Search Documents

By Taghi Sherizadeh, Pinnaduwa H. S. W. Kulatilake

"This paper examines the effect of different geological and mining factors on roof stability in underground coal mines by combining the field observations, laboratory testing, and numerical modeling. Observations at an underground coal mine that uses the room-and-pillar mining method showed several failures of the immediate roof, and is used as a case study. Three-dimensional distinct element analyses were performed to study the intrinsic roof failure mechanisms and to evaluate specifically the effect of in-situ stress magnitudes and directions, discontinuity mechanical properties, and variation of pillar to room size on roof stability.INTRODUCTIONThe lithology of the immediate roof with respect to the underground openings plays an important role in stability of the roof in underground excavations. Laminated, or thinly bedded shale, is one of the most frequently seen overlaying strata above the coal deposits. The bedding planes and interfaces have very low or close to zero tensile strength in the direction perpendicular to the bedding planes, and their shear strength is much lower than of the rock layers. As a result, the bedding planes are much weaker than the rock layers. Therefore, due to the stress concentrations caused by excavations, slippage and separation can easily happen along the bedding planes before initiation of failure within the rock layers.In the past, several attempts have been made to understand the mechanism behind the roof failure in underground coal mines. Most of these earlier attempts were based on empirical techniques and continuum based numerical methods that have limited capability in simulating the response of discontinuum rock mass behavior to excavation. Different factors such as the magnitude and direction of the horizontal in-situ stresses, type and mechanical properties of roof rock, surface topography, geological anomalies, gas pressure, slippage and separation of bedding planes at the roof and floor, entry width and excavation sequences are identified as key factors that could significantly impact the stability of the roof. Among all the aforementioned factors, in spite of its importance, the impact of slip and separation of bedding planes on roof stability has not received enough attention from researchers. In a few available numerical modeling studies, the bedding planes are modeled using the continuum based numerical codes such as ABAQUS (Chen, 1999) and FLAC3D (Ray, 2009). However, since the bedding planes among the roof layers become discontinuous during the numerical analysis, this behavior is most likely not be accurately captured by the continuum based numerical models. Chen (1999) conducted finite element analysis to study the impacts of the roof and coal interface slip and the bedding planes slip in the roof on the stress distribution in the roof strata by using the finite element analysis software named ABAQUS. To avoid the complications associated with the finite sliding between two deformable bodies, he limited his study to the two-dimensional finite element analysis (plane strain). He concluded that the slip and separation of interfaces and bedding planes have significant impact on the behavior of the roof strata and without considering the interfaces, the roof bolt functions cannot be simulated properly by using the numerical analysis methods. Gadde and Peng (2005) performed three-dimensional finite difference analysis using FLAC3D software with strain softening material behavior to simulate the cutter roof in an underground coal mine. Their numerical model was fully continuum and no bedding plane was included in the model. They suggested that the strain softening material model can help to simulate the cutter roof failure up to a satisfactory level (Gadde and Peng, 2005))."

Jan 1, 2015

By Gift Makusha

Pre-feasibility work at Goedehoop Colliery indicated that stooping of the undersized pillars could be undertaken safely and economically. In light of the findings a decision was taken in may 2003 to undertake the project in the 600 area where three panels (628, 630 and 632) were identified for pilot test sites. The findings of the pre-feasibility studies were presented in a paper to the 22nd International Conference on Ground Control in Mining held at Morgantown in 2003 (1). This paper is a progress report for the project 12 months down the line. Work commenced to prepare the sites for mining including, acquisition of equipment, equipping the panels, selecting and training people to undertake the project. Three monitoring sites were set up distributed evenly along panel 628. Each site comprised of a surface extensometer station in the overburden strata adjacent to a pillar underground containing hard inclusion vibrating wire extensometer cells. This combination would be used to record pillar loading ahead of stooping as well as the depth of caving and strata deformation in the goal zone behind the stooping face. In July 2003, support work began to secure the roof and rib sides. The support was required to be at least three-pillar center distances ahead of the mining front to ensure that the effective stooping zone is secured at all times. The NEVID method of pillar extraction developed at Sasol and described in detail by Ismet and Moolman (2) in a Coaltech 20-20 report was adopted for the pilot project. As part of training the selected stooping team was send for a week to Sasol's Bosmanskrans Colliery to familiarize with the NEVID method of stooping. Further training sessions were carried out on site especially on the use of Mobile Roof supports. The first cut was taken on 20 August 2003 by implementing a form of chequerbord mining taking every second row of pillars. Three rows were mined this way which period was considered training to get workers familiar with the new equipment and mining method. On the fourth row the full design span equivalent to mining 4 pillars in a row was implemented taking out all the pillars in successive rows. Production figures gradually increased from 300 to more than 1,000 tons run of mine coal per shift. Panel 628 was mined out at the end of December 2003 and the second of three panels (630) is being mined. Substantial data from the monitoring set up has been recorded since the start of the project. Monitoring will continue to the end of the pilot project and the data will be analysed and fed back into the design tools to improve the design in future undertakings. The pilot project has been a success so far and other old workings are being evaluated for stooping.

