Search Documents

By Michael Olmsted

Inspection of boreholes prior to blasting can result in cost reductions as well as increases in efficiency and safety. Until recently, borehole inspection was performed in two manners. For simple inspections, a flashlight was used to view the upper part of the hole. More thorough inspections were performed with long tool strings developed for oil field applications. Borehole inspection tools developed specifically for mining and blasting applications have now been developed. Video Cameras developed for borehole inspection have been in service for several years. Now measurement tools are available, developed specifically for mining.

Jan 1, 2000

By B. Amadei, F. Tonon

Rock stress measurement is cast in the more general context of the determination of boundary conditions for rock engineering. A study on the effect of elastic anisotropy on underground excavations reveals that this effect is actually controlled by the imposed boundary conditions. Applications to tunneling and to the Underground Research Laboratory (URL), Canada, exemplify a procedure for boundary condition estimation formerly developed by the authors. The procedure displayed fast convergence despite the complex geometry, and the high degree of non-linearity of the models. In the URL application, the 3-D model was able to completely reproduce the complex measured stress pattern, and the 90° rotation of the principal in situ stresses with depth. In order to reliably estimate the boundary conditions reproducing the current in situ state of stress, response measurements of the rock mass to current disturbances are necessary as input data. La mesure des contraintes in situ tombe dans le domaine général de la détermination des conditions aux limites pour les problèmes de mécanique des roches. Une étude sur le rôle de l’anisotropie élastique sur les excavations souterraines montre que ce rôle est contrôlé par les conditions aux limites qui sont imposées. L’application aux tunnels et au Laboratoire Souterrain de Recherche (URL) au Canada, nous permet de présenter une méthode de détermination des conditions aux limites. La méthode converge rapidement bien que le géométrie soit complexe et que le problème soit non-linéaire. Pour le URL, le modèle 3D est capable de reproduire la distribution des contraintes qui ont été mesurées ainsi que la rotation de 90 degrés des contraintes in situ avec la profondeur. Afin de déterminer avec précision les conditions aux limites responsables pour la distribution actuelle des contraintes, la réponse du massif rocheux doit être connue et mesurée. In der Felsentechnik sind die Spannungsmessungen in Gestein an die Bestimmung der Randbedingungen gebunden. Eine Studie legt dar, dass der Effekt elastischer Anisotropie in unterirdischen Aushoehlungen von den Randbedingungen kontrolliert ist. Eine von den Authoren entwickelte Methode zur Bestimmung der Randbedingungen wird an Beispielen im Tunnelbau und im Underground Research Laboratory (URL) in Kanada illustriert. Auch bei komplexer Geometrie und einem hohen Grad an Nicht-Linearitaet zeigt diese Methode ein schnelles Konvergenzverhalten. Ein 3D-Model und dessen 90° Drehung der lokalen Hauptspannungen mit der Tiefe, kann bei einer URL Anwendung vollstaendig reproduziert werden. Um mit dieser Methode die Randbedingungen zuverlaessig abschaetzen zu koennen, werden der gegenwaertige lokale Spannungszustand sowie die Antwort des Gesteins und die resultierenden Stoerungen als Eingabedaten benoetigt.

Jan 1, 2003

By Elsa Olivetti

Life cycle assessment (LCA) is used increasingly as a tool to provide quantitative metrics of environmental impact and inform early stage materials selection decisions. One common challenge in LCA stems from allocation of burden when multiple adjacent products share some of the same processes. A critical example of this is the partitioning of benefit or burden at product disposition in open-loop recycling scenarios. This work reviews the challenge of allocation and investigates the various methods proposed for allocating end-of-life (EOL) burden. Specifically this work examines whether these methods lead to different results and explores the trends in allocation method bias for or against particular materials classes.

Jan 1, 2010

By Thierry Bernard

For many years now electronic initiation has brought the time parameter to the centre of blast designs forever. Although this parameter existed before the era of electronic detonators, Blasting engineers or blasters could not directly handle it; technology imposed it. Only discrete values were available. Today, the fact that we can choose any detonation time for an explosive charge questions the viability of most of the rules applied for blast design. Thus, the very famous charge per delay method, that enables a level of vibration to be forecast at a given distance (“Chapot’s law”), is no longer necessarily valid when using electronic initiation. Therefore, it must be approached in a totally different manner. The KUZ-RAM formula, that allows fragmentation to be forecast, is also subject to the same distortion. The aim of this article is to show how the calculation laws used for blast design are influenced by the time parameter (sequence) and how we can efficiently make the most of this, in particular for vibrations. Copyright ©

