Search Documents

By S Sineva, E Jak, M Shevchenko, D Shishin

This study represents a part of comprehensive research aimed at integrating nickel into a thermodynamic database constantly developed at Pyrosearch. The behaviour of Ni in calcium-ferrite slags is considered. An integrated approach combining experimental and thermodynamic modelling methods has been employed to predict phase equilibria in the NiO-CaO-FeO-Fe2O3 system under oxidising conditions and in equilibrium with the metal FeNi phase. The compositions of liquid slags and coexisting solid solutions have been determined through the analysis of equilibrated and quenched samples by electron probe microanalysis technique (EPMA). The research results are presented in the form of liquidus projections on the corresponding phase diagrams, considering both oxidising and reducing conditions. The solubility of Ni in spinel, dicalcium ferrite and calcium oxide as well as solubility of Fe and Ca in Ni monoxide, have been examined under several atmospheric conditions. Additionally, the compositions of the NiO-FeO monoxide in equilibrium with metal phase have been studied. The experimental data not only support the outcomes of thermodynamic modelling but also validate the parameters of the applied thermodynamic models, thus confirming the reliability and accuracy of the integrated approach.

Aug 21, 2024

By H Zhang, Y Wang, S Sukenaga, H W. Ni, H Shibata, W Z. Mu

The crystallisation behaviour of low melting point CaO-SiO2-Al2O3-MgO inclusions greatly affect the deformability of inclusions during the rolling process. The crystallisation characteristics of CaO-SiO2- Al2O3-MgO melts representing the oxide inclusions in Si-Mn killed steel were systematically investigated. The effect of Al2O3 and MgO contents on the crystallisation change were analysed under a fixed CaO/SiO2 in the complex inclusions. The continuous-cooling-transformation (CCT) and time-temperature-transformation (TTT) experiments were conducted. The results showed that the increase of MgO content increases the crystallisation ability of CaO-SiO2-Al2O3-MgO inclusions, while the increase of Al2O3 content has the opposite effect. The viscosity, liquidus temperature of oxide melt and also the initial crystallisation potential might be the reasons for the change in crystallisation behaviour. Also, the crystallisation activation energy could semi-quantitatively characterise the crystal growth during the crystallisation of inclusions. To obtain low melting point plasticized CaO-SiO2-Al2O3-MgO (CaO/SiO2=1) system inclusions, the Al2O3 content of the system needs to be controlled larger than 15 wt per cent and the MgO content should be kept at a small amount.

Aug 21, 2024

By A Specht, A Müller, V Montenegro, S Winkler, E Klaffenbach, A Schmidt

In the process of primary copper smelting in flash smelting furnace (FSF), the ratio of iron to silica (Fe/SiO2 mass ratio) primarily determines the slag viscosity and magnetite formation. Viscous slag does not only cause difficulties in daily operation, such as in tapping, it also increases the copper losses to slag. Thus, keeping the Fe/SiO2 mass ratio at the desired level is an important aspect of FSF and slag cleaning furnace (SCF) operation. In this study, the improvement of the Fe/SiO2 mass ratio was conducted in two steps: First, the optimal Fe/SiO2 mass ratio was derived based on thermodynamic data. Based on this analysis, appropriate control limits were determined. Second, this range of favourable Fe/SiO2 mass ratios was implemented into operation by an advice-based control system, which suggests the addition of silica based on the analysis of SCF slag. As this approach was successful, the same advice-based control system principle was adapted for the coke addition to the SCF. After testing the new advice-based control for several months, the production data confirm the predictions by thermodynamics: since the prediction was implemented as an advisor, the copper and magnetite content in SCF slag is significantly reduced and viscous slag is reported less often by operations.

