Search Documents

By T. Kalliomäki, A. T. Aji, M. Lundström, J. Aromaa

The settling properties of anode slime in copper electrorefining have crucial effect on copper cathode quality. Anode slime settling is affected by electrolyte composition and temperature, electrolyte circulation, and the sizes and density of the slime particles and agglomerates. Typically, the industrial copper electrolytes contain 40–60 g/dm3 Cu2+, 130–220 g/dm3 H2SO4, 0.04–25 g/dm3 Ni2+, 0.005–30 g/dm3 As, and have operating temperature of 55–70°C. In optimal electrorefining process, the settling rate of anode slime is sufficiently high to avoid the risk of getting the slime entrapped in copper cathodes. In this research the settling properties of copper electrorefining bottom slimes, mainly consisting of Cu, Ni, Ag, Se, Pb, As, Bi, Sb and Ba compounds, were studied by settling rate tests. The tests were conducted in water and synthetic electrolytes with known viscosities and densities. In addition, the effect of agglomeration was taken into account – it was observed that breaking the agglomerates which existed in the as-received slimes decreased the particle sizes on average 56–73%, which decreased the settling rate. The results of this study provide detailed information of anode slime settling and thus clarify the conditions causing cathode contamination risks in copper electrorefining. INTRODUCTION Settling rates of Cu-ER anode slimes affect the purity of cathode copper and faster settling rate decreases the contamination risk (Davenport et al., 2002; Shi & Ye, 2013). The settling rates are affected by the properties of anode slime particles (Wills & Napier-Munn, 2011; Aaltonen, 2014; Kiviluoma, Aaltonen, Aromaa, Lundström & Forsén, 2016) as well as viscosity and density of the electrolyte (Davenport, King, Schlesinger, Biswas, & Robinson, 2002; Shi & Ye, 2013). Thus, it is crucial to find out how the viscosity and density affect the settling rates. Small spherical particles with diameter below approximately 50 µm obey Stokes’ law (Equation 1) (Wills & Napier-Munn, 2011). v = gd 2 (ρS – ρF) (18η) -1 (1) where v is terminal velocity (m/s), g acceleration due to gravity (m/s2), d diameter of particle (m), ρS density of particle (kg/m3), ρF density of fluid (kg/m3), and η dynamic viscosity (Pa∙s). The approximate effects of kinematic viscosity (ν = η / ρS), density (ρS) and particle sizes on settling rates defined for small anode slime particles based on Stokes’ law are presented in Figure 1. However, Stokes’ law does not take into account other than spherical shapes, and it is only applicable for small particles. Consequently, the real settling rates of the particles are lower than these (Wills & Napier-Munn, 2011). Moreover, some of the anode slime particles are larger than 50 µm (Aaltonen, 2014).

Jan 1, 2019

By Zheng Deming, Li Hongwei, Lei Zhan, Dai Chunyang

This paper introduces the application of a digital electronic detonator in the demolition blasting of largescale (LS) and long delay time (LDT) frame-shear structure buildings. The whole building to be demolished by blasting is an L-shaped frame shearing structure. Some parts of these buildings have a large length along the direction of collapse, so the detonation delay of the column is longer. To ensure the building is successfully blasted and demolished, a digital electronic detonator detonation system is adopted. In the design of the detonating network, full use is made of these characteristics of the digital electronic detonator, such as flexible installation, high precision of delay before blast, and dedicated testing equipment to check the reliability of the network. These advantages ensure the damage of the load-bearing structure is within the blasting gap and that the accuracy of the collapse time of the building, which not only guarantees the collapse effect of the building, but also provides strong technical support for improving the intrinsic safety of the blasting operation and the supervision of the flow direction of the detonation, these research be provide reference for the application of digital electronic detonators in similar projects.

Jan 1, 2019

By C. Pawlik, R. T. Jones

Cobalt occurs together with copper in the southern African copper belt, and a large portion of this cobalt ends up in copper smelting slags, mostly dissolved in oxide form. It is possible to achieve high recoveries of cobalt by reductive smelting of the copper slags, using some form of carbon as a reducing agent in an electric furnace. For example, a 40 MW DC arc furnace was operated at Chambishi Metals in Zambia from 2001 to 2008, and demonstrated cobalt recoveries of around 80% from slag to an iron-rich alloy containing copper and cobalt. The alloy was atomized prior to leaching. With the recent increase in demand for cobalt (and the resulting high metal prices), there has been increasing interest in this process route. There is also an alternative hydrometallurgical process for recovering the valuable metals from the slag. The choice between these process options requires a trade-off between capital and operating cost and environmental acceptability. This paper examines the potential for cobalt recovery from slags, and outlines various process options. INTRODUCTION Cobalt has had a number of important uses in society since antiquity, and its principal use has changed dramatically over time. Since at least 2250 BC, cobalt-based pigments (cobalt blue) have been widely used to colour manufactured goods such as glass and pottery. Later, cobalt became known for its magnetic and wear-resistant properties and high-strength alloys, and most of the cobalt produced was consumed in the production of cobalt-based superalloys. The greatest recent growth in cobalt demand is due to it being essential to the rechargeable lithium-ion batteries used in consumer electronic devices and increasingly to drive electric vehicles. Cobalt is usually produced as a by-product of copper or nickel. The copper belt in the Democratic Republic of the Congo (DRC) and Zambia supplies most of the world's cobalt production. In 2018, the DRC was expected to produce 90 000 tons of the world total of 140 000 tons of cobalt (Shedd, 2019). This paper focuses on the southern African copper industry, and specifically the cobalt that is able to be produced as a co-product from this. A BRIEF HISTORY OF SOUTHERN AFRICAN COPPER SMELTING Copper deposits in South Africa have been documented since at least 1685, when the Cape governor, Simon van der Stel, ‘discovered’ the 'Copper Mountain' at Springbok. South Africa's first public commercial mining company (imaginatively called the 'South African Mining Company') was established in Cape Town in 1846, to exploit the rich copper resources that were believed to exist in Namaqualand.

