Search Documents

By T. Khonthu

The purpose of this investigation was to evaluate the relationship between different milling procedures, viz. a ball mill and an IsaMill respectively, and the flotation performance of the different mill products. Two ores were used, viz. a base metal sulphide (BMS) and a platinum group mineral (PGM) UG2 ore. Flotation was used as a diagnostic to investigate whether the different milling procedures may have different effects of the floatability of the particles. The present study is part of a research programme investigating this question using a wide range of comminutiondevices and procedures. Similar particle size fractions from the different milling procedures were used in the flotation tests. The particles were characterized in terms of particle size distribution, morphology (using scanning electron microscopy and image analysis software) and rheology tests. The results have shown that in general when comparing similar feeds to flotation in terms of equivalent particle size distributions as indicated by the d80 value, the ball mill generally yielded better recoveries and grades in the case of the BMS and lower chromite recoveries in the case of the UG2 ore compared to the IsaMill. No significant differences were observed in the morphological or rheological characteristics of the particles subjected to the different milling procedures. Although the results appear to indicate that IsaMilling is less advantageous than ball milling in terms of the flotation performance for the two ores studied it should be emphasized that these results do not take into account the relative advantage which IsaMilling has over ball milling in terms of direct and indirect energy consumption and GHG emissions nor, most importantly, does it consider the platinum group element recoveries in the case of the UG2 which may have increased significantly as a result of the finer grind which the IsaMill produces after 4 passes compared to the ball mill after 64 min. Such results which will be reported is due course may show that the greater liberation expected after IsaMilling of the PGMs outweighs any disadvantages indicated in this study.

Sep 1, 2012

By Harvey P. Knudsen

This paper describes the results of a comparative study of the geostatistical ore reserve estimation method over three conventional methods; the polygon method, the inverse of the distance squared (IDS) method, and ELIP which is similar to IDS. Each method was evaluated on its ability to accurately predict individual block grades for one bench of the Pima Nine, located near Tucson, Arizona. Results at the Pima Mine indicate that the geostatistical method is no better nor worse in predicting block grades and total tonnage than the ELIP or IDS methods in contrast, the polygon method is clearly inferior. All of the methods would have given better results if geology had been included in the block model. At already producing mines ELlP or IDS may be good choices since they involve substantially less cost in computer time. For prospective or new properties, the geostatistical model is more attractive, due to its ability to construct confidence limits on the estimates.

Jan 1, 1976

By B. Samanta

This paper investigates the performance of the neural network technique in a placer deposit situated at the Nome district in Alaska. Initially a single neural network model was constructed to estimate the gold grade. However, at a later stage, an ensemble model consisting of multiple networks was also constructed via the Adaboost algorithm. The reason behind the use of the ensemble model of the Adaboost algorithm was to examine if the ensemble model provided superior performance to the single neural network. As indicated by other studies, Adaboost did not have a better performance than a single neural network in this specific application. This may be due to the high noise inherent in the gold data used in this project. Consequently R2 values of gold prediction are also poor for both the single and multiple networks.

Jan 1, 2005

By J. M. Tourre

Recently, interest in rare earth based oxide powders for electronic applications has risen dramatically. Considerable research has been devoted to the chemical synthesis of these compounds to improve the control of physical and chemical characteristics of the powder. In most cases, a high degree of homogeneity, purity and reproducibility is necessary in order to obtain good application properties. The synthesis parameters can control particle size, surface area, and morphology as well as the degree of homogeneity and application properties. Rhone-Poulenc, a world leader in the production of separated Rare Earth chemicals has developed a flexible process to produce a wide variety of compounds. The different processes for the synthesis of YBa 2Cu 3 O 7 will be discussed and compared to the RP process in term of product quality, cost and flexibility.

