Search Documents

By R. L. Every, A. G. Fonseca

"Sulphur deposition on the internal wall of a pipeline is caused by the temperature effect on the solubility of sulphur in the carrier fluid and is not due to particulate sulphur present. Deposition can be completely eliminated by proper insulation of the pipeline to prevent ""cold-spots"" and the resultant temperature gradient necessary for sulphur to precipitate from solution. Friction head losses for sulphur-condensate slurry systems are quite acceptable from a technical and economic standpoint and, in fact, are less than many present commercial slurry systems. Slurry transportation of sulphur in a hydrocarbon pipeline is a viable possibility and promises to have economic advantage over currently accepted transportation modes."

Jan 1, 1972

By Foster Fraas

Most commercial electrostatic separators utilize the electrical property of conductivity, but although based on the same principles, they are constructed in a variety of forms, a common one being the simple roll type. Some information obtained during an investigation of that type of separator, and which indirectly is applicable to other types, is presented here. In Fig. I material discharged from hopper 6 is fed onto grounded rotating roll 2. Electrode 3 is at a high electrical potential with respect to roll 2, and any conductive particle in contact with roll 2 therefore acquires an electrical charge of such polarity that, when present in the electrical field, the force on it is in the direction of electrode 3. A detailed description of the charging by conductance as utilized in electrostatic separators may be found in a previous publication.' As a result of this force, the path of the projected particle is changed in increasing amounts in the direction toward region C as the magnitude of the charge is increased. With the dividing edge 4 the projected particles may be divided into two fractions —those in region C designated as "deflected" or"deflectant"and those in region B designated as "residue." When material is passed over the roll only once, a complete separation is seldom obtained, therefore most commercial separators contain several roll-separator units in series, and some practical machines use as many as I2. In this paper a "pass" means the passage of material over a single-roll unit. The procedure is to repass either residue B with a low potential on electrode 3 or deflectant C with a high potential on 3. Most electrostatic separations follow a flowsheet of roughing and cleaning either the concentrate or the tailing, or both. In a specific instance, a dry, heated mixture of wet cleaned chromite and garnet from an

Jan 1, 1943

By Georg Petersen

El Perú es un país rico en diversidad de metales empleados en los campos de la minería, metalurgia, orfebrería y artesanía durante los tiempos pre-históricos. Dichos metales son: oro (objetos laminados por martilleo, repujados, pulidos, vaciados, soldados y dorados), plata (objetos trabajados de la misma manera que los de oro), cobre (objetos en diversas formas, como son discos, recipientes, herramientas y armas, en muchos casos dorados y/o plateados) y el azogue (cinabrio usado preferentemente para pintar las caras de los guerreros, las máscaras de los fardos funerarios y las caras de las mujeres nobles, costumbre que se generalizó a principios de la época colonial). De otro lado, existen otros cuatro metales que se emplearon en cantidades pequeñas como: fierro, platino, plomo, estaño.

Nov 1, 1970

Bailey, Lewis Newton, Master Engineer, Senior Grade, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia at Camp Merritt, N. J., on April 30, 1.918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on October 7, 1915. Dougall, Ralph, killed in action Evans, Alfred Winter, Lieut.-Col., New Zealand_ Rifle Brigade, D. S. 0., D. C. M., killed in action on October 12, 1917. Hague, William, 1st Lieut., Engineer Officers' Reserve Corps, died in active service.

Jan 8, 1918

By L. W. Bahney

MANY methods for the determination of gold or silver, or both, in cyanide solutions have been published, which with care in manipulation, and modification in some cases, will give results that are satisfactory. It is possible to classify or group these methods as follows: 1. Evaporating the solution in a porcelain or agate-ware dish containing litharge,1 or in a "boat" made of lead foil. 2. Forming a lead sponge containing the precious metals by means of zinc shavings,2 zinc dust,3 or a piece of aluminum.4 3. Decomposing the cyanide solution with an acid and precipitating the precious metals by the use of one or a combination of some of the following: Copper sulphate,5 sodium sulphite,6 hydrogen sulphide,7 cement copper.8 4. Precipitating the silver by zinc dust held in a Hooch crucible and determination with a standard solution of sulphocyanate.9 5. Electrolysis.10 6. Colorimetry.11