Jan 1, 2019

By Mi, Dong Liang, Jingyuan Bai, Victor Zhou, Xujun

Squirrel cage induction motors are the mostly used motors at present. Currently, the rotors of the squirrel cage induction motors are produced by aluminum die casting technique with the advantages of low cost of rotors. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size. Considering the huge quantity of motors, the die casting process is the best solution to produce copper rotor with economic cost. Because of the characteristics of copper, it is difficult to produce copper rotors by casting similar to that done in aluminum rotors. In order to improve the die casting quality of copper rotor, a new tooling structure was developed and the casting process of copper rotor was simulated and analyzed by Any-casting software. The filling process, solidification process, inner gas distribution and residual melt modulus were analyzed. It was found that the design of symmetrical runner and inner runner on both sides was helpful to reduce the impact of molten copper to the cavity surface during the filling process. The use of Slag traps array can reduce die casting defects inside the end rings. That will be helpful to improve the rotor quality. INTRODUCTION Squirrel-cage AC induction motors are most widely used in the world. In 2017, the total installed capacity of AC motors in China has reached more than 1.2 billion kW, and the annual power consumption accounts for about 60% of the total national electricity consumption. To improve the efficiency of squirrel-cage motor will be helpful to energy conservation and environment protection. There are several ways to improve efficiency of induction motors, using copper rotor is one of the most effective solutions. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size.

Jan 1, 2019

By E. Wraith, W. W. Culver, B. Wesstrom, P. J. Mackey

Electrodeposited copper of the 1860s was of unprecedented purity, although the profound significance of this achievement was not fully realised until the dawn of the electrical age a decade or so later. By the 1870s there were three somewhat large (4 to 4.5 tonnes Cu/day) electrolytic copper refineries in Germany based on J. B. Elkington’s process, first patented in the United Kingdom in 1865. More such refineries were planned throughout Europe. At the same time, copper output in the U.S.A. was starting to expand and with the spread of European electrolytic copper refining technology across the Atlantic, the door opened to major increases in North American output. The technology was first taken up in 1879 by James Douglas at the Chemical Copper Company in Phoenixville, Pennsylvania, where he was Superintendent. Douglas was assisted in this pioneering work by Edward Weston. The copper refinery at the Chemical Copper Company was small, not unlike the first plants in Europe. The present authors contend that the electrolytic copper refinery at the Chemical Copper should be regarded as the first copper refinery in the United States. The Balbach Copper Refinery in New Jersey, which commenced operations in 1883 with an initial production of about 2 tonnes Cu/day, has been erroneously considered as the “first commercial refinery”; it rightly belongs in second place. The early developments at these plants are discussed in this paper. INTRODUCTION In the mid-1800s, the main uses for copper were as sheathing on the wooden sailing ships of the day to protect from marine growth, boiler components in locomotives and steam engines, along with some construction uses. Copper ores were generally smelted, and further fire-refined for market. The recovery of gold and silver, if present in payable amounts, was a slow and relatively expensive step. This situation regarding copper would change by the 1870s with advances in the generation and use of electricity. The introduction of the dynamo led to major developments in electrorefining. First demonstrated in principle by Faraday in 1831 (Faraday, 1832), the dynamo was subsequently adapted and further developed by J.S. Woolrich for electro-metallurgical applications in 1842 (Woolrich, 1842; Napier, 1845). It provided a new source of power with the unprecedented potential to significantly change the scale of metal production by electrometallurgy. Interestingly enough, copper would be needed for the electrical age just beginning. By 1869, advances in dynamo design offered relatively reliable large machines, which enabled J. B. Elkington in the United Kingdom to use the dynamo in the radically new Pembrey copper electrorefinery — the first copper electrorefinery in the world (Wraith, 2013). Initial production at Pembrey was small — in the range of 1 to 2 tonnes/day — while gold and silver were recovered more readily by the treatment of the slimes than with methods used hitherto.