Jan 1, 2005

By M Simpson

Greywackes of the greater Auckland Region (Brynderwyn Hills to Hamilton), when considered on a regional scale, have characteristic ranges of physical, mineralogical and other properties. Some properties (eg density, porosity, crushing resistance, clay index) generally cluster and correlate with the basement greywacke facies, regions and terranes recognised by geologists, and their diagenetic/metamorphic level. Other local factors, particularly variations in mineralogical composition, nature of matrix cement, grain size, and degree of weathering may produce aberrant properties. Some of these local variations, when extreme, have the potential to affect the aggregateÆs performance in roading or the concrete industries.   Smectite and the zeolite laumontite are the major deleterious minerals occurring in fresh greywacke rocks of the Auckland region, although weathered rocks may contain halloysite, an expanding member of the kaolin clay mineral group. These minerals, when found in abnormally high levels in greywackes cause expansion effects in the aggregate. Currently there are inconsistencies in the detailed correlation of shrinkage, clay index, clay mineral content and intrinsic expansion data that need further research to resolve them.  

Jan 1, 2007

By René Lefebvre

Numerical simulations of the physicochemical processes related to acid rock drainage (ARD) in the Sugar Shack South rock pile of the Questa Mine were performed with the TOUGH AMD simulator. The objectives were to 1) identify the main processes responsible for observed present-day conditions, 2) provide an estimate of gas phase humidity transfer, and 3) give a preliminary indication of the potential impact of closure involving the installation of an alluvial soil cover. Modeling results indicated that the mine rock geometry (thin layers placed along steep mountain slopes) favors the onset of strong thermal air convection. Simulations also indicate that resloping the piles would not significantly reduce convection and oxidation. For simulation purposes, a potential cover with the permeability range of a local alluvium was investigated and found to be of questionable effectiveness since its permeability can exceed the value of 3x10-13 m2 required to prevent thermal air convection and reduce ARD.

Nov 1, 2002

By Enrique Ibarra, Manuel J. Mendoza

"Abstract: This paper describes the current state-of-practice for the design of cast-in-place drilled shafts in granular soils under axial loading, addressing recent advances that take into account the surrounding soil grain size distribution and their behavior. The important role of the gravel content in the shaft response under axial loading is emphasized. Usual design approaches in Mexico are described, and the results of load tests from different sources are discussed. The analysis emphasizes the primary contribution of the lateral area of shafts to their axial bearing capacity, raising doubts regarding the common local idea of “point bearing shafts”. Finally, some lines of research are noted to permit advances in the important field of deep foundations. 1 INTRODUCTIONIn Mexico, cast-in-place drilled shaft foundations are widely used to support various structures in the west area of Mexico City, where alluvial and volcanic deposits predominate. Deep foundations are also used in modern construction works located in other major cities of Mexico. In fact, the use of drilled shafts for tall buildings and overpasses in the center of Guadalajara as well as in transportation works related to the Metro and roadways in Monterrey is well known. It is worth mentioning that these same structures have been applied in road bridges throughout the country.Procedures for pile construction in Mexico have been basically the same for the past 20 years (Paniagua et al., 2005); however, modern equipment has been incorporated into the construction industry, including innovations in sludge-drilling technology, control and the quality of the castings. In addition, novel and efficient procedures such as construction with continuous auger displacement piles have been implemented (Auger Cast in Place, ACP) and have begun to be used locally with success (Schmitter and Paulin, 2006).However, it can be argued that the technological developments that have resulted in more efficient construction procedures have not included a breakthrough in the full understanding of the phenomena or basic mechanisms of load transfer from piles to the surrounding subsoil and therefore in supported, tested and practical design methods. This is particularly true when seeking to determine the unit side shear strength of shafts drilled in granular media with gravels, where it has been observed that the commonly used calculations developed for sands underestimate the load-bearing capacity by frictionin a most important way. Due to the above reasons, it seemed appropriate to present in this paper a review of the current stateof- practice in Mexico for the design of cast-in-place drilled shafts, particularly in granular media, highlighting some recent advances and research that takes into account the grain size distribution and behavior of granular soil."

