Search Documents

By Ken Mills

Dartbrook Mine (Australia) works the Wynn seam, which has a moderate propensity for spontaneous combustion. Prior to any mining a commitment was made to place a segregation barrier pillar between longwall blocks 4 and 5. This was to segregate goaves and improve management controls in the event of a spontaneous combustion event within previous longwall goaves. An alternative to the segregation barrier known as a Consolidated Barrier was developed; firstly as a concept, then computer modelled and finally field tested. It consists of a wider than normal chain pillar with concrete Mega-Seals placed in cut-throughs. Permeability and stress measurements were conducted in the surrounding coal of the seal. Remote monitoring took place as the longwall face approached and then passed by the seal. Results indicate that as the longwall retreats past the seal, horizontal stress increases. The additional stress leads to an increase in confinement and a subsequent reduction in permeability.

Jan 1, 1999

By Michael Gauna

Ground fall injuries and fatalities in United States underground coal mines have shown a diminishing trend. Advances in bolting and standing support systems have led to improved safety in underground coal mines. However, the Crandall Canyon Mine disaster in 2007, in which 9 individuals were fatally injured as a result of a widespread collapse, emphasized that proper mine design is a critical issue that must be addressed. The Mine Safety and Health Administration (MSHA) has instituted technical review procedures structured to facilitate the implementation of safe mine designs in underground coal mines. The technical review process and the typical information required are outlined in this paper. The range of mining situations that lead to a technical review, common design methods submitted for review, and their relevant guidelines and limitations are also discussed. Additionally, the relationship between design criteria and mine site historical experience is discussed.

Jan 1, 2011

By William Kendall

INTRODUCTION Stillwater Mining Company, with its two underground, hard rock mines in South Central Montana, is the largest primary producer of palladium and platinum in the Western Hemisphere. Platinum Group Metals (PGMs) are mined from a specific zone within the Stillwater Complex, a layered mafic/ultramafic igneous intrusion, named as the J-M Reef. Over much of the J-M Reef, the economically minable, mineralized horizon is contained at typical horizontal widths of 6.5 ft to 8 ft wide. This feature of narrow mining widths has made it challenging to safely and effectively mine these areas of the J-M Reef using mechanized cut and fill and sublevel sill development mining methods. Mechanization of most or all of the steps of the mining process is important to Stillwater in the continuous pursuit of high standards in safety and health. Mechanized bolting within the J-M Reef ore production headings is an important piece of reaching these objectives. In general, metal/non-metal mining requires varied mining techniques, as compared to more traditional bedded mineral/resource deposits. Narrow vein mining is a selective mining technique that generates a minimal amount of waste material while obtaining the more valuable ore deposits. Drilling and bolting in narrow vein mining has traditionally been performed with air-powered, hand-held ?jackleg? equipment because mechanized equipment is, typically, too large for the selective narrow vein techniques. In addition, traditional hand-held pneumatic equipment provides significant flexibility for small-opening, narrow-vein developments, reducing waste rock handling and improving ore recovery management. The hand-held equipment is also relatively inexpensive to purchase. Due to its simplicity, it is also relatively easy to train operators to use hand-held equipment. Hand-held equipment has been routinely used to safely install ground support and to develop production faces in hard rock mines for many years. Although it is effective, the hand-held equipment requires operator exposure to certain inherent hazardous conditions in the active face/development mine areas. These include falling rock, tripping hazards, bending/twisting/lifting hazards, high noise levels, and chemical fumes from the hammer exhaust. Based on health and safety statistics from the Stillwater mines, operation of the rotary-percussive hand-held equipment adversely affects the long-term health of the operator?continual jackleg operation frequently results in long term damage to hearing, shoulders, arm and wrist joints, and back injuries. This reduces the quality of life for the operator and also results in higher personnel turnover rates for the mining company.