Jan 1, 2019

By Ali Bunjaku, Lauri Pesonen, Hannu Johto

It is well known that there are many ways to process copper concentrates into copper anodes using the pyrometallurgical route. All modern copper smelting technologies are fundamentally energy efficient and environmentally safe options, and therefore choosing one depends on the desired capacity range, feed impurity levels, plant location, flexibility needs, overall energy use, and of course smelter economics in both the short and long term. This paper focuses on comparing different solutions which have potentially the lowest variable opex (operational expense), meaning in practice finding out which technology offers the best chances for profit maximization under certain scenarios. For the comparison, we chose to have a closer look at Outotec Flash Smelting (FSF) – Peirce-Smith Converting (PSC), Outotec Flash Smelting (FSF) – Outotec- Kennecott Flash Converting (FCF), Outotec Ausmelt TSL Smelting (ASF) - Peirce-Smith Converting (PSC), Outotec Ausmelt TSL Smelting (ASF) - Outotec Ausmelt TSL Converting (ACF), Mitsubishi Smelting Process (MIT), Bottom Blowing Reactor (BBR) – Bottom Blowing Continuous Converting (BCC), and Side Blowing Furnace (SBF) - Top Blowing Converting (TBC) since these seem to be the main state-of-art technologies now being applied in many recent copper smelter projects around the world. The work was carried out by modelling each smelting route by using the new HSC SIM 9 simulation software and applying operation time, energy, and consumables consumption numbers for each unit process and stream. Combined with cost data, the exercise produced a rich set of information which will be shown in detail for each area per scenario. The authors’ goal here was to provide a fair comparison where each technology can be evaluated from various perspectives such as electricity use or refractory consumption. INTRODUCTION Copper can be produced either pyrometallurgically or hydrometallurgically. The hydrometallurgical route is used only for a limited amount of the world’s copper production (~20%) and is normally only considered in connection with in-situ leaching of copper ores. On the other hand, most of the copper extraction from Cu-Fe-S minerals is pyrometallurgical (~80%) (Schlesinger 2011, ICSG 2017). Thus, several different processes can be applied for copper production, including the following state-of-the-art technologies: Outotec Flash Smelting (FSF) – Outotec-Kennecott Flash Converting (FCF) Outotec Flash Smelting (FSF) – Peirce-Smith Converting (PSC) Outotec Ausmelt TSL Smelting (ASF) - Peirce-Smith Converting (PSC) Outotec Ausmelt TSL Smelting (ASF) - Outotec Ausmelt TSL Converting (ACF) Mitsubishi Smelting Process (MIT) Bottom Blowing Reactor (BBR) – Bottom Blowing Continuous Converting (BCC) Side Blowing Furnace (SBF) - Top Blowing Converting (TBC)

Jan 1, 2019

By A. Supomo, H. Resendiz, C. Burbidge

"Freeport-McMoRan Inc. (FMI) commissioned the expansion of the Morenci Metcalf concentrator in 2014. The concentrator included many design and equipment innovations, including the first-of-its-kind Metso Hydraulic Roll Crusher (HRC), variable speed ball mills and variable speed crushers. In addition to the innovative design, FMI commissioned the Metso APC team to design a realistic process simulator and the plant APC. The process simulator was utilized to train operators before commissioning, which led to a smoother plant start up. The plant APC utilized the concept of dynamic constraint control, which controls the feed to the primary ball mills by “pulling” the tons from crushed rock storage bins, which then automatically are filled by the upstream HRC and secondary crushing circuits. The primary ball-mill control also adjusts the water addition to the cyclone clusters to avoid overload and achieve sufficient grind size. The constraints include in-circuit constraints for feeder capacity, screen-deck capacity, ball mill power, cyclone mass flow, pump capacity and pump motor capacity. The APC system was implemented shortly after the start of commissioning and immediately demonstrated increased throughput and an ability to highlight and quantify process constraints and bottlenecks. The following paper outlines the control strategy, discusses system implementation, results and challenges.INTRODUCTION The FMI Metcalf Concentrator is located in Morenci Arizona on the site of the old original Concentrator. The new Metcalf concentrator started operation in May of 2014. This plant was designed for an average of 63,500 tpd (70,000 stpd), increasing the total Morenci concentrator complex production to a nominal 113,400 tpd (125,000 stpd). The process flow diagram is shown below in Figure 1.The process consists of primary crushing feeding a coarse ore stockpile followed by secondary crushing operating in closed circuit with vibrating screen decks. The screen undersize feeds the first of its kind Metso hydraulic roll crusher (HRC) operating in a closed circuit with vibrating screens. The primary crusher is a Metso 60x110 gyratory crusher. Secondary crushers are Metso MP1250 Crushers with variable speed drives. Secondary crusher discharge is recycled to the dry screen feed bin and screened with oversize returning to secondary crushing and undersize feeding the Metso HRC3000. The product from the 3.0 meter X 2.0 meter roll crusher is wet screened with the undersize feeding the grinding circuit, which is comprised of two each 24-foot diameter by 40- foot-long variable speed ball mills running in parallel with each in closed circuit with a cyclone bank of 12 cyclones. The wet screen oversize is recycled to the HRC feed bin."