Jan 1, 2004

By Bruce Hebblewhite

This paper recognises the 25th year of the Morgantown International Ground Control in Mining Conference, by offering a twenty five year review of ground control in the Australian mining industry ? primarily in underground coal. The paper provides an overview of the developments in ground control design methodologies, practices and products. It not only summarises what has been done, but attempts to highlight at least some of the major issues, significant developments, controversies and areas of contention, plus some of the continuing gaps in our understanding or capabilities as we go forward into the next 25 years. Some of the issues included are in relation to: the development of the high strength bolt and cable reinforcement practices widely adopted today and the contrast between stiff and soft systems; a focus on local detail, at the expense of understanding regional stability concerns; dramatic improvements in the use of, and systems available for underground geotechnical instrumentation and monitoring; some of the ground control management trends, including occupational health and safety concerns, availability of suitably trained staff and legislative requirements; the opposing approaches of the empiricists versus the numerical modellers ? is there some middle ground?

Jan 1, 2006

By Rafal Misa

In order to prevent the formation of mining damage or to reduce its reach, it is advisable to look for technical solutions which would enable effective protection of construction sites from the impacts of underground mining. So far, other authors have mainly focused on developing methods of securing construction sites in order to minimize the damage resulting from underground mining; the issue of geotechnical methods for protecting buildings against mining damage has not been thoroughly covered in those articles. It should be noted that there are relatively few publications directly related to this issue, nor are there practical examples of geotechnical protection. In this paper, a geotechnical solution available for securing building structures is discussed. Trenches presented in this research reduce the size and range of mining deformation. The results of numerical modelling for sample protective solutions, aimed at reducing the impact of mining activity on the terrain surface under various conditions, are presented. The calculations were performed with the aid of the Abaqus 6.10-2 software, based on the Finite Element Method.

Jan 1, 2014

By Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (l) study the interaction between MRS's and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS's have capacities of 5,340 and 7,120 kN (600 and 800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS's help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-scam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4) geologic structures, and (5) panel layout designs and mining practice. Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts ate needed.

Jan 1, 2001

By Michael Kelly

Inertial navigation technology has, for the first time, allowed the position of a longwall shearer to be mapped in three dimensions. Following the success of the technology in highwall mining and successful trials on a longwall face, the Australian Coal Association Research Program (ACARP) commissioned a three year "Landmark" project that aimed to advance longwall automation to the level of "on-face observation" by the end of 2004. This project has been completed with the following successful technical outcomes: Automatic face alignment was achieved, using an inertial navigation-based sensor on the shearer, to accurately measure face geometry and feedback signals used to move OEM (Original Equipment Manufacturer) roof supports. Operational on-line measurement of creep with creep information incorporated into face alignment corrections. Inertial Navigation System (INS)-based enhanced horizon control was bench-tested. Operational broadband communications system to shearer using wireless Ethernet on a commercial-product basis. Acquisition of located coal-face features for use in thermal infrared-based horizon control. Automated Longwall Information System (LIS) developed which integrates information from multiple systems and sensors and provides high quality visualisation and control interfaces. Automatic roadway and face convergence monitoring tools successfully tested. Condition monitoring tools developed and demonstrated for improved face reliability. This paper summarises the outcomes of the project and describes the work being undertaken for the 2 year Landmark Extension project approved in April 2005. Consistent with the conference theme, the paper focuses on the ground control aspects of the project.

