Search Documents

By Brent A. Slaker, Michael Murphy, John Ellenberger, Erik Westman

"Photogrammetry, as a tool for monitoring underground mine deformation, is an alternative to traditional point measurement devices, and may be capable of accurate measurements in situations where technologies such as laser scanning are unsuited, undesired or cost-prohibitive. An underground limestone mine in Ohio is used as a test case for monitoring of structurally unstable pillars. Seven pillars were photographed during four visits over a 63- day period. Using photogrammetry, point clouds of the mine geometry were obtained and triangulated surfaces were generated to determine volumes of change over time. Pillar spalling in the range of 0.29–4.03 m3 of rock on individual rib faces was detected. Isolated incidents of rock expansion prior to failure, and the isolated failure of a weak shale band, were also observed. Much of the pillars remained unchanged during the monitoring period, which is indicative of proper alignment in the triangulated surfaces. The photographs of some ribs were of either too poor quality or had insufficient overlap, and were not included. However, photogrammetry was successfully applied to multiple ribs in quantifying the pillar geometry change over time.IntroductionAdequately measuring underground rock mass movements is integral to understanding how rock masses behave and how to interact with them safely and efficiently. Many modern measurement techniques employed in underground mining environments rely on point measurements, such as through extensometers or borehole relief methods (Christiansson, 2006). These techniques, while commonplace, do not provide a comprehensive view of how the rock mass is behaving. The dynamic changes in stress states underground, coupled with the mechanical uncertainty of rock masses, near active excavations, creates a need for measurement systems which better capture the behavior of the rock mass. Photogrammetry is a technology capable of producing the wide-area displacement measurements required for a comprehensive understanding of rock mass movements.Digital photogrammetry is a means of obtaining threedimensional point clouds from digital photographs. By finding the same point across multiple images, all viewing an object from different angles, the location of that point in three-dimensional space can be inferred. Close range digital photogrammetry (CRDP) is photogrammetry applied to measuring objects or scenes less than 100 meters away (Atkinson, 1996), and is used for various functions in underground mining environments. These uses include, but are not limited to, mapping fracture networks (Kim, Kim, & Won, 2005)(Somervuori & Lamberg, 2010), characterizing fractures (Styles et al., 2010) and measuring volumes of blast rock (Heal, Hudyma, & Potvin, 2004)."

Jan 1, 2015

By David W. Evans

"Induced hydraulic fracture of strata during roof bolt installation is a potentially prevalent, but masked phenomenon within the underground coal industry. Previously reported resin testing programs (McTyer et al., 2014) examined the relationship between resin mixing effectiveness and varying bore hole diameter. The methodology employed within this earlier test program facilitated a further critical area of research – the measurement of back pressures generated within the bore hole during standard rock bolt installation practices. Experimental data has indicated that fluid resin can be pressurised to levels where it exceeds the compressive strength of the strata, inducing hydraulic fracture within the immediate area of the bolting horizon. The routine cycle of roof bolting serves to propagate this effect, progressively fracturing and delaminating the roof during mine advancement. This masked phenomenon can lead to a perception of difficult ground conditions - mining efficiencies and costs are therefore affected, with increased needs for additional support subsequently required to restabilise the inadvertently damaged roof.Further analysis of the parameters associated with resin bolt installation has now been conducted, assisting in the development of an empirical relationship between bore hole pressure, bore hole diameter and bolt insertion times. This relationship has been analysed for 15:1 ratio resins and 2:1 ratioresins, within 28mm and 30mm boreholes. Further to this, load transfer performance has been comparatively assessed for both 28mm and 30mm boreholes, suggesting that for 2:1 resins, acceptable resin mixing and load transfer can be obtained within a 30mm bore hole. The combination of 2:1 resins, utilised within a 30mm bore hole, may well provide the optimal solution to reduce the risk of hydraulic fracture in weaker strata during resin bolt installation.INTRODUCTIONA growing number of industry papers have previously investigated areas of concern associated with the performance of cartridge style resins in roof bolting, predominantly focussing on the effects of plastic film gloving, inadequate resin mixing and the pressurisation of resin within the bore hole. These three effects have a critical influence on the load transfer of the steel bolt element, through the cured resin and into the surrounding strata.Gloving occurs due to the plastic film of the resin cartridge partially encasing or wrapping around the steel roof bolt element – a known phenomenon over many years (Pettibone, 1987). The plastic film creates regions of discontinuity between the bolt, cured resin and borehole, reducing effective load transfer into the strata. Experimentation conducted into the effects of bolt ends fully encased by plastic film (Pastars and MacGregor, 2005) revealed that load transfer can be reduced by 85 to 90% in worstcase occurrences. It is also known that the aggregate filler size used within the resin can assist in shredding and breaking up the plastic film – this effect was observed in a previous study on resin mixing effectiveness (McTyer et al., 2014)."

