Search Documents

By Z. Xingrong, L. Jiongtian, Z. Yangge, C. Yijun, L. Liang, H. Yangjia, H. Long

In this present research, a polymer poly (acrylamide-allyl thiourea) (PAM-ATU) with an average molecular weight 1.66 × 104 g/mol was used as a depressant in the flotation separation of molybdenite from chalcopyrite and galena. The micro-flotation experimental results showed that PAM-ATU exhibited a strong influence on the flotation performances of chalcopyrite and galena, but had little effect on that of molybdenite within a pH range of 9.0~11.0 at a dosage of lower than 6.0 mg/L. The flotation results of bulk flotation tests illustrated that PAM-ATU showed a stronger depression power than sodium thioglycollate (TGA) and sodium sulfide. The comparison results demonstrated that PAM-ATU and TGA had an advantage in reducing galena and chalcopyrite impurities in the molybdenum concentrate, respectively. With the combination of PAM-ATU and TGA, a good flotation separation result was achieved through one roughing operation where the recovery of molybdenum in the froth product was over 75.0%, while the recovery of copper and lead were less than 22.0% and 15.0%, individually. It was also found that a molybdenum concentrate with Mo grade of 46.32%, Cu grade of 0.16%, Pb grade of 0.06%, was obtained by a closed circuit flotation flowsheet of one roughing-three scavenging-five cleaning with a Mo recovery of 77.67%. Keywords: PAM-ATU, molybdenite, depressant, chalcopyrite, galena

Jan 1, 2020

By A. Singh, R. D. Govender

The current method employed to quantify the efficiency of separation of ferromagnetic ores by wet low intensity magnetic drum separators (WLIMS) incorporates the use of a conventional benchscale Davis Tube (DT) operating at a magnetic field intensity that is equivalent to that of the drum’s surface. However, empirical research has indicated that the magnetic force, or force index, rather than the magnetic field intensity, is the critical factor in the operation of the magnetic separator (Murariu and Svoboda, 2002). Furthermore, the current aforementioned practice would yield incorrect information as the magnetic field gradients produced by a typical WLIMS unit differs considerably from that of a bench-scale DT. In light of this, research on magnetite focusing primarily on the scale-up of DT results to pilotscale WLIMS were undertaken. The investigation entailed a comparative study between that of a typical WLIMS circuit and a bench-scale DT. The purpose was to practically evaluate the performance of a WLIMS, bench-marked against the traditional laboratory-scale DT unit. Moreover, the secondary objective was to produce a magnetite concentrate graded at 69% Fe, 95% -45μm, as a suitable source of separation media for use in the Dense Medium Separation (DMS) industry. Fundamental findings of previous works provided a framework for the study, however, a realworld approach was explored. Preliminary testwork conducted at Mintek investigated the performance of a DT and a typical multi-stage laboratory-scale WLIMS circuit (operating at 1000 Gauss at the surface). The results attained indicated that a DT operating at high intensities is comparable to a single rougher WLIMS stage. Additionally, it was observed that the three stage laboratory-scale WLIMS circuit performed similarly to the DT operating at 1000 Gauss. Moreover, piloting testwork was undertaken, carried out in larger 380mm drums, and the results attained showed a strong correlation with laboratory-scale findings. Keywords: Davis Tube, wet low intensity magnetic separation, magnetite

Jan 1, 2020

By Y. Zhang, F. Zhu, Y. Zhao, L. Dong, Y. Li

In order to obtain a more suitable separation medium for fine coal, in this paper a pulsed fluidised bed was used to measure the pressure fluctuation, density characteristics, bubble diameter and rising velocity of Geldart A and B particles in the bed by controlling the pulsation frequency and gas velocity, in order to study the fluidisation effect and two-phase distribution of the bed. The results indicated that with the increase of pulsation frequency, the breakthrough point on the fluidisation characteristic curve caused by particle adhesion disappeared, and there was an optimal frequency, which made the minimum fluidisation velocity of particles reach the minimum. In addition, the bubble rising velocity was also simulated. The relationship between them was established using a model, and the error was within 5%. This provides an effective way to predict the bubble velocity, study the distribution of bubble phase, and improve the stability of bed density. Keywords：Frequency, flow velocity, pressure fluctuation, bed density, bubble