Jan 1, 2019

By W. E. Oching, M. M. Ghomshei

"Collaboration among Ventilation Engineers, Mine Inspectors, worker representatives, health and safety officers and management is key to an effective operational mine ventilation management. Mine ventilation training, ventilation survey reports for mine stakeholders and interaction with mine frontline workers and management concerning safety, energy saving, assets management and maintenance are effective tools in implementing best industry practices and significant reduction of ventilation operating costs without compromising safety. These approaches may not be new to well established mining companies but the real dilemma is how to implement them effectively and this is what this paper will address.INTRODUCTIONManaging an effective mine ventilation system is becoming increasingly challenging, especially during tough economic times in the mining industry. Management strives for more production while frontline miners work hard to surpass the production targets, thus improving their incentives and above all aiming to enhance the prospects of their job security when the mining industry is facing challenging times. Taking shortcuts by not fully following the safety regulations or industry best practices are often notable, resulting in the rise of Workers Compensation Board claims and temporary shutdowns of active workings, compromising productivity and increasing the operating costs.In accordance with the Mines regulations in various jurisdictions in Canada and the US, it is evident that companies adhere to establishing basic ventilation management systems through the provision of the code of practice, procedures, work practices and standards/guidelines. This is aimed at ensuring the health and safety of underground workers (de Souza, 2017). However, the challenge to many operations is the improper implementation of the mine ventilation regulations including some managers showing reckless disregard for workers safety by focusing on production and not worrying to address ventilation problems (Steven & O'Keefe, 2010). Other challenges facing effective ventilation management include inadequate training of frontline workers on ventilation system and hazards associated with poor ventilation systems such as toxic gases, dust, heat, and underground explosions (Mufson et al., 2010; Suvar et al., 2017); friction between mine managers and the mine inspectors (Mufson et al., 2010), improper maintenance of ventilation system and inventory management, among others."

Jan 1, 2019

By J. C. Salas, A. Weishaupt, J. A. Guzman

The origins of the electrorefining process date back to 1869, when the first ER cathodes were produced at Pembrey, South Wales. By the time that Pembrey was closing, Chuquicamata tank house was under construction, initiating in 1915 a long history of electrolytic cathodes production. Initially electrowon cathodes and later electrorefined cathodes were produced. During the history of Chuquicamata tank house, there have been several challenges associated with the quality demanded for electrolytic copper. Among them, the transformation from electrowinning to electrorefining in 1952, the onset of the direct commercialization of ER cathodes and the phase out of wire bars in the 80s, several technological changes including the implementation of permanent cathodes, and certainly the constant increase in complexity of the anodes refined. This paper explores the manner in which Chuquicamata has addressed these challenges and examines its links to process characteristics, which have been necessary to maintain a product quality according to market requirements and a brand, “CCC”, that is widely recognized worldwide. INTRODUCTION Located in the north of Chile, in the Atacama Desert, Chuquicamata is an open pit copper mine that for many years has played a relevant role in the global and local mining industry. Known from prehispanic times, the Chuquicamata deposit was initially developed between 1912 and 1915 by the Chile Exploration Company, the operating company of the Chile Copper Company controlled by the Guggenheim Brothers in the USA (Yeatman, 1916). Officially inaugurated on May 18th, 1915, by the President of Chile who pressed a button in Santiago sending a telegraph signal to the power generation plant specially built in Tocopilla, 1500 km north. It signaled the beginning of generating energy, sending it to Chuquicamata, another 140 km east (“El mineral de Chuquicamata”, 1915), marking the beginning of its industrial operation.

Jan 1, 2019

By I. Paredes, R. Díaz, H. Henao

Smelting of copper concentrate generates a significant amount of dusts which are collected in electrostatic precipitators. This material, which is a complex oxide of Cu, Fe, S, As, Sb, Bi and others, is difficult to recirculate into the smelting process due to the reported high concentration of arsenic. However, the dust also has concentration of copper above 10wt %, aside from reported contents of silver corresponding as much as 25wt% of the total inventories of this element in the smelters. Thus, it is of economic and environmental interest the development of a process able to reduce the concentration of arsenic in the dust and produce a material suitable to be recirculated into the smelting process. The present experimental work shows the results of a process of dust sulfidization-oxidition able to remove more than 65wt% of the arsenic present. INTRODUCTION Copper sulfide deposits worldwide exhibit increasing concentrations of arsenic. One case of interest would be the copper ores from the northern zone of Chile, which report high concentrations of enargite (Cu3AsS4) (Revista química, 2015) (Latinominería, 2014). The obtained concentrate from this ore is treated in a Fluidized Bed Roaster, producing calcines with low concentration of arsenic (<0.5 wt% As). This material is suitable to be treated in a Flash Furnace. At the roasting process, the arsenic is volatilized and then precipitated as fine particles of complex oxides. Most of this particulate material is removed from the gas stream through a device called Electrostatic Precipitator (Minería chilena, 2014). The experimental results reported in the literature indicate that arsenic present in these particulate materials (or dusts) cannot be eliminated in oxidizing atmospheres (air) or with inert gases (N2) in a Fluidized Bed Roaster even at temperatures as high as 700°C. There is also information that even the recovery of valuable metals from the dust is difficult through hydrometallurgical processes (private communication). This is how in some foundries these dusts are considered environmental liabilities. Regarding the decomposition of enargite (Cu3AsS4) in neutral atmosphere, it is reported in the literature (Padilla, 2001) that the main chemical reactions are:

Jan 1, 2019

By W. W. Culver

The paper explores the substance, circumstances and significance of the Whelpley and Storer Copper Process. The 1866 Whelpley and Storer patent specified a process combining mechanical and chemical engineering. The process called for a down-drafting shaft furnace with a horizontal flue connected at the bottom of the shaft. Powdered sulphide ore was roasted in the shaft and then sent forward fully oxidized to a bath of sulphuric acid and/or calcium chloride. The “water furnace” was developed in Boston, at a time when the city was home to most Michigan copper mining companies. The process was field-tested at Quebec’s Harvey Hill copper mine. In 1865 James Douglas, Jr. took over management of the Harvey Hill mine with the challenge of saving the family investment. He needed a way to make money from low-grade sulphides. Through his relationship with chemist T. Sterry Hunt, Douglas learned of a possible way ahead using the process developed by Whelpley and Storer. The paper confirms the centrality of publications, meetings, and networking in the advancement of metallurgy. The process is of interest historically, as much as anything, because it is one of the pillars of James Douglas’ distinguished career in copper. INTRODUCTION At the 1866 meeting of the American Association for the Advancement of Science (AAAS) in Buffalo, New York, T. Sterry Hunt (1826–1892) read a paper “On the Metallurgical System of Messrs. Whelpley and Storer.” The paper is part of a chain of events that constitute the foundation of James Douglas’ (1837–1918) success in the copper mining industry. To understand the career of Douglas over the early years of modern copper mining, we must necessarily start with Whelpley and Storer. Going back to Hunt’s paper, he concluded his remarks by asserting that the Whelpley and Storer Process was “capable of such wide and varied application, that it is probably destined to have a very important influence on the industry of the world” (Hunt, 1867a). He reached this conclusion reasoning that the process had overcome a critical metallurgical hurdle (Hunt, 1867a). Hunt, a geo-chemist in modern terms, recalled that the chemist of those years easily separated copper from “sulphuretted” ores by converting it to a soluble salt from which pure metal was precipitated by “an equivalent of iron.” The problem was to “…apply this principle in the working of copper ores on a great scale...” (Hunt, 1867a). Hunt noted that this very problem had “…engaged the attention of many metallurgists, and has given rise to various processes for obtaining copper by the moist way, many of which are nearly or quite perfect in their operation, but are lacking in practicability and cheapness” (Hunt, 1867a). Hunt thought Whelpley and Storer had overcome the low-grade sulphide hurdle with a commercially viable engineering breakthrough. Yet in the history of copper metallurgy, the process is missing. What happened?

Jan 1, 2019

By Eduardo Lozano, Vilem Petr

This study demonstrates the ability of high-order, shock-capturing methods to simulate detonation wave propagation in right circular cylinders of non-ideal explosives. 2-D axisymmetric, reactive Euler equations were solved for the detonation of the highly non-ideal explosive ammonium nitrate-fuel oil (ANFO) using a simple pressure-dependent rate law and perfect gas equation of state. The fractional step method was applied to the convection and reaction operators using a 2nd-order Strang splitting. The flow solver consisted of a finite difference scheme where the flux is reconstructed by a modified fifth-order weighted essentially non-oscillatory (WENO5-Z) with local characteristic decomposition and local Lax-Friedrichs (LLF) flux splitting. Time integration was performed by a third order total variation diminishing (TVD) Runge-Kutta time discretization method, also known as the strong stability preserving (SSP) method