Jan 2, 1915

By Jom Gentry

Acrylamide chemical grout (C3H2NO) has been successfully used for over 50 years to control groundwater and stop infiltration. This paper will address three unique projects involving the control of groundwater with each study providing special circumstances and geological conditions: encapsulation of radioactive hazardous waste in the United States, a tailings dam for a large copper/gold mine in Argentina and 27 miles of leaking subway in Canada. The primary reasons for selecting acrylamide grout were based on the following characteristics: thinnest chemical grout on the market, a true solution grout which contains no suspended solids in the blended product, flexible gel set times, and a 362 year half-life in soil as determined by the U.S. Department of Energy.

Continuous improvement in environmental management assists in the achievement of sustainability goals for the mining and processing of minerals. The use of regular internal environmental audits (scored or unscored) which form an integral component of an Environmental Management System (EMS), provide demonstrable evidence of this improvement. The audits described in this paper involve working with site personnel to develop and implement major improvement projects, providing advice on how to improve environmental practices and facilities, and disseminating innovative ideas and practices across the site and to other operations within the same group. Essentially the lead auditor assumes the role of a æskills coachÆ as opposed to a æpolicemanÆ, which is quite often the case for many audits. The audit process has been developed from involvement with a number of major coal mines in the Hunter Valley, where regular internal environmental audits have been undertaken every two to three months, over periods varying from 18 months to five years and more recently, with a metalliferous mine in the Northern Territory. Examples of the benefits of improved environmental performance (driven by the audit process) to sustainable development are provided. The auditing process as described is applicable to metalliferous mines, the processing of mineral ores, coal mines, coal handling and preparation plants, quarries, and oil and gas projects.

Jan 1, 2004

By J. R. Long, A. H. Roberson, T. R. Graham, R. S. Dean

EXPERIMENTAL work on the properties of high-purity alloys of the copper-manganese-zinc system has necessarily required extensive metallographic work to determine the equilibrium conditions in this system. Previous work on these alloys is fragmentary and, unfortunately, based on alloys made with impure grades of manganese, thus introducing significant amounts of iron, silicon, aluminum and carbon. Since these elements are known to affect equilibrium conditions, it became desirable to re-examine these alloys made from the pure metals. The alpha solid solution field was of particular interest and, therefore, was chosen for the initial work, which was outlined to determine the composition limits of this field. PREVIOUS WORK Heusler1 conducted an extensive survey of the liquid-solid regions of this system and also made an estimate of the solid-phase boundaries at 340°C. The pertinent part of his diagram is given in Fig. I, but it is of limited usefulness, since it applied to a single temperature only and is based on impure alloys under admittedly nonequilibrium conditions. Bauer and Hansen,2 likewise working with impure alloys, have determined the phase boundaries for alphabeta brasses containing small amounts of manganese and indicate an increase in the extent of the alpha field with increasing manganese. This is not in accordance with Heusler or with data obtained on pure alloys.3 They also described a third constituent precipitating in the alpha plus beta field below 350° to 400°C. but did not identify this constituent. Guillet4 and Heike and Ledibur5 have also noted this precipitate Each of these investigators recognized that impurities present in the manganese could and did have an effect on the structure and properties of their alloys. Corson6 in particular pointed out the hardening effects of silicon, aluminum, and carbon in copper-manganese alloys and Heusler reported that his alloys containing more than 25 per cent manganese were extremely brittle. In all probability this brittleness was due to the impurities present. This early work, therefore, should be taken as a general guide for preliminary studies only, and high-purity alloys may be expected to produce different results. The work of the Bureau of Mines laboratories with electrolytic manganese has been briefly summarized by Dean7 but includes only a short section on this system. Later work3 outlined a limited portion of the alpha field in the neighborhood of 65 per cent copper, 10 per cent manganese, and 25 per cent zinc. The present work was under-

Jan 1, 1945

By Dickin FJ

Advances in the development and application of in situ imaging of mineral processing operations using electrical tomography techniques are reviewed and illustrated with case studies relating to pneumatic conveying, mixing and centrifugal separation processes. The potential for applying these methods to full three-dimensional visualisation of the dynamic behaviour of flow in pipelines and separators, and the resulting consequences for process-modelling strategies, are discussed.

