Search Documents

By H. Saroglou

Anisotropy is a characteristic of intact foliated metamorphic rocks (slates, gneisses, phyllites, schists). Testing was used to establish the anisotropic behaviour of selected gneissic rocks. The effect of anisotropy on various mechanical properties (strength, deformation) and dynamic properties (wave velocity) was examined. The rock samples were also tested at successively higher confining pressures in order to evaluate the effect of anisotropic behaviour at high overburden pressures.

Jan 1, 2004

By L. Su, S. Liu, K. Jiang, K. Xie

The reduction of iron dissolution and acid consumption is fairly important in the extraction of Ni and Co from laterite ores from both economic and efficiency perspectives. BGRIMM conducted detailed research to investigate the behavior of iron in a nickel laterite leaching process. The mineralogy of Ni and Co was studied. In limonite ore about 76% of nickel is present in goethite while in saprolite ore 79% of nickel is associated with magnesium and silicon minerals. Test work revealed that limonite can be decomposed completely with enough acid concentration during atmospheric leaching. More than 98% of Ni and Co were leached into solution while 85% of the iron was also dissolved with 130-140 g/L iron in solution. Iron precipitates as hematite in the temperature range 250-270?C without neutralization reagents. That’s why limonite is treated by high pressure acid leaching (HPAL) technology to achieve nickel extraction and iron precipitation in the same autoclave. BGRIMM’s test results indicated that the remaining acid in atmospheric leaching solution and acid released by iron precipitation at a lower temperature was enough to leach saprolite efficiently. The so-called inverse leaching technology leaches limonite at atmospheric condition and the leaching slurry combined with saprolite is pumped into an autoclave to leach saprolite at 150-170?C. In the autoclave iron precipitates as hematite without acid consumption. Total nickel and cobalt extractions in the test program were more than 90% with iron content in solution below 8 g/L. In this inverse process iron dissolves in the atmospheric leaching stage and precipitates as hematite in the low temperature leaching stage. Compared with HPAL the leaching temperature is reduced to 150-170 ºC from 250-270 ºC. Compared to atmospheric tank leaching acid consumption is reduced from 850-950 kg/t ore (atmospheric) to 550-650 kg/t ore (inverse).

Jan 1, 2016

By J. A. Finch, B. J. Huls

Accurate level detection is required to make full use of level in optimizing control strategies for flotation columns. Techniques based on pressure and electrical conductivity are compared. Pressure and conductivity profiles give good agreement on level. Level calculated from single and multiple pressure values became more accurate using, in order, one, two and three sensor locations. The level estimate remained in error, however, because, unlike the collection zone, froth zone bulk density varies with height. A conductivity probe continually updating the conductance profile is a practical method of obtaining an accurate level.

Jan 1, 1990

The optimum situation in sealing the soil with latex would be to locate the sealant at the depth where natural permeability is lowest, and to narrow distribution of the latex to a film. To ascertain how closely we were achieving these objectives it was necessary to devise a method to measure the concentration of latex in soil. A number of methods were explored and two were used in actual field tests. SBR latex tagged with c14 was prepared and used to determine the distribution of polymer in the soil. The latex was made by copolymerizing a mixture of radioactive and normal styrene with butadiene in bottles by conventional methods. Average particle size was 600 Å. Diluted aliquots had 1.40 microcuries radioactivity per gram of latex. Tagged latex was mixed with soil in a range of proportions from 0.01 to 0.25% by weight to develop a calibration curve. Analyses of soil in the laboratory and from the field were determined by comparison with this master curve. Styrene-containing polymers have a characteristic peak at 700 cm-1 but crosslinked SBR is not soluble in solvents normally used in infra-red spectroscopy, e.g., carbon disulfide. We developed a method for solubilizing the crosslinked polymer by stirring overnight at room temperature a soil sample in chloroform with t-butyl hydroperoxide and osmium tetroxide. The filtered chloroform residue was dried to constant weight, thoroughly mixed and pressed into a KBr pellet, and concentration was determined by measuring the absorption at 700 cm-1. Details are given in an Appendix.