Jan 1, 2019

By T. Gonzales, M. Maleki, M. Caçador, B. Climenhaga, H. Ghorbani

The campaign life of furnaces in the copper making industry is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper monitoring and assessment of the existing conditions and safe remaining life of the vessels and their refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a typical fitness-for-service assessment of a rotary vessel shell in order to extend the campaign life of copper making furnaces and enhance safety. The furnace refractory management system involves a comprehensive audit and monitoring program which has been successfully applied to several copper flash smelting furnaces over the past 15 years. The fitness for service assessment provides a methodology to estimate the remaining life of the steel components by evaluating the existing damage and future damage rate based on the historical survey data. The above practices can provide the operator with cost savings by extending the vessel campaign life in lieu of implementing more rigorous refractory lining and shell audits. INTRODUCTION Primary copper smelting is generally divided into two categories of flash smelting and open bath smelting. There are many different types of vessels that can be used to convert the copper concentrate to blister copper including, flash, Mitsubishi process, TSL (ISA/Ausmelt), SKS Bottom Blowing, Anode and Teniente/Noranda furnaces, reactors, and Peirce Smith converters. Each vessel has its own complex and intense environment which requires careful refractory and steel design to withstand the severe thermomechanical and thermochemical attacks within its campaign life. The campaign life of furnaces is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper assessment of the existing conditions and safe remaining life of the vessels and/or refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a fitness-for- service assessment methodology to estimate the remaining campaign life of copper making furnaces resulting in cost savings and enhanced safety of the operating vessels.

Jan 1, 2019

By Martin G. Wafforn, George J. Greer

"In early 2014, Pan American Silver Corp. commenced a project to construct a second shaft at its La Colorada underground mine located in Zacatecas State in Mexico. This was the first new shaft development project undertaken by Pan American Silver in the history of the company. The existing mine workings permitted the use of a raise bore for the excavation of the shaft opening, utilizing directional drilling in poor ground conditions to advance the pilot hole. This was an interesting project with many challenges and successes, and numerous lessons learned. The project was successfully completed in 2016, with the shaft operating at full mine production capacity within weeks. INTRODUCTION The La Colorada Mine has a long history dating from at least the 1920’s. The mine is located in the northern portion of Zacatecas State in Mexico in the Chalchihuites area, an approximate two hour drive south from the city of Durango. Pan American Silver acquired the La Colorada mining concessions in 1998, with mine production at that time consisting of only a few hundred tonnes per day. Over the course of the following 15 years, with the addition of an oxide processing plant and some expansions to the sulphide processing plant and site infrastructure, production was eventually increased to a maximum of 1,250 tonnes per day, all of it generated from conventional cut-and-fill stopes in the underground mine. An existing shaft was used to hoist the ore to surface, and over the years Pan American Silver had deepened the shaft and had changed out some of the hoisting plant. However, there were historic workings in close proximity to the shaft that made it unsuitable for personnel transport, and shaft maintenance was becoming difficult. The shaft was increasingly considered as a risk to the long term production continuity, and also to further deepening of the mine. In addition, expanding the capacity of this old shaft was not possible. Drilling of the La Colorada mineralization at depth commenced in 2010, with very good exploration success. As a result, by the end of 2013, the mine reserves had grown to a total of 6.5 million tonnes of high grade ore (388 g/t Ag, 0.36 g/t Au, 2.4 % Zn, and 1.3% Pb). Furthermore there were more (and higher grade) sulphide reserves than oxide reserves at depth. Following the completion of an internal study in 2013 with assistance from one of the international shaft contractors, a decision was made to increase the production from the mine with the construction of a new shaft and a new sulphide processing plant, a project with a calculated payback of 2.2 years."

Jan 1, 2019

By Joey Hoang, Robert Johansson, Tapani Keronen, Mikael Jåfs, Jani Jansson, Mikko Korpi

At the Copper 2016 conference in Kobe, Japan, Outotec introduced a vision for the year 2020, wherein smelting would make use of four digital cornerstones: intelligent instruments, advanced process control, improved information management and transparency of and access to data. Since then, this vision coined the phrase “Fully Automated Smelter” with the mission promising a concept where no manual actions from human operators would be needed during normal smelter operations. Replacing repetitive physical work, collection and analysis of everyday production data has a great potential for further automation and will provide productive ways to improve efficiency and safety of smelters in the future. Therefore, a lot of emphasis has been put into developing solutions to automate these tasks and to move people out of harm’s way. A lot of new equipment, systems and optimization tools are under development. In addition, a lot of effort is going into developing dynamic process models and advanced control systems to interface with the plant automation systems. The goal is to integrate all these concepts to meet Outotec’s Fully Automated Smelter vision. This paper will cover these latest achievements toward this vision and introduce the near-future of digital smelting. INTRODUCTION As is well known already, the humankind is currently experiencing a change, extent of which is broadly studied by the governmental, educational and industrial institutions and parties. The wellbeing and quality of life have traditionally been improved alongside the developments in industrial production, which is now about to enter its fourth revolution. Therefore, the current change is often described as fourth industrial revolution, or industry 4.0 (or industrie 4.0, as named by Acatech, 2013) and can be considered anything from small incremental development to a ground-breaking global reset that will affect everyone’s lives. Many seem to agree, that the scale of change will indeed be big, even significantly bigger than the three industrial revolutions before it (Pellini, Weyrauch, Malho & Carden, 2019; Geissbauer, Vedso & Schrauf, 2016; Jansson, Bjorklund, Lahtinen, Heinonen, Jafs & Fagerlund, 2016).