Jan 1, 2020

By Q. Cui, B. Z. Zhou, Z. G. Song, Y. G. Zhu, G. B. Zheng

The complex refractory Cu-Pb-Zn polymetallic ore in Xinjiang, China is a massive sulphide ore with complex mineral components. In the past two years, the ore mineralogy has changed, resulting in a decline in metallurgy, with too much zinc reporting to the lead and copper concentrates. A detailed mineralogical study indicating the presence of secondary copper minerals, which could be activating the sphalerite early in the present circuit, was used to develop a novel reagent and flotation flowsheet termed “Pb-Cu co-flotation, Cu intensified flotation, Zn flotation”. It was tested and found to significantly contribute to improving the flotation performance of the ore. In the Pb-Cu co-flotation circuit, successful depression of pyrite and sphalerite was achieved using a BK612- Na2S based depressant system. Most of the galena and some of the Cu bearing minerals with excellent floatability were collected with the use of the selective collector BK906. The rest of Cu bearing minerals were floated in a copper Z200 circuit using a BK537-lime-zinc sulphate based depressant scheme. Zinc flotation from the copper tailing was performed in a SIBX circuit using lime as a pyrite depressant. Using the proposed flowsheet, overall Pb, Cu, and Zn recovery increased significantly to 88%, 87%, and 90% respectively. Keywords: Complex polymetallic ore, Cu-Pb-Zn, Pb-Cu co-flotation, particle size

Jan 1, 2020

By F. Rosenblum, K. E. Water, J. A. Finch, S. Moon, Y. H. Tan

Previous work has shown that sulphide self-heating occurs in three distinct stages referred to as Stage A, Stage B and Stage C. In this paper the focus is on the transition from Stage A to Stage B, which occurs at ca. 100OC. Background literature hints that the transition corresponds to the transformation of the rhombic form of elemental sulphur to the more reactive monoclinic form that occurs at 96OC. A test apparatus is modified for adiabatic heating to track the transition. The results support this transformation of sulphur as being key to the transition, and the transition temperature is thus modified to 96OC. Variations in a sample’s response under adiabatic conditions are observed and possible reasons are discussed. Testing in adiabatic mode provides new insights into the sulphide self-heating process that complement the test designed to identify propensity to self-heat. Keywords: Self-heating; Stage A/Stage B; transition; rhombic/monoclinic elemental sulphur; adiabatic heating

Jan 1, 2020

By E. G. Galvez, E. Mate, L. A. Cisternas, C. Cruz, L. Cortés, M. E. Osorio

Designing and optimising flotation circuits are critical for mineral beneficiation plants, and therefore several procedures have been published. The modelling of flotation circuits with the objective of design and optimisation is problematic in that different approaches are used for the modelling of flotation units and regrinding units. Usually, regrinding models are based on particles characterised by their size, while flotation models are based on species characterised by fast and slow classes. The relationship between particle size and liberation can be used, but it requires laboratory studies that are time-consuming and costs are high. It is therefore not surprising that few studies on flotation circuit design and optimisation include flotation units and regrinding units simultaneously. In this paper, it is proposed to model the regrinding stage using species characterised by fine-slow, medium-fast, and coarse-slow flotation species. In deep, the regrinding model is derived from a population balance approach based on flotation species. The fraction of these species at the feed and product of the grinding unit is determined by flotation tests. Then, based on these data, the model parameters can be determined by a regression estimation procedure. A local ore was used to validate the model. Keywords: Modelling, flotation circuit, grinding circuit, process design