Jan 1, 1972

By C Gunther

In deposits in which the secondary zones are well defined a layer of rich oxidized ore is frequently found immediately to overlie the enriched sulphides, from which it is derived by direct oxidation in place. In deposits that contain oxidizing precipitants particles and masses of residual oxidized ore are likely to be scattered through the leached zone, having been precipitated during migration before reaching the zone of enrichment. This precipitation hinders secondary enrichment and in extreme cases prevents the formation of such concentrations. Residual ores are precipitated by various reagents. Carbonates are formed through the action of the carbonic acid contained in surface waters, and also directly through the replacement of calcite, especially where the containing rock is limestone. Native metals, such as copper, gold, and silver, are formed by the action of reducing agents, among which organic matter and ferrous sulphate are prominent. Kaolin, gouge, and certain shales occasionally act as powerful precipitants through adsorption. Silver is often found as residual chloride, formed through precipitation by the chlorine contained in surface waters. Residual ores are often the result of incomplete solution, the relatively insoluble minerals being left behind during the migration of associated metals; incomplete oxidation and solution often leave residual masses of unaltered, or partly altered, sulphides in the oxidized zone. Such residual particles or masses have commonly been enriched by additions from circulating, metal-bearing solutions. During oxidation under conditions that permit reprecipitation, such as the oxidation of sulphide deposits in limestone, a scab

Jan 1, 1932

By Joel K. Witt

San Manuel Oxide operations of BHP Copper, located in Southeastern Arizona, operates a leach-solvent extraction/electrowinning (SXEW) facility that produces high quality cathode copper from low-grade oxide ores. Permanent heap leaching and in-situ leaching methods accomplish the dissolution of copper from the oxide ores. Open pit mining and heap leach construction took place from 1985 to 1995. Run-of-mine oxide ore from the pit was hauled to the heap dumps and leached by the soaking cure and continuous irrigation method. Solution application to the heaps still continues and acid soluble copper recovery has reached 86%. This paper presents and discusses the current operating practices and innovations applied to the leach facilities to maximize copper recovery from the heap leached residue. Factors such as irrigation methods, solution chemistry, sideslope treatment, post curing, lixiviant acid strength, and "rice paddies" irrigation, will be discussed. Heap leach solution control and sampling methodologies will be also presented.

Jan 1, 1999

By A. L. Engel

In the period of 1942-1945, medium-grade, oxidized, lead-silver ore was mined and shipped from the Diamond district near Eureka, Nev. An encouraging tonnage of low-grade ore was developed during these operations and partly blocked-out for future mining. If the low-grade ore could be treated profitably, further development of the district would result, and production of an important strategic metal might be increased. A representative sample of Diamond district ore was obtained through the Reno office of the Mining Division for the studies described in this report. The sample consisted of lumps and fines of a highly altered siliceous rock containing much earthy red hematite and some granular black hematite. Examination with the binocular microscope showed the lead carbonate mineral, cerussite, in seams and disseminated in the hematite. No zinc or silver minerals were identified, and no sulfide minerals were present. Analyses of the ore showed:

Jan 1, 1951

By R. H. Terhune

THE enormous production of pig-iron, together with the many difficult and interesting problems with which its manufacture is fraught, has secured to this industry the exclusive attention of scientists with reference to the chemistry of iron, while some of the minor departments of its metallurgy have suffered neglect. Particularly is

Jan 1, 1873

By Martin P. O'Connell

"IT IS INDEED A PRIVILEGE to address a group representing a sector of the Canadian economy so important as is the mining sector. Important, not only today, but certainly of great importance for the future development of Canada, for employment, for our trade balance and indeed, when one looks at what we are calling increasingly an industrial strategy, for the future. Surely mining will have a very significant role to play in fulfilling that. It's of special interest to me, as the Minister of Labour - and I ought to confess at the very beginning that I am just two months into this function - of special interest for me to know that you are giving such attention to labour-management relations. I think it is timely that, from my point of view at least, you do this, because for the first time in twenty four years major revisions of the Canada Labour Code as it relates to industrial relations and disputes settlements are currently in the House of Commons going through their second reading, after an easier introduction and some changes which I would be very pleased to describe later this morning. It is very timely too, I think, that we should be looking at this area because public interest is certainly at a high level. It is not only at a high level but it expresses a good deal of irritation with the current status and procedures and results in collective bargaining and there is some urgent search for more sophisticated or modified procedures for settling differences in labour-management relations. The public wants different kinds of results. I think that is apparent to all of us. They want results in terms of justice and equity on both sides. And it means that a Minister of Labour and certainly governments who often are representing, or are the third party in discussions, have a very important and complex role to play in attempting to create a balance as these two parties come to contracts and come to agreements."