Jan 1, 2019

By D. Tetsuka, H. Okamoto

The amount of impurities to be processed in a copper smelting process has increased for recent years because of an increase in the electronic scrap amount. It has been found that Sb and Ni effect on the operation of our copper electrorefining process. It is found that the current efficiency of the copper electrorefining tended to be decreased as the Ni concentration in the electrolyte increased. The passivation of the process seemed to be more related to SO4 concentration in the electrolyte rather than the Ni concentration in it. The current efficiency decreased when the Sb content in the anode was high. A high Sb content in the anode caused easy passivation by forming a gel-like film in the slime layer. We have developed a method to for see the anode passivation in a short time while generating a slime layer. We confirmed the tendency of passivation through the experiment of changing Pb content in anode. Passivation was easily occur with an increase in Pb content in the anode. The amount of slime increased as the Pb content in the anode increased. This suggests that passivation was facilitated because liquid diffusion near the anode was inhibited. INTRODUCTION The amount of impurities to be processed in copper smelting has been growing in recent years because the amount of electronic scrap has increased. Figure 1 shows that the contents of Sb and Ni in copper anodes have increased since 2007.High Sb and Ni contents in the copper anode decreased the current efficiency of the process and made the quality of copper cathode poor because of the anode passivation and the formation of floating slime in the electrolyte during electrorefining. If these influences of impurities are suppressed, it would be possible to make copper electro-refining current density higher and to process much amount of electronic scrap. We examined the components of our copper electro-refining process like anode composition, slime properties and electrolyte composition, and investigated the mechanism by which Sb and Ni affect passivation and current efficiency. When examining the influence of Ni, we noticed that the SO4 important. The effect of SO42 – was also discussed

Jan 1, 2019

By J. Gustavsson, S. Holmin, Å. Afvander, E. Rosseland, E. Zimmerman

There are numerous advantages in replacing lead-based anodes with mixed metal oxide (MMO) coated anodes in copper electrowinning; for example, lower energy consumption, improved working conditions for operators and less environmental impact. Since 2012, Permascand AB in Ljungaverk, Sweden has evaluated Permascand coated titanium anodes in copper electrowinning pilot trials at Glencore Nikkelverk in Kristiansand, Norway. The investigation has proceeded in three different steps (Phase I, II and III). In Phase I, different Permascand coatings, electrode structures and coating methods were investigated. The results showed that improved current distribution, lower energy consumption and longer service life could be obtained with expanded mesh electrode structure in a box configuration compared to rod anodes in a single-mode construction. In addition, improved current distribution and less coating wear was found when electrostatic spray coating was used instead of brush (manual) coating. It was also found that the extrapolated service life from controlled lab experiments at 200 A/m2 was much shorter compared to what was experimentally obtained in copper electrowinning pilot trials at similar current densities. This was mainly attributed to different coating failure mechanisms in lab and industrial copper production. INTRODUCTION Traditionally lead-based anodes have been used in copper in electrowinning due to lower cost. But there are many advantages in replacing lead-based anodes with mixed metal oxide (MMO) coated titanium anodes in copper electrowinning, such as lower energy consumption, higher corrosion resistance, improved working conditions for operators and less environmental impact. Still, many facilities are using lead-based anodes, although the progression of using metal oxide coated anodes in copper electrowinning has slightly increased (Robinson et al., 2012).

Jan 1, 2019

By Avi Nanda, Robert Brandt, Alex Piatkiewicz, David M. Jones

In 2010 the United States Environmental Protection Agency (UESPA) revised the National Ambient Air Quality Standards (NAAQS) by lowering the permissible value to a 1-hour average SO2 concentration of 75 ppb. In 2012, the USEPA designated the Miami area as non-attaining for the new SO2 NAAQS. A number of options were studied to assist in bringing the Miami smelter into attainment with the new standard. The chosen solution included: Installation of a large tertiary hooding system over the converter aisle; Hooding of the anode vessels and treatment of the anode gas in a baghouse; Installation of a large 2,325,212 Nm3/hr caustic scrubber to treat the captured converter fugitives and anode off-gases; Installation of a secondary ESP for the tapping fugitive off-gas treatment system; and the continuous scrubbing of all acid plant tail stack gases. The modifications have reduced smelter SO2 emissions by 85%, achieving a world class SO2 stack emissions rate of 0.45 kg of SO2/tonne Cu. INTRODUCTION The Freeport McMoRan Miami smelter has been previously described in literature (Steinborn, Pasca, Sallee, Binegar, Bhappu). For the sake of brevity a brief description is given here. The Miami smelter is located 129 km east of Phoenix, Arizona near the town of Miami, Arizona. The smelter was established in 1915 and has undergone a number of process upgrades and modernizations over the years. The present smelter consists of an Isasmelt furnace, an electric settling furnace, four Hoboken converters, two anode refining vessels & one casting wheel; and one double contact sulfuric acid plant. Concentrates are railed & trucked to Miami from four Freeport McMoRan mines located in Arizona & New Mexico. The wet concentrates, typically containing 10% H2O with a Cu/S ratio of 0.85, are smelted in an Isasmelt furnace to a matte grade of 58%. The entire output from the Isasmelt is laundered into an Elkem electric furnace (originally installed in 1972 as the primary smelting furnace) for separation into matte and slag. Slag containing 0.85% Cu is skimmed from the electric furnace and discarded. Molten matte, containing 60% Cu, is tapped from the electric furnace and processed in one of four Hoboken converters to produce blister copper. Two anode refining vessels further refine the blister copper before the final product is cast on a single, 30 mold, casting wheel. All of the anodes produced at Miami are shipped to the Freeport McMoRan electrolytic refinery in El Paso Texas for refining into cathode copper. Smelter off-gases from the Isasmelt, electric furnace and Hoboken converters are combined and treated in a double contact acid plant to produce sulfuric acid. Acid produced at Miami is internally consumed at Freeport McMoRan mines in the region.