Jan 1, 2014

By E N. Sajin

The final arsenic bearing waste products at the majority of metallurgical and chemical enterprises are cakes in which arsenic is present in the form of calcium arsenate. Burial of cakes demands construction of special burial sites and does not guarantee reliable protection from arsenic penetration into the ground and surface waters. Under laboratory conditions we developed technology for processing calcium arsenate cakes with obtaining low toxic products suitable for long-term storage, meeting environmental requirements. The investigations have shown that thermal processing of briquetted mixtures of cakes containing 15 - 20 per cent weight of pyrite under the temperature of 873 - 923¦K during 45 - 60 minutes gives briquettes sufficiently hard for transportation and long-term storage. Arsenic, under high sulphidisation temperature is bonded into low solubility non-volatile iron sulphide bearing compounds having chemical properties similar to the natural arsenic compounds. Solubility of the obtained products in neutral, acid and alkaline media was investigated during long period of time (three to 12 months). It was determined that arsenic content in the solutions did not exceed the norms for cultural and welfare basins and fish-ponds.

Jan 1, 2002

By Rimas Pakalnis, Tom Brady, Lewis Martin

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate weak rock masses (such as are associated with operations in the Carlin Trend in Nevada) into existing design relationships. The original database that led to most of the empirical design relationships presently employed in hard-rock mining was derived from fair-to-good-quality rock. In this study, the relationship between weak rock quality and opening design (nonentry/entry methods) is being investigated. The common factor in all mines is a weak back or wall. This work attempts to provide tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

By Jurgen te Kook

State-of-the-art for subsidence calculation are stochastical models. Although these models were successfully used all over the world they have their limitations due to the fact that they are not based on mechanical laws. For example the models did not take the rock mass structure and the rock mass characteristics into account. Therefore in a research program the skills of geomechanical numerical models for subsidence calculation were investigated. A case study shows that numerical models which are in principle based on the elastic theory are suitable for subsidence prediction. Due to the principles of these models the results are not sufficient in the case of multiple seam extraction. More extended geomechanical numerical models like FLAC and UDEC were investigated in further steps of the research work. Up to now large area geomechanical models require unrealistic long calculation times if the level of detail is similar to that of small scale calculations. Due to this it was necessary to implement a simplified description of the rock mass structure and characteristics. Different case studies show that this approach is successfull for subsidence calculation by numerical geomechanical models even for multiple seam extraction.

Jan 1, 2008

Provide the mining industry with a simple, accurate and readily available means of measuring the gas flow from pipe outlets such as gob holes Approach The Bureau of Mines conducted laboratory studies to establish correction or method factors for anemometers when used to measure gas flow from pipe outlets. Using the Anemometer Anemometers are used by the mining industry to make air velocity measurements in mine entries. Although the instrument has no appreciable influence on the airstream in mine entries, especially since the cross-sectional area of an entry is much larger than the cross-section of the anemometer, correction or method factors are used to correct the center line anemometer velocity to average velocity. This adjustment is made because the air velocity in a mine entry is highest in the center and lower at the sides. Anemometers can be used to measure gas flow from small diameter pipe outlets; however, since the instrument diameter is much larger than one-sixth of the pipe diameter, it will influence the air-stream from these small outlets. Resulting velocity measurements are erroneously high by as much as 30 percent. Method factors must be applied to such anemometer measurements taken at pipe outlets. Through a research investigation the Bureau of Mines established a set of method factors for center-line anemometer readings taken at the discharge end of 4-to 8-inch diameter pipes. These method factors were combined with method factors which were developed by the National Coal Board of Great Britain for 12-to 30-inch diameter pipes. The anemometer was mounted on the end of a short rod and held against the pipe for support except on the 4-inch pipe where the instrument was started and stopped remotely to prevent hand interference with the air-stream during measurements. Method factors were determined by comparing the anemometer measurements at the pipe outlet to the true average airflow which was simultaneously determined upstream by venturi measurements. Consequently, a method factor is nothing more than the ratio of the true velocity to an anemometer measurement.

Jan 1, 1987

By D. J. Bauer

Oxidation of mixed lanthanide solutions with ozone at pH 4.5 and at ambient temperature resulted in precipitation of 98 percent of the original cerium present. Corresponding cerium purity was increased from 50 to 98 percent. A second ozone oxidation-precipitation step produced cerium of 99.9 percent purity in high yield from the 98-percent-pure material. Alternately, ozonation at pH 6.5 and 85° C differentially precipitated cerium and rare-earth elements heavier than cerium and left 89 percent of the original lanthanum in solution at a purity of 95 percent. Subsequent recovery of cerium from the heavier rare-earth elements in the precipitate was accomplished by dissolving the precipitate in dilute mineral acid and reoxidizing the cerium with ozone at pH 4.5 and at ambient temperature. The filtrate contained an enriched praseodymium-neodymium-samarium-europium mixture that is amenable to separation by ion exchange or solvent extraction.

