Search Documents

By Pedro Henrique Vasconcellos Apipe

O objetivo do trabalho consistiu em estudar os modos de transmissão de calor existentes em um conjunto mecânico composto por um rolo de extração e mancais de contato rolante em decorrência do movimento de um tubo laminado sobre o mesmo na planta da Vallourec Brasil. A motivação para o estudo surgiu na avaliação de como os fenômenos térmicos presentes resultariam na distribuição de temperatura através da superfície do conjunto e qual a sua relação com a disponibilidade desse equipamento. Para isso a análise desenvolvida foi baseada no emprego da dinâmica dos fluidos computacionais (CFD), associada a imposições subsidiárias durante a definição das condições de contorno do problema. Como resultado a distribuição de temperatura através da superfície do conjunto foi determinada, sobretudo na pista interna do rolamento e na região na qual se encontra o sistema de refrigeração. Desse modo conclui-se que embora o sistema de refrigeração dissipe uma grande quantidade de calor a sua eficiência não é satisfatória. Fato esse descrito pela presença de temperaturas superiores as necessárias para a ocorrência do fenômeno de ponto de gota.

Jul 31, 2018

By Dyego Monteiro de Souza

This study compares the wear resistance of specimens lubricated with biofluids or mineral oil. Tribological studies were performed by ball-cratering test. In these tests were used as lubricants epoxidized soybean oil, castor oil and mineral oil. The specimens used were untreated and nitrided AISI 4140, while a steel ball AISI 52100 was used as a counterbody. In order to analyze the results obtained, the worn volume was calculated and the characterization of the crater, after the test, was made using optical microscopy and SEM. Wettability was also measured for the different surface condition and lubricants. As expected both specimens showed a smaller volume worn when lubricated with mineral oil due to inherent properties of this type of lubricant. Among the vegetable oils studied, the castor oil showed a better performance in the lubrication of the specimens untreated while on the nitrided specimen have shown less wear when lubricated with epoxidized soybean oil, indicating a difference in the efficiency of oils, as lubricants, depending on the surface conditions of the mechanical components.

Jul 31, 2018

By Lis Nunes Soares

A Vallourec Tubos do Brasil é uma siderúrgica integrada com produção de tubos de aço sem costura. A qualidade e o acabamento superficial dos tubos estão diretamente relacionados com o processo de laminação pelo qual eles passam. Um fator extremamente importante para um bom processo de laminação é uma boa lubrificação da peça de laminação, o mandril. Durante o processo de laminação, o mandril passa por várias etapas além da lubrificação, incluindo etapas de aquecimento e resfriamento, que se repetem em ciclos de laminação. Um dos principais parâmetros do processo de produção que influenciam a lubrificação do mandril é justamente o perfil térmico e a temperatura superficial do mesmo. O perfil térmico do mandril afeta a aderência do lubrificante em sua superfície. Visando a melhor compreensão do processo, esse trabalho tem como objetivo propor um modelo matemático em diferenças finitas que descreva a evolução do perfil térmico do mandril durante o processo de laminação de tubos sem costura. O mesmo modelo matemático é validado através de engenharia reversa. A proposta do modelo matemático é ser usado na análise de possíveis métodos de pré-aquecimento de mandris antes da lubrificação, diminuindo ou eliminando assim possível sucateamento de peças e paradas da linha de produção por esse motivo.

Jul 31, 2018

By Washington Martins da Silva Júnior

In stamping process, sliding between metal sheet and forming tool leads to wear of tool surface. Maintenance of stamping tools involves polishing the tool edge, or, in case of severe damage, replacement of the tool. Hard coatings have been applied on the stamping tool surfaces in order to reduce the maintenance cost causing a great economic impact in metal work industry. In this work, CrAlSiN coatings were applied by PVD onto SRV2W tool steel. The coating toughness was avaliated by the critical load in scratch tests. The following coating parameters were analyzed: 1- substrate surface finishing process; 2- coating architecture (multilayer or gradient); 3- chemical composition of the coating. AlSi concentration varied from the substrate/coating interface to the surface. Coatings were 3 µm thick. Scratch tests were carried out using a Vickers indenter. The applied normal load was varied from 0 to 13 N for a scratch length of 5 mm. In order to study the effect in the toughness, the substrate roughness was controlled by the finishing process before PVD coating. Samples subjected to polishing presented highest critical loads. Gradient coatings presented higher critical loads than those with a multilayer architecture. Coatings with higher concentration of AlSi near the surface supported higher loads before failure.