Jan 1, 2015

By Joe E. Bryan, John P. McDonnell

"Underground mine rib stability is an ongoing safety issue in all mining applications. Rib-related accidents present at least as many problems as roof-related ground control. Underground coal mine rib safety is continually emphasized as a primary safety concern at every mining operation. The application of rib support materials is increasing as more difficult mining conditions are experienced due to deeper cover, more variable depositional environments, thicker seam heights, and multi-seam mining effects. As the coal seams become thicker, the need for rib control increases. A variety of rib control methodologies has been documented and research continues on mine design methods and support techniques to reduce or eliminate rib-related accidents.This paper presents an alternative rib bolting technology using proven conventional rib support systems that allows mine personnel to more efficiently install rib support during development operations. This alternative rib bolting method allows for additional rib support with a single support installation.INTRODUCTIONRib control continues to garner the watchful eye of both concerned operators and government officials due to many factors: inherent safety within entries and crosscuts, actual rib stability history, safety improvement, cost control, improved mining methods, and maintaining production goals. As demonstrated through many years of actual practice, desired outcomes can be achieved by scrutiny, innovation, and combining improved practice methodologies.Rib surface control continues to be a necessary part of the production process. However, production and safety issues persist at the point of installation using current control apparatuses and methods to install rib controls. Among others, current issues of rib control are quantity of bolts required, overall time required for installation, ease of apparatus installation, flexibility of the system for appendage installation and operator exposure. A need exists to decrease the time miners spend installing rib control apparatuses, while increasing the safety of such installation processes. At present, installing rib control devices (primary rib bolts, plates, mesh, and, in most cases, secondary rib bolts and plates) is performed in a very congested area and is time-consuming process at the primary coal-winning area: the face. The MatLok system addresses these problems."

Jan 1, 2015

By David A. Newman

In the 1950s, an underground limestone mine in the Camp Nelson Formation was developed from an outcrop exposure. The Camp Nelson Limestone met the requirements for DOT stone and aggregate. The mine ownership changed several times, which resulted in distinct mine designs in Level 1. Based upon the production requirements and an attempt to maximize limestone recovery from a single level, a variety of pillar dimensions and three mining heights (28 feet, 68 feet and 83 feet) were developed. This was sufficient prior to reaching the mineable extent of Level 1. Level 2 introduced previously unknown ground control challenges. These included: ??Pillar spalling and a significant back fall on the Level 1 - Level 2 decline; ??Laminated immediate back and the need to bolt the back on Level 2; ??Delamination of the back adjacent to the Level 1 - Level 2 decline resulting in bolt shearing, and floor heave in isolated areas of Level 2; ??Multiple level interaction, the need to design pillars based upon numerical modeling as columnization between Levels is infeasible: and ??Water inflow as the mine approached river. To meet the challenges, a testing program to determine rock strength and physical properties was implemented along with numerical (LAMODEL and FEM) modeling, and borescope inspections of the immediate back. The efforts to implement rock mechanics were re-focused as Level 2 approached its mineable limit and the initial attempt to drive a decline to Level 3 was unsuccessful. A second decline site was selected based on inter burden stability, a consistent shale parting for the Level 3 back horizon, results from numerical models of the immediate back and multiple level interactions, and the projected low water inflow. The mine is operating on Levels 2 and 3 with long-term planning and ground monitoring for Level 3.

