Search Documents

Dr R. E. Robinson, Pr. Eng., obtained a B.sc. (Chem. Eng.) cum laude from the University of the Witwatersrand in 1950 and a Ph.D. (Eng.) from the same University in 1953, where he was awarded the Haikes Memorial Medal for Industrial Chemistry. Professor G. G. Garrett was appointed Professor of Physical and :Fabrication Metallurgy in the Department of Metallurgy at the University of the Witwatersrand in June 1980, and in January 1984 he became Head of the Department. Mr P. A. van Wielligh, Pr. Eng., climbed the mining ladder in the hard way, starting as a Mine Surveyor in 1936 and working his way up as Chief Surveyor, Underground Manager, Mine Manager, and Consulting Engineer, to Executive Director, including the intermediate steps. Mr H. E. James, Pr. Eng., is a graduate in Chemical Engineering from the University of the Witwatersrand. Both his B.sc. degree (1961) and his M.sc. degree (1964) were obtained on bursaries, the former from Gold Fields of South Africa and the latter from the Atomic Energy Board. Mr G. Pienaar, Pr. Eng., obtained a B.Eng. (Met) in 1967 and an M.Eng. in 1973, both from the University of Pretoria. Dr A. K. Haines, Pr. Eng., obtained all his degrees from the University of Natal, finishing with a. Ph.D. in 1971. Mr B. C. Alberts, Pr. Eng., obtained his academic training at the University of Pretoria, where he was awarded B.sc. degrees in both agricultural engineering (1963) and mining engineering (1965). Mr H. C. van Zyl, Pr. Eng., holds B.sc. degrees in mining engineering (1968) and civil engineering (1972), both from the University of Pretoria.

Jan 1, 1984

By D. Wolfe, K. Reid, T. Nunn

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. In order to minimize front-end rejects, and to allow for high throughput, the ore top size at Aurora has been set at a nominal 125 mm. These relatively large lumps have a significant effect on both pump performance and pipeline pressure gradient. Current design methods underestimate the solids de-rating effect of lumpy slurries in pumps, and do not accurately describe the distribution or magnitude of the lump effect on pipeline pressure gradient. Data from the Aurora hydrotransport systems has been compiled, to quantify the effect of lumps on the pump head ratio and pipeline pressure gradient, and how this effect changes as lump ablation occurs along the length of the pipeline. A model has been built, using a logarithmic curve, which predicts the effect of 125 mm lumps on pipeline pressure gradient as a function of velocity and the distance from the start of a hydrotransport pipeline. This model is applicable only to Aurora hydrotransport operation, but similar models could be developed for other operations using the same methods. Using accurate pipeline pressure gradients and pump head ratios when designing future hydrotransport pipeline systems will help improve their reliability and operability."

Jan 1, 2014

By P Grieve, J L. Mauk

The Central Maratoto Valley in the Coromandel Peninsula contains a sequence of veins in pervasively altered dacite + andesites of the Waipupu Formation. We recognise at least eight different vein types: (1) pyrite stringers, (2) quartz + carbonate veins, (3) crystalline quartz veins, (4) carbonate veins, (5) chlorite + carbonate veins, (6) siderite veinlets, (7) siderite + carbonate veins and (8) carbonate + pyrite veins. The overall temporal trend of the veins is from early pyrite to quartz and then to late carbonate veins. Carbonate veins and pyrite stringers both form planar and irregular veins, whereas some carbonate veins have diffuse contacts with the wall rock. Gold and base metal sulphides are associated with some of the quartz + carbonate veins. Textures within the veins reflect open space filling and multi-phase reopening. A partial record of hydrothermal activity has been preserved by vein crosscutting relationships, hydrothermal alteration minerals and fluid inclusions. Hydrothermal alteration minerals display zonation from south to north. The alteration increases from unaltered to weak propylitic alteration of andesite in the south (MVRCDC1), to sericitic alteration of andesite and dacite in the north (MVRCDC3). The alteration assemblage is dominantly sericitic, with no adularia present, drawing parallels to the Thames region where there is no adularia.