Jan 1, 1993

By William E. Dennis

"At the request of Philip S. Hoyt, the Eagle Mountain fluorspar deposits in section 35, block 68, Texas & Pacific Railroad Survey No. 9, were examined by an engineer3/ of the Bureau of Mines during March 1943: As a result of this examination; a preliminary program of trenching, sampling and core drilling by the Bureau of Mines was begun in. June 1943.4/ Eight deposits were explored.The Federal Geological Survey mapped the properties and furnished geologic information throughout the program, while the Texas .Bureau of Economic Geology6/ made preliminary maps that facilitated planning the exploratory work on section 35.The eight deposits explored by the Bureau of Mines are in block 68, Texas & Pacific Railroad Survey No. 9, Hudspeth County, Tex., approximately 7-1/2 miles south of. Hot Wells and 12-1/2 miles south of Allamoore, which is 10 miles west of Van Horn and 20 miles east of Gierra Blanco on U. S. Highway 80(fig. 1). A graded gravel road, built by the Public Roads Administration, leads from Hot Wells to the deposits in section 35, and there are unimproved roads, passable,by automobile, to all the other deposits.Carload shipments can be made to and from Hot Wells on the Southern Pacific Railroad, and complete railroad facilities are available at Allamoore on the Texas & Pacific Railroad.Van Horn and Sierra Blanca are the only local source of labor and. supplies. The prevailing wage for common labor is 60 cents an hour. Living accommodations are obtainable in Horn and Sierra Blanca.No electric power lines pass near the deposits. Diesel and gasoline motors are employed to furnish power for mining and milling operations.Two recently 'drilled water wells on section 35 furnish water for the mill. Other wells will be drilled if the present supply is inadequate for prolonged Peak operation.The properties lie in the foothills on the northeast side of the Eagle Mountains at 5,500 feet altitude. The Eagle Mountain Range rises sharply from a broad, flat valley known as Eagle Flat. Eagle Peak, the highest in the range, has an altitude of 7,510 feet. In the vicinity of the fluorspar deposits the topography is moderately reliefs ranging from 50 to 300 feet."

Jun 1, 1946

The Queensland Magnesia Project is based on a unique cryptocrystalline nodular magnesite orebody which required an innovative approach to process design in order to economically exploit the characteristics of the ore and produce a marketable range of high quality refractory magnesias for a declining world market. High quality natural refractory magnesia must have an MgO content in excess of 95 per cent with a very strictly controlled content and ratio of residual impurities such as calcium, silica and iron. The natural products compete with magnesias derived by chemical extraction from sea water or brines which exhibit very high purity but often lack other characteristics which are of value to refractory brick makers. Since start up in late-1991 QMAG has achieved a remarkable market penetration for both its deadburned and electrofused products with sales for the 1993/94 financial year representing 92 per cent of deadburned capacity and 138 per cent of original electrofused capacity respectively, all at a time when the world steel industry has been in recession.

Jan 1, 1995

In 2006, a total of 7,178 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 ? Sand and gravel mines were the largest mining sector, comprising 48.2% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Sep 1, 2008