Jan 1, 2005

By Douglas C. Peters

Part of the ground control research at the U.S. Bureau of Mines is involved with improving ground control data collection and analysis methods. A geographic information system (GIs) is being used within this research effort to standardize the data collected and provide a common graphical and tabular format and analysis system for researchers to access information on underground coal mines. In addition, GIS's can perform relational analyses on multiple map and tabular data sets which are not possible through map-creation or CAD packages or through data bases alone. In addition to standardizing ground control analyses, there is an increasing need for rapid analysis of ground control data in connection with increasing production rates at longwall mines. The examination of a large number of interrelated parameters and their impact on short-term mine safety and productivity under the time constraints imposed by rapid production requires computer-aided techniques. A GIs provides the means to quickly, quantitatively, and reproducibly evaluate mine-wide conditions. This overview of GI8 techniques for mine data integration and analysis, using a mine in Colorado as an example site, will cover the input of data into a GIs, including mine-wide monitoring system data and general data such as roof control plans and geology. The methods to geographically reference these data sets and retrieve and combine them also will be covered. Automation of such processes briefly will be reviewed to allow future users to automate their mine data analyses.

Jan 1, 1990

By Frank E. Chase

Sacrificial entries, roof slotting, and other tactics have been used to combat high horizontal stresses during roadway development in U.S. coal mines. In Australia, the "pillar extraction on the advance" mining method has been successfully employed as a horizontal stress control technique. The concept of advancing and relieving mine workings through pillar extraction developed from observations that some mines experience difficult ground conditions when advancing and retreating the first panel in a new reserve. However, conditions dramatically improve in subsequent panels. Apparently, the creation of a gob area stress relieves the adjacent panel workings. After much debate and close scrutiny, the first U.S. roof control plan to advance and relieve was approved in 1998, for the Sargent Hollow Mine in Wise County, VA. The major concern was that this mining practice places section personnel inby of the gob. The tentative approval permitted barrier pillar slabbing and removal of the adjacent development pillar during panel development. The intent of the plan was to provide a "stress shadow" for the advancing faces and outby workings to reduce the excessive number of roof falls. Sargent Hollow successfully extracted their first panel by pillaring on advance and retreat mining using posts. Mobile roof supports were employed to extract pillars while advancing the second panel. This paper summarizes Sargent Hollow Mine's experiences with the advance and relieve mining method.

Jan 1, 1999

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By Phillip E. Gramlich

Through extensive practical experience and multiple studies, tensioned roof control systems have proven beneficial in difficult mining conditions. Due to increased mining of less desirable seams, tensioned roof control systems have claimed a progressively larger share of the total number of roof bolts installed in the US coal industry. Each tensioned roof control system has its benefits, but also has problems concerning cost, cycle time, stress concentration, load retention, and protrusion into the mine opening. For example, resin-assisted mechanically anchored bolts (also known as resin point anchor bolts) have a fast cycle time and the potential for high tension loading, but the stress from the mechanical shell is concentrated in a small area and can create concerns with certain roof structures (Zhang and Peng, 2001). Resin point anchor bolts can be difficult to fully grout. The cost of resin point anchor bolts can be an issue; a two-piece resin point anchor bolt has a large number of parts (10) and manufacturing steps (9), adding to its higher cost. Tension rebar bolts can achieve high loads and are easier to fully grout but have longer cycle times. In addition, a high percentage of the installed load can ?bleed off? if the resin mixing time or the ?hold time? before tensioning is short-circuited. Tension rebar bolts can be notorious for protruding into the mine opening, creating an obstruction for man and machine (Figure 1), in particular, with reduced mining heights. A new tensioned roof control system has been developed that doesn?t have moving parts, is cost effective, provides fast cycle times, has a low profile, and is simple t install.

