations. The hazards of methane accumulations need to be understood as such accumulations can contribute to mine explosions. The importance of additional information gathered by the mine examiner that can assist in evaluating the performance of the system will also be discussed.

Jan 1, 1997

By R. L. Bleifuss, S. Zhong, H. E. Geotzman

Microwave heating of iron ore was investigated as an alternative to conventional reduction processes to solve the problem of slow heat transfer. Microwave heating and reduction tests were run on composite green balls made from coal and magnetite concentrate. Benchscale tests were run on both powdered and pelletized feeds using a 15 kW microwave generator. A significant increase in the reduction rate was obtained. With 20% excess stoichiometric carbon in the mix, more than 90% reduction of the iron ore can be achieved in about 10 min at temperatures of around 1,000°C. The reduction of iron ore with coal by microwave heating produces a pure, dust free, high-Btu flue gas that can be used in related thermal operations. Depending on the purity, the reduced iron product could be fed directly to an electric arc furnace for melting. In some cases, the removal of a slag phase may be required to eliminate excess silica and alumina.

Jan 1, 1997

By D. Nilsson

This paper demonstrates the importance of including a discount rate in the determination of the optimum final' depth of an open pit. Without a proper discount rate, a pit will probably end up too deep. Another consideration is future underground mining. If underground mining is profitable, the pit may need to be shallower. Of all of the investments needed, only mining equipment and the underground mine should be included, and amortization and depreciation should not he included in the study.

Jan 1, 1997

By D. J. Bryden, J. W. Oberholzer

In response to the need for enhanced precautionary measures to safeguard mine workers in collieries from the consequences of methane ignitions in a heading, the coal mining industry has ex- pressed the desire for the development and testing of active on board suppression systems. As overseas systems cannot be used directly in the bord and pillar geometry it is necessary to adapt overseas and local technology to suit local mining conditions, as well as to test such developed systems for their compliance with the expressed needs. As the systems have to be tested in a specific roadway configuration, a facility was developed to enable the testing in South Africa. A surface test facility has been established which can be used to develop and test suppression systems on continuous miners and roadheaders. This facility consists of a tunnel wherein compliance tests can be conducted in simulated underground conditions. A number of methane explosion tests have been conducted in the test facility. The explosions conducted varied in CH,/air concentration (7,5 to 9 percent) and volume (26 to 88 m3). At lower concentrations there was a marked reduction in explosion strength and flame speed. Tests carried out with the Explostop system successfully suppressed the propagation of methane ignitions in both scenarios tested.

Jan 1, 1997

By J. Driscoll

After 30 years of success, Newmont Gold Company has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East Decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East underground at the rate of 700 t/d (770 stpd) for an annual production of over 100,000 ounces. Over 70 underground miners enjoy the estimated 6-year mine life at Carlin East. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

A major Brazilian iron ore producer, SA Minerayao da Trindade (Samitri), has recently completed modifications at two operations which involve the use of Derrick high frequency vibrating screens. Details of these modifications are presented, together with a review of product quality improvements.

Jan 1, 1997

By Ronald J. Searle, Howard S. Latham

In April 1964 the Bureau of Reclamation awarded the first contract for rapid machine excavation of a water conveyance tunnel . Since then the Bureau has excavated seven tunnels with a total length of over 190,000 feet utilizing rapid excavation tunneling machines. Tunnel bored diameters have varied from 9' 0" to 20' 10" (See Table #1) and tunnel lengths from 5,000 feet to 67,000 feet. Driver and cutter units varied from 43 rolling teeth and eight rolling discs mounted on a rotating head driven by five 200 HP 23,000 volt electric motors to 20 discs and one tricone unit mounted on a rotating head driven by two 100 HP 440 volt motors. All tunnels were driven with a laser beam guidance system governing both line and grade. Trailing conveyors and rail haulage systems were used to dispose of the excavated material. Approved Bureau of Mines diesel locomotive engines for waste trains were prevalent power sources supplemented by battery units on some projects. Sandstone, conglomerates, agglomerates, siltstone, shale, and granite were the geological formations encountered, with sandstone and shale the preponderant material . Tunnel support systems utilized were structural steel ribs; rock bolts and metal plates; and shotcrete, or combinations of these. Progress varied from 51-1/2 feet to 154 feet per working day for three shifts, depending on rock material and supports required. One contractor established a record rate of advance of over 400 feet in one day, 1,905 feet in one week, and 6,848 feet in one month. Such diversified experience in underground machine excavation methods presented an excellent opportunity to observe, analyze, and evaluate associated environmental health problems. Also, to develop measures for controlling