Jan 1, 2020

By I. Y. Motovilov, S. A. Telkov, M. B. Barmenshinova, Z. S. Abisheva

As a rule, removing waste rock at the beginning of the process improves the conditions for the flotation of minerals, and also reduces the operating costs of crushing, grinding and flotation. Lead-zinc ores in the Shalkiya deposit of the Republic of Kazakhstan are classified as difficult for enrichment, but taking into account their significant reserves, they are one of the main potential ores for the production of lead and zinc. Under industrial conditions, for processing ores of the Shalkiya deposit, a selective flotation concentration scheme with the production of lead and zinc concentrates is recommended. However, according to the recommended scheme, it is not possible to obtain high-quality concentrates of lead and zinc, with high metal recovery. The paper presents the results of studies of preliminary gravitational enrichment of lead-zinc ore in the Shalkiya deposit. Based on the fractional analysis for the particle size range of -40+8 mm, Henri- Reingard enrichment curves were constructed, separation density (2730 kg /m3) was established to isolate the light fraction with the lowest possible lead and zinc content, and gravity enrichment indices (0.7-0.71) were determined. It was found out that when using gravitational enrichment of the original large-sized ore in the Shalkiya deposit, tails are released at the beginning of the technological process with a yield of up to 20% with the extraction of silica up to 30%, calcite up to 11% and carbonaceous matter up to 12%. As a result of the studies, it was found that the beneficiation of crushed lump ore could be conducted in heavy suspensions. One of the positive aspects of the use of gravitational enrichment is the reduction of energy costs for grinding the heavy fraction, which was experimentally proved in this article. Keywords: Lead-zinc ores, Shalkiya deposit, fractional analysis, gravitational enrichment, floating fraction, sunken fraction, separation density

Jan 1, 2020

By I. Silin, H. Wotruba, A. Liono, I. Volobayev, Y. Rubinstein, D. Gürsel

Old, abandoned or in situ processed and storaged tailings can be a potential source of remained valuable metals and minerals. By reprocessing of tailings, it is possible not only to achieve economical profit from recovery of valuable metals, but also to reduce environmental damage caused by tailings such as generation of acid mine drainage from sulfide minerals, mobilization of heavy metals, soils and groundwater contamination. In addition, storage facilities can be successfully redesigned with modern geotechnical requirements and monitoring to avoid a dam collapse of abandoned tailings. In this case study, the processing of low grade abandoned tailings was investigated. Copper (0.15%), cobalt (0.032%) and gold (0.35 ppm) were determined as main valuable and recoverable metals. Cobalt occurs as cobaltite and cobaltiferrous pyrite, while chalcopyrite represents copper. The fine fraction of tailings below 32 μm is enriched with cobalt and copper. Preliminary test-works with initial tailings sample were aimed to recover copper, cobalt and gold. The previously tested magnetic and gravity separation could not recover the metals in a pre-concentration step. Flotation tests of the tailings sample had shown a suitability for flotation without previous regrinding of the tailings. The valuable minerals are first proposed to be recovered by collective flotation, followed by a selective circuit with production of a low grade copper concentrate and a cobalt bearing pyrite concentrate. Based on various tested collectors, amounts of sulfidisation agents and activators, a suitable reagents regime was determined and used for up-scaling by locked cycled test. Keywords: reprocessing, tailings, copper, cobalt, gold, flotation, cobaltite, cobaltiferrous pyrite

Jan 1, 2020

By T. Moodleya, I. Govender

Despite the widespread use of DEM to simulate particle processes, comparatively little work has been done to evaluate its accuracy. One of the reasons is a lack of available measurement techniques that can capture dynamic information at the momentum transfer timescale which is lower than 10-6 s - typical of the kinetics occurring within the drum. This work makes use of Positron Emission Particle Tracking (PEPT), an in-situ method capable of measuring 3D kinematic data at 1000 frames per second. PEPT measurements are performed using 3 mm and 5 mm mono-size glass beads in a 300 mm diameter rotating drum at critical speeds that are relevant to industry. We undertake systematic ‘tuning’ of DEM with a view to optimising the agreement between experiment and simulation. To ensure an equitable comparison scale, both the DEM and PEPT data are coarse grained within representative volume elements. This work seeks to validate DEM predictions against experimentally derived PEPT kinematic measurements. Keywords: PEPT, nuclear imaging, DEM, Tumbling Mills

Jan 1, 2020

By R. V. Peche

Since 1952, Bond’s equation has been used as a standard to predict the specific energy of grinding for a given duty. The Bond’s equation considers that the exponent is constant for all conditions. Hukki, in 1961, pointed out that the exponent is a function of the particle size, and concluded that the Bond’s equation applies successfully for an intermediate range of sizes; out of this range the Bond’s equation leads to high error as demonstrated in this paper. More recently, in 2004, S. Morrell presented a new formula in which the exponents vary with the feed and product size. This paper is based on Hukki’s approach and presents a new general formula, in which the exponent varies only with the feed particle size. This new equation has been proven in 82 observable cases in Peru and other countries around the world, involving ball mills and vertimills in different configurations over a wide range of feed and product sizes, work indices and mill diameters; in most cases, the predicted value has an error less than 10% with regards to the observed value and no need for any correction factor. Keywords: Grinding, specific energy, particle size, work index, variable exponent