Jan 1, 1999

By Michael Godard, Peter Cleyle

"Suncor Energy’s Project Millennium increased oilsands production capacity by an additional 95,000 barrels per day to its present level of 225,000 barrels per day. This massive venture included an expanded Mine, new Extraction and Upgrading facilities, as well as, steam and utilities infrastructuresIn the Primary Extraction process, removal of the bitumen from the oil sand begins with slurry preparation and is followed by primary , secondary and tertiary separation processes. The final cleaning step of the bitumen froth is the Secondary Extraction process, that removes residual water, mineral and solids to produce a clean diluted bitumen suitable for Upgrader feedstock.This paper will review the flowsheet of the Millennium Primary Extraction facility, from its recent commissioning through the ramp up to design production rates. In addition, new technologies in the Primary Extraction flowsheet will be reviewed.INTRODUCTIONAs conventional supplies of oil and gas are depleted in Canada, the Athabasca oil sands industry of Alberta becomes an increasingly important source of energy. Today, high quality crude from Alberta’s oil sands accounts for roughly 30% of Canada’s daily petroleum production. According to government projections, over the next 7 years, oil sands production is expected to more then double, and by 2010 more than half of Canada’s crude oil is expected to come from the oil sands.Oil sands deposits consist of a layer of sand saturated with bitumen covered by a muskeg overburden and underlain by silt and clay. The oil sand is mined where the overburden is economical to remove, typically less than thirty meters thick. The Athabasca oil sand deposits around Fort McMurrray is ideal for mining. Bitumen can be described as a diverse collection of hydrocarbons, organosulfur, and nitrogen compounds."

Jan 1, 2004

By Laurence McGonagle

"The Highland Uranium Project (HUP) is located approximately sixty miles northeast of Casper, Wyoming and is owned and operated by Power Resources, Inc. (PRI). With an annual production of680 tonnes (1.5 million lbs) U308, HUP is one of the largest uranium producers by in-situ leach (ISL) in the western world. Uranium is currently produced from four wellfields with a total flow rate of approximately 1,135 m3/hr (5,000 gpm). The carbonate leach solutions are processed by anion ion exchange at two satellite facilities located in close proximity to the wellfields. The loaded resin is transported by truck to a central processing facility for elution of the uranium. Uranium in the pregnant eluant is precipitated and washed prior to calcining.Wastewater from the satellite facilities is treated and used for irrigation at a Land Application Facility. The wastewater generated at the central processing facility is injected into a 2,750 m (9,000 ft) deep waste disposal well.When economical mining of the orebodies is complete, restoration of the groundwater is initiated. There are currently two wellfields at HUP undergoing ground water restoration. Phase I restoration consists of removal of the carbonate leach solution from the ore body. Phase II includes treating the withdrawn fluid with reverse osmosis and reinjection of the permeate into perimeter wells.Future plans include construction of additional satellite facilities at the Gas Hills Project and other economical deposits located within 240 km (150 mi) of HUP. The capacity of the central processing facility will be increased to 1,815 tonnes (4 million lbs) U308 per year by late 1999."

Jan 1, 1998

By J J. J Chen, J C. Zhao

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions. Metal refining is most efficient when fine bubbles are generated and uniformly distributed within the treatment tank. The application of some measuring technique able to detect this distribution within a non transparent operating treatment tank would be invaluable, enabling the optimisation of gas flow and impeller speed.   A technique has been developed to measure the pressure fluctuation levels at specific points in the water model. Comparison of these pressure fluctuation data with photographic evidence obtained in the water model suggests that the flow regime in the metal treatment unit may be determined using this technique.

Jan 1, 1995

Maintaining high carbon activity is vital to the efficiency of any Carbon-In-Leach or Carbon-In-Pulp process. Reduced activity can lead to longer residence times or gold losses in the tails. Regenerated carbon from the CIL circuit at Macraes Gold Mine was analysed for kinetic activity and composition over a 15 month period. An increase in kinetic activity during the time period was recorded, which was linked to reduced Na and Ca loadings. A laboratory simulation of the loading, stripping and regeneration of gold was developed and tested. Kinetic activities were obtained for synthetically fouled carbons following three circuits of the laboratory simulation. It was shown the competitive gold adsorption ability of xanthate fouled carbon (previously reported as a serious deactivator) could be significantly recovered following effective thermal regeneration. This ability was maintained in a subsequent circuit loading.