Jan 1, 2014

By Ihsan B. Tulu, Keith A. Heasley, Aanand Nandula

"The objective of this paper is to present the development of a software tool that will assist in an area calculation of the Analysis of Roof Bolting Systems (ARBS) support intensity while incorporating more detailed geology, stress, and intersection span input. In this area ARBS tool, a detailed CMRR distribution can be determined from the available geologic database at the mine. In addition, the overburden and multiple-seam stresses, as obtained from the boundary-element program LaModel, can be converted to a “pseudo-depth” which is then used as the depth input to the area ARBS calculation. Finally, the section-specific intersection spans can be determined from the mine design for input to the calculation. All this detailed area input information for ARBS is handled by the latest version of the Stability Mapping (StabMap) program, which now outputs an area ARBS suggested support density given the required input parameters. This final ARBS grid can be plotted, analyzed and overlaid on the mine map for optimum use in support design and for presentation to production personnel.INTRODUCTIONSince the inception of roof bolts in the 1940s, there has been a lack of a universally accepted roof bolting design method (Mark, 2002; Mark and Pappas, 2012). To address this situation, the National Institute of Occupational Safety and Hazard (NIOSH) developed roof support design guidelines, which were incorporated into a computer program called the Analysis of Roof Bolting Systems (ARBS). These guidelines were based on the effects of roof quality, stress, and mine geometry (Mark, Molinda and Dolinar, 2001). The roof rock quality in ARBS is represented by the Coal Mine Roof Rating (CMRR), the depth is used as a surrogate for the stress, and the intersection span serves to represent the mine geometry (Mark, Molinda and Dolinar, 2001). These three input parameters are used in the fundamental, empirically derived equation of ARBS to calculate a required support density factor, called ARBS, (Mark, Molinda and Dolinar, 2001):"

Jan 1, 2018

By Thomas M. Barczak

The decade of the 90's brought an unprecedented increase in the development of innovative technologies to provide more effective and easier to install roof support in underground mines. To facilitate the application of these technologies to improve mine safety. National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a windows based software program that provides mine operators with a simple and practical tool to make engineering decisions regarding the selection and placement strategy of these various standing roof support technologies. This program includes a complete data base of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. Support design criteria in the form of the required support load density at a specified convergence can he established from four options: ( 1 ) a data base of measured ground reaction data from various mines or ground behavior information inputted by the user. (2) determination of loading requirements based on a detached roof block or rock failure height. or (3) criteria based on the current roof support system, and (4) arbitrary criteria set the by user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user specified support installation- In addition to these performance measures. STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made including graphical analysis of relevant support parameters. This paper describes the STOP and its application to optimize standing secondary roof support systems.

Jan 1, 2000

By J. G. Stewart

Polyurethane injection for the consolidation and control of broken strata is a common practice in the deep mines in Europe. The technology has gained wide acceptance in the coal mines of America since the introduction of RokLok polyurethane binder by Mobay Chemical Corporation in 1977. A popular and growing use for polyurethane consolidation grouting is to control the roof and prevent gob flushing during recovery of longwall face equipment. The technique provides many time and performance-related benefits compared to more conventional methods using wire mesh. Kitt Energy Corporation installed the nation's first 1000-feat longwall face in April and May of 1984. The face completed the first panel in October, 1984, and recovery was begun. Roof Strata consolidation for the recovery was accomplished by a RokLok polyurethane binder infection program designed and supervised by Halbach & Braun Industries. The application provided the most rigorous and demanding test to date of this method's performance and cost-effectiveness relative to bolts and wire screen.

Jan 1, 1984

By John Smyth

Mining through in panel entries and the full face recovery method has been successfully practiced at U.S. Stwl, Mine 50. Suppat of the cut-through entries and recovery room is critical. Traditionally, concrete crib or fly ash cement backfill has been utilized. However, these traditional methods are not feasible at Mine 50 due to the difficulties of the plow face mining through these types of support. Recent development of new cable support systems provides an option for cut-through entry support. Mine 50 and Jennmar Corporation personnel have worked together to design and apply the cable systems in the cut-through entries and full face recovery room to eliminate standing support. To date, a number of full face recovery rooms and cut-through inpanel entries have been successfully mined. The results indicate that the cable systems combined with high capacity shields, have provided sufficient capacity to support the roof. Utilizing the Jennmar Finite Element Analysis (JFEA) computer program (Stankus and Guo, 1996), an analysis of the stress and roof deflection changes as the longwall gradually cut through was conducted. From the finite element analysis data, a supplemental support plan was designed. The history and experiences at Mine 50 are presented. Based on the case experiences and modifications made to the finite element analysis, an improved design criteria for future use has been formulated.