Jan 1, 2014

By Keith A. Heasley

The LaModel program has been used successfully in the United States for many years to design pillars to ensure global stability of pillar recovery operations. However, the recent Crandall Canyon Mine collapse showed that further research was required to improve the design of pillar recovery under deep cover. Toward this end, a new calibration procedure was implemented in LaModel. This calibration procedure prescribes techniques for calibrating the critical LaModel input parameters based on empirical abutment loading and pillar strength, as utilized in the time-tested ALPS and ARMPS programs. The calibration procedure is intended to help guide a novice modeler in choosing calibrated input parameters that produce a standard model that fits within the verification database. However, the rigid parameter specification incorporated in the calibration procedure also removes most of the flexibility in LaModel for specific calibration to the unique conditions at a given mine site. In this paper, a number of the LaModel input parameters are varied outside the bounds of the suggested calibration and the effects on the model results are analyzed. Ultimately, it is shown how the LaModel user might vary certain input parameters to adjust the model to site-specific conditions, while still maintaining the general accuracy and philosophy of the recommended calibration.

Jan 1, 2012

By Dion Pastars

Kestrel Coal has undertaken a surface-to-seam consolidation program of faulted ground prior to longwall retreat in the 304 panel. Micro fine cement is used to improve the rock mass quality and therefore reduce the risk to personnel and equipment whilst increasing previously assumed sterilised reserves. The program is based on information attained from previously successful grouting campaigns in the Queensland coal area and follows the decision making process to ensure there is sufficient spatial permeation of cement across the faulted area. This data is used to assess the residual risk to the business in terms of health, safety and production

Jan 1, 2007

By Jinhua Wang

Based on engineering examples and theoretical analysis, the mechanism of chemical consolidation for fractured roadway surrounding rock was discussed. The chemical consolidating materials and three consolidating methods, that is, capsule, forced infusion and spraying, were introduced. Finally the application effects of the chemical consolidating technique to reinforce the fractured surrounding rock of roadways were analysed.

Jan 1, 1996

By Takashi Sasaoka

A great deal of coal will be left under the final end-walls in Chinese surface coal mines because of lower slope angle in shoveltruck mining systems and larger mining depths. In traditional surface mining systems, the coal under the end-walls will be buried by the inner dumping site, and these coal resources are generally abandoned. Considering these situations, the application of end-wall mining systems was considered in order to recover the residual coal around the end-wall. This mining system can improve economic benefits by exploiting haulage and ventilation roadways from end-walls and utilizing the existing transportation systems. In order to develop the appropriate pillar design methodology for the end-wall mining system, several empirical formulas and methods were discussed based on the formulas developed so far and the mechanics properties of coal and rocks in the Chinese coal mine. From the results of a series of theoretical and numerical analyses, it can be concluded that the coal pillar width calculated by the Mark- Bieniawski formula may serve as an important reference for pillar design in end-wall mining systems, and the end-wall mining system can increase the coal recovery from residual coal resources around highwall and reduce the effect of underground mining operation on slope stability

Jan 1, 2013

By Stephen C. Tadolini

The U.S. Bureau of Mines (USBM) is conducting research to provide alternatives for traditional secondary support methods. These cost-saving methods are proving to afford safer installation, improve entry stability, eradicate material-handling injuries associated with crib supports, and enhance ventilation. In cooperation with Mountain Coal Company, the USBM replaced timber cribbing with high- strength cable supports to provide stability in a gate road that was used for two longwall panels. The support design consisted of 2.1-m (7-ft) full-column resin-grouted bolts and 4.8-m- (16-ft-) long high-strength resin-grouted cable supports. Three support concepts were evaluated: passive, stiff, and tensioned systems. Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during panel extraction. The stress and loading histories for both panels and the abutment and yield pillars were monitored to assist in evaluating the stress transfer and pillar performance in conjunction with the roof behavior. The test results indicated that resin- grouted cable support systems successfully maintained the immediate and main roofs during the extraction of two longwall panels. This paper describes the theory, application, and advantages of resin-grouted cable supports and presents the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1994

By Bowler Jonathan, Lorraine Kent, Tereza Crisu, Stuart Walker, Nicholas Lightfoot