Jan 1, 1993

By J. J. Bezuidenhout

The waste-heat boiler is used within the Sulphide flash smelting process as the main dust and energy recovery unit. The large volume of off-gas discharged from the flash smelter is at a very high temperature (1350°C) and contains a significant dust load that subjects the downstream waste-heat boiler to tough and demanding conditions. The boiler cavity is especially prone to dust accretions, fouling, and corrosion caused by accumulation of molten particles and precipitation of sulphuric acid. Computational fluid dynamics (CFD) is applied within a qualitative study to model the flow and heat transfer distribution throughout the waste-heat boiler. The commercial CFD package, Fluent 6.2.16, was applied to a modified waste-heat boiler (23 m ×11 m ×5.4 m) within the Outokumpu flash smelting process. This investigation focuses on the geometric modifications to the typical boiler design, which includes elevation of the ceiling, placement of flow-obstructing baffles and radiation plates parallel within the flow path. Also investigated were various boiler operating conditions such as the circulation of process off-gas, air leakage from the dust discharging hoppers and variation in inlet gas composition. The geometric modifications had the desired effect of increasing the volumetric utilization and therefore enhancing heat transfer between the boiler surface and the gas stream and dust segregation. Introducing circulated off-gas at a rate of 20 m/s and at a 45° angle to the front of the waste boiler further enhanced cooling while reducing the high impact of the furnace-uptake gas-stream on the boiler ceiling. The placement of radiation plates was found to be very effective in enhancing the heat transfer surface and distributing gas flow within the boiler. These results present recommendations towards an improved waste-heat boiler design. Keywords: flash smelting, waste-heat boiler, CFD simulation, off-gas cooling.

Jan 1, 2008

By I. Nikolic

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

Stratiform lead-zinc mineralization at the Pegmont prospect occurs as a 4-6 m thick body interbedded within arkose, schist, amphibolite, and pegmatite of the Kuridala Formation in the Eastern Belt of the Lower Proterozoic of northwest Queensland.The overall structure of the body is that of a strongly crumpled east-dipping sheet. In detail it is subjected to complex and irregular deformation.Gossaneous outcrops of the mineralised body are anomalous in Pb-Zn-Ag content and have been traced, discontinuously, over about 36 km2 in a NNE-trending belt.Below the zone of oxidation, which reaches 25-40 m below the surface, the primary sulphides are galena, sphalerite, and pyrite.Drilling on a 2 km2 area near the discovery outcrops indicates fairly uniform grades of lead and zinc.Changes in thickness of the mineralised body are gradual.

Jan 1, 1977

Formation of either sodium jarosite or lead jarosite from concentrated chloride solutions containing small concentrations of sulphate has been demonstrated. Sodium jarosite is precipitated at 95-100°C from FeC13-FeCI2-NaCI-PbCI2 solutions to which was added Na2SO4 or Li2SO4 in amounts greater than 0.05 M. In the absence of alkali metal ions capable of forming jarosites, lead jarosite was precipitated from either FeCI3-PbCI2 or FeCI3-FeCI2-LiCI-PbCI2 solutions to which had been added small amounts of sulphate. Many of the factors affecting jarosite precipitation from chloride solution have been elucidated, and the most critical were sulphate concentration and initial pH. Concentrations of HCI in excess of O. I M essentially suppressed the production of jarosite in chloride media. Alkali jarosite, precipitated in the presence of dissolved lead, incorporates a small amount of this metal into the alkali jarosite lattice. Small but significant amounts of copper can also be incorporated into alkali jarosite and the amount is further increased in the presence of lead. Other divalent base metals such as Zn, Cd or Ni are not significantly precipitated. Sulphate control in either FeCI3 or FeCl3-NaCI leaching systems could likely be maintained by jarosite precipitation provided that the acid concentration of the solution was low.

Jan 1, 1981

By Dean Workman

Located in downtown New York City, this project necessitated an innovative conveyor design for successful muck removal. This paper will discuss the technical challenges and engineering solutions of the muck transport system which consists of every commonly recognized version of a belt conveyor. The elaborate system includes a TBM conveyor integral to the back-up system, a wall-mounted extensible conveyor, a crown-mounted transfer conveyor, a floor-mounted fixed-length conveyor, a pocket-belt vertical conveyor, three cascading overland conveyors, and one radial stacker. The most challenging design element was an over-land conveyor featuring a box truss for muck transportation over Northern Boulevard while simultaneously going under the Queens Plaza railroad viaduct. An overview of the project is provided along with the following topics: developing final plans from the proposal concept, interfacing with existing works, communication with the joint venture, and complying with local regulations.

