Search Documents

By F. P. Haver, M. M. Wong

When a mixture of chalcopyrite concentrate and lime is heated in air, the following reaction takes place: 2CuFeS2 + 4Ca (OH)2 + 8 ½ 02 ; 2Cu0 + Fe203 + 4CaS04 + 4H20. Ca (OH)2 is the only common reagent that will adequately control SO2 evolution in roasting. Other additives tried, including CaO, CaCO3, Na2CO3, NaOH, MgO, Mg (OH)2, and MgCO3, were not effective. All reacted with sulfur, but not to the extent that will be required to meet the new control regulations for sulfur oxide emissions. For example: when the concentrate was heated with the theoretical amount of limestone (CaCO3), about 55% of the sulfur was retained in the calcine; whereas use of the stoichiometric amount of Ca (OH), converted approximately 99% of the sulfur to CaSO1. In most of the experiments, Ca(OH)2 was formed by adding CaO to concentrates containing enough water to simulate filter cake from flotation circuit. This eliminated the need for drying the concentrate and utilized the heat of hydration of CaO.

Jan 6, 1972

By P. R. Miles, J. K. H. Ma, J. Y. C. Ma, L. Bowman

"The bisbenzylisoquinoline alkaloids are compounds which can be isolated from plants and which exhibit a broad range of pharmacological activities. Perhaps the best known alkaloid of this group is tetrandrine (TT), a compound isolated from the root of a traditional Chinese medicinal herb, Stephania tetrandra. It has been tested for its effects on the cardiovascular system, tumors, and the lungs. For example, tetrandrine has been shown to act as a calcium entry blocker in cardiac sarcolemmal vesicles (King et a/., 1988) and has been used in China as a treatment for angina and hypertension. Its possible effects as a tumor-inhibitory substance have also been investigated (Kupchan and Atland, 1973). In addition, there are several lines of evidence to suggest that it is a possible therapeutic agent for the treatment of silicosis. Yu et a/. (1983) have shown that TT inhibits the development of experimental silicosis in rats when it is administered orally after intratracheal instillation of quartz. Other studies have shown that the alkaloid inhibits the synthesis of collagen by fibroblasts and the formation of silicotic nodules in rats exposed to silica (Huang et al., 1981; Liu et al., 1983). In fact, tetrandrine has been used clinically in China as an antifibrotic agent and has been shown to improve both the appearance of chest radiographs and the measurements of diffusing capacity in patients with silicosis (Li et al., 1981).Since tetrandrine may have a potential use as a therapeutic agent for fibrotic lung diseases, its effects on various pulmonary cells and tissues should be studied. Alveolar type II cells are located in the alveolar regions of the lungs and are important because they are responsible for the synthesis and secretion of pulmonary surfactant (Dobbs et al., 1982; King, 1984), regeneration of the alveolar epithelium after lung injury (Kauffman et al., 1974), and metabolism of foreign compounds (Bend et al., 1985). Furthermore, in silicosis, for which TT has been suggested as a treatment, there are increased amounts of pulmonary surfactant produced (Dethloff et al., 1986a,b) as a result of increased rates of surfactant synthesis by type II cells (Dethloff et a/., 1989; Miller et al., 1988). Because type II cells play a critical role in maintaining normal lung function and because type II cells are affected in silicosis, for which 'TT has been used as a treatment, we studied the effects of tetrandrine on energy metabolism in these cells in vitro. Energy metabolism was chosen because it is a basic cellular function which is neces-sary for other cellular processes to occur. Since type II cells depend on mitochondrial metabolism for energy production (Fisher et al., 1980), we examined the effects of tetrandrine on cellular and mitochondrial ATP production and oxygen consumption. Additional experiments were performed in an effort to determine if intracellular calcium levels may be involved in the TT-induced effects. A preliminary report of those results has appeared previously (Ma et al., 1991)."

Nov 1, 1995

By Edward G. Cunney

Track in underground bituminous coal mines was investigated, and technology was taken from other industries in order to obtain information on conditions that impair the safety and efficiency of the track and to develop guidelines and useful information on the construction, inspection and maintenance of mine track. Volume 1 contains information on the investigations, observed track conditions, useful technology from railroads and other industries, derivations of track condition descriptors and recommended limits, conclusions, and recommendations. Volume 2, Guidelines, contains recommended standards and practices for mine track. It includes the relation of track conditions to safe speeds; descriptions and limits for measurable track features such as gage; descriptions of conditions for track components that are normally not measurable, such as subbase soils; construction requirements and techniques, inspection requirements and methods; and methods for managing and performing track maintenance work. As a research product, it does not repeat the summary or derivations. Volume 3, Inspection Handbook, summarizes recommended standards and procedures from Volume 2 and provides related information for' ready reference by inspectors in the mines. As a research product to be used in mines, it does not repeat the summary, derivations or references.