Jan 1, 1968

By P Meehan, R McAree, Z Guan

Equipment maintenance is 30 - 50 per cent of the operating costs for a typical mining company. While this is substantial, its importance is beyond its significance as a cost heading. Modern mining requires large amounts of investment in capital infrastructure and equipment to produce a product sold at a low unit cost. To stay competitive, such a business has to focus on full realisation of its capital investment, ie sustained production at high levels. Maintenance plays an essential role in achieving this goal. Mining companies typically use a mix of breakdown or corrective maintenance, planned maintenance, and some condition-based maintenance. The share of breakdown maintenance has been coming down through more effective planned maintenance and better condition monitoring tools. Planned or preventive maintenance (PM) is playing an increasingly important role in todayÆs mining maintenance. This is the suite of inspection and repair/replacement actions performed at scheduled time intervals as part of a preplanned activity. The activities are scheduled well in advance and, usually, the current wear-state of the machine is irrelevant. For example, the replacement of a major gear may have been planned 18 months in advance; replacement is carried out when the time comes regardless of the actual condition of the gear. The PM costs are significant and include direct cost of parts and labour as well as the opportunity cost of lost production while the machine is under maintenance. It is important to identify the optimum PM effort because over-maintenance should be avoided as much as under-maintenance. A new concept called severity-based maintenance is introduced in this paper. We have seen that measuring equipment ageing in mining merely by counting the engine hours is a very imprecise way of planning and scheduling maintenance because the damage accumulated in one hour varies enormously from operator to operator and with changing pit conditions. We recommend continuous monitoring of duty on all major equipment. This is feasible without having to fit out the machine with an army of sensors because most of the physical sensors required by dutymeters are already installed and maintained as part of the existing performance monitors. While the investment is modest, the potential benefits are huge and can be grouped under three headings:Immediate benefits will come from providing operators with direct feedback on the effect of their behaviour on machine health and training them to use this feedback to correct their operating style. The equipment can operate closer to the limits of capacity, producing more without unduly sacrificing the availability by monitoring and controlling the severity of the operation, ie the duty on the machine. Longer term benefits accrue from establishing correlations between actual time to failure data and measured equipment duty and using these correlations to optimise maintenance effort as well as planning new equipment purchases and warranty conditions.

Jan 1, 2002

By Jr. Blanchette, Claude Bazin, Paul Blatter

"Reporting of the gold production during a month implies to estimate the mass of gold that is processed by a mill, recovered as dorés, lost to the tailings and the change of gold inventory within the plant equipments. Carbon in pulp and/or carbon in leach tanks may contain gold inventory as large as 72 000 g (2 200 troy oz) of gold which needs to be estimated from measurements obtained from sampling the material contained in a tank. Sampling and analysis introduce measurement errors that could be systematic and/or random. This paper examines the effect of measurement errors on the estimation of the gold inventory and on the variation of the inventory in the carbon in leach tanks of the Agnico-Eagle Mines Limited Lapa concentrator. Results of the analysis demonstrate that the inventory is measured with ±10% reproducibility, while the variation of inventory used for mass balance is known with ±300% reproducibility.INTRODUCTIONThe preparation of a production report implies to reconcile measured data with the constraint of material balance over the considered period of production. The sampling and data reconciliation problems were recently reviewed by Morrison (2008) and Jansen (2009a; 2009b). Typically a production report is prepared to cover a period over which the mass conservation hypothesis can be considered valid. In gold processing plants, the change of inventory can seldom be neglected and plays a significant role in material balance calculations. This is particularly true for circuits using carbon adsorption, where the complete cycle of carbon is measured in days.In a 2000 t/d gold ore processing plant, the inventory can be as large as 140 000 g of gold in gravity concentrator bins, carbon in pulp tanks and in the electrolysis circuit. This is equivalent to the mass of gold that fed the circuit during 10 days of operation with 7 g/t feed assays. The change of inventory may therefore strongly impact the production figures and especially the plant recovery at the end of a week or a month. Despite the financial impact associated with gold inventory, few publications are devoted to the subject. Bruington (1991) and Morrison (2008) discussed the problem and stressed the need for the development of reliable methods to estimate the gold inventory in carbon in pulp or carbon in leach circuits."