Jan 1, 2008

By J M. Parr, P M. Herzig, J B. Gemmell, S D. Scott

PACMANUS is an actively-forming seafloor analogue of volcanic-hosted massive sulfide orebodies, situated on the crest of an andesite-dacite-rhyodacite ridge overlying rifted older arc crust in a back-arc basin. Hydrothermal deposits range from Mn-oxide crusts to Cu-Zn-rich massive sulfide mounds and chimneys containing significant Au and Ag. Preliminary data suggest a substantial magmatic component to fluids and metal sources, and we speculate that PACMANUS is the cap to a complete hydrothermal system including subvolcanic and intrusive-related mineralisation.

Jan 1, 1995

By D. J. Duck

INTRODUCTION Construction of the 3,600,000 kilowatt Third Powerplant at Grand Coulee Dam started in late summer 1967 approximately one year after authorization by Congress. The project was made possible by a treaty with Canada providing for cooperative development of the Columbia River which was signed in 1961 and ratified in 1964. Description of the Work The existing Grand Coulee power complex consisted of a dam and two powerplants with a switchyard serving each plant, one on each bank of the river. See Fig. 1. The switching facilities were connected to transformers at the powerplants by overhead 230-kilovolt and 115-kilovolt tie circuit conductors. [ ]

Jan 1, 1997

Judicious placement of a range of geotechnical instruments was employed at the Tasmania gold mine, Beaconsfield, Tasmania, as a key strategy in the monitoring of rock mass conditions over the past four years. The range of instruments employed included vibrating wire stress-meters and hollow inclusion cells to monitor changing stress conditions, resistance wire and multipoint borehole extensometers to monitor the impact of stress changes on the integrity of the rock mass, and instrumented cable bolts and threadbar bolts to monitor the static and dynamic impact of rock mass changes on the installed ground control system. Initially the monitoring was of a qualitative nature, monitoring change from the time of installation. The value of the output was considerable when considered in relation to the ongoing seismic record which was also being monitored. It was clear from the seismic record and the monitoring results that stope blasting was the primary trigger for changing rock mass conditions. However, it was unclear how well observed behaviour was reflecting conditions anticipated by elastic numerical modelling. The latter had predicted significant stress increase in the near field of man-access footwall development. Qualitative monitoring and visual inspection did not support the modelling prediction, and this led to a program of quantitative measurement being undertaken. Measurement of the absolute stress condition in the backs of footwall development immediately adjacent to monitoring hollow inclusion cells provided the benchmark for tracking quantitative stress change. The program provided insight into the evolution of principal stress field magnitude and orientation in relation to rock mass change observed with extensometers and instrumented ground control elements, as well as providing a degree of calibration between the elastic numerical modelling and the virgin stress field. Calibrated monitoring data has also provided a useful benchmark for finite element modelling which is to be used for future mine-wide design.

Nov 25, 2010

By Mostafa Benzaazoua, Bruno Bussière, Philippe Poirier, Denis Bois

"Environmental desulphurisation is an attractive alternative for the management of acid generating tailings. Non selective froth flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works (McLaughlin and Stuparyk, 1994; Bussière et al., 1995; 1998; Benzaazoua et al., 2000a,b; 2002). This process can reduce the volume of problematic tailings to manage, by making a sulphide fraction concentrate. The desulphurized tailings can then be used as a moisture retention layer in a cover with capillary barrier effects to prevent acid mine drainage.In this paper, the authors present the results from different laboratory and pilot scale flotation tests which confirm that low sulphide, non-acid generating tailings can be produced by froth flotation. It is also demonstrated that the sulphide concentrates obtained from desulphurisation, when mixed with binders gave good long term results in terms of mechanical behaviour, thus demonstrating that the sulphide fraction can be used for paste backfill material. From previous work (Bussière et al. 1998, 1999) on the evaluation of the operating and capital costs of the desulphurisation process for different ore types, the use of desulphurized tailings to create a dry cover was then studied for several scenarios. The desulphurisation process was compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation and the advantages and disadvantages of desulphurisation are presented as well as the costs of this method of AD prevention.INTRODUCTIONThe principal environmental problem of the mining industry today is the generation of acidic drainage (AD) resulting from the natural oxidation of the sulphides in mine tailings. This phenomenon involves the generation of acidity which increase the amounts of toxic metals in the waste water released into the environment by a mine. The environmental impact of the AD has been described in detail in previous work (e.g. Down et Stocks, 1977; Ritcey, 1989; Gray, 1997; Ripley et al., 1996; Aubertin et al., 2002)."

