Search Documents

By Gabriel Esterhuizen

The roof rock in underground limestone mines in Northern Appalachia can be subject to high horizontal stresses in spite of the shallow depth of the workings. The high stresses can cause roof stability problems. The National Institute for Occupational Safety and Health staff have observed a distinctive asymmetrical mode of failure at the pillar-roof contact in two underground stone mines, which is different from the typical failure mode observed in response to excessive levels of horizontal stress. A dip of greater than 5° was identified as a possible cause of this mode of failure. Numerical model experiments showed that an increase in the dip of the workings can cause an increase in the stress at the up-dip comer of the roof beam. A case study is presented in which failure at the pillar-roof contact was observed where the dip of the workings was 7° in a high horizontal stress field. Numerical modeling showed that the relatively small dip of the workings could have induced stresses changes in the immediate roof that would explain the failures. The model results also showed that this mode of failure is less likely to occur if the limestone pillars contain weak bedding planes that provide stress relief. In addition, the results showed that for the conditions at the case study site, the stress in the roof beam was not sensitive to the thickness of the roof beam or to the excavation span. The high horizontal stresses at this site are an important contributing factor to the observed failures.

Jan 1, 2004

By Syd Peng

It is necessary to fully understand roof geological features in order to design a proper roof support system for underground coal mines. These geological features include: rock type, rock strength. rock layer interfaces, voids, cracks, and bed separations. Traditionally, engineers have relied heavily on the use of surface borehole log data to identify geological features. Since surface boreholes very expensive to be drilled in close spacing, log data are often insufficient to provide detailed information on the roof geology. Recent advances in control technology have made a large amount of roof bolter drilling data available to mine personnel. These data can be obtained during normal roof bolt installation cycle with little or no interruption in mining operations. This research project has developed several methods to identify geological features in a mine roof from measured drilling parameters. Power trend line analysis can be used to locate discontinuities and interfaces in mine roof. Power averaging can be applied to determine the relative strength of roof strata. Thrust trend line analysis can be used to locate fractures in mine roof. The results of these methods are combined to produce a mapped roof geology In a production environment, manually interpreting and managing collected drilling parameters is not practical since hundreds of holes will be drilled during a production day. A new software package, MRGIS, has been developed to allow mine engineers to make use of the large amount of roof drilling parameters for roof support design. An actual underground test site is presented to demonstrate the analysis and display capabilities of MRGIS.

Jan 1, 2003

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By M. M. Zarnan

This paper presents the results of s study involving characterization of ground subsidence of abandoned lead-zinc mines in northeastern Oklahoma. Two coordinated efforts were undertaken: (1) collection and analysis of available data such as driller's logs, geologic cross-sections, structure contour naps and stratigraphic sections, and (2) development of a numerical (finite element) technique for prediction of collapse and mine subsidence. An in-depth analysis of a major collapse in the region was conducted. The factors which contributed to this collapse were identified.

Jan 1, 1989

By Shuangsuo Yang

Based on field observations and physical modeling of simulated materials, the dynamic equilibrium principle on the whole interaction process between the surrounding rocks and support of large deformation roadways in coal mines has been developed. It explains the methods of forming the bolted strata and its changing load capacity with deformation. It also points out the factors and conditions for forming the bolted strata as follows: (1) many entries in coal mines are subject to large deformation. During their service life, it goes through the following process, elastic > plastic > fiacture > broken > loosening, etc. During this dynamic process, the mechanisms of supporting structure are changing and therefore the interaction between support and rocks experiences a process of dynamic equilibrium. Furthermore, the required supporting force for stabilizing the surrounding rocks shows overall decreasing trend; (2) the bolted strata is a special supporting structure consisting of bolt, rock skin protection devices and rock strata within the bolted horizon. As deformation increases, the supporting structure of the broken strata within the bolted horizon experiences a process of periodic change, from equilibrium > not equilibrium > equilibrium. Corresponding to this change, the supporting capacity of the bolted strata also fluctuates and gradually decreases; (3) under the bolted strata, the stability of a large deformation roadway is dynamic and step-wise; and (4) the formation of bolted strata, especially bolted broken strata depends on the existence of compressive force. Supporting the bolted strata is not constrained by the quality of the surrounding rocks. It has broad range of application.