Jan 1, 2014

By Andy L. Shaffer

A novel liquid settlement system (LSS) was installed in advance of mining at a western United States (U.S.) longwall mine to measure total roof sag from the time of cutting to days after mining during gate road development. The system was used to compare differences in roof sag between conventional place-change mining using a Joy continuous miner and a Fletcher roof bolter and mining using a miner-bolter. The LSS was installed with an intrinsically safe, miniature data acquisition system (MIDAS) to record roof response at four locations in the same gate road. The system utilized pressure transducers to measure roof sag by the principle of falling head (fluid pressure) in fluid-filletubes installed in the immediate roof. Details of the LSS design, installation, data collection, post-processing, and future applications are discussed.

Jan 1, 2014

By Zhang Hongzhen

The fast convergence of boundary is a major problem of probability integral method, especially for the prediction of mining under thick alluvium, abandoned mine goaf, etc. To solve this problem and improve the accuracy of probability integral method, a modified model is constructed for surface movement and deformation based on theoretical analysis. In which, three weighted values i.e. 1, -1/t1, 1/t2 are set for the mining movement and deformation of three different major influence radius i.e. r1, R1, R2, respectively, then the parameters are selected as following: (1) Parameters are inversed based on the observation data, in which the subsidence factor q, deviation of inflection point s, displacement factor b are considered as generic parameters, the tangent of major influence angle tanß is modified as tanß2, that is the major influence radius r is modified as r2. (2) Inversion parameters of tangent of major influenceangle tanß or major influence radius r, based on the observation station edge data which beyond major influenc eradius distance from work-face mining boundary. The inversed tanß and r will be used as tangent of major influence angle tanß1 and major influence radius r1, respectively. (3) Other relevant parameters i.e. t1, t2, R1, R2, are calculated with the algorithm of this paper. A comparison experiment between the traditional and modified models has been conducted using the observation data from a observation station, the results show that in its central area, 58.6 percent of observation points accuracy is improved and 36.6 percent is decreased, while in its edge area, 61.5 percent is improved and 15.4 percent is decreased, totally, 68.6 percent is improved and 30 percent is decreased. Therefore, we can draw the conclusion that our modified model can improve the prediction predication accuracy, in particular, the boundary region.

Jan 1, 2014

By Jessica M. Wempen

Differential Interferometric Synthetic Aperture Radar (DInSAR), a satellite-based remote sensing technique, has been demonstrated as a potentially practical method for measuring mining induced surface subsidence. Unlike traditional methods of subsidence monitoring, DInSAR has the capacity to generate subsidence data on a regional mining scale with a relatively high data density. Using DInSAR to evaluate subsidence over large regions with relatively long time scales has the potential to help quantify the impact of subsidence in the mining region, and provide a means for validating whole-mine geotechnical models. In this study, nine pairs of interferometric data from the Japanese Advance Land Observing Satellite (ALOS) were processed using DInSAR to generate displacement maps for a group of trona mines in southwest Wyoming. The data cover a time span from December 2007 to March 2011. The maximum subsidence for one of the mines totaled 1.3 meters for this period. Cumulative DInSAR displacement maps show the development of subsidence over time. In this mining region, surface subsidence is generated primarily by extraction of trona using retreating longwalls. Additionally, trona is extracted by solution mining, which also generates measurable surface subsidence.