Jan 1, 2011

By Carlos A. Prato, Federico Pinto

"ABSTRACTThe design of drilled shafts often incorporates large factors of safety, for which settlements under service loads are highly influenced by the initial elastic stiffness. In the case of groups of drilled shafts with typical spacing, the elastic shaft-soil-shaft interaction dominates the behavior even for loads close to the bearing capacity, for which the initial stiffness is a key parameter in the design. This paper describes typical trends in results obtained by means of different approaches currently available in the literature for the evaluation of the initial stiffness of a single shaft. An experimental technique that provides a rapid and inexpensive means for the evaluation of the initial stiffness is described, and the results obtained for typical cases are compared with analytical predictions.IntroductionThe behavior of drilled shafts under axial loads is generally governed by the initial stiffness, as the factors of safety considered in design are often large, due to a superposition of conservative assumptions on soil properties and expected loads. In the case of shaft groups, the initial elastic stiffness plays a major role together with the elastic group effects, as nonlinearities tend to localize around the shafts and have a lesser effect than elastic deformations on adjacent elements (e.g., Leung et al., 2010). An accurate characterization of the initial stiffness is thus warranted for the analysis of drilled shafts and shaft groups under service loads.Initial stiffness of shafts may be estimated on the basis of soil stiffness and structural properties of the element by means of numerical methods (e.g., Pinto and Prato, 2006), as well as analytical methods (e.g., Randolph and Wroth, 1978). The soil stiffness may be determined by means of geophysical tests (e.g., Spectral Analysis of Surface Waves, SASW, Stokoe et al., 1994), or correlations with Standar Penetration Test (SPT) blowcounts or Cone Penetration Test (CPT) resistances (e.g., Sabatini et al., 2002).The initial stiffness may also be measured on drilled shafts by means of load tests. Static load tests (SLT), however, have some limitations on measuring small deflections, for which the initial stiffness is often extrapolated by means of large strain measurements (e.g., Chin, 1970), where the SLT measurements are more accurate."

Jan 1, 2014

Process Study on Some Ag-Cu-Pb-Zn Polymetallic Ore in South China

Sep 13, 2010

By K. Ward

The Environmental Protection Agency (EPA) is beginning to provide compliance assistance visits to various industries, including mining, for Emergency Planning and Community Right-to-Know Act (EPCRA) compliance. The EPA inspectors may consist of a multi-media team deployed to review systems and procedures for EPCRA Sections 302, 304, 311, and 312. The Team’s focus may include emergency response plans, training programs, qualifications of personnel, and release notification protocols. This presentation takes a look at the EPCRA compliance challenges faced by Arizona copper mining and processing facilities.

Jan 1, 2001

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By Bruce Clements

The Bagdad mill, located near Bagdad, AZ, was built in 1977 with a designed mill capacity of 36.3 kt/d (40,000 stpd). An autogenous mill-ball mill crusher (ABC) grinding circuit was chosen. The original mill contained three independent grinding circuits. Each contained one 9.75m-diam x 4-m-long (32-ft-diam x 13-ft-long) fixed-speed autogenous mill, a4.7-m-diam x 6.7-m- long (15.5ft-diam x 22-ft-long) ball mill and one 2. 1-m-diam (7-ft-diam) short head cone crusher. Total installed power per grinding circuit was about 8.4 MW (11,350 hp), with 5.9 MW (8000 hp) in the autogenous mill, 2.2 MW (3000 hp) in the ball mill and 261 kW (350 hp) in the crusher (Fig. 1). The autogenous mills were designed to be able to operate semi-autogenously. However, they were never converted to semiautogenous grinding (SAG) mills. As a result of this design, only about 4.1 MW (5450 hp) of the designed power is used in the autogenous mills. The grinding circuits are closed, with 2.4 x 6 m (8 x 20 ft) double-deck vibrating screens. A series of conveyors re- turn screen oversize underneath the mill coarse ore stockpile to feed the crushers. Variable speed belts feed the crushers and control power draw. Crusher product reports directly to the tail end of the autogenous mill feed belt (Fig. 2). A magnetic sensor detects tramp iron in the autogenous mill-crusher circuit.

Jan 1, 1992

By Susan B. Robertson, Gregory E. Hinshaw

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100%can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.