Jan 1, 1977

Jan 1, 1928

By Kosta Fytas, Nour-Eddine Chaouai

"Selection of the appropriate kriging plan during indicator kriging estimations is of a paramount importance to the precision of ore reserve estimation. However, very little is known on the sensitivy of indicator kriging results when changing the kriging plan parameters (mainly search distance and number of samples). This paper evaluates the effect of the search distance and number of samples on indicator kriging results using a gold deposit as a case study.IntroductionBlock estimation using kriging is based on the autocorrelation function (variogram) on one hand and on the kriging plan on the other. As far as the variogram is concerned it is more or less subjectively adjusted and this is reflected on its parameters (range, sill, nugget effect and anisotropy). The effect of a poor estimation of these parameters on the kriging variance of ordinary kriging has been proven very important (Brooker, 1986). Choosing a kriging plan is generally a difficult matter depending on the estimation type (global or local). Generally there is not a unique kriging plan be cause there is not a unique structural analysis (variogram). There are no rules or dogmas in choosing a kriging plan but it is rather a function of the sampling pattern (David, 1982).Structural analysis requires the hypothesis of quasistationarity but very often either the data available within the zone of quasi-stationarity are too many so that the search distance is reduced during kriging or the data are too few to satisfy a stationary kriging system (Journel and Huijbregts 1978). As a rule, the larger the neighbourhood, the more precise the estimates should be , but for large neighbourhoods the hypothesis of stationarity does not always hold (Rivoirard 1987; Armstrong and Champigny 1989)."

Jan 1, 1991

By H. M. Rutherford

THE reflection method in seismic prospecting has aroused much interest in the past few years. The purpose of the present paper is .to present the method of reflections in the mapping of geologic structure and also to give some indication of its limitations. The reflection method is well adapted to the mapping of geologic structure in the Mid-Continent fields, and has been found most useful there. The refraction method is ideally suited to the finding of structures, such as domes, where the amount of relief is very large. This explains the brilliant success of the refraction method in the Gulf Coastal region of Texas and Louisiana. The additional fact that salt has a much higher velocity than the sur-rounding sediments made their discovery much easier. By the use of the reflection method, differences of relief of 25 to 50 ft. to the mile may be detected at a depth of 5000 ft., and the depth points accurately plotted on a map. This is hardly possible by the use of the refraction method. The reflection method has been in almost continuous use in the Mid-Continent area since 1926, but very little, if anything, has been published until recently(7) ? regarding either the method or the results. The dis-covery of several oil fields is now attributed to the use of the reflec-tion method. Reflection methods have been used by the Germans to find the thick-ness of the ice of several glaciers. (2,8) The depths there considered were of the order of only a few hundred feet. For the method to be of any practical value in this country, it must be able to work to depths of several thousand feet. As was indicated above, this is now possible, though there are many problems connected with the reflection method yet to be solved. The refraction method requires that the shooting be done over long ranges. It was necessary, for example, to take distances out to several miles in order to penetrate some five thousand feet. Naturally this uses a good deal of dynamite. In the reflection method the distances are much shorter and the amounts of dynamite are much smaller, within limits which will be noted below. The chief distinction between refrac-tion and reflection methods is to be found in the analysis of the seismo-gram. Refraction shooting makes use of only the first arrival of energy

Jan 1, 1932

By Schofield D, Denby B, Stout F, Moli A

This paper documents the development of a user-friendly computational program, which has been constructed to assist the mine ventilation engineer in the optimal design and operation of methane drainage ranges. In the past, many computer tools for ventilation engineers led to the development of `research systems'. These computer systems, although developed with the needs of the industry in mind were due to a combination of inexperienced programming methods and the availability of suitable user interface software not easily accessible to the practising engineer. Recent developments in computer hardware and software (particularly windows based graphical user interfaces) mean that engineers no longer need to dedicate large amounts of valuable time to become familiar with often complex items of software. The authors of this paper intend to demonstrate a practical system which successfully integrates complex mathematical models, an easy to use interface and knowledge based techniques. The graphical interface guides the user to draw on the screen a mimic diagram representation of the methane drainage network. The user is prompted, during the construction of the drawing, to input the information and data required by the calculation and knowledge based procedures. The computer program then calculates all of the flows, purities and pressures throughout the network. Given reliable measured data from an existing range a comparative analysis can be performed between the predicted and measured network flow data. A knowledge-based system may utilise this analysis to either update the operational status of the network or suggest either a reasoned maintenance or remedial strategy to improve the performance of the drainage system. The development of the OMEN project has been carried out at the request of the Midlands Group, British Coal Corporation, Edwinstowe. The system is about to be field tested at a number of mines. It is hoped that when this paper is presented that the system will be used at both Group and mine level.