Jan 1, 2014

By Pinnaduwa H. S. W. Kulatilake

A new formulation is given to conduct a probabilistic block theory analysis. A new computer code (BTAC) has been developed to perform both deterministic and probabilistic block theory analyses. The variability of the discontinuity orientation and shear strength is incorporated in the probabilistic block theory analysis. Discontinuity orientation is treated as a bivariate random variable including the correlation that exists between the dip angle and dip direction. BTAC code was applied to perform both deterministic and probabilistic block theory analyses for a part of an open pit mine in the U.S. Needed geological and geotechnical data for the analyses were obtained from field and laboratory investigations. The variability of the discontinuity orientations resulted in important differences between the probabilistic and deterministic block theory analyses results. The results confirmed that the design value selected for the Maximum Safe Slope Angle (MSSA) for a particular region in the open pit mine based on the deterministic block theory analysis can be on the unsafe side. In summary, the results showed clearly the superiority of probabilistic block theory analysis over the deterministic block theory analysis in obtaining additional important information with respect to designing rock slopes.

Jan 1, 2014

By Christopher Mark

Colombia is 11th largest coal producing nation in the world, and the world?s fifth largest coal exporter. But while most of Colombia?s coal is mined at large modern surface mines located near the Caribbean coast, there are also underground mines that produce high-grade metallurgical coal. These mines employ traditional hand-loading techniques in a variety of geologic environments, and they have some of the highest accident rates of any Colombian industry. The National Institute for Occupational Safety and Health (NIOSH) has been collaborating with POSITIVA, the primary provider of worker?s compensation insurance to the Colombian underground coal industry, to reduce the economic and social cost of rock falls in these mines. The specific goals of the collaboration are to 1) document practices and conditions in Colombian underground coal mines, 2) identify relevant international best practices, and 3) provide recommendations for developing a national campaign to reduce fatalities and injuries associated with roof falls. NIOSH conducted a survey of seven underground coal mines in four separate coalfields. Five of the mines were characterized by steep dips and weak roof and floor rock. The coal was loaded by hand at all seven mines, though two employed partially mechanized longwall techniques. Wood posts were by far the most common ground support. Roof bolts were not observed in use at any of the mines, and they are unlikely to replace timbers any time soon. While long-term entries generally appeared to be adequately supported, the survey found that less attention was paid to the temporary support that is installed right after the coal is removed. This temporary support is critical for protecting the workers from rock falls, however, because with hand-loading mining methods most of the activity takes place between the permanent supports and face. The study concluded that improving the temporary support in the working faces would be the most effective way to reduce the number of rock fall injuries. The key principle should be that every worker is protected by planned roof support at all times. Ground Support Management Plans, consisting of specific rules about when, where, and what roof support is to be installed, should be the focus of the campaign. Each Plan should be tailored to a specific mine based on the geologic conditions and mining methods in use. The Plan provides miners with clear, simple rules that can be easily understood, while management can easily check to see if it is being followed. Ground Support Management Plans will also provide the campaign with a concrete focus for the necessary cultural change.

Jan 1, 2014

By Andre Zingano

The coal seam strength and the failure criteria that represent the behavior of the coal seam are very important for mine section and pillar design. Additionally, mine section and pillar design take into account roof and floor layers, which form the roof-pillar-floor system. Therefore, underground ground control design begins, most importantly, with rock mass characterization. Another issue is the distribution or behavior of the coal seam strength for the whole mine area. Sometimes, the coal seam strength is assumed to be the same for an entire area, but this is not true because the coal seam is heterogenic and anisotropic, and also the coal strength is affected by faults and spacing between fractures. The objective of this paper is to demonstrate the use of the methodology for geomechanics characterization to determine the strength for the Bonito coal seam, and discuss the coal seam strength distribution around the entire mine area. The intact coal strength was determined by laboratory tests that were completed during the last 17 years, including triaxial and uniaxial strength tests. It was noted that there is a strong correlation between all laboratory strength tests with 90% confidence interval. The explanation for this coal seam strength variation is the presence of the discontinuities and their variation in quantity and quality at each location in the mine area, because the coal seam rock classification and its behavior will be affected by the quantity and quality of fractures.