Jan 1, 1998

By Hamid Maleki

Mining in the Book Cliffs Coal Field of Utah has historically been associated with seismicity because of high-stress environments and the presence of stiff, competent rocks. Recognizing the geotechnical risks in this coal field, mine engineers have dedicated considerable resources to the study of mine seismicity. In spite of these efforts, there are no engineering procedures for assessing mine seismicity for a new property and in developing mine designs. This paper presents the results of ongoing geotechnical monitoring and stress analyses at a western U.S. coal mine. The intent is to demonstrate the application of geotechnical methodologies in evaluating mine seismicity and stress-control technologies including evolutions in yield pillar designs for variable topographic conditions of the Book Cliffs Coal Field. We show that narrow yield pillars are quite effective in limiting strain energy accumulation along the gateroads and thus the potential for pillar seismicity. At the same time, the pillars provide sufficient resistance to control roof-floor convergence at the headgate, gradually unloading to residual strength inby the face position. Lagging, nonuniform caving of overburden rocks results in periodic stress concentrations at the tailgate comer. The sudden release of strain energy triggers sudden failure of critically loaded coal in this area of the high stress gradient. The three-entry gate pillar configuration promotes formation of long cantilevers and load transfer to the tailgate, contributing to formation of cutters and coal bumps. The source of seismicity is investigated while simulating slip along three sets of joints in two stiff stratigraphic units during multipanel extraction.

Jan 1, 2003

By Steve Signer

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed several new tools for evaluating roof support performance. A miniature data acquisition system (MIDAS) was developed that can collect readings from up to 16 strain gauges at regular time intervals and store the readings for later retrieval. Three LED lights change from green to yellow, then red, based on the reading levels and/or rates of change of rock movement. This feature can be used to warn miners of rock instabilities. The system can be used with any strain-gauged support (resin bolt, friction bolt, cable bolt) or with a newly developed rock strain strip (ROSS) developed by NIOSH to measure rock strain. A ROSS is grouted in a hole drilled adjacent to the rock support to be evaluated; the deformed shape of the ROSS provides anchorage on either side of the strain gauges. Data from both laboratory tests and field evaluations are presented that describe the capabilities of both the MIDAS and ROSS instruments.

Jan 1, 2003

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By Eric Zahl

Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Spokane, WA, have collaborated with three Western longwall coal mines in an ongoing effort to develop technologies that will aid in providing safe and stable working areas. The goal of the research described here is to develop a stress monitoring system that will provide immediate information to mine managers for making daily safety decisions as areas of poor ground are mined through. Initial work has focused on answering preliminary questions regarding the reliability and use of stress change patterns. Research is concentrated on monitoring horizontal stress because horizontal stress is transmitted over long distances through stiff strata, thus allowing an extended length of entry to be monitored. This paper presents an explanation of the concept, key results from field tests at two mine sites, and a proposed process for imple¬menting a monitoring system. System design layouts, instrument use, data collection and interpretation methods, and processes to present findings to mine staff are described. Additional validation and correlation with actual failure mechanisms are required before this approach can be recommended at ongoing operations. How¬ever, initial results indicate that this approach shows promise in mines prone to bumps and roof falls associated with large stress changes. In particular, analyses of measured changes in horizontal stresses appear useful.

Jan 1, 2002

By Fred Leighton

Outbursts, or the sudden and sometimes catastrophic expulsion of coal and gas into the working area of a coal mine, are a little understood and growing problem. The AE/MS (Acoustic Emission/Microseismic), or rock talk, activity prior to and associated with several outbursts has been recorded using ultrasonic and micro- seismic equipment and has been analyzed by the Bureau of Mines. Analysis of these data indicates that outbursts are comprised of several failures in rapid succession and that anomalous AE/MS data suitable for providing failure warning are generated 15 to 45 minutes prior to the failure. This paper discusses the techniques for recording and analyzing these data and presents sane case histories.

Jan 1, 1982

By A. G. Pasamehmetoglu

The swelling process is an important problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from pedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the pedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992