Jan 1, 1992

By M. F. Lopez, A. J. Mattus, S. B. Magid, D. B. Mobbs

"The use of Caro's acid as a replacement for hydrogen peroxide for the oxidation of vanadium prior to solvent extraction resulted in a 56% reduction in oxidant usage when compared on an equivalent hydrogen peroxide basis. Comparative oxidation tests, using two actual uranium mill raffinates, resulted in premature precipitation of an amorphous ferric vanadate when hydrogen peroxide was used to oxidize one of the raffinates containing a high iron to vanadium ratio. The use of Caro's acid eliminated the precipitation problem, thereby permitting the adjustment of the raffinate pH to a higher, more favourable level prior to solvent extraction.Potentiometric characterization of the raffinates revealed that vanadium is responsible for the inefficiency of hydrogen peroxide compared with Caro's acid, with the oxidation efficiency of iron being the same for both oxidants. A limiting potential between 720 and 740 mV was observed when using hydrogen peroxide, while, when using Care's acid, potentials approaching 1200 mV were achievable.A four-stage, countercurrent extraction performed on the oxidized raffinates did not reveal any operational problems. The extraction efficiency and the extraction coefficient were found to be higher when Caro's acid was used as the oxidant, as opposed to hydrogen peroxide.IntroductionMost vanadium is recovered as a by-product of some other process: leaching of Carnotite uranium ores, oil fly ash, phosphate rock or chromite processing. The major source of vanadium has been from uranium mills incorporating acid leaching of Carnotite ore s at elevated temperatures and pressures. The by-product recovery of vanadium from uranium ores of the Uravan Mineral Belt, located in the Colorado Plateau , is a common occurrence when vanadium recovery is economically viable."

Jan 1, 1983

By H. S. Sichel, Kleingeld

A frequency distribution model plays a fundamental role in ore evaluation, especially for the feasibility study of new deep gold mines. The geological complexity of the reefs being mined at present in the Witwatersrand basin poses some difficulties regarding the modeling of the underlying ore-value distribution. This geological complexity has given rise to a need for more applicable distributional models. This paper places the geology of the Witwatersrand basin in perspective and draws some important conclusions from the genesis of the deposition. In addition to the three-parameter lognormal model, two more-general distributional models are proposed. These are the compound lognormal (CLD) and log-generalized inverse Gaussian (LN-GIG) distributions. A detailed, although preliminary, comparative study of these two more-general models with the three-parameter lognormal model is described, and the efficiencies of the estimates and modeling are analysed. It is found that the broad assumption that gold grades follow a three-parameter lognormal law is not always the case, and the need to test for departures from log normality should be emphasized so as to ensure the use of appropriate models.

Jan 1, 1992

By R. K. Devala

In this paper, numerical approximation schemes, for solution of the mass transfer problem in mine ventilation have been developed by using three implicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments, using the concept of Root Mean Square error. For implicit finite difference schemes, in general, the modified central difference scheme is better than the two other schemes at lower velocity. Also, at lower air velocities, implicit schemes underpredicted the concentration values. At higher air velocities, the Crank-Nicholson and Laasonen schemes provided better results than the Modified Central Difference scheme.

Jan 1, 1994

By H. Sevim

Three transportation systems in surface coal mines: 1-Truck Haulage, 2-Belt Conveying, and 3-Coarse-Coal Slurry Transportation are compared from the operations and cost point of Views. Computerized design and cost models were developed and cost data banks were compiled for each system. These models can be used to evaluate transportation systems and layouts that are practiced in most of the U.S. surface coal mines. A typical midwestern area strip mine was considered for illustration purposes. Sensitivity analysis on critical parameters such as production rate, transportation, distance, etc. was conducted and the outcomes are presented.

Jan 1, 1990

By L. Cortez, Á. Magalhães, F. Durão

Methods based on regionalized variables theory, commonly known as geostatistics, have been widely used since more than three decades to predict/estimate spatial distributed data, namely mineral resources, with quite good results. However, some restrictive theoretical assumptions, such as the need of some kind of stationarity of data and the linearity of the predictor/estimator, are often wrong options in many applications. An alternative approach based on a finite mixture modelling, or cluster weighted modelling (CWM) technique, is presented and compared, in its theoretical and practical aspects, with the geostatistical methodology. CWM is a general non-linear framework based on the estimation of joint density functions allowing the calculation of the conditional probability function of the target values given their locations. Validation tests are performed in a 2D case study, where testing data proceeds from a soil contaminated by a heavy metal. The results of ordinary kriging and CWM estimations show a very good agreement with actual data. Keywords: Non-linear regression, Geostatistics, Ordinary kriging, Finite mixture modelling, Cluster weighted modelling.