Jan 1, 2014

By William J. Schloemer

INTRODUCTION The history of coal mining the Ostrava Region of the Czech Republic goes back nearly 250 years. Both coking coal for steelmaking and thermal coal for the production of energy are mined here; however, it was the coking capabilities that subsequently turned the region into a major steel-producing area in the early 1800?s, something that continues to this day. Ostrava lies in the northeast corner of the Czech Republic, near the southern border of Poland, and falls within the Upper Silesian Coal Basin. The region contains over 400 seams of coal of which about 150 have been mined over its history and continue to be mined. Eighty percent of the Upper Silesian coalfieldlies in Poland and is presently mined by about 35 coal mines; the remaining 20% falls in the Czech Republic, which presently has four mines operated by OKD, a.s., a subsidiary of Amsterdam-based New World Resources. Traditionally, all the mines in this region have employed the longwall method of mining, of which subsidence is an unavoidable consequence. In fact, due to the long history of longwall mining here, there are areas where the overall subsidence has exceeded 37 meters (121 feet). The region is fairly densely populated with residences and industry, and a considerable amount of coal lies under some of these areas where subsidence is not allowed or has to be minimized. It is this reason that has driven OKD to consider alternate methods of mining that will not create subsidence. The decision was made to consider the room and pillar method of mining in order to leave stable pillars of coal to support the surface. After considering several locations, OKD chose the shaft safety pillar at the CSM mine as a test mining location. To say the least, this is a very challenging location in which to conduct a test. As with the entire region, there are many faults from tectonic activity, the seams are pitching at 12 to 20 degrees, the area is affected by high horizontal stress, and the depth of 750 to 900 meters is perhaps the deepest room and pillar coal mining ever attempted.

Jan 1, 2014

By Pieter-Jan Kleiterp

Caterpillar has been involved in highwall mining since the purchase of Bucyrus in 2011. The Cat® HW300 is a continuation of the Superior Highwall Miner that was first sold in the USA in 1994. Currently, there are more than 80 machines supplied worldwide, and Caterpillar envisions increasing the population steadily in the coming years. The Cat highwall miner product group, based in Beckley, WV, has been involved in the sales of all miners to date. With the dealer model that Caterpillar is using, more people, dealers in particular, need to be trained on the application of highwall mining. A site investigation is a highwall specialist?s work, and Caterpillar assists dealers and customers in determining the technical feasibility of highwall mining on mine sites. With the ever-increasing amount of requests, it proved to be important that people without highwall mining expertise, yet who are familiar with mining, could perform a very quick analysis of a potential highwall mining site to determine at an early stage if it is worthwhile to invest the time and money of all parties?customer, dealer, and Caterpillar?in further follow-up. Therefore, Caterpillar would like to introduce the Cat HW300 QuickScan tool.

Jan 1, 2014

By Stanislaw Prusek

In this paper, results of underground measurements conducted in gateroad 3, seam 615, at the Bobrek-Centrum Colliery are presented. The Bobrek-Centrum Colliery is owned by Kompania Weglowa, the largest hard coal producer in the European Union. Yearly production at the colliery, including the longwall system, is about 2 million tonnes. Gateroad 3 was used simultaneously for two retreating longwall faces, No. 1 and No. 2. This working was also employed for the conveyor belt for longwall No. 1 and served as a transport road for longwall No. 2. Approximately 100 meters of gateroad 3 was maintained behind the face of longwall No.1 and then, with the progress of longwall No. 2, it was liquidated. In this paper, we present the results of underground measurements of vertical and horizontal convergence in gateroad 3. We also present the results of numerical modeling for deformation of the working. Finally, we analyse the accuracy of the numerical calculations by comparing them to the actual deformation of gateroad 3.