Jan 1, 1997

By R. Mensah-Biney

The adsorption of gold-thiourea complex onto a cation exchange resin, Amberlite 252, has been evaluated in a batch stirred reactor. The observed non equilibrium saturation capacity was 3.20 meg Au/g dry resin (620 kg/t) whereas the equilibrium ion exchange capacity was only 0.53 meq/g (103 kg/t). The enthalpy of adsorption was 4 -25 kJ/mole under equilibrium conditions and increased to 20-200 kJ/mole under non equilibrium conditions. Under non equilibrium conditions, the adsorption capacity of the resin decreased with increasing temperature and increasing thiourea concentration and increased with increasing gold concentration. This dependence of adsorption capacity on thiourea concentration and temperature may be a useful tool for elution of gold from the loaded resin. Scanning electron microscopy revealed evidence of deposition of elemental gold on the loaded resin under non equilibrium conditions. The proposed mechanism for "adsorption" of gold-thiourea complex onto this cation exchange resin consists of an ion exchange reaction followed by a reduction of the exchanged gold complex to elemental gold on the surface of the resin.

Jan 1, 1997

By A. J. Basu

Computer assisted mine planning and design applications are routinely used by many Australian mining companies, However, the design process requires human expertise to recognize and evaluate the potential pitfalls. This paper introduces the application of a commercial optimization software (WHITTLE 4D) for strategic planning of an open pit mine in Western Australia. The authors present their experience in intelligent application of the optimization program while incorporating many technical and nontechnical obstacles. This paper provides some guidelines on how to apply the optimization software without loosing sight of practicalities. Moreover, this paper also shows how to build project evaluation guidelines for non-experts.

Jan 1, 1997

By Richard H. T. Garnett

In 1900, placer gold was discovered on the beach of Nome, AK on the southern coastline of Alaska's Seward Peninsula (Garnett, 1991). The site is about 800 km (500 miles) from Anchorage. Nome is connected to Anchorage only by air (daily) and by sea (summer). Total onshore placer gold production from Nome's immediate vicinity was more than 155.5 t (5 million oz). Alaska Gold Co, has continued to produce gold onshore with, until recently, two bucketladder dredges, each of 255-L (9-cu ft) bucket capacity. Small-scale marine dredging for gold has been at- tempted several times this century (Garnett, 1991). Western Gold Exploration and Mining Co. Ltd. Partnership (WestGold) is the only company to have been successful in achieving a significant offshore production. The Nome bucketladder-dredging operation from 1986 to 1990 constituted a unique marine-mining experience in the United States. \Inspiration Gold Inc., WestGold's predecessor, acquired six offshore leases in 1985. The total lease area of 87 km2 (21,551 acres) extended from the coastline to the 4.8-km (3-mile) offshore limit (Fig. 1). Those leases al- ready had been partially explored. Drilling was conducted off the shorefast winter sea ice. Therefore, it was rarely more than 1.6 km (1 mile) from the shore or in water deeper than about 9 m (30 ft). In 1985, estimated reserves comprised of a 5-m (17-ft) vertical thickness of sediments below 6.3 m (20 ft) of water. This meant a mean digging depth below the mean sea level (msl) of 11.3 m (37 ft). It was thought that the offshore Nome deposit possessed a feature that is common with many terrestrial gold placers - the secret of profitable exploitation of the marine deposit lay in maximizing the dredge throughput to minimize the unit costs. The inability of the project to withstand the prohibitively high cost of a new dredge was recognized. So Inspiration Gold purchased a used unit. This was the world's largest ocean- going bucketladder dredge (Fig. 2). Binzn was an 850-L (30 cu ft) bucket capacity dredge that was lying idle in Singapore. Originally constructed in the Jurong shipyard of Singapore in 1979, Bima was designed by Mining and Transport Engineering, a subsidiary of IHC Holland. Billiton Marine used the dredge for tin production at Pulau Tujuh in Indonesia (Dieperink, 1978) before it was laid up in mid-1985. Bima underwent a nine-week refit before departing Singapore on June 4,1986, with 800-t (880-st ) of deck cargo. It was dry-towed for 32 days to Alaska. A slower, less expensive, wet-tow at the authorized 5.5 kmthr (3 knots/hour) would have delayed the dredge's arrival in Alaska untl almost the onset of winter. The 13,000-km (8,100-mile) voyage was made on the deck of Smit Lloyd's "Giant-4" submersible barge towed by its 7.8- MW (10,500-hp) tugboat. The first season's dredging revealed several major shortcomings in Bima. Further repairs and modifications were undertaken at Tacoma, WA. The dredge returned to Nome for the June start of the 1987 summer dredging season. The refitted Bima worked offshore at Nome from 1987 to 1990. It produced 3.67 t (118,078 oz) of gold at an average recovered grade of 824 mg/m3 (0.0204 oz/cu yd). In 1991, the dredge was dismantled and sold.