Jan 1, 2005

By Axel Preusse

Underground coal mining can cause seismic events. There is currently no way to predict such phenomena reliably, in particular stronger events. That is why, according to the current state of the art, empirical methods are employed in this field. Some assessment criteria, which relate to the geological and mining situation and either stimulate or rather help to avoid seismic events, are presented in this paper. These criteria are examined for a practical mining situation in Germany, with a view to estimate possible seismic events.

Jan 1, 2009

By Yanfa Gao

Clusters of underground openings were developed around the shaft bottom of Tangshan Mine. They were deep and located in soft rock strata. After development, those openings have been subjected to considerable deformation and damages. A combined supporting method including grouting and bolting, shotcrete lining and brickwork was used. This paper analyzing the theories on which this supporting method was based. A new theory called "Disturbed Creep" was developed for deformation prediction of openings surrounded by strata subjected to stresses close to limiting or failure strength. Keywords ground pressure, deep mine, soft rock, stability control

Jan 1, 2002

By Paul A. Lu

This paper proposes an unconventional, simple, and practical method of measuring mining-induced around stresses with hydraulic borehole pressure cells. The method is a direct ground stress measuring technique. It does not require the value of deformation modulus for back-calculation of stresses; instead, it directly measures the ground stress in situ. The applicability and practicality of the technique are shown by two case studies. The technique may be applied to monitoring a stress build-up that may lead to mine roof failure or to rock and coal outbursts.

Jan 1, 1984

By M. Terry Hoch

This paper presents information on low-coal ATRS systems that are now in use. A study was conducted consisting of an in-mine evaluation of ATRS- equipped roof bolters capable of bolting in seams below 42 inches. Machine manufacturers, MSHA personnel, and bolter operators were asked to assist in reviewing the operation of various low- coal ATRS systems. Features of each system are outlined and operational problems and limitations of each are analyzed. Specific applications, such as ATRS-equipped bolters designed for use with auger-type miners, are also examined.

Jan 1, 1988

By Edward S. Custer

Recent investigations of mine roof falls have demonstrated that roof failures are generally associated with geologic conditions. The roof falls can be predicted by using the techniques of depositional modeling for the coal bed and roof rocks, and by lineament analysis. The ability to predict potential roof failure areas will allow the engineer and mine planner to develop a mine plan to avoid the roof failure areas and thus reduce overall mining costs. The ability to avoid roof failure areas also will permit maximum recovery of the coal resources.

Jan 1, 1981

By Yi Luo

The efforts to mitigate longwall subsidence influences on various residential and farming structures by many coal mining companies have been successful in the recent years (Luo, et al, 2003). The successes were largely dependent on the accurate subsidence predictions, correct assessments of potential influences, appropriate design and implementation of the mitigation measures. However, such efforts for protecting large industrial structures are still very rare. In this paper, the successful assessment and mitigation of the subsidence influences associated with a very intensive dynamic longwall subsidence process on a large workshop are presented.

Jan 1, 2005

By H. J. Siriwardane

This paper presents results from three case studies involving longwall mine panels at which the measured ground movements were compared with the numerical model predictions based on the finite element method. A new approach called the "displacement approach" was used in this study. The general concept of this method is based on the assumption that total roof collapse occurs behind the mine face as it advances. This assumption appears to be true for almost all longwall mining conditions. The prediction based on the numerical model appears to compare well with the measurements.