Jan 1, 2014

By Michael Murphy

A multi-stage triaxial procedure has been developed for the enhanced servo controls and feedback systems at the National Institute for Occupational Safety and Health (NIOSH) rock mechanics laboratory. Due to the difficulty of preparing multiple rock specimens for single-stage triaxial tests at different confinements, multi-stage testing provides a huge advantage if only a few samples of coal measure rocks can be prepared from the drill core. A multi-stage test can provide mechanical properties, post-failure properties, and a complete failure envelope for a single specimen. For the multi-stage test procedure, a parameter used to define the slope of the stress-radial strain curve was developed and monitored in real time in order to successfully predict peak strengths at different confining stages. For this paper, multi-stage tests have been conducted on sandstones of varying strengths, including Berea sandstone which has well-documented properties, and fine-grained and coarse sandstone from a western US coal mine. For the tests conducted on the fine-grained sandstone, it was found that the ramp rate was an important factor in the success of obtaining peak strengths during the multi-stage tests. For each rock type, a table including Young?s modulus, Poisson?s ratio, unconfined compressive strength, friction angle, cohesion, residual friction angle, and residual cohesion are reported. The values from these tables have been used as input parameters for projects at NIOSH requiring numerical model input parameters.

Jan 1, 2014

By Gamal Rashed

Coal bump is a sudden manifestation of the release of strain energy stored in a coal pillar (Peng, 2008). It is a very serious mining hazard that adversely affects the safety and productivity of the mines. Several case histories in mining have described coal pillars or faces of coal failing violently with an accompanying ejection of debris and broken material into the working areas of the mine (Campoli, 1987; Osterwald, 1962; Peperakis, 1958; Garvey and Ozbay, 2013). These failures resulted in large losses of life and total collapses of entire mine panels (Chase, Zipf, and Mark, 1994; Zingano, Koppe, and Costa, 2004). There are questions in the literature about whether or not the coal itself plays a significant role in bump. Rice (1935) mentioned that structurally strong coal is one of the key factors for bump; however, the strength of the Pocahontas #3 coal seam is low, and it bumped. Moreover, it is not obvious in the literature whether the strength of the tested coal samples is the inherent strength or if it is influenced by the shape or the size of the specimen. The main objective of this paper is to answer the following question: To what extent does the mechanical properties of the coal have an impact on the potential for violent failure? The best approach to answer this question is to compare the mechanical properties of two kinds of coals from bump-prone (Utah coal-Sunnyside seam) and non-bump-prone (WV coal-Sewickley seam). This comparison includes uniaxial compressive strength, modulus of elasticity, shear strength (cohesion and friction angle), and the burst index.

Jan 1, 2014

By Sean C. Farrell

In underground mining and tunneling, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Australian companies WDS Limited and Cram Fluid Power, the engineering department of J.H. Fletcher & Company was tasked to design and manufacture roof bolting modules to be mounted off both sides of a roadheader, providing in-cycle bolting. The objective was to produce a boom and bolt module that would allow an operator to bolt from a remote location, eliminating the need for miner to work in unsupported ground. The bolt module needed to operate in front of the cutting boom, but retract to a parked position out of the way during the cutting cycle. Due to Australian electrical approval requirements, it was desirable to design the module with minimal use of electrical controls. The need for multiple, complex, drill steel and bolt handling steps led to the need for a custom hydraulics package to automate several of the movements. The result of the design is dual drill and bolt modules mounted to a multistage boom with over 24 feet (7.31 m) of extension. Each unit rotates and tilts to meet the bolt pattern requirements in conjunction with the stow and load requirements. The bolt module builds on previous designs incorporating a modular assembly with each sub-component designed to be replaceable and adjustable independently from other machine components. Each major component is painted a different color to help the operator make the connection visually from the module to the operator?s control valves. Hydraulic package valves were designed to automatically control several of the sub-components during the drill cycle, reducing the number of steps a drill operator would, otherwise, have to do manually. This design removes the operator from working in unsupported roof and away from other inherent hazards, putting them at a safe distance on the operator?s platform. The cutting and bolting equipment has been combined into one machine, which is advantageous in single entry drifts because there is no need to place change equipment. The hydraulic package valves eliminate the need for any electronics, thus avoiding any electrical regulations with respect to the controls. The addition of these modules to the roadheading machine increases miner safety and streamlines production while meeting the ground control support requirements.