Aug 21, 2024

By A D. Pradana, D R. Pradana, Y H. Putra, Z Zulhan, T Hidayat

The high temperature processing of nickel laterite ore is currently dominated by the Rotary Kiln- Electric Furnace (RKEF) technology. The ratio of SiO2/MgO (S/M) in the ore is one of the critical parameters that determines the success of the RKEF process. Incompatible S/M ratios in the ore can cause aggressive chemical interaction between the slag and MgO refractory. The slag-refractory interaction at conditions relevant to nickel laterite ore smelting was investigated in the present study. Synthetic mixtures representing the slag compositions of nickel laterite ore smelting were prepared by mixing MgO, SiO2, Al2O3, CaO, Fe2O3, and Fe and heating the mixtures in steel containers at 1300°C under an argon atmosphere for 3 hrs. Pure MgO crucible were used as containment material in the melting process of the mixtures to represent the MgO refractory. The kinetics of the slagrefractory reaction were investigated using samples with selected initial S/M ratios of 2.0 and 3.0 (wt/wt) (with constant CaO = 3 wt per cent, Al2O3 = 5 wt per cent, FeO = 10 wt per cent) by performing melting at 1500°C in MgO crucibles for 5, 30, and 120 mins under an argon atmosphere. The effect of the S/M ratio in slag on the slag-refractory interaction was also investigated by performing melting of mixtures with different initial S/M ratios of 1.75, 2.0, 2.5, and 3.0 (wt/wt) in MgO crucibles at 1500°C for 120 mins under an argon atmosphere. After the melting process, each sample was quenched in water, mounted in resin, ground, polished, and coated. The interaction between the slags and MgO refractory was then evaluated by analysing the polished samples using a scanning electron microscope equipped with an energy dispersive spectroscopy (SEM-EDS). Thermodynamic simulations using FactSage™ 8.0 thermochemical software were performed based on the experimental slag compositions, refractory, and conditions to support the evaluation process. The results show that a higher S/M ratio in slag leads to a higher tendency for the refractory component to dissolve into the slag. A higher S/M ratio in slag also leads to an increasing extent of solid-state diffusion of iron oxide into the remaining refractory grains. The dissolution of MgO into the slag is rapid; the MgO concentration in the final slag increased by 2.4 wt per cent and 5.7 wt per cent at initial S/M ratios of 2.0 and 3.0 wt/wt, respectively, within 5 and 30 mins of the melting process.

Aug 21, 2024

By Q Zhuo, P C. Pistorius, M N. Al-Harbi

A likely increasingly important pathway for future low-carbon ironmaking and steelmaking is the combination of gas-based direct reduction with electric furnace steelmaking (DRI-EAF route), or with electric smelting (DRI-ESF route). In the DRI-EAF route, the gangue that is present in the iron ore is fluxed and removed as slag in the melting (steelmaking) step. This is in contrast with integrated steelmaking, in which the gangue is removed as part of blast furnace ironmaking. For DRI-EAF steelmaking, the amount and composition of slag depend on the iron ore composition, flux additions and iron yield. Slag volume and composition affect phosphorus removal, foaming behaviour and the process energy requirements. In this work, heat data from a year of DRI-EAF production was analysed to test whether the expected relationship between slag volume and electricity consumption for EAF steelmaking was observed. The data include slag analyses (one sample per shift), and heatlevel information on all inputs, final steel temperature and dissolved oxygen concentration, electricity consumption, tapped steel mass and tap-to-tap time. In analysing the data, the slag volume was estimated from the assayed slag CaO concentration and CaO inputs to the EAF. The expected effect of slag volume on steelmaking energy consumption was calculated with a mass and energy balance, considering the heat of mixing of the slag. The calculated energy requirement of slag formation is in line with previous estimates reported in the literature.

Aug 21, 2024

By G Cao, Y R. Cui, J X. Zhao, H P. Gui, G H. Wang, Z M. Wang, M M. Ren, B Li

Pyro-metallurgy is still the main process for lead production and a lot of lead direct smelting processes have been developed in recent years. All the processes will experience two steps in common. The first is the oxidisation of PbS to PbO and then reduction from PbO to Pb, furthermore, from ZnO to Zn. So, the composition of melts, especially the slag composition at reduction step change continuously. Up to now, there are few systematic results on the slag physical-chemical properties with its composition change. In this work, the typical lead direct smelting processes were analysed from theoretical and practical standpoints. The full-period slag composition and slag melting point change were compared. Especially, to the PbO and ZnO reduction steps, based on the full-period slag composition change, the slag properties were predicted. Based on dust composition and test results, the mechanism of Pb compound evaporation and its effect on practice and measurement of high PbO bearing slag physical-chemical property is discussed. It is suggested that to restrain the evaporation in practice and to obtain more accurate measurement results of physicochemical properties of smelting slag are the key problem not only to set high efficiency, energy saving process, but also to environmental pollution control.