Jan 1, 1997

By Lee Ann Arrington-Webb

Thiele Kaolin Co. has invested much time and money in achieving and maintaining its IS0 9002 certification. Through a regimen of process control and documentation, routine audits and a commitment to quality management, this kaolin producer is a competitive pigment supplier in a worldwide market. Background In 1987, the International Organization for Standards developed the ISO 9000 quality management system. This series of standards is used as a means to ensure customers that a quality management system is in place. Certification of a company does not mean that an individual product is of high quality. Rather, it demonstrates a supplier's ability to meet its customers' product and service needs. It also shows that a company has documented records to assure product consistency. The ISO 9000 system was begun in England during the early 1980s. During the mid-1970s, the British manufacturing industry was experiencing low quality. In an attempt to boost quality standards, the British government established the BS 5750 standards system. In 1987, BS 5750 was incorporated into ISO 9000. The ISO 9000 series consists of three levels of certification. ISO 9001 is the model for quality assurance in "design/development, production, installation and servicing." This standard applies to companies that rely on research and development to bring products that frequently change to market. ISO 9002 involves "production and installation" only. This standard is relevant to industries that produce a specific product according to specifications - either their own or their customer's. ISO 9003 is the model in "final inspection and test." This standard is the least detailed of the 9000 series. It is also the most applicable to companies that purchase, inspect or sort and resell. The quality system requirements for certification are outlined in the 18 elements of ISO 9002. These include: 4.1 - Management responsibility. 4.2 - Quality systems. 4.3 - Contract review. 4.4 - Design control. 4.5 - Document and data control. 4.6 - Purchasing. 4.7 - Control of customer-supplied product. 4.8 - Product identification and traceability. 4.9 - Process control. 4.10 - Inspection and testing. 4.11- Control of inspection, measuring and test equipment. 4.12 - Inspection and test status. 4.13 - Control of nonconforming product. 4.14 - Corrective and preventive action. 4.15 - Handling, storage, packaging, preservation and delivery. 4.16 - Control of quality records. 4.17 - Internal quality audits. 4.18 -Training. Continuous improvement, though implied in maintaining these requirements, could potentially be included in the quality system requirements in the next revision. The ISO 9000 requirements and documentation system is shown in the hierarchy pyramid (Fig. 1). A company's quality policy serves as the top of the pyra-

Jan 1, 1997

By C. E. Semler

A 5 year test program, involving on-line, in-vessel exposures at Barrick Goldstrike Mines. Inc. has provided valuable information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products have been evaluated. Properties before and after exposure are used to document the performance. Benefits have included the development of a new silicate mortar improved understanding of brick requirements and increased autoclave operating time between maintenance shut-downs. More improvements are expected in the future based on further information from the test program.

Jan 1, 1997

By Krzysztof Filek, Anindya Sinha, Bernard Nowak

Taking into account the possibilities of condensation of water vapour contained in air during its flow through a series of spot coolers as well as formation of eventual fog, a mathematical model of dynamic temperature, specific humidity and degree of fogging of cooled air in underground mining galleries with direct ventilation is developed. In the gallery, there situated various heat and moisture sources both of distributive and of concentrated types. The model is represented by three partial differential equations of first order. The cases of cooling with full as well as with partial air stream flowing through the gallery are distinguished. Owing to the fact that in practical designing, more important is the knowledge of the variation process of temperature, specific humidity and fogging of cooled mine air at steady state conditions, the model is modified to a set of three nonlinear ordinary differential equations. Based on the presented algorithm, the obtained set of ordinary differential equations is numerically solved which enables to: • specify the distribution of temperature, specific humidity, relative humidity and degree of fogging of cooled air in mining galleries; • determine the cooling powers of air coolers for their known locations; • indicate the locations of the coolers of known cooling powers. Exemplary calculations of temperature and relative humidity of cooled air are presented graphically in a number of diagrams.

Jan 1, 1997