Jan 1, 2014

By Amirhossein Molavi Tabrizi

In this paper we introduce a realistic model for mine openings that explicitly considers the effects of local irregular topography. Also, we consider the effect of entry orientation and rock anisotropy on the induced stress fields around mine openings under the given in-situ stress field. A triangular mesh formulation is derived for representing complicated irregular surface topography and underground openings. Each element contains three internal collocation nodes. Parts of the surface which are far from the mine openings are discretized by infinite elements. The rectangular infinite elements with three internal nodes are introduced specifically for this problem so they are compatible with the triangular elements. With the corresponding boundary element method (BEM) formulation, we then investigate the combined effect of the topography and entry orientation on the stress fields induced by openings in anisotropic rocks under in-situ stresses. A single rectangular opening in the anisotropic ground with topography and in-situ stresses is simulated using data from the Carroll Hollow mine in Ohio. The results of these simulations show that topography, rock anisotropy, orientation of the regional stress field and mine opening geometry all have appreciable effects on the stress fields around underground openings, yet these factors can all be accounted for in an efficient code with no need to discretize the model domain. Future applications using this new BEM formulation will provide useful guidance on selecting the optimal opening orientation in the mine in order to minimize undesirable stress concentrations around underground mine workings.

Jan 1, 2014

By Lorraine Kent

Excessive floor and side deformation are major problems in deep coal mine entries in Europe, and in particular in the UK where rockbolt support is used at depths of working of around 3000 ft. This has major economic and safety implications for the industry resulting in the potential for sidewall instability, disruption to mine infrastructure, (belt conveyors, floor mounted transport systems and powered supports), and the requirement to safely manage excavation of large quantities of floor material. European research aimed at improving deformation control is described. The outcomes include innovations in support systems, materials and installation practices, as well as better methods for predicting and monitoring deformation levels. As coal mines get deeper, some entry deformation is inevitable, and methods for mechanised removal of floor lift and repair of sidewalls have been developed to allow production to continue as mining clearances are re-established.

Jan 1, 2014

By Dakota Faulkner

Unexpected roof falls often occur in the entries or intersections of active mining sections in underground mines. For large roof falls (greater than 20 ft in height), it becomes dangerous and impractical to clean up the rock debris and re-bolt the newly exposed roof strata. To help mine operators rehabilitate the roof fall areas in a quick, safe, and economic manner, Jennmar Corporation and Keystone Mining Services, LLC (KMS) designed, tested, and developed various impact-resistant (IR) steel set designs, as initially detailed in the proceedings of the 30th International Conference on Ground Control in Mining (ICGCM). Since then, the IR steel sets have been successfully installed in more than 100 roof falls in 43 different coal mines. Significant data has been obtained from these installations, enabling further refinement to and improvement on the design. This paper (1) updates drop test results of the IR lagging panel, (2) presents a case study of the performance of IR arch sets installed 56 months ago at a roof fall rehabilitation site, (3) demonstrates capacity evaluation of the IR steel set, and (4) outlines a preliminary applicability evaluation guideline of the IR steel set for a given roof fall condition. Field evaluation and structural numerical analysis indicate that impact capacity of the system is significantly higher than that of the IR lagging panel, as originally determined. It is concluded that, when evaluating the applicability of an IR steel set, ground control engineers should consider the IR lagging and steel set as an entire system and make a reasonable engineering decision based on actual roof fall geotechnical conditions.

Jan 1, 2014

By Zach G. Agioutantis

The Illinois Basin has an extensive history with the use of mechanized longwall mining dating back to the early 1970?s. In recent times, technological advances have resulted in increased panel widths from 800 feet to over 1400 feet and daily panel advance rates have also increased significant l. The prediction and control of subsidence and surface deformation due to underground mining are important considerations in the permitting, planning, and monitoring of these coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology, well utilized in the Illinois basin, and widely used by researchers and planning engineers around the world. This paper utilizes subsidence data, recently measured in longwall operations in Illinois, to develop an updated ground movement prediction capability implemented by the Surface Deformation Prediction System (SDPS) software package.

Jan 1, 2014