Jul 31, 2018

By Angelo dos Reis Magalhães

Brazilian companies have adopted in recent years new management practices to remain competitive. Specialized consulting in asset management progressively creates or adapts new techniques in order to increase availability and reduce manufacturing costs, maximizing profits. New engineering concepts were acquired and implemented by executives in all business segments. Techniques, such as FMEA, RCM, LCC, Pas 55, Reliability studies by Monte Carlo simulations, among others, have become increasingly recognized as important tools to enhance managerial performance. Besides these techniques, this study suggests the importance of adequate structuring of a lubrication program, as a critical success factor for the reliability of any asset. Through a case study developed with a company in the mining sector, this work proposes the development of a master plan for lubrication based on three pillars: People, Equipment and Management system. Practices and care with lubricants, hydraulic fluids and coolant, until its point of application, shall be evaluated to ensure a correct contamination control and a high level of assets availability. This discussion sheds light onto other benefits of this process, including occupational health and safety; ergonomics; environment and sustainability.

Jul 31, 2018

By Lionel Loïc Limol

Polymeric materials, such as polyurethanes and rubbers, are widely used in the mining industry because of their moderate cost and excellent mechanical properties. Such polymers have been used mainly in transportation (conveyor belt systems and pipes coatings) and screening, for their appreciable abrasion wear resistance. Studies revealed the complex influence of test parameters, such as grit size and applied normal load, on the abrasion wear process for polymers. In this study, the abrasive wear behavior of several polyurethanes and rubbers were investigated at room temperature according to a rotary drum abrasion method (DIN 53516). Wear tests were carried out at 26 cm/s test speed and load value of 5 N and 10 N. Corundum paper grit varying from 60 to 400 mesh were used as an abrasive surface. After each test the mass loss of the pin was recorded and the wear rates were calculated from wear volume. The wear surfaces were investigated by scanning electron microscopy.

Jul 31, 2018

By Ródnei Abbade Abreu

A UPV é abastecida basicamente por duas fontes de energia elétrica de 60 Hz (maioria das cargas da usina): LIGHT (concessionária - externa) e CTE#2 (interna). A energia externa chega a UPV via sistema de transmissão e distribuição da LIGHT, por esse transporte paga-se uma tarifa de uso do sistema para a concessionária, vale ressaltar que não é comprado energia da LIGHT e sim o transporte da mesma, a energia é comprada de unidades geradoras distantes da UPV. O valor pago pelo transporte da energia é baseado em um contrato de Demanda [MW], que representa um valor máximo que o sistema deve ser capaz de suportar, caso seja solicitado. O objetivo desse trabalho é identificar qual a melhor (menor) demanda a ser contratada pela UPV, de forma a atender os processos produtivos e não ultrapassar o valor contratado (pagamento de multa), para tal foi criado um simulador com base em dados históricos para estimação de demanda a ser contratada pela usina.

Jul 31, 2018

By Gustavo Borges Tiboni

The erosive wear caused by the impact of solid particles against a surface is a tribological phenomenon present in many segments of the industry, such as transportation, aerospace, mining, power generation, among others. The most usual method to set the wear rate is by measuring the mass loss of the material. In order to apply one technique with potential to determine the rate of erosion wear, this study developed a dedicated equipment and conducted preliminary erosion tests monitored by non-destructive testing known as acoustic emission technique (AE). This can be defined as a technique able to detect mechanical waves generated by the release of elastic energy accumulated in the material. Erosion tests were performed in order to evaluate the ability of equipment to collect data from AE and to correlate these data with the wear of the samples. Samples of low carbon steel eroded by the impact of angular aluminum oxide particles suspended in air at three different velocities: 45, 57 and 67 m/s. The impact angle between the particles and the sample was set at 30 degrees and the test temperature at approximately 20°C. The wear rate has changed with the velocity in accordance with the kinetic energy of the particles and the AE parameter RMS showed sensitivity to the variation of particle impact velocity and to the wear of the sample eroded. The rate of AE signals collected over time correlated with the flow of particles striking the sample, and with the parameters of energy, rise time and duration of the signal.