Jan 1, 1995

By J. E. Gebhardt

Progress is reported on capturing the effects of gangue chemistry in the context of a comprehensive stockpile heap leach model for leaching copper sulfide ores, employing leading edge computational fluid dynamics (CFD) technology. The stockpile is a complex multi-phase process, comprising of a solid porous media, with complex fluid flow, gas and liquid phases, competing solid-liquid reactions, dissolution of minerals and transport through the heap. The model accounts for many of the challenging physical and chemical features of the heap, including transport and reactions kinetics for the important copper and iron sulfide minerals, ferrous oxidation, bacterial effects, thermal energy, acid and sulfate balances. In this contribution, the model has been extended to incorporate dissolution of various species from gangue reactions and precipitation of hydronium and potassium jarosite, ferric hydroxide, alunite, and gypsum. The effect of aeration on the simulation of a copper sulfide heap leach is provided as an example.

Sep 1, 2012

By V. B. Achanti

Reliability of the compressive strength of a coal seam determined in the laboratory is often subjected to debate. Effects of the coal seam's inherent characteristics, specimen preparation, testing procedure, testing condition, and a number of tests often result in drastic variation of the strength data. This paper deals with the development of a testing procedure for determination of coal seam compressive strength in the laboratory. Coal samples from two different coal seams were tested. First, the inherent characteristics of each coal seam such as coal structure, Hardgrove Orindability Index (HOI), Slake Durability Index, proximate analysis, and mechanical properties namely Young's modulus and Poisson's ratio were determined to categorize them in terms of their characteristic severity liable to produce variable strength data in typical laboratory tests. Second, two commonly used laboratory specimen shapes namely; cylindrical and cubical, were tested to determine which shape produced the least variation of data and reproducible strength values. Third, four loading rates within the static testing range (Le. 0.007 MPa/s (1.0 psi/sec), 0.07 MPa/s (10 psi/sec), 0.34 MPa/s (50 psi/sec), and 0.7 MPa/s (100 psi/sec)) were used to determine an ideal loading rate. Finally, the number of test samples required to produce strength data within the acceptable standard deviation, considering coal seam characteristics were established.

Jan 1, 1996

By Roland W. Merwin

The Bureau of Mines has studied the possibility of using the heap leaching process for treating the gold ores in the sedimentary beds of northeastern Nevada. This paper summarizes all available information on the technical and economic feasibility of heap leaching oxidized ores from these beds, past industry application of vat leaching, results of recent Bureau of Mines and industry tests on heap leaching ores from this region, and requirements for planning the proper application of heap leaching. Preliminary tests on representative samples of ores from the region show that a satisfactory recovery of gold can be obtained by heap leaching the ores with cyanide at a relatively coarse size. Significant deposits of gold ore occur in sedimentary beds of various locations over an extended area 40 miles wide and 200 miles long in northeastern Nevada. The area is centered 40 miles west of and runs parallel to the leading edge of the Roberts Mountain thrust fault system, a prominent geologic feature in the area. The general locations of past and present gold mining operations are shown in figure 1. (slide 1)

Jan 1, 1969

By J. Marshall Downey

The most fortunately situated U. S. potash producer-whether in New Mexico, California, or Utah--once simply took from the ground a mixture of sodium chloride and potassium chloride, crushed it to a maximum of 10 mesh, and separated the two salts by physical methods. He piled the sodium chloride on the desert and sold the potassium chloride to fertilizer mixing companies. Seven companies in the Carlsbad basin of New Mexico now use at least three basic processes for making the separation and at least three more processes have been or are under investigation. In addition, two companies outside the basin use two methods for taking KC1 from natural brines

Jan 12, 1958

By G. R. Moulder

A device was developed that measures dynamic stress (ultrasonic energy) transfer through installed rock bolts, a measure that is directly proportional to the degree of grout bonding of the bolt to the mine roof structure and thus the ability of the bolt to bear static stress. The rock bolt bond tester (RBBT) is a hand-held portable device that shows three ranges of bolt bond condition; i.e., one-third (Bad bond), two-thirds (marginal), or fully bonded. These are shown respectively by a red, yellow, or green light that displays for 4 s. RBBT performance was verified with 2 1/2-to 8-ft bolts installed in various types 0f mine roof structures (sands tone, shale, and boney coal-mud), and 15 now being tested by the Bureau of Mines in mines across the United States. The unit is about the size of a five-battery flashlight and contains the transducer electronics, and battery pack. The RBBT is designed for extreme ease of operation, requiring only manual contact with the bolt and signal read-out. The batteries are rechargeable and the package is designed for durability in a mine environment.