Aug 21, 2024

By P Taskinen, D Lindberg

The increase in metals demand in the electrifying globe means significant growth in the smelting of copper, nickel, zinc, and lead, produced from primary sulfide sources or using sulfide mattes as the intermediates of the process chains. This means that leaner and complex mineral deposits will be evaluated as ores and are in the future traded in the commodity market for smelting and refining to pure metals. An important issue in the trend is the technology metals, like antimony, tellurium, and gallium, which exist as trace elements in sulfide ores and form no ores of their own. Their recovery becomes important in the coming decades as will be the case with growing slag amounts without use in other industries. The key is to produce environmentally acceptable slags in the smelting operations. It sets new boundary conditions to the treatment of flue dusts. This means that all material streams of smelting and refining must be re-evaluated for the deportments of the main and minority metals. In copper smelting, the recoveries of precious metals are today important for the feasibility of the custom smelters but due to low prices of many minority metals they are discarded in slag landfills. It is one of the emerging issues also in the secondary copper smelting today and once the demand grows, the same question will be faced also in the mining-beneficiation-smelting-refining chain of the primary production of nickel, zinc, and lead. The distributions of many technology metals in the copper and nickel smelting have been recently studied using methods where the chemically bound trace elements in the slag and its phases at the smelting conditions have been studied. Thus, the key data about options for process modifications and additional processing steps are piling up. Short processing routes in the metals smelting and refining are attractive due to their simplicity. At the same time, complexity of many raw materials challenges the fluxing at high oxygen partial pressures in low silica slags with high metal concentrations. The compromise between high primary recovery and safe operation is a demanding task in conditions where slag foaming outside the processing window is evident. The increase in the demand of pure nickel is challenging the raw material basis where low-grade sulfide ores are soon smelted along with nickel laterites to matte. It is a demanding task at high MgO concentrations. The low solubility of MgO in iron silicate slags requires new fluxing strategies and new smelting end points for the operation at reasonable temperatures; the direct nickel matte smelting in one-matte mode may be an option.

Aug 21, 2024

By Y-B Kang, J H. Park, J Park

In order to understand the effect of oxygen injection into the molten metal on the valuable metals (VM) recovery and interfacial phenomena, several high-temperature experiments were conducted using a high-frequency induction furnace with a quartz tube as the reaction chamber at 1673 K. Copper-based waste printed circuit board (PCB) that contains some impurities was selected as the end-of-life resource. CaO-SiO2 based pre-fused slag and oxygen gas were used in present works. The composition change and microstructure of the samples were analysed. As oxygen was injected into the system, impurities were rapidly removed. After the removal of impurities, continuously injected oxygen lowered interfacial tension between liquid slag and liquid metal. Lowered interfacial tension induced Cu loss into the slag.

Aug 21, 2024

By M G. Shaw, M A. Rhamdhani, S P. Singh, A R. Duffy, B Eisenbart, A K. Shukla, G A. Brooks

The field of astrometallurgy is a growing area of study. Metal production on the Moon is likely to begin in less than a decade as major space agencies such as NASA (National Aeronautics and Space Administration) and CNSA (China National Space Administration) are preparing to construct permanent lunar bases. The utilisation of regolith to generate oxygen and metals is expected to be important in the development of a sustainable lunar habitat. This paper provides an overview of potential metallurgical processing methods for lunar conditions, emphasising the impact of lunar factors on slag chemistry. The interaction between regolith and the extracted metals, as well as their impact on slag composition and refractory performance, are critical considerations in metal production on the lunar surface. The initial research on lunar metallurgical technologies is focused on oxygen extraction and Fe-Si alloys are reported as the by-products of these processes. This paper delves into the fundamental thermodynamics associated with the carbothermic reduction of lunar regolith. Thermodynamic analysis using the FactSage™ ver 8.2 software package indicates that the Fe-Si alloy can be produced as a metallic product from the lunar regolith at temperatures ranging from 1400°C to 1600°C under terrestrial conditions. However, under ultra-high vacuum conditions (3 × 10-15 bar) on the Moon, the required operating temperature for producing ferrosilicon would be significantly reduced. Thermodynamic modelling results indicate that under lunar vacuum conditions, Fe-Si alloys only exist as solid phases at lower temperatures below 650°C. At higher temperatures, both Fe and Si are expected to be present in the gas phase. In this work, the carbothermic reduction of the Lunar Mare Simulant (LMS-1) is conducted under terrestrial conditions. The findings indicate that the process can readily yield Fe-Si alloys with 7–10 wt per cent Si at 1600°C. Additionally, energy dispersive spectroscopy (EDS) analysis of the resulting Fe-Si alloy indicates the presence of phosphorus up to 1 wt per cent.