"It has been the practice in Europe to extract the most economic seams first: taking the seams sequentially, top down, to avoid operating within the fractured strata formed by the subsidence trough above previously mined coal seams. In the 1990s, the UK coal industry found itself at a number of sites having to operate over one or more previously mined seams. This led to specific geotechnical challenges with respect to maintaining economic, safe and stable rectangular roadways with rock-bolted support.Within this paper, the current challenges and mitigation strategies of overmining in the UK are described following the completion of a -three-year European Commission-funded project in 2015. The challenges and mitigation strategies are related to:• A case study with overmining of older workings of variable geometry;• Numerical modeling for overmining layout and support design; and• A case study site planning mine layout when considering future overmining.INTRODUCTIONAt the first case study site, case histories were examined for a mine operating at a depth of approximately 700 meters where five longwall panels were extracted above workings 35-40 m below. The overmining of various extraction geometries below led to challenging conditions in areas of high vertical stress concentration. It was found that results from one longwall panel could be suitably used to predict behaviour in a subsequent panel. The experience was used to update previously existing guidelines on the positioning of roadways in relation to subsidence troughs. Existing guidelines recommended that only as a last resort should longwalls be planned to retreat over narrow pillars, or from solid ground into a subsidence trough. Existing guidelines regarding the layout of overmining panels are conservative, and new work indicates that such multi-seam geometries are possible with appropriate support management strategies."

Jan 1, 2016

By Kevin J. Ma, John Stankus, Dakota Faulkner

"Expandable rock bolts are widely used in hard rock mines as an efficient ground control product. However, capacity and service life can be significantly reduced if the metallic body is subjected to corrosion. In some hard rock mines in the U.S., highly corrosive ground conditions exist, and it has been reported that inflatable rock bolts have corroded within a few months after installation. To provide mining industry a cost-effective inflatable bolt and combat the corrosion issues, Jennmar Corporation, Inc., and its subsidiary Keystone Mining Services, LLC (KMS), analyzed corroded bolt samples, identified root causes, evaluated properties of various coating materials, and developed a new inflatable rock bolt, Python M3TM, that is protected with an innovative PyFlexU2TM coating. The new generation Python M3 features improved steel chemistry for reliable performance, modified profile for better inflation, and surface preparation and coating application. The PyFlexU2 is impervious to liquid and air, durable, and UV resistant. With a flexible adhesive, and highly corrosion-resistant undercoating, and a very hard sacrificial surface coating, the PyFlexU2 coating system provides the Python M3 superior protection against chemical corrosion and physical scratch damage. The under-coating has exceptional flexibility and adhesion to prevent coating micro-cracks or fractures after bolt inflation and possesses excellent corrosion resistance to acids (pH <3), alkalis (pH >11), fuels, and salt solvents. The corrosion and scratch resistant PyFlexU2 coating offers very effective bolt protection for extra longevity in highly corrosive environments. The Python M3 coated with PyFlexU2 has been tested in the most challenging conditions, including laboratory corrosion tests in extreme acidic and basic solvents, rock slurry, and borehole scratch insertion tests. With demonstrated corrosion and scratch resistance, the product has been greatly welcomed by hard rock mines in the West and is currently installed in large scale. This paper identifies the root causes of the bolt corrosion, discusses the analysis process, and details laboratory and underground tests carried out on the Python M3 coated with PyFlexU2. The Python M3TM and PyFlexU2TM are subjects covered by pending U.S. Patent Applications assigned to FCI Holdings Delaware, LLC."