Jan 1, 2004

By S. Schina

Part of the Imittos Western Peripheral Motorway in Athens is the twin road tunnel in the vicinity of American College, with 20m excavation diameter. In the paper, the environmental and other requirements, the geometry and the geological – geotechnical characteristics of the rock formations in the construction area are given. Information regarding the modeling and analysis methods that are used for the design of the temporary support, the final lining and the wedge and slope stability analysis is described thoroughly. Finally, the results of the analyses are compared with these of measurements and general remarks during the construction of the tunnels.

Jan 1, 2001

By Adrian Daniel

"Dating back to 1934, Con Mine is located directly south to the city of Yellowknife in the NWT, Canada. With mill operations ceasing in 2004, a challenging surface remediation situation resulted which required the treatment of close to 40,000 m3 of Arsenic impacted material.Through much of the period of 1941 to 1970, Con Mine treated their refractory arsenopyrite ore through the use of an Edwards Heath roaster. With mounting environmental pressure and through Canadian governmental studies during 1950 to 1970, attention was directed to the Arsenic Trioxide material being collected by two Doyle scrubbers on the Con’s roaster stack. In 1970, the roaster was decommissioned leaving the resulting Arsenic material in two containment areas on surface.As a result of Con Mine entering into remediation in 2004, the Con’s autoclave, commissioned in 1992, was dedicated to the immobilization of high impacted Arsenic material through the combination of excess Iron under high temperature and oxygen overpressure. Examined, herein, is the history and chemistry of the Con Mine autoclave as well as the two stages of chemistry for the Water Treatment Plant used to remove arsenic, heavy metals and WAD cyanide from tailings water. Simplified capping plans of the tailing containment areas and a high arsenic impacted area are also presented.INTRODUCTION TO CON MINECon Mine (Con) is situated just south of the City of Yellowknife in the North West Territories (NWT) Canada and is bounded locally by Yellowknife Bay (North Extension of Great Slave Lake) to the east and Kam Lake to the west (Figure 6). The discovery of gold at Con was made in 1934 and mineral rights were acquired by Consolidated Mining and Smelting Limited (Cominco) and Falconbridge soon thereafter. Nerco Minerals Limited (Nerco) took control in 1986 and in 1993, was subsequently sold to, Miramar Mining Corporation which in turn was purchased by friendly takeover involving Newmont Mining in November 2007 as a result of acquiring the Miramar’s Hope Bay project. Con’s underground operations ceased in September 2003 and have since entered into the remediation of the site. The current surface lease holdings are about 340 Hectares (Table 1) which sits on top of the Archean-aged Yellowknife Greenstone Belt."

Jan 1, 2009

In a previous paper of this series (1) ,t it was shown that during the creep of single crystals of lead, deformation proceeded to some extent by means of slip on the octahedral plane. This was demonstrated by the formation of slip lines on the surface of the specimens. At first, a few broad bands appeared after a small amount of extension had taken place; then, as extension proceeded, more and finer lines made their appearance until the whole of the specimen surface was covered.The present paper deals with the process of deformation of the creep specimens as revealed by X-ray examination..By the use of this method, the changes taking place in the crystal structure can be observed.EXPERIMENTAL METHODThe method of preparation of the specimens, their size and the purity of the lead employed have been reported elsewhere (1). At frequent intervals, the specimens were dismantled from the test rack and X-ray back reflection photographs were taken. The specimens were so marked and set up on the X-ray machine that the same spot on the specimen surface was always examined.Copper radiation was employed, the tube voltage and current being 45 kV. and 25 m.a. respectively and the exposure time 2 hrs. The slit diameter was 1 mm.

Jan 1, 1941

The Mount Lyell Mining Field is Australia's chief productive source of copper. It is situated near Queenstown, on the western flanks of the West Coast Ranges, about 20 miles from the west coast of Tasmania (Fig. 1).The following observations on the mineral composition of the copper ores of the Mount Lyell Field are based on a...

Jan 1, 1939