Aug 21, 2024

By M Zhu, G Tranell, J You, K Tang, X Ma

The thermal conductivity of slag is critical for the efficiency of high temperature metallurgical processes such as the smelting reduction of ferroalloys, the ladle refining and the continuous casting mold flux in steelmaking. Experimental determination of slag’s thermal conductivity is fraught with challenges, as seen in yielding data for the SiO2-Al2O3-CaO system that are often inconsistent and widely dispersed. In molten slags of this system, thermal transport occurs via phonons within the network structure. To quantitatively describe thermal conductivity based on the microstructure, hightemperature Raman spectroscopy was employed to measure the silicate tetrahedra Qi (i = 0, 1, 2, 3), with Q4 species inferred from mass balance. This study also integrated molecular dynamics simulations to provide a fundamental understanding of the microstructure units distributions. Machine learning algorithms, especially deep neural networks, were applied to establish the relationship between slag composition and the configuration of tetrahedra. The thermal conductivities were then connected with silicate tetrahedra Qi using an Arrhenius-type formalism. This study sets the stage for extending our findings to more complex, multicomponent slags, enhancing their practical application in industrial processes.

Aug 21, 2024

By V Rimal, d M. Tangstad

Multiphase slags form the basis of the reduction pathway for manganese ferroalloy production. The present work aims to understand the flow of slag through the coke bed based on experimentation in controlled conditions. Synthetic slags of different basicities were evaluated for their phase composition, viscosity, and flow. The two-phase slag will have two zones: a liquid slag zone and a multiphase zone. The multiphase zone will consist mostly of a solid phase with some liquid slag between the solid particles. The multiphase part will hence have a high viscosity. The liquid zone will flow into the coke bed while the multiphase area will stay. With increasing reduction, the multiphase area will decrease in size until the solid phase is gone and the whole slag will flow into the coke bed. The effective viscosity of slag will decrease with the lowering of the solid oxide phase. The results from flow experiments confirmed that the segregation of phases occurs when slag flows through the coke bed. It is observed that the flow is dependent both on the size of the void and the viscosity of slag.

Aug 21, 2024

By T Kon, K Ohno

Slag foaming is an important control item in the process of refining molten steel. This study aims to investigate the factors controlling slag foaming by observing the bubble formation behaviour resulting from the chemical reaction between iron oxide and Fe-C alloy in the slag. In this study, 0.06 g of Fe- C alloy was introduced at the bottom of a BN crucible, and 6.0 g of slag (SiO2:CaO:Fe2O3 = 40:40:30) was placed on top of it. The crucible was positioned inside an infrared image heating furnace, where the temperature was rapidly raised to 1370°C at a rate of 1000°C/min in a nitrogen stream, and then held at that temperature for a predetermined time before rapid cooling. Following rapid cooling, the internal structure of the sample was examined using a high-resolution X-ray CT device. The spherical equivalent volume was calculated based on the number of observed bubbles and their equivalent circle diameter. Additionally, the relationship between the volume ratio of small bubbles in the slag volume and the distance from the bottom of the crucible was determined, along with the calculation of bubble density and volume ratio. Under various experimental conditions, numerous bubbles with equivalent circular diameters ranging from 200 to 300 μm were consistently observed. The density and volume fraction of bubbles with circular equivalent diameters between 200 and 500 μm showed a tendency to increase as the distance from the bottom of the crucible increased. Bubbles with equivalent circular diameters of 500 μm or more consistently exhibited lower bubble densities, regardless of their height within the crucible. The formation of larger bubbles is attributed to a decrease in iron oxide concentration within the slag as the reaction progresses. However, this is believed to be due to their higher buoyancy, resulting in shorter residence times within the slag and a reduction in the number of encapsulated bubbles.