Jan 1, 2003

By A. R. Laplante

"In this paper, the performance of the Knelson Concentrator and of the batch and continuous Falcon Concentrators are compared. The units are based on different operating principles, and as such they perform quite differently. The Knelson yields very high free gold recoveries over a wide size range of both the recovered and rejected species. It is ineffective in recovering very fine ( <15 µm) or flaky gold, as encountered in flotation feeds, concentrates or tails. It is the: preferred unit for gold recovery from grinding circuits. The batch Falcon is effective in the fine range, typically less than 37 µm for gold. Its recovery zone is quickly saturated when there is significant heavies in the feed. It works best as a pre-concentration unit. The continuous Falcon is a versatile unit which is capable of recovering fine heavies (density down to 5 g/cm3 ), especially from coarser gangue. INTRODUCTIONThe purpose of this presentation is to describe the mode of operation of two Canadian centrifugal concentrators, the Knelson and Falcon. It is hoped that it will prove informative to prospective users in the selection, testing and optimization for applications of either machine. The work is based on testwork both in Canadian mills and at McGill. I am indebted to many colleagues at these locations. Appropriate references will be made to articles further describing the work, either already in the open literature or in preparation.Although this work is meant to be more practical than scholarly, it is appropriate to begin by considering how the two units achieve selective recovery. This will become useful in establishing a suitable testing methodology, which will then be described, and interpreting typical results. In the last section I will attempt to define appropriate applications for the two units. This is a thankless task, as I am likely to miss some applications or to make projections based on partial results, as much of the work is still in progress. In deference to the reader and both manufacturers, areas where reasonable doubt still remains will be identified."

Jan 1, 1993

By A. R. Laplante

In this paper, the performance of the Knelson Concentrator and of the batch and continuous Falcon Concentrators are compared. The units are based on different operating principles, and perform quite differently. The Knelson yields very high free gold recoveries over a wide size range of both the recovered and rejected species. It is less effective in recovering very fine (<15 μm) or very flaky gold, as encountered in flotation feeds, concentrates or tails. It is the preferred unit for gold recovery from grinding circuits. The batch Falcon is effective in the fine range, typically less than 37 μm for gold. Its recovery zone is quickly saturated when there is significant heavies in the feed. It works best as a pre-concentration unit, or when sulphide content is low. The continuous Falcon is a versatile unit which is capable of recovering fine heavies (density down to 5 g/cm 3), especially from coarser gangue.

Jan 1, 1993

By N Maistry, A Singh

It is estimated that in less than a decade, high-grade iron ore reserves in South Africa will be depleted, leaving only low-grade ores with a dominant lithology of banded iron formation (BIF) hematite. BIF is a complex ore reserve as it is typically liberated below 1 mm, resulting in high energy costs. However, due to its abundance, its beneficiation potential should be evaluated to maximise recovery at an acceptable product grade. To develop a beneficiation program for BIF hematite, the first step is to determine the effect of two laboratory crushing techniques on mineralogical characteristics, specifically liberation and shape. For this study, the cone crusher and high pressure grinding rolls (HPGR) were used. The Electron MicroProbe Analysis (EMPA) and Mineral Liberation Analyser (MLA) were used to compare the mineralogical characteristics. The liberation characteristics for hematite are similar for both crushing techniques; however, HPGR preferentially liberates quartz. HPGR achieved 8– 12 per cent additional quartz liberation in the greater than 80 per cent and 100 per cent liberation classes respectively and specifically in +75 μm size range. Improved quartz liberation is associated with lower energy requirements for downstream milling and improved separation efficiencies for beneficiation units that operate in this size range. Both samples displayed similar shape characteristics; most particles were elongated smooth and the rest were elongated angular. Good hematite liberation is expected at grinds of 212 μm to 150 μm. Further consideration should be given to throughputs, energy efficiency and downstream equipment selection prior to selecting a crushing technique.

Sep 18, 2023

By F. Calizaya

This study summarizes the results of various numerical and laboratory experiments per-formed to study the effect of airflow recirculation on gas concentration. The numerical exercises were carried out on a simulated mine ventilation net-work. The laboratory experiments were conducted at the Mackay School of Mines&apos; airflow monitoring system in Reno, Nevada. In both cases, the airflow was recirculated through the system by means of a main fan and a set of booster fans. The booster fans were positioned to produce two types of recirculation: In line and Cross-cut. For each type, various recirculation conditions were generated by changing the booster fan pressure. During each test, the gas emission rate at the simulated working face was kept constant. The study illustrates the conditions under which controlled airflow recirculation may be used to solve a district ventilation problem.