Jan 1, 2020

By M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

This paper describes research done to remove apatite (phosphorus) from hematite ultrafine (70% finer than 25 micron) concentrate, recovered by electromagnetic separators at the FST Tailing Recovery Plant located in Chadormalu Iron Ore Complex through reverse froth flotation. As a result, iron and phosphorus content in magnetic concentrate (flotation feed) were 53.52% and 0.58%, respectively. Therefore, to increase the Fe content and decrease the P content of the sample, reverse flotation tests were applied. Chemical reagents used in this research consisted of sodium silicate as a depressant, sodium hydroxide and sodium carbonate as pH regulators, Alke & Dirol as fatty acid collectors and MIBC as frother. Process parameters including dosages of collectors, depressant and frother, preparation times of depressant and collectors, steps and time of frothing and pH range were selected. After doing flotation tests, in optimum condition, dosages of collectors were 1200 g/t, depressant 1200 g/t, pH in the range of 9.5 to 10, preparation time of collectors in the first step was eight minutes and at the other steps, four minutes; the number of frothing steps 4 and frothing time in each stage was three minutes. In this case, it was observed that the amount of phosphorus in the final concentrate was reduced to 0.05%, the Fe content increased from 53.52% to 61.66% and the Fe recovery achieved was 82.21%. Keywords: Iron ore, hematite ultrafine concentrate, iron and phosphorus content

Jan 1, 2020

By C. Steyn, J. D. le Roux

A dynamic model is used to represent the single-stage closed grinding mill circuit at Mogalakwena North Concentrator. The circuit consists of a ball mill closed by a hydrocyclone. The circuit is modelled according to a semi-mechanistic non-linear dynamic model available in literature. An algebraic routine is used to fit model parameters to steady-state process data. Preliminary validation results against dynamic data indicate that the model is capable of capturing the main dynamic trends of the plant. Since classical system identification techniques proved insufficient to produce accurate models; the non-linear model can be used as a reliable source for model-predictive controller design. Keywords: Grinding, modelling, process control, parameter estimation

Jan 1, 2020

By M. Getz, G. Asbjörnsson, M. Evertsson, E. Clausen

The mining and minerals processing industry is gradually being digitalised to improve efficiency and reduce waste. One aspect of this transition is to ensure that relevant process-data in sufficient quality and quantity is given to the operator in the right format and at the right time to improve decision-making. Augmented reality (AR) can serve as a potential ICT-based support tool for human operators to achieve this goal. With AR, virtual information is combined with the real world in real-time. Therefore, AR technology has the potential to fulfil the need for improved data visualisation in Industry 4.0. This article is the result of a collaborative effort of Chalmers University of Technology and RWTH Aachen University to identify selected state-of-the-art applications of AR that are currently being applied in the mining and minerals industry or selected related industries. This paper aims to show opportunities for the application of AR in the mining and mineral processing industry with selected conceptual applications. This paper concludes with several requirements identified as necessary to implement the conceptual applications of AR in the mining and minerals industry. Keywords: Augmented reality, mining, mineral processing

Jan 1, 2020

By J. E. Dickinson, R. Campbell, M. J. Cole, K. P. Galvin, M. C. Cole

It is common practice in the beneficiation of iron ore ultrafines to apply reverse flotation, and hence float the gangue minerals, leaving behind a high-grade iron ore product. Given the difficulty in floating particles finer than 20 μm, especially those finer than 10 μm, it is necessary to subject the feed to desliming ahead of flotation. There are two problems with this approach. Firstly, given the known inefficiencies of cyclones, desliming needs to be aggressively applied to particle sizes upwards of 45 μm to ensure all the offending ultrafine gangue is removed. Secondly, desliming also removes a significant portion of the valuable iron ore. Thus, a significant portion of the ultrafines, including the iron ore, is lost to the tailings. This paper examines the direct flotation of iron ore fines using the Reflux Flotation Cell. The RFC operates using a concentrated bubbly zone, in the absence of a conventional froth zone, for delivering strong counter current washing through an inverted fluidised bed of bubbles ahead of the product discharge. A system of parallel inclined channels in the lower part of the cell provides enhanced segregation of the bubbles from the tailings, preventing the loss of air bubbles into the tailings. Experiments conducted under semi-batch conditions produced encouraging results with concentrates of ~65% Fe grade in a single flotation stage. Comparatively, up to five successive batch flotation stages were required when using a laboratory scale batch mechanical flotation cell to achieve similar Fe grades. For a given grade, lower Fe recoveries were typically achieved by the RFC. This was attributed to the effective prevention of ultrafine particles succumbing to hydraulic entrainment under a positive bias flux, as well as an increasing feed volume involved in the semi-batch operation using inverted fluidisation water for cleaning. Overall, similar grade-recovery curves were produced, however, significantly higher grades were obtained by the RFC and with fewer separation stages. Keywords: Desliming flotation, iron ore, modified release analysis, reflux flotation cell