By P. Coghill, P. Revell

"Geo-sensing is the ability to routinely measure or infer rock properties at a range of scales using non-destructive scanning devices. These devices can provide information and data flows to support integrated decision making across the minerals value chain. Geo-sensing has been used for many years in minerals exploration using technologies such as satellite imaging and airborne geophysics but to date the use of sensing technologies in between the mine and mill has been very limited. The aim of this research is to develop new mineral sensing technologies that can enable grade engineered ore streams through the rejection of low value gangue or deleterious elements either in the pit or during transfer to the mill. This paper focusses on the research and development being carried out by the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and its associated members on new sensing technologies. At the start of their development these technologies were classified on the Technology Readiness Level scale at 3 (TRL3), equivalent to a proof of concept. Laboratory testing and design is aimed at progressing these sensing technologies to TRL5 which is ready for testing at an end users site. New data obtained during the laboratory testing and design phases are presented in the paper demonstrating performance specifications such as detection limits and measurement speed which can be used to infer the pod size of gangue that can be rejected at scale. Grade Engineering® and coarse gangue rejection are considered as key drivers for the mining industry to address the higher mining, processing and environmental costs associated with ore bodies with declining grades. This is an industry wide problem and the development of mineral sensors is seen as key enabling technologies for Grade Engineering® and coarse gangue rejection. The technologies presented in this paper enhance value through early decision making of ore quality and improve the overall resource value case through improved grade and throughput engineering."

Jan 1, 2018

By William G. Davenport, Eric H. Partelpoeg

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important advantages of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate; (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elimination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the threshold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step smelting is still a process of the future. The paper describes in detail the potential advantages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985

By R. L. Caldwell, E. E. Glenn, L. J. Norton, A. J. D. Straus, S. V. Holcomb, J. Zemanek

A new and unique logging tool, called the Borehole Televiewer (BHTV), has been developed to inspect boreholes and to evaluate formations. Even though geologists and engineers have had only about 3 years' experience with the BHTV, the thinking of many of them has been radically influenced by the fascinating and revealing "log-picture" recorded with the tool. The BHTV fills a need for a logging tool that can produce a direct and descriptive record of the physical properties of the borehole environment. Although primarily developed to evaluate fractured reservoirs, the BHTV has been used successfully to solve a variety of problems related to formation evaluation and borehole inspection. Geologists and petroleum engineers have been confounded for many years by the problems of locating and evaluating fractures. Interpretation of the usual resistivity, acoustic or radioactivity logs, as well as the analysis of cores, for evaluation of fractured reservoirs is extremely difficult and often not definitive. This is understandable since analysis of cores from fractured formations has reported variously: (a) low porosity, (b) no effective permeability, (c) lack of any matrix oil saturation and (d) oil stains on fracture planes as the only indications of potential production.14 In recent years acoustic amplitude logs have been introduced and used with varying degrees of success to locate fractures.8'9'11"13 Conventional amplitude logs at best give only qualitative answers where quantitative ones are desired. The logs reveal nothing of the orientation of the fractures. In addition to these logs, various types of cameras, television, and rubber impression packers have been used for borehole inspection. (See Appendix.) The BHTV logging tool supplies both the quantitative and the orientation answers about fractures. The borehole can be filled with any homogeneous, gas-free liquid such as fresh water, saturated brine, crude oil or drilling muds. This tool takes an "acoustic picture" of the borehole wall. The resulting log is a representation of the borehole wall as if it were split vertically and laid flat. The log is oriented with respect to magnetic north. Any physical changes in the borehole wall are seen as changes in picture intensity. In this way, fractures, deformation or pits are reflected on the log. Tool Description The fundamental parts of the BHTV are shown in Fig. 1. A piezoelectric transducer probes the borehole wall with bursts of acoustic energy. A flux-gate magnetometer senses the earth's magnetic field and provides the means for determining the orientation of the log. A motor rotates the transducer and mag-

Jan 1, 1970

Papers in Classes A-Metal Mining, B-Milling and Concentration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Papers in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. Papers in Class G-Petroleum Division are distributed in PETROLEUM TECHNOLOGY, which is issued every other month. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J--Mineral Industry Education Division, K¬-Mining Administration, and 1-Geophysics, are issued as separate pamphlets. Contributions are papers that when printed or mimeographed are available but only on request.

Jan 1, 1944

By Raúl Prebisch

Continuando con el análisis de la realidad latinoamericana, el presente texto señala los factores estructurales internos de la insuficiencia dinámica de desarrollo latinoamericano como la absorción productiva de mano de obra, el aumento de productividad y necesidad de nuevas inversiones, los motivos principales de la insuficiencia dinámica, acumulación de capital, el obstáculo de la tierra, el funcionamiento de la estructura social, la inflación y la estructura social, los tipos de capital extranjero y la planificación y funcionamiento del sistema económico.