Jan 1, 1991

By E. V. Lilford

Valuators of mineral properties are faced with a range of valuation methodologies, the most important of which are grouped under the headings of the market approach, the cost approach and the income approach. The way in which value is defined and the detail of the different valuation methodologies is examined here. This paper aims at documenting the variety of valuation procedures and applying each method to a variety of gold projects and comparing the outcomes. Any decision to apply a valuation technique will depend principally on the stage to which the project has been developed. The valuation approach to a greenfield project will be substantially different from that applied to a well-drilled, extensively explored mineral property. Furthermore, a valuation exercise may produce different outcomes for the same gold project depending on which method is applied. In order to investigate the variability in valuation methods and to explore the outcomes of different approaches, a series of five gold projects was analysed. The projects differ in regard to levels of capital application, infrastructural setting, depth below surface, in situ grade, and the stage of development, and were valued using the different methods. The most critical aspect of any valuation is the capacity of the valuer to identify the salient issues and ensure that they are incorporated into the valuation. The danger of simply applying ?black box? solutions to valuation problems without a full understanding of the parameters and the areas of uncertainty is emphasized. The importance of the valuator?s experience, insights into best practice and the ability to recognize and submit to the requirements of compliance within the minerals industry is among the most important characteristics of a valuer.

Jan 1, 2005

By Jinung Do, Sung-Ryul Kim, Juhyung Lee

"Model tests have been performed to investigate the vertical, horizontal and cone tip resistances of bucket pile embedded in sand by different installation methods; suction force by pump and jacking force by actuator. Micro-cone penetrometer is used to evaluate the variation of the effective stress inside and outside of the pile after installation. As a result of vertical pull-out test, the jacked pile shows 3 times larger resistance than the suction-installed pile. For horizontal pull-out test, the ultimate horizontal capacity and the slope of load-displacement curve on the suction-installed pile decreases by 22% and 40%, respectively, compared to the jacked pile. In cone penetration test, inside cone tip resistance of the suction-installed pile is about 40% smaller than the jacked pile, which indicates that the effective stress is reduced due to upward seepage of bucket pile in sand by suction force. Therefore, installation methods can affect the behavior of the bucket pile significantly.INTRODUCTIONA suction force occurred when bucket pile penetrates into sandy soils induces seepage flow into the bucket pile so downward seepage near the outside of bucket pile causes to increases the effective stress, while upward seepage inside the bucket pile decreases the effective stress (Mahn, 2005; Fig. 1). The effect of induced seepage causes to reduce the penetration resistance during installation. On the other hand, reduced effective stress can decrease the horizontal and vertical capacities of bucket pile by significant disturbance at the tip of the bucket pile due to the flow net. Due to the complexity and difficulty considering the effects of suction installation, many previous researchers generally have neglected the effect of suction installation in their experiments. Therefore in this study, the effects of suction installation on resistance of bucket pile is examined."

Jan 1, 2016

By B Hu, B Zhang, J Wang, H Ma, D Liu, L Han

Zeolites are potential carriers of slow release fertilisers due to their unique phenomenon for salt occlusion. A comparative study was performed on the capacities of potassium nitrate (KNO3) occlusion in molten KNO3 treated synthetic 4A and 13X zeolite molecular sieves with main channel sizes of 0.41&nbsp;x 0.41 nm and 0.74 x 0.74 nm respectively. The results show that in a laboratory setting, the treated zeolite 4A contained 13.57 per cent of occluded KNO3 and the treated zeolite 13X did not contain any. This was confirmed by the regular release of K+ and NO3- during washing both treated mixed samples with water and by their IR spectra and TG analysis. There are also changes of the relative intensities of peaks in X-ray diffractograms of both treated zeolite samples. K+ release from molten-KNO3 treated zeolites in deionised water and simulated soil solution shows that release of K+ from KNO3 occluded in zeolite 4A are slow and steady. Proper size fit between the channel size of zeolites pore and the size of K+-NO3- ion pair of KNO3 is the decisive factor for zeolites to occlude KNO3.