Jan 1, 1988

By S. S. Rowland

Good afternoon, ladies and gentlemen. It is a pleasure, for several reasons, to be here at this 13th International Conference on Ground Control in Mining. Of course it's always a pleasure to be able to see and reacquaint myself with many long-time friends; but it's also a pleasure, or 1 should say worthwhile, because I take something back with me, some knowledge about mining that lets me do my job better and more safely. if I can do that, I've accomplished my purpose in being at a conference such as this. This conference is a little different, though. I have to earn my stay. I have to earn it by telling you a story; a story about mining through a mile of rock to get from one coal seam to the same seam on the other side of an ancient river channel; a story about mine personnel taking over the job from a contractor; a story about having to mine through two faults after the hard part was supposed to be over, but, most importantly, it's a story about how it was accomplished successfully and safely by a group of ordinary coal miners possessed with determination, belief in themselves, and a "can do" attitude. If you can take any part of my story and use it to do your job better and more safely, then I will have accomplished my purpose in being here today. Kerr-McGee Coal Corporation's Galatia Mine is located in Southern Illinois near the town of Harrisburg in Saline County, about 350 miles south of Chicago and 120 miles southeast of St. Louis. Construction of the mine began in 1982, and the first coal was shipped in 1984 from the Harrisburg No. 5 Seam, 550' below the surface. Mining began in the Herrin No. 6 Seam, 100' above the No. 5 Seam, on April 1, 1985. Mining in both seams began by using the room-and-pillar method. In 1989, the No. 6 Seam was converted to longwall mining, as was the No. 5 Seam in 1992. Today, all mining is done by the longwall method except for the required development work, which is performed by continuous miners. A heavy-media preparation plant with a 4.2 million-ton annual clean-coal capacity processes the coal. By the end of 1994, with annual production now exceeding 4 million tons, we will have shipped over 30 million tons of steam and metallurgical coal throughout the United States and the world. Most of the coal has been used as the primary source of fuel to generate electricity for the city of St. Louis. The No. 5 Seam coal can be used as a semi-soft coking coal or as a high-Btu, relatively low-sulfur steam coal. Its use allows utilities to comply with Phase I of the Clean Air Act Amendments of 1990 without installing flue gas desulfurization units or blending with other coals. The Herrin No. 6 Seam is a high-Btu, medium-sulfur steam coal that requires blending to meet Phase I requirements. Because the No, 6 Seam coal does not meet the Clean Air Act Amendments' Phase I compliance standards, we were forced to cease mining operations in the No. 6 Seam, leaving 170,000,000 tons of minable coal in the ground. Last month the Galatia Mine became a single-seam operation mining the Harrisburg No. 5 Seam only. The Clean Air Act Amendments of 1990 and the resultant S02 emission limitations on electrical power generation plants effectively eliminate, beginning in 1995, the near-term potential for profitable mining of the Galatia Mine's high sulfur Herrin No. 6 Seam coal. Because of the Clean Air Act Amendments, it is virtually impossible to market high-sulfur coals like the No. 6 coal unless the mine location and mining conditions enable greatly depressed sales prices to cover costs. We, along with the majority of

Jan 1, 1994

By Gamal Rashed

Coal bump is a sudden manifestation of the release of strain energy stored in a coal pillar (Peng, 2008). It is a very serious mining hazard that adversely affects the safety and productivity of the mines. Several case histories in mining have described coal pillars or faces of coal failing violently with an accompanying ejection of debris and broken material into the working areas of the mine (Campoli, 1987; Osterwald, 1962; Peperakis, 1958; Garvey and Ozbay, 2013). These failures resulted in large losses of life and total collapses of entire mine panels (Chase, Zipf, and Mark, 1994; Zingano, Koppe, and Costa, 2004). There are questions in the literature about whether or not the coal itself plays a significant role in bump. Rice (1935) mentioned that structurally strong coal is one of the key factors for bump; however, the strength of the Pocahontas #3 coal seam is low, and it bumped. Moreover, it is not obvious in the literature whether the strength of the tested coal samples is the inherent strength or if it is influenced by the shape or the size of the specimen. The main objective of this paper is to answer the following question: To what extent does the mechanical properties of the coal have an impact on the potential for violent failure? The best approach to answer this question is to compare the mechanical properties of two kinds of coals from bump-prone (Utah coal-Sunnyside seam) and non-bump-prone (WV coal-Sewickley seam). This comparison includes uniaxial compressive strength, modulus of elasticity, shear strength (cohesion and friction angle), and the burst index.