Jan 1, 2017

By Gabriel S. Esterhuizen

"Cable bolts are sometimes used in low-seam coal mines to provide support in difficult ground conditions. This paper describes cable bolting solutions at two low-seam coal mines in similar ground conditions. Both mines used support systems incorporating cable bolts as part of the primary support system. Two original cable bolt based support systems as well as two modified systems are evaluated to estimate their ability to prevent large roof falls. One of the support systems incorporated passive cable bolts, while the other used pre-tensioned cable bolts. The results and experience at the mines showed that the modified systems provided improved stability over the original support systems. The presence of the cable bolts is the most important contribution to stability against large roof falls, rather than the details of the support pattern. It was also found that a heavy steel channel can improve the safety of the system because of the ‘sling’ action it provides. Additionally, the analysis showed that fully-grouted rebar bolts load much earlier than the cable bolts, and pre-tensioning of the cable bolts can result in a more uniform distribution of loading in the roof.INTRODUCTIONCable bolting is sometimes used as primary support in coal mines experiencing difficult roof conditions. In low-seam mines the flexibility of the cable bolts allows greater length supports to be installed near the advancing face without the use of couplers. When used as primary support, the cables are typically installed in the same row as fully grouted bolts, replacing two or more of the bolts in each support row. A heavy steel channel may be used as a strap to spread the support load over a greater portion of the roof. Historically, the Mine Safety and Health Administration (MSHA) has not allowed widespread use of partially grouted un-tensioned bolts (e.g., passive cable bolts) for primary support; however, pretensioned cable bolts have been accepted.Various solutions using cable bolts as primary support were attempted at two low-seam coal mines in Western Pennsylvania that were experiencing difficult roof conditions. Both mines originally used fully grouted rebar bolts as primary support and cable bolts as supplementary support. It was found that when a large roof fall occurred, the cable bolts may be contained within the dome of fallen rock. As problematic roof conditions continued to exist, both mines decided to use cable bolts as part of the primary support system. The cable bolts were located near the ribs of the entry, to increase the likelihood that they would be anchored outside the dome of potentially unstable roof. The cable and rebar bolts were installed on a heavy steel channel that acts as a ‘sling’ to distribute the load across the width of the entry. At the first mine, Mine A, pre-tensioned cable bolts were used while at Mine B, un-tensioned cables were used. The two support systems consist of essentially the same support components installed in different patterns and with varying degrees of pre-tension."

Jan 1, 2015

By William D. Gallant

This paper describes a joint cooperative project between the CANMET Cape Breton Coal Research Laboratory and the Cape Breton Development Corporation to conduct a trial of split set cable slings for remedial support in longwall gateroads. Slings were installed in two test sections of the 2 West panel, Phalen Mine which exhibited deformation and the potential for excessive deterioration when subjected to the front abutment of the wallface. Roadway support behaviour was monitored at the trial sites, including lengths of roadway with the standard support of steel sets without remedial support. Observations were made on convergence, loading of the steel supports, loading of the slings, and wallface performance. Comparisons are made of the results obtained from the areas with remedial support to that without, which demonstrates that the slings provided effective remedial support limiting further deterioration of the roof. Improved face end conditions have contributed to increases in safety and productivity of the longwall panel.

Jan 1, 1990

By Thomas A. Cook

The effectiveness of tensioned roof bolt systems has been well researched and documented over the years (Stankus, 1990, 1991, 1997; Guo, 1997; Denton, 2000; Su, 2007). Higher and more consistent installed tension has been shown to improve the beaming effect and associated roof stability especially in highly-stressed, weak, laminated roof strata. To accomplish higher and more consistent bolt-installed tensions, various types of anti-friction washers have been developed and applied to many types of tensioned roof bolt systems. In addition to increasing bolt-installed tension, these washers also provide a lubricating effect that minimizes sparking during the bolt torqueing cycle. The most popular and widely used anti-friction washer configuration consists of a plastic washer that is used in conjunction with a standard hardened steel washer. This washer configuration has performed well in the field in terms of increasing the bolt-installed tension (or plate load) and the related tension/torque ratio (the amount of tension achieved per one ft-lb of applied torque). However, the installed tension does not always maintain consistency. One reason for this inconsistency is that the plastic anti-friction washer sometimes dislodges and shreds or tears before the bolt torqueing cycle is complete. This condition prevents the plastic washer from acting as an anti-friction medium for the entire torqueing cycle. Jennmar Corporation and Keystone Mining Services, LLC, developed the ?TT? washer in early 2012. The ?TT? anti-friction washer is comprised of two zinc-coated (galvanized) hardened steel washers that are joined together with an exclusive polymer. The ?TT? washer has been extensively tested and applied in the Sewickley, Pittsburgh, and Indiana #5 coal seams. The test results indicate an average increase in installed load and tension/torque ratio of 20%. More importantly, the installed load consistency improved, with a significant reduction in the standard deviation of values. This paper will detail the development and testing of the ?TT? anti-friction washer with case studies of actual mine applications.