Jan 1, 2008

By R. K. Rath

The low-grade iron ore sample contains both lumps and fines. It is mostly hematitic iron ore and considerable amount of goethitic/limonitic material is present in it. The major impurities present were quartz and clay. It is observed that the iron bearing phases are poorly liberated above 300 µm and the liberation improves below 300 µm. More than 80% liberation is achieved below 106 µm. Based on the liberation data, the feed for the different beneficiation methods was prepared by stage crushed the ROM followed by grinding passing to 106µm and the ground material (-106µm) was deslimed. The underflow was subjected to various beneficiation techniques such as tabling, enhanced gravity separator (EGS), wet high intensity magnetic separation (WHIMS), and flotation and the results are discussed. All the methods studied could able to produce pellet grade concentrate with iron content of 64.5%, however, a marginal higher yield was observed for WHIMS (81%). Keywords: beneficiation, gravity, magnetic, enhanced gravity separation, flotation, low-grade iron ore, desliming

Sep 1, 2012

By C. W. Lee

"Introduction of diesel engines in underground mines may generate severe health hazards associated with exhaust contaminants. One of the most important parameter in determining the optimal air quantity for hazard reduction is the exhaust dispersion. Through analyzing the exact solution of the diffusion equation and its approximation by finite difference method(FDM) , this paper aims at doing a fundamental research to find an efficient dispersion model suitable to the domestic mines. Diffusion coefficients are likely to be small in the underground airways with high ventilation resistance. This makes concentration profiles similar to the convection-based step functions. It is the case for fixed as well as moving engines. Concentration estimation by exact solution is almost impossible in the case of either a single engine moving at a variable speed or the existence of multiple engines. Application of FDM to the diffusion equation including turbulent dispersion results in the various problems; unstable concentration profiles depending on the engine location, nuctuating concentrations near the engine, and overestimation of the dispersion region of which error grows with waning diffusion coefficient.Convection-based dispersion model is found to fit well for dynamic simulation of exhaust dispersion from multiple diesel engines in the airways showing low diffusion coefficients. Its suitability is more likely in the regions with frequent equipment passage. Published"

Nov 1, 1995

By F. C. Blickensderfer

DURING 1914 and 1915 extensive experiments were conducted at the concentrator of The Detroit Copper Mining Co. of Arizona, at Morenci, Ariz., in order to test the relative grinding efficiencies of the Marathon, the Chilean and the Hardinge Mills. The Marathon mill used in the experiments was the first one ever built by the manufacturers; and since this was the first time that it was given a thorough tryout, with such remarkable results, the data have been, assembled in the following paper and submitted in the interests of the milling profession.

Jan 8, 1916

By F. C. Blickensderfer

THE CHAIRMAN (B. B. GOTTSBERGER, Miami, Ariz.).-On your trip today through the Inspiration and Miami mills you have seen in actual operation the machines which represent the changes adopted in grinding methods in the Miami district from the beginning of operations in March, 1911. In one section of the Miami plant are three Chilean mills not yet discarded, representing the first machines adopted. In another section, pebble grinding is still in operation, while in the balance of the plant, pebbles have been replaced with iron balls. In all cases these machines are handling a feed which is the product of roll, grinding down to about ¼ in. in, size. The latest step in grinding in the district, You saw at the Inspiration plant, where in Marcy mills a filed, the larger pieces of which remain on a 2-in. opening, is being reduced in one operation to a product of which only about 3 per. cent. remains on the 48-mesh screen. A detailed comparison of the methods used at the two plants would be very instructive but our own work at Miami has not yet reached a point where such a comparison is possible, the reason being that our final product is not yet fine enough. By means of larger Hardinge mills operating in closed circuit with Dorr classifiers soon to, be installed in one section of the plant, we hope to obtain, under properly balanced operating conditions the same end result as at Inspiration. It, might interest you, however, to know some of the results we have obtained here by the substitution of balls for pebbles. With pebble grinding, using three 8-ft. by 22-in. mills, followed by one 8-ft. by 66-in. mill for regrinding the coarse product of the primary mills, we handled 636 tons per 24 hr. in one section of the plant. Substituting balls for pebbles in the first operation and using two mills in place of three we obtained a tonnage of .714 tons to the section. With the use of balls both in the primary mills and in the regrinding mills, the tonnage for one section was raised to 822 tons per day. Coincident with this increase in tonnage, we also obtained a greater efficiency. The use of pebbles in all mills showed 21.5 per cent. plus 48-mesh material in the final tailing, which figure was reduced to 13.9 per cent. for balls followed by pebbles, and to 4.6 per cent. with the use of balls both in the primary and regrinding mills.

Jan 12, 1916