Jul 31, 2018

By Augusto César Barrios Tamayo

The high temperature erosion of Thermal Barrier Coatings (TBCs) is one of the main factors that define the lifespan in gas turbine components as it is considered the second source of failure of hot path components in power and propulsion turbine operation. The worn Top Coat (TC) surface in components such as first stage turbine blades affects the turbine efficiency due to energy losses and the increment in heat transfer to substrate. The first part of this work consists in describing a HTE test facility developed to emulate the damage conditions found in a number of components of gas turbines; in this testing machine, the samples were exposed to combustion gases moving at velocities close to 1.5 Mach and temperatures of 1100°C. The second part consists in the characterization of liners and first stage turbine blades of a GE7FA gas turbine used for power generation. The last part deal whit correlation of the features of TC’s worn surfaces with the erosion conditions and the dominant degradation mechanisms between test samples and turbine components were compared.

Jul 31, 2018

By Diego Berti Salvaro

The morphology, dimensions and chemical composition of tribolayers strongly depend on the pressures and temperatures acting on the contact. They are formed by reactions between the surfaces in contact with each other as well as with the atmosphere, lubricants and possible contaminants. In this paper the influence of test time (180, 500, 1000 and 2500 h) into the formation and characteristics of tribolayers in pairs DLC-stainless steel tested under refrigerant gas R134a atmosphere without presence of lubricating oil was analyzed. The characterization was performed using scanning electron microscopy, energy dispersive spectroscopy (SEM-EDS) (morphology and chemical composition) and white light interferometry (dimensions). The tribolayers thicknesses ranged from 100 to 500 nm and they were composed by elements originated from mutual transfers between the tribological pairs as well as oxides, being more pronounced on the stainless steel surface. The results show that the tribolayers are chemically stable (maintained the same composition over time) and the thickness remained stable after a thousand hours of testing.

Jul 31, 2018

By Samuel Vasconcellos

Em plantas de separação do tipo PSA ocorrem oscilações na vazão de ar intrínsecas a este processo, devido à repressurização dos vasos pré-purificadores ser feita em intervalos muito curtos. Por meio da instalação de um buffer tank foi possível tornar a coluna de destilação mais estável, aumentando a produção de líquidos, reduzindo a demanda de energia e otimizando a pré-purificação.

Jul 31, 2018

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By Aperam South America

Balanço Energético Global e Utilidades - 2013

Jul 31, 2018

By Gerdau Ouro Branco

É apresentado o Balanço Energético Global da Gerdau Ouro Branco 2013, com os principais indicadores de consumo energético das áreas produtoras. Além dos indicadores energéticos globais, o balanço apresenta os consumos físicos específicos de cada insumo nas diversas áreas, permitindo a análise de cada setor da usina isoladamente. Destaca-se em 2013: -Início de operação da Laminação de Tiras a Quente. -Menor participação do Lingotamento Convencional. -Menor produção de aço bruto da usina em relação a 2012.

Jul 31, 2018

By Robson Gambeta

A CLE Brasil possui uma subestação de 230kV que apresentou sérios problemas de trincas e rachaduras nas estruturas de concreto após alguns anos. Em alguns pontos a ameaça de queda era real. Foi iniciado um estudo de patologia das estruturas de concreto, com uma empresa especializada em recuperação estrutural para conhecer as causas e recomendar a melhor terapia estrutural a ser realizada. Após o estudo, definiu-se a terapia adequada das estruturas. Esta atividade foi classificada como de grande risco e teve foco na segurança da equipe e operação do sistema, de modo que todo o serviço fosse executado sem quaisquer incidentes as pessoas, ao meio ambiente e ou interrupções de energia elétrica. Havia desafios como realizar manutenção nas proximidades da linha viva, serviços em altura com utilização de andaimes, período de chuvas e ventos, trocas de equipes e anomalias. As estruturas tratadas foram Pórticos com 17 metros de altura, postes e suportes para isoladores, TPs, TCs, Seccionadoras e Transformadores. A atividade durou 04 meses e contabilizou 5.752 horas de trabalho. Os resultados foram significativos e dentro do esperado, sem ocorrência de incidentes, prolongamento da vida útil e aumento considerável da segurança da equipe e do sistema de distribuição.