May 1, 1964

By Gordon E. Agar

"The effectiveness of two this compounds for copper sulphide depression in molybdenite flotation has been examined with batch bench scale tests.Both thioglycollate and trithiocarbonate proved to be good depressants producing results similar to those f or cyanide and hydrosulphide. Ferrocyanide was ineffective on the samplematerial tested.The depressing effect of thioglycollate was readily reversed by an addition of xanthate.IntroductionThe separation of molybdenite from copper sulphide minerals has been practised for a long time(1,2). The predominant scheme is to depress the copper sulphides while capitalizing on the ready floatability of molybdenite to effect the separation. There are many recipes for depressing the copper minerals(3), among them the addition of sodium cyanide, particularly if the copper is present primarily as chalcopyrite; some form of sulphide whether as sodium sulphide, sodium hydrosulphide or phosphorous pentasulphide when there is a mixture of copper sulphides such as bornite, chalcocite and chalcopyrite; potassium ferro cyanide may be used when chalcocite is the principal copper sulphide; peroxide or hypochlorite; as well as heating in the presence of lime. There are different mechanisms by which these reagent s depress the copper sulphides. Sodium cyanide and the sulphide-producing compounds apparently reduce the potential of the copper sulphides to the point where they ar e rendered unfloatable by xanthates . Another study(4) showed that after cyanide addition, chalcopyrite was rendered un floatabl e until the REDOX potential (measured with a gold electrode with a saturated calomel reference) had become more positive than -250 mY. If the chalcopyrite pulp was conditioned after the cyanide addition the REDOX potential increased slowly, whereas if air was introduced during the conditioning the potential r ose much more rapidly. The difference in time to reach the desired level of - 250 mV was as much as 20 minutes' 25 minutes being required when air was absent but less than 5 minutes when air was admitted . These observation s demonstrate some of the problems encountered when using cyanide to depress sulphides such as chalcopyrite . The system adjusts to counteract the depressing effect of the additive. To overcome this tendency it is necessary to either add an overdose at the beginning or to more or less continuously add the regulating reagent. In this study cyanide solution was added under automatic control to maintain a specified REDOX potential."

Jan 1, 1984

By R. L. Virta

Four companies mined ball call in four states in 2009, H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Kentucky-Tennessee Clay Co. (owned by Imerys Group), Old Hickory Clay Co. and Unimin Corp. Production, on the basis of preliminary data, was 820 kt (904,000 st) with an estimated value of $39.4 million. That was a 15-percent decrease in tonnage from 967 Mt (1.1 mil-lion st) with a value of $44.3 million that was produced in 2008. Tennessee was the top producing state with 59 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 71 percent of production was airfloat, 18 perc

Jun 1, 2010

By Wayne Trudel, Eric Saderhold, Lloyd McEvers, Lori Clarke, Charles Lynn Bolin, Leroy Schutz

Editor’s note: This is the second part of a two-part series on how mine geologists added about 141t (4.53 million oz) at Newmont Mining’s gold operations in Nevada during 2003. Part one (ME, July2004, pp. 19-26) showed how cross-functional teamwork among mine geologists, engineers, metallurgists and operators added $65 million in revenues at Newmont’s Gold Quarry Mine. Part two deals with how this same cross-functional team added about 25.8 t (830,000 oz) of gold reserves and two years of life at the company’s LoneTree Mine. This was done through improved reconciliation methods, pit optimization designs and updated geotechnical parameters. Part two also discusses how Newmont’s Nevada mine personnel added about 62.2 t (2 million oz) of gold reserves at its Twin Creeks Mine, extending the mine’s life by several years. The Lone Tree Mine is a sediment-hosted, micron gold deposit. It is dominantly situated in the Golconda thrust footwall. The north-south trending Wayne Zone fault controls the highest-grade ores and

Jan 1, 2004