Jan 1, 1983

Coaxial cable structures form the subject of substantial theoretical and experimental investigations either directly related, or which can be extrapolated, to the communications needs and environments of U.S. coal mines. Communication systems based on "guided" waves, of which "leaky" coaxial cables are one implementation, are attractive candidates for providing a range of communication functions primarily along haulage ways, and possible also within sections up to the working face. (However, there are still strong reservations as to whether a practical coaxial cable sys tem could provide sufficient communications coverage within a section. ) In this Part, we present the results of some theoretical calculations of the performance of leaky coaxial cable communication systems. We also analyze the applicability of the theoretical and experimental results obtained by other researchers to the needs of U.S. coal mines. In particular, this investigation has been focused on the utility of relatively low cost, conventional, flexible, coaxial cable at frequencies covering the LF through HF bands and extending into the lower part of the VHF band, as opposed to relatively high cost, special semi-rigid, coaxial cable* at frequencies in the VHF and UHF bands. There are three major design alternatives for coaxial cable communication systems considered in this chapter: • Base station feeding a coaxial cable with high surface transfer impedance (holes in outer conductor, e.g., braid construction). • Base station feeding a coaxial cable with repeaters (U.K. experiments). • No base station, direct communication via a coaxial cable with periodic radiative structures.

Jan 1, 1974

By Irving Hauser

The determination of new ways to cut costs in then times of economic uncertainty is essential in running a successful business. Arco Petroleum Products Company a Division of Atlantic Richfield Company recognized an opportunity for a substantial cast savings in transporting calcined petroleum coke to market by simply building an economical port facility at a location that would enable them to drastically cut their normal rail haulage distance.

Jan 1, 1982

By W. R. Hail

A proactive design and construct approach was used to remediate the Warm Springs Ponds Complex near Anaconda, Montana under "Superfund". The pond complex is used for treatment/settlement of heavy metals and is a repository for 19,000,000 cubic yards of tailings, precipitates and associated sediments. Remediation has resulted in treatment/settling capacity for flows up to the 100-year flood (3,300 cfs); expansion from 5 to 11 ponds in series requiring 12.5 miles of new or improved embankments with associated hydraulic structures; flood protection for the 0.5 Probable Maximum -Flood (PMF) (70,000 cfs); and closure of exposed tailings along with aquatic and terrestrial habitat enhancement.

Jan 1, 1995

By M. E. Charles

The use of water flowing as a lower layer to reduce pressure gradients in petroleum pipelines was investigated using 17.5 deg. A.P.I. Lloydminster crude oil in a 1-inch laboratory pipe-line and a 21h-inch field pipeline. The method was found to be very effective in reducing the pressure gradient below that for the oil flowing alone. The factor by which the pres-sure gradient was reduced varied with the percentage of water added, and in general exceeded 10 for water contents ranging from 40 to 60 per cent. Within this range of water content the pressure gradient reduction factor was independent of the oil flow rate.

Jan 1, 1960

Strategic Branding ? In 2006 Explore for More was created ? By industry, for industry ? Cohesive approach to career attraction ? Defines industry and employers of choice Career Kits ? Positive impression of mining: ? before seeing the brochure 31% ? after seeing the brochure 83% ? Likely to consider a career in mining: ? before seeing the brochure 12% ? after seeing the brochure 23% MARS ? Mining Attraction, Recruitment, and Retention Strategy (2007-2010) ? Attract, recruit and retain a skilled workforce ? Increase participation of under-represented groups ? Dispel myths and misconceptions of the mining industry ? Inform and educate Canadians of career opportunities ? Promote and build upon industry best practices in workforce planning

May 1, 2009

By R. V. Ramani

This report is volume 10 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Ventilation subsystem of the Master Design Simulator. The Ventilation subsystem has the capabilities to handle: (1) branches in parallel or series, (2) fans in parallel or series, (3) multiple fans, (4) methane, compressed air, or other injections into the system, (5) leakages and fixed quantities, and (6) calculations of absolute pressure at nodes. The program uses the Kirchoff's Junction and mesh laws, and the Hardy-Cross iterative technique to converge to the desired accuracy in solving fox the head quantity. A case study is included in the report illustrating the use of the model. The appendices of the report constitute a user's manual for the Ventilation subsystem, and include a program listing.