Jan 1, 2014

By Charlie Li

A cut-and-fill mine stope, located at a depth of about 1000 m in a lead-and-zinc mine, was closed down because of large roof convergence and fractures appearing on the hanging wall. The instability problem was owing to the relatively low strength of the rock subjected to high in-situ stresses. Extra reinforcement was required to secure the stope so that the remaining ores in the stope could be mined. Assessment of the fracture mode in the country rock surrounding the stope was carried out and then the reinforcement de- sign was worked out. It was proposed that the unstable section of the stope would be reinforced by bolt-shotcrete ribs as well as selective long bolts. The philosophy of the design was to hold up the fractured country rock by bolts and shotcrete so that a load-bearing arch could be formed in the roof and in the hanging wall. Six shot- Crete ribs were set up in the unstable section of the stope. Displacement measurements showed that the roof convergence reduced from about 2 &day to the ordinary creeping level, about 0.25 &day, immediately after the reinforcement operation. Six month later, the hanging wall collapsed into the stope in a place just outside the reinforced section, which indirectly proved the effectiveness of the bolt-shotcrete ribs in reinforcing the fractured country rock. This case showed that an appropriate rock mechanics assessment would form a solid base for reinforcement/support design. It also provided an evidence for the philosophy of the reinforcement by bolt-shotcrete ribs - establish a load-bearing arch in the rock.

Jan 1, 2005

By Richard C. Repsher

The U.S. Bureau of Mines has developed a method and device designed to detect lose rock material in underground mines. The technology is designed to be an aid to mine workers in detecting hazardous roof conditions in underground mines which can complement or replace the traditional roof sounding techniques where the miner relies on experience to determine whether rock conditions are sound. The leading cause of accidents and fatalities in underground mines is falls of lose rock pieces or rock slabs from the mine roof. The device is an electronic roof sounding device that acoustically determines the integrity of mine rock. In previous research the Bureau of Mines found that loose rock, when impacted, vibrates at a much lower frequency than intact rock material. A major problem in determining rock stability using this technique has been the repeatability of the matt signal. This difficulty baa been greatly reduced in the current design by measuring the power spectra contained in two separate frequency bands of the signal produced by striking the rock in question. The ratio of the energy contained in each band is computed. This process minimizes any striking force differences, producing accurate, repeatable results for solid rock as well as loose, drummy material. The prototype has been successfully- tested in a variety of underground environments including coal, uranium, molybdenum, silver and salt. The technology has been investigated by the U.S. Mine Health and Safety Administration and the Department of Energy for use in detecting detached tunnel lining areas in nuclear repositories. The paper will discuss the technique, applicable results, and future applications.

Jan 1, 1990

By Chris Kelly

The Monroe County Quarry is an open pit granite quarry located near the town of Bolingbroke. Monroe County. Georgia. The quarry has been in continuous operation for approximately 10 years. The quarry covers approximately 27 acres and has an annual production rate of 1.0 million tons. On the morning of April 26. 2000 a sudden rapid highwall failure occurred at the west end of the north wall of the quarry pit. The failure occurred approximately one hour after a three inch-wide crack was observed in an access road located at the crest of the highwall. No indications of failure had been observed prior to the development of the crack. The active mining area had been at the base of the failed area. The pit was successfully evacuated prior to the failure and there were no losses of either personnel or equipment. The amount of failed material was estimated to be in excess of two million tons. In order to ensure a safe working environment at the quarry a slope monitoring program was established in the area of the failure. The program consisted of using an EDM survey instrument to periodically measure the location of survey prisms installed at carious points on the north wall. The locations of the prisms were recorded over several months and changes in location were analyzed in order to identify and characterize the movement of the failed mass. The results of the analysis provided a basis for recommendations regarding access to various areas of the quarry. This paper discusses the factors contributing to the failure, the method of post-failure slope monitoring, anti the interpretation of the monitoring data.