Aug 21, 2024

By Y B. Kang, Y J. Park

Ti-added ultra-low carbon (ULC) steel is produced by adding Al and Ti during the secondary refining process to deoxidise molten steel and to bind C and N which are detrimental to the deep drawing quality of the steel product. However, the production of Ti-added ULC steel faces challenges, including submerged entry nozzle clogging and surface defects on cold rolled coils. The troubles were often attributed to ‘Al-Ti complex inclusions’ in the molten steel. However, the evolution of oxide inclusions including their stability has been still unclear. In the present study, the evolution of these inclusions in Ti-added ULC steel was investigated by phase diagram measurement, CALPHAD thermodynamic modelling, high-temperature stability test for the oxides, and observation of transient behaviour of oxide inclusions in the steel. The phase diagram of the Al-Ti-O system was elucidated with an emphasis on oxygen potential, which significantly controls the stability of the oxides. CALPHAD thermodynamic models and a self-consistent database were developed. The transient behaviour of Al-Ti complex inclusions in Ti-added ULC steel was observed in situ using a confocal scanning laser microscope. This was additionally validated by the new thermodynamic model. The equilibrium phases of the oxide inclusions were investigated using a high-temperature resistance furnace, and were analysed using a secondary electron microscope, energy dispersive spectrometer, and electron back-scattered diffraction. By considering the morphology and crystal structure of these inclusions, the evolution of Al-Ti oxide inclusions was elucidated. Various behaviour of Al-Ti inclusions and their influence on steel cleanliness are discussed.

Aug 21, 2024

By S Zummar, A Van den Bulck, T De Staercke, T Van Rompaey

An increase of 22 per cent in lead usage is expected in the European Union by 2050. During lead refining, the Harris process is a critical step in which a salt melt is used to remove arsenic, tin and antimony. During this process, the caustic salt melt absorbs these impurities, requiring regular evacuation before saturation. Current metallurgical practices for: 1) determining the end point of the lead alloy involve time-consuming sampling and offline analysis, and 2) determining the end point of the caustic salt melt are based on subjective visual observations by the operator. In the context of Industry 4.0 concept, automating these processes becomes desirable, as smart sensors systematically collect real-time data in an unbiased manner. This research focuses on monitoring the Harris refining process using objective methodologies. Two different methodologies are investigated. The first methodology focuses on electrical conductivity changes of the caustic salt melt as function of Sb content. For this study, synthetic and industrial samples are used. A lab-scale electrical conductivity set-up was built to accommodate the aggressiveness of the salt melt. Initial findings suggest a promising relationship between electrical conductivity and Sb content in the caustic salt melt. Although the results are preliminary, the study provides valuable insights by enabling real-time measurements. The second methodology focuses on measuring the electromotive force (EMF) in lead doped with Sb at pilot-scale. Multiple probes are reevaluated for their effectiveness in Sb measurement. Ultimately, a partially stabilised MgO probe with Ni as a reference, without cardboard and copper protection caps, yields promising results. A correlation between EMF and Sb content is observed. However, repeatability issues arise due to possible wire interference at low temperatures. The results underscore the potential of advanced measurement techniques in optimising lead alloy production within the context of Industry 4.0.

Aug 21, 2024

By N Voller, A Ishmurzin, G Hackl, M Wu, A Kharicha, M Chintinne, C M. G Rodrigues, A Ludwig

Slag fuming (SF) is a critical process for recycling zinc-containing slags, but the corrosive nature of molten slag poses challenges to the reactor durability. The freeze-lining (FL) technique offers a solution by forming a protective layer on the reactor wall. It requires intensive cooling using watercooled jackets, which can stabilise the FL while compromising the energy efficiency of the process. This study presents a computational fluid dynamic (CFD)-based model to optimise the SF process by considering FL formation and its impact on heat transfer and reactor wall temperature. A volumeof- fluid (VOF) model is coupled with a mixture continuum (MC) solidification model to capture the intricate multiphase flow dynamics within the SF furnace. Two FL types are considered: FL solidifying on the reactor wall in the slag bath region; and FL solidifying on the reactor wall in the freeboard region. The FL of the first type forms when the slag temperature drops below liquidus temperature. The FL of the second type only forms when a splash-induced slag droplet collides with the freeboard wall and solidifies. A series of splashing events are necessary to coat the freeboard wall. The simulation was run until a global energy balance was reached. This means that the heat losses from the water-cooled jacket, bottom wall, outlet and fuming balance the heat gains from the hot gas injected through the submerged plasma torches. The increase in FL thickness, due to its low thermal conductivity, reduces the heat losses through the reactor walls. The calculated FL thickness and heat fluxes were in good agreement with industrial data, validating the model’s credibility. The simulation results provided valuable insights into the fuming process, including slag bath temperature evolution, slag splashing dynamics, FL formation patterns, local heat fluxes through the reactor wall and overall energy balance. These findings can inform process optimisation strategies to enhance the energy efficiency and sustainability of SF operations. The authors have built a prior version of the model framework and applied it to simulate FL formation in an electric smelting furnace (ESF). The results from both the ESF and the current SF highlight the applicability of such model framework to a range of industrial processes involving FL formation. This model framework can ultimately contribute to more energy-efficient and sustainable industrial operations.