Jan 1, 2019

By M. Sommerfeld, U. Schwarz-Schampera, B. Friedrich, D. Friedmann

The steadily growing demand for metals and their price increase at metal exchanges make the mining and utilization of marine mineral resources like polymetallic nodules, manganese crusts or sulfide deposits in the near future a viable option to potentially increase the supply of base and precious metals. For a country with low potential to mine land-based resources like Germany, the industrial recovery of metals from marine mineral resources could lead to a decreased dependency on imports. In this study, seafloor massive sulfides from the German license area in the Indian Ocean (Kairei field, Southern Central Indian Ridge) are treated to recover copper and precious metals. The aim of the project is to demonstrate the transferability of existing metallurgical techniques to the raw material of deep-sea massive sulfides. As a starting point to process this unconventional resource, samples from the Indian Ocean are chemically analyzed and mineralogical characterized. A comparison is carried out between the samples and land-based copper resources, to highlight the potential which lies in mining the deep-sea floor. This paper will show the general possibility of applying a two-stage pyrometallurgical process, based on a concentrate smelting operation, followed by a converting operation in lab-scale to the provided samples of massive sulfides. Generated slag from the concentrate smelting and the converting operation are investigated by X-ray diffraction to determine the mineralogical composition. The two-stage pyrometallurgical process is investigated by the thermochemical modelling tool FactSageTM 7.2 to evaluate the phase distribution of relevant elements between the metal, matte, slag and gas phase. The thermochemical boundaries of the pyrometallurgical process are therefore set and the results of the thermochemical study can be used as an indicator for the efficiency of an up-scaled process and the generated amount of side-streams, which need to be further treated or circulated back into the process. INTRODUCTION Seafloor massive sulfides (SMS) are the third kind of discovered deep-sea minerals besides ferromanganese nodules and cobalt-rich ferromanganese crusts (Sharma, 2017). They occur in water depths around 250–4,000 m (Koschinsky et al., 2018). SMS are characterized by a high base metal and sulfide content. They were created by fluid circulation and hydrothermal convection over time (Han et al., 2018). Commonly, areas rich in SMS are associated with hydrothermal vent fields on the seafloor (Keith et al., 2018).

Jan 1, 2019

By William M. (Bill) Shaver

"The author will review the early history of shaft sinking as well as focus on the improvements made in shaft design and construction over the last fifty years (1970 to 2019) to predict how shaft sinking will change over the next fifty years and describe what the shaft sinking world might look like in 2070. INTRODUCTION It is a great honour to be one of your keynote speakers for the Fourth International Conference on Shaft Design and Construction being held in Toronto in November 2019. This is one of the opportunities we have to thank the Mining Companies of the world as well as the industries and companies we serve for their support of the mining contracting and shaft sinking business of Canada and the world at large. Many of these companies are represented here today. Without your support many of the innovations we will talk about today would not be possible. We would also like to thank all the companies that work with us in our business including all the contractors and suppliers who provide the various services we require. These include equipment manufacturers, engineering companies, project management companies and suppliers large and small who cater to our every need as quickly as possible. Without all these partners we would not be as good as we are. Many of these companies are our sponsors this week. Thank you from all of us! This is also an appropriate time to pause and think about those Shaft Sinkers we have lost and those who have been injured on our projects around the world. Please bow your head and remember the Shaft Sinkers you have worked with, who did not return home or those who returned home injured. Think about how we can continue the work of making shafts safer every day as we go forward with our projects so everyone goes home to their families safe and sound. Pause for a minute and thank you. The subject matter we have chosen to discuss today is “Shaft Sinking in the Next Five Decades”. How will the work be done, how fast will it be done, what will it cost, and why we think this may occur? It is appropriate to consider this over the next few days with this auspicious group we have assembled. Today, we will look back at all the advances that have been made over the last many years and look ahead to the future to attempt to predict what shaft sinking will look like in 2070. When I look around the room I recognize that many of us will not be around then so we need not worry about being wrong. Suffice it to say that the next 50 years will be very interesting and exciting for the shaft sinking business."

Jan 1, 2019