Jul 31, 2018

By Luiz Henrique Accorsi Gans

First, this works carries an experimental evaluation for austempered ductile iron (ADI) as a gear material. And second, in order to provide a better understanding of the microstructural effect on the stress state of subsurface regions, a finite element method approach was considered using the submodeling tool in ANSYS 11.0. For this, ADI gears were produced from continuous cast iron bars, heat and thermochemical treated and tested in FZG test rig. The results were compared to those of carburized steel AISI 8620 and induction hardened steel AISI 4140 gears. The wear experiments were performed at the temperature of 90ºC with two torque stages: 135 N.m (running-in) and 302 N.m (steady-state). The time for pitting and spalling on the gears surfaces were measured using image analysis. The results showed a very good potential of using ADI for manufacturing gears, replacing induction hardened steels. Also, the ADI gear with smaller nodules showed higher life for pitting. In contact fatigue tests with severe load, the carburized AISI 8620 steel proved more adequate than the austempered ductile iron, showing that the mechanical properties are critical in the resistance to damage in gear contact. The austempered ductile iron with smaller nodule size showed to be very competitive with wear resistance similar to AISI 4140 steel induction hardened. With ANSYS, it was verified that the nodule size affects the gears life independently of the mechanical properties of the matrix. The results showed that the nodules indicate the presence of a concentration stress, but their size doesn’t affect the contact fatigue life as much as the total amount of nodules, regardless of the ductile iron microstructure. The size and number of nodules affects both the nucleation and the propagation stage of cracks. ADIs with higher amount of nodules have a greater wear resistance. Also, compared to the Hertz contact theory (isotropic material), the presence of graphite nodules indicates a non-isotropic material and made the maximum shear stress point moves toward the surface.

Jul 31, 2018

By ArcelorMittal Tubarão - Aços Planos

Fatos Relevantes - Produção anual de 4.491.854 t de aço bruto - produção estável em relação à 2012. - Produção anual de Bobinas Laminadas a Quente de 3.726.871 t - 7,8% de elevação em relação a 2012. - Unidades Geradoras da Central Termelétrica em manutenção aproveitando período de menor produção relacionado à parada do Alto Forno 3. - Redução relevante na geração de energia elétrica interna devido menor disponibilidade de combustíveis (off-gas) e redução de produção na Sol Coqueria adequando à demanda de coque do grupo ArcelorMittal Brasil.

Jul 31, 2018

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By Kelen Juliane Mucelin

In order to better understand the tribological behavior of self-lubricating materials, Fe-Si-C matrix composites containing solid lubricants added during the mixing step were studied. The samples were produced by conventional powder metallurgy route, presenting total contents of 5%, 7.5% and 10% in volume of h-BN and graphite mixtures as solid lubricants. The composites were evaluated in terms of tribological properties, under reciprocating sliding conditions, and mechanical properties by using tensile tests. Additionally, the wear scars were characterized by Raman spectroscopy and scanning electronic microscopy. Higher total contents of solid lubricants greatly increased scuffing resistance however decreased mechanical properties. Furthermore, increasing h-BN contents reduces both properties. These results confirmed the applicability of such sintered composites as self-lubricating parts, reaching values up to 7000 N.m for scuffing resistance combined with ultimate tensile strength of 220 MPa.

Jul 31, 2018

By Luiz Antônio da Silva

Este trabalho tem como objetivo apresentar os resultados do procedimento de geração de energia elétrica adicional a geração econômica na CTE2 com gás natural, visando a redução de custo no grupo CSN.O estudo foi efetuado através da avaliação dos preços do mercado de curto prazo de energia elétrica e análise do processo de geração da planta, aos quais permitiram diagnosticar as melhores praticas e definir a melhor configuração operacional.Os resultados apresentados foram significativos para as condições de operação, o que representa redução do custo de energia elétrica para o grupo CSN e aumento da segurança operacional da planta da CTE2.

Jul 31, 2018