Jan 1, 1972

Two Variable Real-Time Algorithm for Cone Crusher Control

Sep 13, 2010

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been 'designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

For too long we, as an industry, have borne the brunt of irrational claims, poor science and even worse, journalism with regards to our affect on the environment. To some of us, the overwhelming media attention on greenhouse warming, the polluting outputs of mineral processing or unthinkable depletion of natural resources has left us embarrassed and more unfortunately has turned bright young people away from a career in the minerals industry.This paper shows the hypocrisy associated with an element of the green movement and dispels some general myths on mining disseminated by radical environmentalists.The fallacy of the greenhouse warming effect will be scrutinised by common sense and the mining industryÆs use of land will be discussed and put in proper perspective.Problems associated with safety and emissions and the means to overcome such are discussed briefly.

Jan 1, 2004

By Andrew J. Brennan, Jonathan A. Knappett, Lewis Hamilton, Michael J. Brown

"Abstract This paper investigates the compressive behaviour of screw piles in sands and the key design parameters which control this. These types of foundation elements have typically been used as screw anchors onshore (i.e. for their tensile capacity), but there is increasing interest in their potential use as compression piles for supporting offshore marine renewable energy (MRE) devices (e.g. wind and tidal turbines) in deeper water. For such foundation applications, the compressive capacity is as important as the tensile capacity and is not well understood, particularly in cohesionless soils which are a likely seabed condition in MRE applications. A 1-g laboratory study was initially conducted on small scale model screw piles in sand beds of various relative density between 25 – 88%. These experiments were used to validate a Finite Element (FE) model having a stress-dependent constitutive model, making it useful for future up-scaling of the pile size for field applications. Following validation, the FE model was used to conduct a parametric study on the effects of flange spacing ratio (s/Dflange) and flange to shaft diameter ratio (Dflange/Dshaft). By using a validated FE model for this study, it was possible to observe the failure mechanisms (through the shear strain distribution) within the soil and correlate these with the pile capacity. This information was then used to comment on the most optimal (cost-effective) pile design for supporting compressive loads. This study represents a key step towards producing design tools appropriate for the design of screw piles in MREapplications.IntroductionAs defined in this paper, screw piles consist of a central small diameter hollow steel shaft, around which thin circular steel flanges run. Their principle of operation is that the flanges are spaced so as to trap the soil between them, thereby acting as an equivalent solid pile of the outer flange diameter, with a fully-rough ‘shaft’ interface (as shearing is soil-soil). One of the most important design decisions relates to the spacing of the flanges – if the flanges are spaced too far apart, then the soil will not be effectively trapped and the pile have a lower axial capacity and stiffness (controlled by the shaft friction along the central shaft and the bearing resistance arising from the individual flanges; If the flanges are spaced too close together, then there are potentially flanges which are not contributing to the pile capacity, therefore making the pile more expensive than it needs to be."

Jan 1, 2014

By Nixon TR

The Australian Coal Industry Research Laboratories Ltd. (A.C.I.R.L.) MINVENT computer program can be used to simulate existing and projected colliery ventilation requirements. New collieries can be planned using a database of ventilation parameters which were ascertain- ed by A.C.I.R.L. surveys at selected collieries in N.S.W. and Queensland. Several techniques are used in both the formulation of the database and in the evaluat- ion of a ventilation system, prior to analysis by the MINVENT program. The analysis of a ventilation system requires the measurement of air quantities, pressures and hence airway resistances. All resistances are calculated at standard air density of 1.205 kg/m3. Air densities are derived from barometric pressure and wet and dry bulb temperature readings. Airway frictional and shock losses, leakage through stoppings and overcasts, flow of air through regulators, face resistance and resistance of anomalous ventilation features are related to the typical Australian measured data presented.

Jan 1, 1983

By E. Burgos Cruz

The behaviour of S, N and P during refining of Fe-18 wt%Cr-10 wt%Ni with calcium carbide was investigated. The effects of the initial contents of C and N in the metal phase, as well as the supply method of calcium carbide to the melt on the removal degrees of S and P were evaluated. Heats were carried out at 1873K, in MgO crucibles, using a laboratory induction furnace. It was observed that simultaneously with S and P, N and O have also participated in the reactions. It seems that, in fact, O governs the behaviour of the other elements dissolved in the melt and that N is had to the removal of P with calcium carbide. It was also noticed that high C content in the metal phase have not altered the dephosphorization and desuffirization degrees, but that the supply of calcium carbide done by injection led to a lower dephosphorization degree than the one obtained by dumping it.