Jan 1, 2002

By V. V. Nazimko

Abandoned coal mines cause subsidence and structural damages. Shallow abandoned mines induce the most severe and harmful damages. In addition, they produce time-dependent subsidence which is difficult to predict. Backfilling of underground cavities with waste materials have been used to prevent the time-dependent subsidence or to mitigate its effect. However, this procedure is expensive. A new drill and blast technique has recently been proposed to prevent surface damage from time¬dependent subsidence over abandoned mines. It utilizes the principle that blasting in the caved rock and roof in the vicinity of a cavity will dilate the ground and create a self-supporting effect owing to increase in the volume. Physical modeling has demonstrated that artificial dilation of caved rock using the drill & blast technique creates positive effects due to the following sequence of events: the dilated rock creates a supporting effect for the suspended rock strata and reduces its span which decelerates 3.4 times the process of caving. The roof span is reduced by the next caved layer, which causes the hole boundaries to incline to each other. This effect converts the process of caving from a developing mode to a reduction mode. Finally, the sinkhole zone assumes a triangular shape with a negative angle of draw 64-700 in contrast to a rectangular shape of the chimney zone for natural caving. Vertical dimension of the triangular zone is 3.87 times of the room height. Final surface subsidence decreases at least 2.09 times; displacement 1.31 times, slope 2 27 times; curvature 3.42 times, horizontal strain 1 21 times in comparison to natural caving of the ground over an abandoned mine.

Jan 1, 1999

By Dennis R. Dolinar

Controlling coal mine roofs subjected to high-horizontal stress conditions has always been difficult and uncertain. Traditional supports such as wooden cribs and posts, concrete donut cribs, and standing supports collapse and fail when the roof and floor move horizontally as mining progresses. The former U.S. Bureau of Mines (USBM) (currently the U.S. Department of Energy (DOE)), in cooperation with Western Fuels-Utah, Incorporated, conducted research to provide an alternative for traditional secondary support systems in a 3-entry gate road system subjected to high horizontal movements. The support system used in several other coal mine operations, consisted of internal high-strength galvanized resin-grouted cable supports. The system virtually eliminates the necessity for external crib, timber, or concrete supports. The support system consisted of 2.4 m (8 ft) full-column resin grouted bolts and 4.8 m (16 ft) long cable supports installed in conjunction with wire mesh and "Monster-Mats." Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during first and second panel extractions. Additionally, cable trusses were installed on the longwall headgate to protect the coal conveyance system from roof and pillar falls created by the formation of cutters and gutters. The test results indicated that the designed support system successfully maintained the roof during the extraction of two longwall panels and dramatically reduced the cost of secondary support. This paper describes the theory of high-horizontal roof movements, the advantages of vertical cable supports and cable trusses, and presents the roof and cable measurements made to assess the support performance during longwall retreat mining.

Jan 1, 1996

By Dan Payne

Roof falls and other ground control incidents make up a significant portion of fatal accidents in underground mines. BHP Billiton has undergone a review of all fatalities in their operations and divided these into 10 fundamental categories of which underground ground control is one. Each underground roof fall fatality was investigated and the root causes workshopped to develop a protocol for the control of fatalities due to falls of ground. This protocol sets out 22 requirements which each BHP Billiton underground mine site must comply with. This paper describes the development, requirements and application of the protocol within BHP Billiton.

Jan 1, 2006