Jan 1, 2014

By Joao Felipe Costa, Jair C. Koppe, Andre Zingano, Cleber Gomes

"Run-of-mine Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. A large amount of waste results from the coal preparation, and it must be disposed of in waste piles or waste dams, depending on the material size. These waste disposals are the cause of serious environmental problems, not only in the short and medium terms, but mainly in the long term, due to the risk of provoking acid drainage or spontaneous combustion. Waste disposal requirements also demand large areas. Other problems include the pillar and roof stability in abandoned and mined out areas, building of edifices on the old and active mines, and mining under urban areas. To solve these problems simultaneously, backfilling the entries in mined out areas began with two objectives: to understand the mechanical behavior of the filling material and to model the backfilling of room-and-pillar coal mine entries through numerical simulation. Laboratory tests were performed for different filling material (with and without cement) to determine its mechanical properties and failure criteria. Based on this study, it was possible to conclude that the backfill method is a good strategy to improve the ground stability in room-and-pillar coal mines for the long term, especially for weak coal seams, and to reduce the quantity of material on waste piles on the surface.INTRODUCTIONRun-of-mine (ROM) Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. Two types of waste are associated with power plants that bum coal for energy generation: 1) the waste from the coal preparation plant and 2) the ash from the power plant after coal burning.The Brazilian coal ash content in the ROM coal is between 45 and 55%. The clean coal is 20 to 30% ash for 4,500 kcal/kg (18,000 BTU). The coal preparation plant recovery is only about 35%. Santa Catarina State (SC) produces about 7 million tons/year of ROM coal, which results in a total of 4.5 million tons of waste. This is a large amount of waste that must be disposed of in waste piles or waste dams, depending on the material size. The waste and ash content is represented by silicate materials, such as clay and sand, and by sulfide materials, like pyrite and organic sulfur (between 1and5%)."

Jan 1, 2010

By Stephen P. Signer

A method to assist in the evaluation and selection of roof bolts using in situ measurements of roof bolt loading has been developed by researchers of the Spokane Research Center, National Institute of Occupational Safety and Health. Both axial and bending forces are measured by strain gauges at many locations along the length of fully grouted bolts during various stages of mining. This information is then used to ( I) predict bolt loading for variations in bolt spacing, grade, and diameter, (2) calculate the design changes necessary in zones where bending loads are high, and (3) determine if bolt length is adequate. Results from several case studies of full-column bolt loading in coal mine gate roads are used to illustrate the design method. This knowledge will give design engineers a tool for the selection of roof support systems that will improve underground safety by reducing roof bolt failures.

Jan 1, 1997

By Abdolreza (Reza) Osouli

Determining the roof stability condition of underground coal mines in the Illinois Basin is sometimes very challenging. The roof stability of Illinois mines are mostly affected by two types of shales: Anna Shale and Energy Shale. These layers are sometimes weak in parallel bedding when subjected to horizontal stresses. The roof rocks in the Illinois Basin are are typically more moisture sensitive than the other coal fields. In this study the geotechnical properties of some of the shale units as well as limestone layers will be presented. The geotechnical properties of roof rocks consist of moisture content, unconfined compressive strength, slake durability, indirect tensile strength, and point load tests (Axial and Diametral). The correlation of indirect tensile strength versus diametral point load strength as well as unconfined compressive strength versus axial point load test are explored and discussed. These correlations will help in identifying the roof mass index and planning appropriate roof control measures. This study also evaluates the application of CMRR rock mass index for an Illinois coal mine.