Jan 1, 1995

By G. S. Dobby

High-intensity wet magnetic separators have been successfully introduced into the mineral processing field over the past ten to fifteen years, due largely to rapid advancements in magnet design. Wet magnetic separation, until recent years, was applied solely to the concentration of minerals of high magnetic susceptibility, such as magnetite, at relatively coarse sizes. Now, however, high-intensity separators are capable of treating weakly paramagnetic minerals and have extended the range of treatable particle size down to about one micrometre(1,2). . One of the more recent-high-intensity separators developed is the Kolm¬Marston Marston type high-gradient magnetic separator (HGMS) (3,4) It consists basically of an iron-clad solenoid surrounding a matrix material - a fine, ferromagnetic steel wool or expanded metal lath. A schematic diagram of the device is shown in Figure 1. Large, highly localized, pertebations of the magnetic field are created by the ferromagnetic matrix. It is these field gradients that are instrumental in developing large magnetic forces which act on the mineral particles. Operation of the separator is simple. Slurried sample is fed through the matrix and, depending upon the mineral parameters of particle size and magnetic susceptibility and. the operating parameters of flow rate, field strength and feed weight, some particles will be attracted to and adhere to the magnetized matrix, while the others will flow through the matrix. The separation is completed by later removing the background magnetic field and flushing the captured mineral particles into a separate container. The process can also be applied on a continuous basis (S).

Jan 1, 1977

By L. D. Jaffe

IN previous metallographic work on titanium and its alloys, difficulty has been encountered in distinguishing spheroidal particles of titanium hydride, dispersed in a-titanium, from other phases that may be present, such as p-titanium. This problem is common in examination of commercial unalloyed titanium.' In the course of an investigation of the Ti-H phase diagram, it was noted that titanium hydride, dispersed in a matrix of a-titanium, showed strong optical anisotropy when examined under polarized light. With sensitive tint illumination, particles of the hydride, when the stage is rotated, changed from bright yellow to bright blue in color. Since P-titanium is cubic, it showed no color change on rotation, remaining dark gray or blue-gray. Although a-titanium is hexagonal, it showed only a minor color change, going from pale pinkish-blue to pale purplish-blue. These colors could be modified somewhat by adjustment of the illumination. They were observed in specimens mechanically polished, both without etching and after etching with hydrofluoric acid-nitric acid mixtures in either water or glycerine. The strong color change of the hydride seems to offer a simple method for its metallographic identification. Optical anisotropy of titanium hydride is inconsistent with its accepted face-centered-cubic structure.' Samples of iodide titanium containing 6 to 40 atomic pct deuterium were prepared for diffraction studies. After deuterating and slow cooling' the samples were held 21 % hr at 400 °C, water quenched, held 61 hr at 100°C and quenched, then held 64% hr at 255 C and quenched. Debye ex-posures with MoKa X-rays and 1.111A neutrons were made at room temperature of samples as-deuterated and after the 100" and 255°C treatments. Table I shows the lines observed, in addition to those attributable to a-titanium. These data show that the hydride phase was not cubic, but probably tetragonal. The titanium atoms appeared to form a body-centered-tetragonal lattice complex, two titanium atoms per cell, with approximate dimensions: a = 3.12A, c = 4.18A, and c/a =1.34A. This is equivalent to a face-centered-tetragonal complex, four titanium atoms per cell, with approximate dimensions: a = 4.42A, c = 4.18A, and c/a - 0.946A. The presence of the 2.98 and 1.81A neutron lines indicates that the true Bravais lattice is not identical with this lattice complex, but may be primitive tetragonal with dimensions some multiple of those of the complex. The relative intensities of the hydride and a-titanium X-ray lines as functions of overall composition indicated that the hydride, presumably in equilibrium with the a at 100" to 255"C, contained more than 62 atomic pct H. Acknowledgments The experimental work covered in this report was done at Brookhaven National Laboratory, through the courtesy of D. Gurinsky. The cooperation of J. Sadofsky, 0. Kammerer, A. McReynolds, and A. Cendrowski is gratefully acknowledged.