Aug 21, 2024

By M I. Pownceby, M A. Rhamdhani, S Palanisamy, D Fellicia, B Satritama, G A. Brooks, A Ang

Metal production have long been using carbon sources as both reducing agents and energy sources. Consequently, the global extractive metal sector contributes significantly to greenhouse gas emissions, accounting for approximately 9.5 per cent. Hydrogen gas offers as a promising ecofriendly alternative to carbon in metallurgical processes, serving as both a reductant and energy supplier with a by-product being only water vapour. However, the implementation of molecular hydrogen faces certain challenges related to the thermodynamics and kinetics of metal oxide reduction. In addressing these challenges, researchers have explored the application of hydrogen plasma, generated by subjecting molecular hydrogen to high energy to produce atomic, ionic and excited hydrogen species. Hydrogen plasma offers thermodynamic and kinetic advantages over molecular hydrogen and carbon-based reductants, exhibiting lower standard Gibbs free energy of reaction and activation energy. Therefore, hydrogen plasma can produce metal in fewer steps, process any oxide feed and feed size and even be used to refine metals. Despite these advantages, challenges exist in utilising hydrogen plasma in extractive metallurgy, including electricity costs, potential reverse reactions and industrial-scale implementation. This study provides a mini review of prior research on hydrogen plasma for metal oxides reduction, particularly iron oxide, as well as state-of-the-art techniques for its use in extractive metallurgy applications by mentioning several reactor types. Future prospects and scale-up possibilities of the hydrogen plasma in extractive metallurgy will also be presented.

Aug 21, 2024

By M K. Nahian, R G. Reddy

The thermodynamic model for species distribution in aluminium chloride (AlCl3) and 1-butyl-3- methylimidazolium chloride (BMIC) system was developed. The experimental thermodynamic data, considering a range of aluminium chloride species, such as AlCl4-, Al2Cl7-, Al3Cl10-, Al4Cl13-, and Al2Cl6 were used in developing the model. When the XAlCl3 was in the range of 0 to 0.50, only anion species Cl- and AlCl4- were existing in the solution. As the XAlCl3 value increased more than 0.50, the available anions were Al2Cl7-, Al3Cl10-, Al4Cl13-, and Al2Cl6. Specifically, the concentration of Al2Cl7- increased in the composition range from 0.50 to 0.67 XAlCl3, after which it decreased. This change in the concentration of Al2Cl7- was due to its reaction with excess AlCl3, leading to the formation of Al3Cl10-. The average cathode current density was determined by the electrochemical experiments varying XAlCl3 from 0.50 to 0.71 in the AlCl3:BMIC solutions. The average cathode current density increased as the XAlCl3 increased from 0.50 to 0.67. However, it decreased when the XAlCl3 > 0.67. This trend can be attributed to the electroactive species Al2Cl7-. The Al2Cl7- promotes the reduction rate at the cathode, resulting in an increase in the average cathode current density.