Jan 1, 2014

By Eric Keller, Jamal Rostami, Wenpeng Liu

"Roof and rib instability is an important issue in underground mining. To optimize ground support design, enhance ground stability, and reduce the possibility of roof or rib failure with minimal use of artificial ground support, it is essential to have an accurate understanding of ground conditions. This includes the location of voids, cracks, and discontinuities, as well as information about the different strata in the immediate roof. This paper briefly introduces ongoing research on void detection by using the roof bolter feed and rotation pressure. The goal of this project is to improve the sensitivity of detection programs to locate smaller joints and reduce the number of false alarms. This paper has presented a brief review of the testing procedures, data analysis, logic, and algorithms used for void detection. In addition, this paper has discussed the results of preliminary laboratory tests and statistical analysis of the data from these two drilling parameters used for void detection.INTRODUCTIONRoof falls are one of the most serious and frequent accidents in underground mining. Each year, personnel are injured or killed because of roof falls. Equipment can also be damaged when this occurs. According to Mine Safety and Health Administration statistics collected from 1999 to 2008, ground falls were the largest cause of fatal accidents in underground coal mining, causing around 40% of all fatalities (NIOSH, 2015a). Out of 8 to 10 fatalities and over 800 injuries are recorded each year in underground mines, there are nearly 2,000 reportable non-injury ground falls every year (NIOSH, 2015b).Certain features in the ground, such as voids, cracks, and discontinuities, are significant factors that cause roof support failures and roof fall accidents. Currently, several manufacturers provide smart roof bolters with limited capabilities for void detection. While successful in many instances, in laboratory experiments, the existing void detection systems have limited success in detecting void openings that are less than 1/8 inch This limited success was observed in testing concrete blocks with gaps in between, simulating a rock medium with voids. Detection programs have missed some voids, while, in some cases, they have shown false detection. These algorithms need to be more accurate in sensing voids to improve the capabilities of these programs."

Jan 1, 2016

By Pengfei Wang, Guorui Feng

With increase of cover depth, dynamic incidents, such as large gateroad convergences and coal bursts, are frequently encountered when mining deep longwall panels. It would be more adverse due to large inclination of the coal bed. Because of the shearer and armored face conveyor (AFC) sliding downhill, toppling of shields, disconnection of AFC to the stage loader are related to it. Tangshan coal mine is a typical deep, inclined coal mine situated in the east of China. The split-level longwall panel layout is being adopted for mitigating problems above, where tailgate entries of longwall panels are driven below gob edge and along the floor, while headgate entries are driven along the roof. Wire mesh and steel sets have been used empirically for support for tailgates for about a decade, which reduces the tunneling speed. In view of this fact, the paper serves to investigate the proper adjustment of the tailgate locations and to analyze the resulting stress and yield conditions according to support strategy. First, field measurements and observations were carried out. Stress data distributed within surrounding rock mass were obtained, especially within the roof since the roof consists of only a coal sheet with a thickness of 2–4 m. Roof pressure of the tailgate represents the pressure at the gob edge since it is below the gob edge. The convergence data were also collected. Numerical modelling using FLAC3D™ was conducted and validated by side abutment stress data. The double-yield constitutive model was used to simulate the gob. The finalized tailgate layout and design were determined through comparison of three scenarios. The research in this paper can help engineers choose the proper tailgate layout and support strategies for coal mines that are going to adopt a split-level longwall panel layout for mining deep, inclined longwall panels.

Jan 1, 2018

By Chris Mark

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends, If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the "full resistance zone" of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. This paper describes recent studies using short encapsulation pull tests in the U.S. Tests were conducted in the National Institute for Occupational Safety and Health (NIOSH) Safety Research Coal Mine at Bruceton and at underground mines in Pennsylvania and West Virginia. The study found that the SEPT can be used to make a simple evaluation of resin bolt anchorage. Suggested procedures for conducting SEPT are included. The study also confirmed that poor anchorage can be an issue, particularly where the roof rock is very weak. Some simple techniques for improving anchorage, and thereby the effectiveness of fully grouted bolts, are discussed.

Jan 1, 2002

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r&apos; panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987