Jan 1, 2020

By A. Chagnes

This paper presents a modelling tool that can be used to predict the behaviour of solvent extraction processes. In particular, this model allows calculating metal extraction efficiency as a function of pH, solvent flowrate, stripping flowrate and aqueous feed flowrate in the mixers-settlers. This model is applied to the recovery of cobalt from acidic chloride media by using CYANEX® 272 as extractant diluted in kerosene. Keywords: Cobalt, mixer-settler, modelling, solvent extraction

Jan 1, 2020

By T. Bui, T. Wallmach, S. B. Blancher, A. Back, M. Pierre, V. Delarue, A. Kanzari

This study investigates nickel laterite porosity and its impact on geometallurgical modelling. We performed a detailed mineralogical study on a set of Ni-laterite samples originating from New Caledonia. Samples were analysed after heavy liquid separation by automated SEM (QEMSCAN®). Laboratory and QEMSCAN® modelling results do not correlate well. Ideal physical mineral properties such as mineral densities used in QEMSCAN® modelling do not match the actual physical densities of minerals. The presence of empty or water-filled pores can represent important amounts in minerals and change the overall density of a particle. An adequate modelling of real density separation of minerals and particles should consider the water-filled pores. The first step towards a better simulation was to integrate pores larger than 10 μm in diameter filled with water (density of 1 g/cm3) in the QEMSCAN® database. The results approached, but did not match the physical laboratory results. The second step was to identify nanometer to micrometer sized pores, which could not be identified by QEMSCAN®. It was possible to identify nanometric pores in enstatite, Fe-oxides, serpentine, talc and quartz, and radial aggregates of fibrous Fe-oxyhydroxides with high resolution SEM (HR-SEM). The quantification of those micro-sized pores was performed on 2D HR-SEM images using image-processing techniques developed in Python to calculate the nanometer to micrometer scale pores in each mineral. Despite the limitation of converting 2D imaging into 3D objects, in our case pore sizes and porosities, we were able to calculate a mean value of porosity for each mineral. The integration of this porosity in the calculation of particle densities yielded a good match between the QEMSCAN® model and the laboratory experiment results. Despite the complexity of a strongly weathered material, such as Ni-laterites, a good knowledge of the ore makes it possible to build reliable processing models. Keywords: Mineralogy, geometallurgy, nickel laterites, SEM, QEMSCAN®, porosity, density

Jan 1, 2020

By K. -I. Higuchi, M. Mizutani, K. Haga, A. Shibayama, A. Batnasan

In recent years, the quality of iron ores has decreased due to the increase in the content of impurities, namely quartz, aluminum, phosphorus, and sulfur. It indicates that the removal of impurities from iron ore is an extremely challenging task. In particular, the high amount of phosphorus in iron ore could be a problem for energy consumption and CO2 emission in the steelmaking process. To reduce the impact of phosphorus, mainly two approaches: the utilisation of low-phosphorus iron ore, or dephosphorisation of high-phosphorus iron ore using mineral processing technology, have been suggested. In this paper, the removal of phosphorus from a low-grade high-phosphorus iron ore containing 0.1 mass% P and 57.5% Fe by alkaline roasting and wet grinding is discussed. The iron ore consists mainly of hematite, goethite, and quartz. Effects of sodium hydroxide concentration used as an alkaline source, roasting temperature, grinding time, and particle size on the dephosphorisation of highphosphorus iron ore were investigated. The dephosphorisation efficiency, iron loss, and mineralogical components of low-grade high-phosphorus iron ore under various experimental conditions were characterised by using XRD, SEM-EDS, and particle size distribution analysis. Results showed that the phosphorus content was lowered from 0.1 mass% to 0.034 mass%, while the iron grade reached 59.8 mass% from 57.5 mass% by alkaline roasting with 0.05 w/w NaOH at 300 °C for 2 h, followed by wet grinding in an attritor with water for 30 seconds at room temperature. Under the experimental conditions, the dephosphorisation rate was about 54.7%, and the solution obtained by wet grinding contained 22.7 mg/L of phosphorus and 21.5 mg/L of iron. The recovery rate of iron by this process reached 99.9%. Keywords: Iron ore, phosphorus, dephosphoriszation, alkaline roasting, wet grinding