Jan 1, 1975

Jurist, educator and historian Neil Reynolds will be the keynote speaker at the National Mining Hall of Fame's 11th annual induction banquet on Sunday, Oct. 11,1998 at the Pointe Hilton Resort in Phoenix, AZ. Reynolds is Municipal Court Judge for the City of Leadville, CO, home of the National Mining Hall of Fame & Museum, and a fifth-generation resident of the community. His family staked mining claims on nearby Mount Massive in 1862. Judge Reynolds is a fulltime faculty member at Colorado Mountain College, Chairman of the Lake County Historic Preservation Advisory Board and practices law in Leadville. In announcing the speaker, Board Chairman Richard Moolick said seven inductees into the National Mining Hall of Fame will join 138 mining greats previously honored in the annual ceremonies. This year's inductees will be enshrined by Thomas Falkie, president and chief executive officer of Berwind Natural Resources of Philadelphia, PA. Moolick also announced that Jeffrey Clevenger will be the master of ceremonies for the induction banquet. Clevenger is executive vice president of Cyprus Amax Minerals, Englewood, CO and president of Cyprus Climax Metals, Tempe, AZ. A cocktail reception at 6:30 p.m. will precede the black-tie (optional) dinner, to begin at 7:30 p.m. For additional information, contact Esther Mellott at 719 486 1229. Here are the biographies, then, of this year's seven inductees to the National Mining Hall of Fame & Museum.

Jan 1, 1998

By Paul M. Jr. Musgrove, Thomas D. Henderson, Mark B. Nesbitt

Introduction History. Vat leaching operations began in October 1953. Since that time, about 4.2 million tpy of oxide ore averaging 0.72% copper have been treated. Economic conditions, improved operating methods, and increased production facilities have allowed the ore grade to be reduced over the years. The average ore grade was 0.84% Cu during the 1950s, 0.68% in the 1960s, and was 0.50%, or below, during the 1970s. By 1961 some 35 million tons of oxide ore had been removed from the mine, exposing the underlying sulfide ore body. A 5,000¬ tpd concentrator was constructed and put into operation to treat the sulfide ore in November 1961.1 The original crushing plants were used for both oxide and sulfide ores, but by adding a third crushing shift, six days per week, the total ore treated was raised from 12,000¬17,000 tpd. Dwindling oxide ore reserves prompted expansion of the concen¬trator to 13,500 tpd in 19672 so that exhaustion of known reserves of both ores would occur at nearly the same time. Again, no additional crushing facilities were added during the expansion. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to about 9,000 tpd. Instead, the addition of two crushing shifts per week and improved operating procedures have increased the treatment rate to 26,500 tpd-13,000 tpd to the leaching plant and 13,500 tpd of sulfide ore treated in the concentrator. Geology. The Yerington ore body is a disseminated porphyry copper deposit where a quartz monzonite porphyry intrusive contains the major part of the ore values, with some copper mineralization found in the adjacent granodiorite and other rocks. The geology of the Yerington Mine was aptly described by J. R. Wilson (Mining Congress Journal, June 1963). The ore body is one of few porphyries where geologic conditions were optimum for the formation of an important concentration of oxidized ore with minimum economic effect of secondary enrichment. The principal mineral in the oxidized zone is chrysocolla, which irreg¬ularly occurs dispersed throughout the rock and as narrow seams along fissures. The grade of the ore in the oxidized zone is generally the same as in the primary sulfide below, although some massive concentrations do occur as vein-like fissures and as filling of breccia zones. Cuprite, tenorite, melaconite, malachite, and azurite occur but are not abundant. Lying between the chrysocolla horizon and the primary sulfide is a transition zone whose limits are irregular but seldom with vertical range exceeding 50 ft. Chalcocite, cuprite, melaconite, native copper, and chrysocolla occur superimposed on the primary sulfides. Chalcocite replacement of chalcopyrite, as well as secondary chalcocite, do occur. The primary sulfide minerals are chalcopyrite and pyrite, with minor amounts of bornite and covellite. There are no appreciable gold or silver values, and molybdenite has rarely been noted.

Jan 1, 1985