Aug 21, 2024

By Y Zhang, Z Zhao

The green production of the steelmaking process has urgent requirements for fluorine-free fluxes. In this article, a new solid waste-based slagging flux was applied in the external dephosphorisation test of low silicon hot metal to replace the traditional fluorite-lime dephosphorisation slag. The results showed that under laboratory conditions, the new flux was utilised for smelting low-silicon molten iron with a phosphorus content of 0.10~0.13 wt per cent, the temperature of the molten iron was 1350°C and the slag amount was controlled at 2 per cent. Within ten minutes of smelting, the dephosphorisation rate of the molten iron reached more than 50 per cent. When making slag with new flux, the slag melting time was about 40 seconds and the P2O5 content in the final slag was higher than 8 wt per cent. In the industrial test of a 150 t molten iron ladle, under the same molten iron conditions, an out-of-furnace dephosphorisation test was conducted in the Kambara Reactor (KR) process. The flux material consumption per ton of steel was 8~10 kg. Within 15 minutes of smelting, the dephosphorisation rate of the molten iron was about 30 per cent. During flux slag making, the slag melting time was about three minutes and the P2O5 content in the final slag was higher than 6 wt per cent. This new solid waste-based flux has significant cost advantages and outof- furnace dephosphorisation effects and is expected to become the benchmark for a new generation of fluorine-free steelmaking fluxes.

Aug 21, 2024

By Y Mita, T Iwama, R Inoue, S Ueda

In the iron and steel manufacturing industries, efforts are being made to achieve carbon neutrality by 2050, and the transition from a coal-based steelmaking process to that utilising renewable energy is being pursued. An alternative process in which directly hydrogen-reduced iron is melted in an electric furnace is being investigated. It is known that foaming slag reduces heat loss from the steel bath in electric arc furnace, but iron loss due to the suspension of steel particles in the slag is indispensable. To improve the separation of steel particles from the slag, the control of the slag viscosity is important. Although the slag viscosity has been extensively studied, in those studies the slag was considered to be a simple liquid. However, in actual operations, slag is a multiphase fluid consisting of solid, gas and liquid phases. Therefore, in this study, by measuring the sedimentation velocity of titanium, stainless steel and glass spheres in an aqueous glycerin solution containing bubbles generated by the reaction between NaHCO3 and C2H2O4, the apparent viscosity of the gas-liquid fluid was evaluated based on Stoke’s law. It was found that the apparent viscosity of the gas-liquid fluid is larger than the viscosity of liquid phase and depends on both the bubble volume ratio in solution and the density of the falling solid sphere, and the apparent viscosity was different from that previously obtained by the rotation method. The apparent viscosity derived from the sedimentation velocity of solid spheres changed depending on the specific gravity of the ball. This is because the apparent viscosity is derived from the velocity of a ball falling in a static bubble in this method, whereas that is derived from the force applied by a stationary flow in the rotational method.

Aug 21, 2024

By K L. Avarmaa, M A. Rhamdhani, A D. P Putera, H T. B M Petrus, G A. Brooks

Multistage slag treatment was carried out to investigate boron removal from metallurgical grade silicon. Boron is known to be one of the most difficult elements to remove from silicon. Depending on boron initial concentration, boron can be removed from silicon into certain level; most previous studies have attained final 50–100 ppmw (parts per million weight) boron in the silicon using slag treatment. The term ‘multistage’ refers to a process where the resulting silicon from the initial slag treatment is further refined multiple times using a new slag. In this study, an initial slag composition of 45CaO-45SiO2-10Al2O3 (wt per cent) was utilised. Using this technique, boron level in the silicon was expected to be gradually lowered because the new slag will always have more capacity to reach the equilibrium distribution coefficient (LB = (ppmwB)slag/(ppmwB)Si). The current study was carried out through combined thermodynamic calculations (using FactSage™ ver 8.2, by Thermfact Ltd, thermochemical package) and high-temperature experimentation. The thermodynamic calculations were carried out for reactions at 1500, 1550, and 1600°C for three different scenarios: 1. Single stage refining with varied slag to Si ratio. 2. Multistage refining with slag to Si ratio of 1:1. 3. Multistage refining with slag to Si ratio of 2:1. The multistage experimental work was carried out at 1550°C under inert gas atmosphere each time for 2 hrs, with slag to Si ratio of 2:1. The simulation results indicate that the boron distribution coefficient stay essentially constant with varying slag to Si ratio and temperature, around 1.8 to 2, and the experimental results measured LB in the same range, between 1.5 and 2.5. By harnessing this feature, the simulation showed that boron can be removed by approximately 78 per cent in each stage. The experimental result confirmed that the boron concentration in the silicon was reduced by a total of 97.8 per cent from its initial value using four stages of slag treatment, from initial 270 ppmw down to 6 ppmw.

Aug 21, 2024