Jan 1, 2020

By C. Bergmann, V. Ross

The concept of underground ore processing, in which valuable ore and waste are separated at a coarse particle size to improve the economics of operations and minimise the environmental impact, seems attractive from a sustainability perspective. Perceived benefits of such an operation include energy and cost savings due to a reduced hoisting load, a reduced footprint of surface operations, and using material for backfill that has not been contaminated by process chemicals. Progress in the South African mining industry in this area has however been below expectation, and opportunities for underground processing in deep, narrow reef operations were therefore explored by an Excel-based simulation with sensor-based sorting (SBS) as concentration technology. Various PGM mining scenarios incorporating factors such as the mining rate, depth of operation, and effects of dilution and particle size on the metallurgical efficiency, were compared. Whilst these initial results can be regarded as indicative only, they have shown that the economics of such an operation are driven by selective mining at significantly higher rates than achievable with conventional methods. Also, the cost of preparing, conveying and placing rock backfill will need to be lower than that of hoisting waste and depositing it on a surface dump. Another aspect to be addressed is whether ore sorting machines would be able to operate under harsh conditions underground and what provision would need to be made to ensure their efficient operation. Further investigations should focus on refining costs, incorporating environmental considerations in the modelling of economics and sustainability, and compare greenfields with brownfield scenarios. Keywords: Ore sorting, hoisting, backfill, mining rate, economics simulation

Jan 1, 2020

By J. Ojeda, R. Kuyvenhoven, M. Ziemski M

This paper focusses on the identification of operational opportunities in a 1100 tph pellet plant to reduce the specific energy consumption in its comminution circuit, which is designed to process magnetite ore and produce pellets to be used as raw material in the iron and steel industry. The assessment is carried out through a frequency analysis for three of the four processing lines of the plant, consisting of one ball mill each with an installed power of 4.5 MW and 280 tph of mill throughput design capacity. The methodology, as described in this paper, facilitates the visualisation and quantification of plant performance and provides a good first approach to prioritise alternatives for optimisation. In a pellet plant, grinding is a critical stage due to its high energy consumption and its major impact on the physical properties of the iron pellets, which quality depends to a large extent on grind size and Blaine index. From the evaluation that was performed it can be concluded that production line 2 has the lowest specific energy consumption of 15.1 kWh/t, while line 1 has the highest with an average of 16.6 kWh/t for the same type of ore. On the basis of the results and current operational practices, it is recommended to increase the average mill throughput from 240 tph to 265 tph, translating into specific energy reduction of 10%, without affecting the chemical and physical properties of the final product. The implementation of an HPGR for regrinding the magnetic concentrate is proposed to assure adequate specific surface area in case grinding coarser becomes an alternative, which would also be beneficial for the subsequent water recovery stages. Keywords: Iron ore pelletisation, grinding circuit, energy efficiency, particle size, frequency analysis

Jan 1, 2020

By S. Banisi, M. R. Yarahmadi, S. R. Mortazavi

Nowadays the development of automatic on-line sampling systems has enabled large amounts of data to be available to plant managers. These data are inevitably prone to random and sometimes systematic errors. Data reconciliation methods are used to deal with random errors. In these methods, the measured data are adjusted in accordance to their error, so that the mass conservation law is satisfied at the same time. Measured data may also contain systematic errors, using these data in mass balancing software will result in inaccurate or even irrational results. In this paper three methods for detecting systematic errors (global test, node constraint test and maximum power constraint test) were presented. A step by step method to locate the systematic errors was demonstrated. Then, the new version of Movazen©, a mass balancing software, was introduced and used to locate systematic errors in the measurements taken from the Sarcheshmeh pilot plant copper flotation circuit. Keywords: Mass balancing, data reconciliation, random error, systematic error

Jan 1, 2020