Jan 1, 1957

By H. E. Bartlett

Previously, the grade of ore at the shaft head was taken to be equivalent to the grade measured in the faces by means of chip sampling. The tonnage mined from the stopes is determined from survey volumetric measurements. Estimates of shaft head grade and tons include the grades and tons of waste, development ore, sweepings from old areas, and other sources, not all of which are sampled. The tonnage of ore delivered at the shaft is often estimated using skip factors. These factors are subject to manipulation and not all the skips are filled to the same level. Consequently, both the grade and tonnage of ore delivered at shaft head are subject to a measure of uncertainty. For many years, these uncertainties have led to disputes between shaft managers and metallurgists over the reconciliation between shaft tons and grade and plant tons and grade. These problems are compounded when several shafts feed a central processing plant. Shaft bonuses and a shaft?s profitability are affected by poor gold allocation methods. Without measurement of the grade and tonnage from all shafts, a poorly performing shaft could benefit at the expense of the other shafts. In order to improve the measurement of grades and tonnage at the shaft head, which is the custody transfer point between the mine and surface operations, South African mining companies have developed a methodology to measure the mass of ore from each shaft using rail weighing equipment, and the run-of-mine grades delivered from each shaft using cross-stream (go-belt) sampling. Harmony Gold Mining Company has implemented the rail weighing and go-belt sampling methods for their shafts. This paper deals with the statistical tests on the procedures and control measures that are in place to establish confidence in the gold allocations. The metal accounting system for examining the allocations follows the first principle of the AMIRA P754 Metal Accounting Code of Practice namely ?The metal accounting system must be based on accurate measurements of mass and metal content. It must be based on a full check-in check-out system?. The check-in is mass and grade of run-of-mine ore and the check-outs are the plant input grades and the recovery and residue from the plant. The balances between check-in and check-out are the subject of the statistical analyses, which have been conducted using the classical statistical tests and procedures that are generally used in all fields of endeavour. It is concluded that the gold allocation procedures that rely on go-belt sampling and rail weighing of ore from shafts has been successfully implemented, and that the system, which has been in operation at Harmony since 1993, has won general acceptance from stakeholders, with the gold allocations being perceived as being fair to all. Apart from the on-mine issues of bonuses and fair allocations, accurate metal accounting assists in the broader issues of generating accurate production figures for management. An added benefit of weighing and sampling ore at the shaft head has been that shafts now have daily moving average grades, which are used for grade control. The go-belt sample at the shaft head is the first accurate sample of production in the value chain from face sampling to gold bullion. Keywords metal accounting, go-belt sampling, run-of-mine sampling, codes of practice, AMIRA P754, train weighing, statistical analysis, gold split, allocation of gold, metal balance, grade control.

Jan 1, 2014

Operation of a pilot-scale Floatex density separator was studied using a pyrite concentrate slurry feed. Experimental measurements were further utilized in parameterization of a hindered settling simulation model. The model incorporates particle slip velocity calculation and also a separation efficiency function, adjusted to describe the feed material characteristics. The model was used to compute the overflow and underflow compositions when both fluidization bed pressure and teeter water flow rates were varied. In addition, prediction accuracy and the model validity were evaluated. The simulations gave good results when the teeter interstitial velocities were moderate enough to avoid excessive turbulence in the fluidization. Prediction of the cumulative overflow and underflow size distributions in most experiments yielded essentially less than 10% relative error between the sample data and the estimated value of the 50% passing sizes.

Jan 1, 2011

By Robert B. Parsons

"With several hoots of the whistle, Canada's fiscal engineers are once again cranking up the income tax locomotive, in an effort to inject new stimulus into a stubborn economy. And once again, additional gears, wheels, levers, and other mysterious part s are being added to the already complex machinery in order to accommodate the new push.This time, a significant new mechanism involves a major overhaul and expansion of the investment tax credit system.Although the shiny new devices have considerable appeal to a certain group of potential passengers, one wonders if all of the renewed chugging and huffing is on the right track.IntroductionAs indicated in Tax Notes in the July 1983 issue of CIM Bulletin , the April 19, 1983 federal bud get introduced a number of new measures which would permit investment tax credits and research and development deductions to "" flow through "" from a corporation to another taxpayer."

Jan 1, 1984